Flow and heat transfer with prescribed skin friction in a rotating fluid

This paper investigates the rotating flow and heat transfer of a viscous fluid induced by a stretching surface. The nonlinear problem subject to a given skin friction at the boundary is solved. Analytic solution is obtained using homotopy analysis method. The velocity, temperature, and stretching velocity is calculated for different values of the rotation parameter (λ). The obtained results are compared with the well known results of rotating flow induced by a stretching surface by using four sets of boundary conditions. Copyright © 2011 John Wiley & Sons, Ltd.     

Effects of thermal radiation and variable fluid viscosity on stagnation point flow past a porous stretching sheet

Similarity analysis is performed to investigate the structure of the boundary layer stagnation-point flow and heat transfer over a stretching sheet subject to suction. Fluid viscosity is assumed to vary as a linear function of temperature. Thermal radiation term is considered in the energy equation. The symmetry groups admitted by the corresponding boundary value problem are obtained by using a special form of Lie group transformations viz. scaling group of transformations. With the help of them the partial differential equations corresponding to momentum and energy equations are transformed into highly non-linear ordinary differential equations. Numerical solutions of these equations are obtained by shooting method. It is found that the horizontal velocity increases with the increasing values of the ratio of the free stream velocity to the stretching velocity. Velocity increases with the increasing temperature dependent fluid viscosity parameter when the free-stream velocity is less than the stretching velocity but opposite behavior is noted when the free-stream velocity is greater than the stretching velocity. Due to suction, fluid velocity decreases at a particular point of the surface. Temperature at a point of the surface is found to decrease with increasing thermal radiation.     

Analytical solution to stagnation-point flow and heat transfer over a stretching sheet based on homotopy analysis

This paper is concerned with two-dimensional stagnation-point steady flow of an incompressible viscous fluid towards a stretching sheet whose velocity is proportional to the distance from the slit. The governing system of partial differential equations is first transformed into a system of dimensionless ordinary differential equations. Analytical solutions of the velocity distribution and dimensionless temperature profiles are obtained for different ratios of free stream velocity and stretching velocity, Prandtl number, Eckert number and dimensionality index in series forms using homotopy analysis method（HAM）. It is shown that a boundary layer is formed when the free stream velocity exceeds the stretching velocity, and an inverted boundary layer is formed when the free stream velocity is less than the stretching velocity. Graphs are presented to show the effects of different parameters.     

Stagnation-point flow of a viscoelastic fluid towards a stretching surface

An analysis is made of the steady two-dimensional stagnation-point flow of an incompressible viscoelastic fluid over a flat deformable surface when the surface is stretched in its own plane with a velocity proportional to the distance from the stagnation-point. It is shown that for a viscoelastic fluid of short memory (obeying Walters’ B′ model), a boundary layer is formed when the stretching velocity of the surface is less than the inviscid free-stream velocity and velocity at a point increases with increase in the elasticity of the fluid. On the other hand, an inverted boundary layer is formed when the surface stretching velocity exceeds the velocity of the free stream and the velocity decreases with increase in the elasticity of the fluid. A novel result of the analysis is that the flow near the stretching surface is that corresponding to an inviscid stagnation-point flow when the surface stretching velocity is equal to the velocity of the free stream. Temperature distribution in the boundary layer is found when the surface is held at constant temperature and surface heat flux is determined. It is found that temperature at a point decreases with increase in the elasticity of the fluid.     

Flow of a power-law nanofluid past a vertical stretching sheet with a convective boundary condition

A boundary layer flow of a non-Newtonian fluid in the presence of nanoparticles is examined. The flow is caused by a vertical stretching sheet. Convergence of the solution obtained is checked. The values of velocity, temperature, skin friction, and Nusselt number in the boundary layer are obtained.     

Momentum and heat transfer in the magnetohydrodynamic stagnation-point flow of a viscoelastic fluid toward a stretching surface

An analysis is made of the steady two-dimensional stagnation-point flow of an incompressible viscoelastic fluid over a flat deformable surface when the surface is stretched in its own plane with a velocity proportional to the distance from the stagnation-point. It is shown that for a viscoelastic conducting fluid of short memory (obeying Walters’ Bʹ model), a boundary layer is formed when the stretching velocity of the surface is less than the inviscid free-stream velocity and velocity at a point increases with increase in the Hartmann number. On the other hand an inverted boundary layer is formed when the surface stretching velocity exceeds the velocity of the free stream and the velocity decreases with increase in the Hartmann number. A novel result of the analysis is that the flow near the stretching surface is that corresponding to an inviscid stagnation-point flow when the surface stretching velocity is equal to the velocity of the free stream. Temperature distribution in the boundary layer is found when the surface is held at constant temperature and surface heat flux is determined. It is found that in the absence of viscous and Ohmic dissipation and strain energy in the flow, temperature at a point decreases with increase in the Hartmann number.     

Effects of variable fluid viscosity on flow past a heated stretching sheet embedded in a porous medium in presence of heat source/sink

The boundary layer flow and heat transfer of a fluid through a porous medium towards a stretching sheet in presence of heat generation or absorption is considered in this analysis. Fluid viscosity is assumed to vary as a linear function of temperature. The symmetry groups admitted by the corresponding boundary value problem are obtained by using a special form of Lie group transformations viz. scaling group of transformations. These transformations are used to convert the partial differential equations corresponding to the momentum and the energy equations into highly non-linear ordinary differential equations. Numerical solutions of these equations are obtained by shooting method. It is found that the horizontal velocity decreases with increasing temperature-dependent fluid viscosity parameter up to the crossing-over point but increases after that point and the temperature decreases in this case. With the increase of permeability parameter of the porous medium the fluid velocity decreases but the temperature increases at a particular point of the sheet. Effects of Prandtl number on the velocity boundary layer and on the thermal boundary layer are studied and plotted.     

Effects of thermal stratification on flow and heat transfer past a porous vertical stretching surface

The aim of this paper is to present the boundary layer flow of viscous incompressible fluid due to a porous vertical stretching surface with a power-law stretching velocity in a thermally stratified medium. Using a special form of Lie group transformations viz. scaling group of transformations, similarity solutions for this problem are obtained. The equations are then solved numerically. With increasing values of the stratification parameter, the velocity as well as temperature decreases. At a particular point of the porous stretching sheet, the velocity decreases with the increasing suction parameter. The dimensionless temperature at a point of the sheet decreases due to suction but increases due to injection. The findings of this study reveal that stratification and suction can be used as means of cooling the boundary layer flow region.     

Mixed convection flow of a micropolar fluid over a stretching sheet

The mixed convective flow of a steady, incompressible micropolar fluid over a stretching sheet has been studied. This situation may arise in polymer technology involving the stretching of plastics sheets. The resulting system of non-linear ordinary coupled differential equations has been solved by the finite element method, using the variational Ritz model. Numerical results obtained for velocity, microrotation and temperature distributions are shown graphically. It was found that an increase in the micropolar parameter leads to a faster rate of cooling of the sheet. Also the velocity increases with an increase in micropolar effects. Microrotation effects are much smaller for the no-spin boundary condition as compared to the other boundary condition which assumes that the gyration vector is identical to the angular velocity of the fluid. Received on 9 February 1998     

Effects of partial slip on boundary layer flow past a permeable exponential stretching sheet in presence of thermal radiation

An analysis is presented to describe the boundary layer flow and heat transfer towards a porous exponential stretching sheet. Velocity and thermal slips are considered instead of no-slip conditions at the boundary. Thermal radiation term is incorporated in the temperature equation. Similarity transformations are used to convert the partial differential equations corresponding to the momentum and heat equations into highly non-linear ordinary differential equations. Numerical solutions of these equations are obtained by shooting method. It is found that the fluid velocity and temperature decrease with increasing slip parameter. Temperature is found to decrease with an increase of thermal slip parameter. Thermal radiation enhances the effective thermal diffusivity and the temperature rises.     

On axisymmetric flow of Sisko fluid over a radially stretching sheet

This study presents an analysis of the axisymmetric flow of a non-Newtonian fluid over a radially stretching sheet. The momentum equations for two-dimensional flow are first modeled for Sisko fluid constitutive model, which is a combination of power-law and Newtonian fluids. The general momentum equations are then simplified by invoking the boundary layer analysis. Then a non-linear ordinary differential equation governing the axisymmetric boundary layer flow of Sisko fluid over a radially stretching sheet is obtained by introducing new suitable similarity transformations. The resulting non-linear ordinary differential equation is solved analytically via the homotopy analysis method (HAM). Closed form exact solution is then also obtained for the cases n=0 and 1. Analytical results are presented for the velocity profiles for some values of governing parameters such as power-law index, material parameter and stretching parameter. In addition, the local skin friction coefficient for several sets of the values of physical parameter is tabulated and analyzed. It is shown that the results presented in this study for the axisymmetric flow over a radially non-linear stretching sheet of Sisko fluid are quite general so that the corresponding results for the Newtonian fluid and the power-law fluid can be obtained as two limiting cases.     

具有热源项的驻点流动和传热问题的近似解析解

研究持续拉伸变形表面上二维平面和轴对称驻点流的动量和热量传输问题。利用同伦分析方法获得速度分布和温度分布的级数解,讨论了级数的敛散性。通过图形分析主流速度与拉伸速度的比率参数,普朗特参数,热源参数和流动类型指标对速度边界层和温度边界层的影响。结果表明,这些参数对二维平面驻点流动和传热有较大的影响。     

Heat transfer in stagnation-point flow towards a stretching sheet

 Steady two-dimensional stagnation-point flow of an incompressible viscous fluid over a flat deformable sheet is investigated when the sheet is stretched in its own plane with a velocity proportional to the distance from the stagnation-point. It is shown that for a fluid of small kinematic viscosity, a boundary layer is formed when the stretching velocity is less than the free stream velocity and an inverted boundary layer is formed when the stretching velocity exceeds the free stream velocity. Temperature distribution in the boundary layer is found when the surface is held at constant temperature and surface heat flux is determined. Received on 12 July 2000 / Published online: 29 November 2001     

Effects of the chemical reaction and heat generation or absorption on a mixed convection boundary layer flow over a vertical stretching sheet with nonuniform slot mass transfer

An analysis is performed to study the effects of the chemical reaction and heat generation or absorption on a steady mixed convection boundary layer flow over a vertical stretching sheet with nonuniform slot mass transfer. The governing boundary layer equations with boundary conditions are transformed into the dimensionless form by a group of nonsimilar transformations. Nonsimilar solutions are obtained numerically by solving the coupled nonlinear partial differential equations using the quasi-linearization technique combined with an implicit finite difference scheme. The numerical computations are carried out for different values of dimensionless parameters to display the distributions of the velocity, temperature, concentration, local skin friction coefficient, local Nusselt number, and local Sherwood number. The results obtained indicate that the local Nusselt and Sherwood numbers increase with nonuniform slot suction, but nonuniform slot injection produces the opposite effect. The local Nusselt number decreases with heat generation and increases with heat absorption.     

Effect of viscous dissipation on the mixed convection heat transfer from an exponentially stretching surface

The mixed convection flow and heat transfer from an exponentially stretching vertical surface in a quiescent fluid is analyzed using similarity solution technique. Wall temperature and stretching velocity are assumed to have specific exponential function forms. The influence of buoyancy along with viscous dissipation on the convective transport in the boundary layer region is analyzed in both aiding and opposing flow situations. The flow is governed by the mixed convection parameter Gr/Re². The velocity and temperature inside the boundary layer are observed to be influenced by the parameters like Prandtl number Pr, Gebhart number Gb. Significant changes are observed in non-dimensional skin friction and heat transfer coefficients due to viscous dissipation in the medium. The flow and temperature distributions inside the boundary layer are analyzed and the results for non-dimensional skin friction and heat transfer coefficients are discussed through computer generated plots.     

Scaling Transformations for Boundary Layer Flow near the Stagnation-Point on a Heated Permeable Stretching Surface in a Porous Medium Saturated with a Nanofluid and Heat Generation/Absorption Effects

In this article, a similarity solution of the steady boundary layer flow near the stagnation-point flow on a permeable stretching sheet in a porous medium saturated with a nanofluid and in the presence of internal heat generation/absorption is theoretically studied. The governing partial differential equations with the corresponding boundary conditions are reduced to a set of ordinary differential equations with the appropriate boundary conditions via Lie-group analysis. Copper (Cu) with water as its base fluid has been considered and representative results have been obtained for the nanoparticle volume fraction parameter f{\phi} in the range 0 ￡ f ￡ 0.2{0\leq \phi \leq 0.2} with the Prandtl number of Pr = 6.8 for the water working fluid. Velocity and temperature profiles as well as the skin friction coefficient and the local Nusselt number are determined numerically. The influence of pertinent parameters such as nanofluid volume fraction parameter, the ratio of free stream velocity and stretching velocity parameter, the permeability parameter, suction/blowing parameter, and heat source/sink parameter on the flow and heat transfer characteristics is discussed. Comparisons with published results are also presented. It is shown that the inclusion of a nanoparticle into the base fluid of this problem is capable to change the flow pattern.     

Dual solutions of Casson fluid flows over a power-law stretching sheet

A steady boundary layer flow of a non-Newtonian Casson fluid over a power-law stretching sheet is investigated. A self-similar form of the governing equation is obtained, and numerical solutions are found for various values of the governing parameters. The solutions depend on the fluid material parameter. Dual solutions are obtained for some particular range of these parameters. The fluid velocity is found to decrease as the power-law stretching parameter β in the rheological Casson equation increases. At large values of β, the skin friction coefficient and the velocity profile across the boundary layer for the Casson fluid tend to those for the Newtonian fluid.     

Scaling Transformation for the Effect of Temperature-Dependent Fluid Viscosity with Thermophoresis Particle Deposition on MHD-Free Convective Heat and Mass Transfer Over a Porous Stretching Surface

This article concerns with a steady two-dimensional flow of an electrically conducting incompressible fluid over a vertical stretching sheet. The flow is permeated by a uniform transverse magnetic field. The fluid viscosity is assumed to vary as a linear function of temperature. A scaling group of transformations is applied to the governing equations. The system remains invariant due to some relations among the parameters of the transformations. After finding three absolute invariants, a third-order ordinary differential equation corresponding to the momentum equation, and two second-order ordinary differential equations corresponding to energy and diffusion equations are derived. The equations along with the boundary conditions are solved numerically. It is found that the decrease in the temperature-dependent fluid viscosity makes the velocity to decrease with the increasing distance of the stretching sheet. At a particular point of the sheet, the fluid velocity decreases with the decreasing viscosity but the temperature increases in this case. Impact of thermophoresis particle deposition in the presence of temperature-dependent fluid viscosity plays an important role on the concentration boundary layer. The results, thus, obtained are presented graphically and discussed.     

Oblique stagnation-point flow of an incompressible visco-elastic fluid towards a stretching surface

An analysis is made of the steady two-dimensional stagnation-point flow of an incompressible viscoelastic fluid over a flat deformable surface when the surface is stretched in its own plane with a velocity cx, where x is the distance from the stagnation-point and c is a positive constant. It is shown that for a viscoelastic fluid of short memory (obeying Walters’ B model), a boundary layer is formed when the stretching velocity of the surface is less than ax, where ax+2by is the inviscid free-stream velocity and y is the distance normal to the plate, a and b being constants and the velocity at a point increases with increase in the elasticity of the fluid. On the other hand an inverted boundary layer is formed when the surface stretching velocity exceeds ax and the velocity decreases with increase in the elasticity of the fluid. A novel result of the analysis is that the flow near the stretching surface is that corresponding to an inviscid stagnation-point flow when a=c. Temperature distribution in the boundary layer is found in three cases, namely: (i) the sheet with constant surface temperature (CST); (ii) the sheet with variable surface temperature (VST) and (iii) the sheet with prescribed quadratic power law surface heat flux (PHF) for various values of non-dimensional parameters. It is found that in all the three cases when a/c>1, temperature at a point decreases with increase in the elasticity of the fluid and when a/c<1, temperature at a point increases with increase in the elasticity of the fluid. Further temperature at a point decreases with increase in the radiation parameter and wall temperature parameter.     

Dual solutions of a mixed convection flow near the stagnation point region over an exponentially stretching/shrinking sheet in nanofluids

The aim of this paper is to study the development of mixed convection flow near the stagnation point region over an exponentially stretching/shrinking sheet in nanofluids. The external flow, stretching velocity and wall temperature are assumed to vary as prescribed exponential functions. Using the local similarity method, it has been shown that dual solutions of velocity and temperature exist for certain values of suction/injection, mixed convection, nanoparticle volume fraction and stretching/shrinking parameters. The transformed non-linear ordinary differential equations along with the boundary conditions form a two point boundary value problem and are solved using Shooting method, by converting into an initial value problem. In this method, the system of equations is converted into a set of first order system which is solved by fourth-order Runge–Kutta method. Three different types of nanoparticles, namely copper (Cu), aluminum oxide (Al₂O₃) and titanium oxide (TiO₂) are considered by using water-based fluid with Prandtl number Pr = 6.2. It is also found that the skin friction coefficient and the heat transfer rate at the surface are highest for Copper–water nanofluids as compared to Al₂O₃. The effect of the solid volume fraction parameter φ of the nanofluids on the heat transfer characteristics is also investigated. The results indicate that dual solutions exist only for shrinking sheet. The effects of various parameters on the velocity and temperature profiles are also presented here.