基于涡流发生器的翼型失速流动控制及雷诺数效应影响研究

针对所设计的三角形涡流发生器开展用于翼型失速流动控制的风洞实验研究,重点讨论涡流发生器几何参数、方向角、安装位置及实验雷诺数等因素对翼型失速流动控制的影响。实验结果表明:涡流发生器作用下,在干净翼失速迎角后能够形成一个升力几乎不随迎角变化的相对稳定的高升力状态,抑制了失速流动的发生,与此同时阻力大幅下降;本文所设计的涡流发生器方向角过大时会削弱翼型失速流动控制的效果;同一涡流发生器作用下雷诺数过大其失速流动控制效果会急剧恶化,第一种涡流发生器控制翼型失速的雷诺数有效范围略宽于第二种涡流发生器。     

The onset of dynamic stall revisited

Dynamic stall on a helicopter rotor blade comprises a series of complex aerodynamic phenomena in response to the unsteady change of the blade’s angle of attack. It is accompanied by a lift overshoot and delayed massive flow separation with respect to static stall. The classical hallmark of the dynamic stall phenomenon is the dynamic stall vortex. The flow over an oscillating OA209 airfoil under dynamic stall conditions was investigated by means of unsteady surface pressure measurements and time-resolved particle image velocimetry. The characteristic features of the unsteady flow field were identified and analysed utilising different coherent structure identification methods. An Eulerian and a Lagrangian procedure were adopted to locate the axes of vortices and the edges of Lagrangian coherent structures, respectively; a proper orthogonal decomposition of the velocity field revealed the energetically dominant coherent flow patterns and their temporal evolution. Based on the complementary information obtained by these methods the dynamics and interaction of vortical structures were analysed within a single dynamic stall life cycle leading to a classification of the unsteady flow development into five successive stages: the attached flow stage; the stall development stage; stall onset; the stalled stage; and flow reattachment. The onset of dynamic stall was specified here based on a characteristic mode of the proper orthogonal decomposition of the velocity field. Variations in the flow field topology that accompany the stall onset were verified by the Lagrangian coherent structure analysis. The instantaneous effective unsteadiness was defined as a single representative parameter to describe the influence of the motion parameters. Dynamic stall onset was found to be promoted by increasing unsteadiness. The mechanism that results in the detachment of the dynamic stall vortex from the airfoil was identified as vortex-induced separation caused by strong viscous interactions. Finally, a revised criterion to discern between light and deep dynamic stall was formulated.     

等速上仰翼型分离流动结构的研究

本文通过在翼型上游和翼表面边界层内放置产生氢气泡的铂丝的方法,清楚地显示了上仰翼型分离剪切层的结构。揭示了在不同的翼型转动角速度范围内,存在三种分离流结构。研究了失速涡,剪切涡及起动涡随时间的演变,它们之间的相互作用和转动角速度等参数的影响,分离剪切层的流动显示结果,结合翼型上气动力与流场中涡量矩的关系的理论,定性地解释了上仰翼型产生非定常高升力的原因。     

风力机翼型动态失速等离子体流动控制数值研究

针对动态失速引起的风力机翼型气动性能恶化的问题,本文基于动网格和滑移网格技术, 开展了大涡模拟数值计算研究,探索了非定常脉冲等离子体的动态流动控制机理. 结果表明,等离子体气动激励能够有效控制翼型动态失速, 改善平均和瞬态气动力,减小力矩负峰值和迟滞环面积. 压力分布在等离子体施加范围内出现了负压"凸起",上翼面吸力峰值明显增大.脉冲频率和占空比这两个非定常控制参数对流动控制影响显著,无因次脉冲频率为1.5时等离子体控制效果较好,占空比为0.8时即可接近连续工作模式下的气动收益. 翼型深失速状态,等离子体促使流动分离位置明显向后缘移动, 抵抗了大尺度动态失速涡的发生,分离涡结构破碎耗散、重新附着, 涡流影响范围减小; 浅失速状态,等离子体激励具有较强的剪切层操纵能力, 诱导了翼型边界层提前转捩,促进了与主流的动量掺混. 等离子体气动激励诱导出前缘附近贴体翼面"涡簇",起到了虚拟气动外形的作用.不同尺度、频域的动态涡结构与等离子体气动激励的非线性、强耦合作用导致了气动力/力矩的谐波振荡.      

NUMERICAL STUDY ON DYNAMIC STALL FLOW CONTROL FOR WIND TURBINE AIRFOIL USING PLASMA ACTUATOR 1)

针对动态失速引起的风力机翼型气动性能恶化的问题,本文基于动网格和滑移网格技术, 开展了大涡模拟数值计算研究,探索了非定常脉冲等离子体的动态流动控制机理. 结果表明,等离子体气动激励能够有效控制翼型动态失速, 改善平均和瞬态气动力,减小力矩负峰值和迟滞环面积. 压力分布在等离子体施加范围内出现了负压"凸起",上翼面吸力峰值明显增大.脉冲频率和占空比这两个非定常控制参数对流动控制影响显著,无因次脉冲频率为1.5时等离子体控制效果较好,占空比为0.8时即可接近连续工作模式下的气动收益. 翼型深失速状态,等离子体促使流动分离位置明显向后缘移动, 抵抗了大尺度动态失速涡的发生,分离涡结构破碎耗散、重新附着, 涡流影响范围减小; 浅失速状态,等离子体激励具有较强的剪切层操纵能力, 诱导了翼型边界层提前转捩,促进了与主流的动量掺混. 等离子体气动激励诱导出前缘附近贴体翼面"涡簇",起到了虚拟气动外形的作用.不同尺度、频域的动态涡结构与等离子体气动激励的非线性、强耦合作用导致了气动力/力矩的谐波振荡.     

等速上仰翼型尾部流动观察及动态失速机理探讨

在尾缘处置氢气泡铂丝,观察了上仰翼型自尾缘流入尾迹的涡层。基于尾涡层及(以往)上翼面分离涡的观察,用涡动力学理论,探讨了动态失速的机理,并解释了新的失速现象。     

旋翼翼型动态失速流场特性PIV试验研究及L-B模型修正

为测量翼型动态失速的非定常涡流场特性,采用3D-PIV 技术,对典型直升机旋翼翼型SC1095 的动态失速流场特性进行测量,发现涡在不同位置处的输运速度不同:位于翼型表面的涡的无量纲速度为0.39,位于尾迹区的涡的无量纲速度为0.55. 利用前缘涡输运速度变化这一特征,改进了经典的翼型动态失速利什曼-贝多斯（Leishman-Beddoes,L-B）模型,将该模型中固定的涡时间常数修正为可以随涡位置变化的时变函数,修正后的模型计算得到翼型法向力峰值相对原L-B 模型提升5%,力矩系数负峰值相对原L-B 模型提升13%,与试验值相比更加吻合,表明修正后的翼型动态失速模型更好地体现了翼型前缘涡的物理特征.      

Numerical investigation of dynamic stall of an oscillating aerofoil

The flow structure around an NACA 0012 aerofoil oscillating in pitch around the quarter-chord is numerically investigated by solving the two-dimensional compressible N–S equations using a special matrix-splitting scheme. This scheme is of second-order accuracy in time and space and is computationally more efficient than the conventional flux-splitting scheme. A ‘rigid’ C-grid with 149 × 51 points is used for the computation of unsteady flow. The freestream Mach number varies from 0.2 to 06 and the Reynolds number from 5000 to 20,000. The reduced frequency equals 0.25–0.5. The basic flow structure of dynamic stall is described and the Reynolds number effect on dynamic stall is briefly discussed. The influence of the compressibility on dynamic stall is analysed in detail. Numerical results show that there is a significant influence of the compressibility on the formation and convection of the dynamic stall vortex. There is a certain influence of the Reynolds number on the flow structure. The average convection velocity of the dynamic stall vortex is approximately 0.348 times the freestream velocity.     

PIV EXPERIMENTS ON FLOWFIELD CHARACTERISTICS OF ROTOR AIRFOIL DYNAMIC STALL AND MODIFICATIONS OF L-B MODEL

为测量翼型动态失速的非定常涡流场特性,采用3D-PIV 技术,对典型直升机旋翼翼型SC1095 的动态失速流场特性进行测量,发现涡在不同位置处的输运速度不同：位于翼型表面的涡的无量纲速度为0.39,位于尾迹区的涡的无量纲速度为0.55. 利用前缘涡输运速度变化这一特征,改进了经典的翼型动态失速利什曼-贝多斯（Leishman-Beddoes,L-B）模型,将该模型中固定的涡时间常数修正为可以随涡位置变化的时变函数,修正后的模型计算得到翼型法向力峰值相对原L-B 模型提升5%,力矩系数负峰值相对原L-B 模型提升13%,与试验值相比更加吻合,表明修正后的翼型动态失速模型更好地体现了翼型前缘涡的物理特征.     

Influence of pitching angle of incidence on the dynamic stall behavior of a symmetric airfoil

This study presents the influence of pitch angle of an airfoil on its near-field vortex structure as well as the aerodynamic loads during a dynamic stall process. Dynamic stall behavior in a sinusoidally pitching airfoil is usually analyzed at low to medium reduced frequencies and with the maximum angle of attack of the airfoil not exceeding 25°. In this work, we study dynamic stall of a symmetric airfoil at medium to high reduced frequencies even as the maximum angle of attack goes from 25° to 45°. The evolution and growth of the laminar separation bubble, also known as a dynamic stall vortex, at the leading edge and the trailing edge are studied as the pitch cycle goes from the minimum to the maximum angle of attack. The effect of reduced frequencies on the vortex structure as well as the aerodynamic load coefficients is investigated. The reduced frequency is shown to be a bifurcation parameter triggering period doubling behavior. However, the bifurcation pattern is dependent on the variation of the pitch angle of incidence of the airfoil.     

Assessment of 2D/3D numerical modeling for deep dynamic stall experiments

The results of computational fluid dynamics (CFD) simulations in two and three spatial dimensions are compared to pressure measurements and particle image velocimetry (PIV) flow surveys to assess the suitability of numerical models for the simulation of deep dynamic stall experiments carried out on a pitching NACA 23012 airfoil. A sinusoidal pitching motion with a 10° amplitude and a reduced frequency of 0.1 is imposed around two different mean angles of attack of 10° and 15°. The comparison of the airloads curves and of the pressure distribution over the airfoil surface shows that a three-dimensional numerical model can better reproduce the flow structures and the airfoil performance for the deep dynamic stall regime. Also, the vortical structures observed by PIV in the flow field are better captured by the three-dimensional model. This feature highlighted the relevance of three-dimensional effects on the flow field in deep dynamic stall.     

Investigation of the unsteady flow velocity field above an airfoil pitching under deep dynamic stall conditions

The unsteady flow field above a NACA 0012 airfoil pitching under deep dynamic stall conditions has been investigated in a low-speed wind tunnel by means of particle image velocimetry. The measurements of the instantaneous flow velocity field show the characteristic features of the dynamic stall process: formation and development of an organized vortex structure for increasing incidences and the subsequent separation. Vorticity and divergence estimated from the measured data give a good insight into the complex flow behaviour during the downstroke motion. Furthermore, small-scale structures could be observed in the separated flow field and even within the dynamic stall vortex.The authors would like to thank Dr. Schäfer (ISL) for his support in organizing the cooperative measurements, Mr. Seyb (DLR) for his help during the recording of PIV images, Dr. Bretthauer (DLR) and Mr. Vollmers (DLR) for his assistance during the phase of evaluation and post processing of the PIV recordings and Dr. Geißler (DLR) for helpful discussions on the dynamic stall problem.     

A phase-locked high-speed real-time interferometry system for large amplitude unsteady flows

A high-speed phase-locked interferometry system has been designed and developed for real-time measurements of dynamic stall flow over a pitching airfoil. Point diffraction interferograms of incipient flow separation over a sinusoidally oscillating airfoil have been obtained at framing rates of up to 20 kHz and for free stream Mach numbers of 0.3 and 0.45. The images were recorded on 35 mm ASA 125 and ASA 400 films using a drum camera. Special electronic timing and synchronizing circuits were developed to trigger the laser light source from the camera and to initiate acquisition of the interferogram sequence from any desired phase angle of oscillation. The airfoil instantaneous angle of attack data provided by an optical encoder was recorded via a FIFO data buffer into a microcomputer. The interferograms have been analyzed using software developed in-house to get quantitative flow density and pressure distributions.Mr. N.J. Brock and Mr. B.J. Weber of Aerometrics. Inc. in preparing the laser specifications are gratefully acknowledged.The project was supported by US Air Force Office of Scientific Research through grants, AFOSR-ISSA-89-0067 and AFOSR-MIPR-92-0004. Additional support was received from the Army Research Office grant ARO-MIPR-125-93. The support and encouragement of Dr. S.S. Davis, Chief, Fluid Mechanics Laboratory Branch and the help provided by     

Lift enhancement of airfoil and tip flow control for wind turbine

Two techniques that improve the aerodynamic performance of wind turbine airfoils are described. The airfoil S809, designed specially for wind turbine blades, and the airfoil FX60-100, having a higher lift-drag ratio, are selected to verify the flow control techniques. The flow deflector, fixed at the leading edge, is employed to control the boundary layer separation on the airfoil at a high angle of attack. The multi-island genetic algorithm is used to optimize the parameters of the flow deflector. The results indicate that the flow deflector can suppress the flow separation, delay the stall, and enhance the lift. The characteristics of the blade tip vortex, the wake vortex, and the surface pressure distributions of the blades are analyzed. The vortex diffuser, set up at the blade tip, is employed to control the blade tip vortex. The results show that the vortex diffuser can increase the total pressure coefficient of the core of the vortex, decrease the strength of the blade tip vortex, lower the noise, and improve the efficiency of the blade.     

等速上仰翼型动态失速现象研究

翼型大迎角绕流的静态失速将造成升力突降和气动性能急剧恶化，但利用非定常运动所产生 的动态失速效应，可以大大地延缓气流分离和失速现象的发生. 采用Rogers发 展的双时间步Roe格式，求解拟压缩性修正不可压N-S方程. 数值模拟了低雷诺数 ($Re=4.8 \times 10^{4}$)条件下NACA0015翼型作等速上仰($\alpha =0^{\circ} \sim 60^{\circ}$)的动态失速过程，同Walker的试验结果比 较，验证了计算结果的正确性. 研究了该过程中主涡、二次涡和三次涡的发展，升 力系数随攻角变化，以及不同上仰速度对动态失速效应所造成的影响.     

High-fidelity simulations of moving and flexible airfoils at low Reynolds numbers

The present paper highlights results derived from the application of a high-fidelity simulation technique to the analysis of low-Reynolds-number transitional flows over moving and flexible canonical configurations motivated by small natural and man-made flyers. This effort addresses three separate fluid dynamic phenomena relevant to small fliers, including: laminar separation and transition over a stationary airfoil, transition effects on the dynamic stall vortex generated by a plunging airfoil, and the effect of flexibility on the flow structure above a membrane airfoil. The specific cases were also selected to permit comparison with available experimental measurements. First, the process of transition on a stationary SD7003 airfoil section over a range of Reynolds numbers and angles of attack is considered. Prior to stall, the flow exhibits a separated shear layer which rolls up into spanwise vortices. These vortices subsequently undergo spanwise instabilities, and ultimately breakdown into fine-scale turbulent structures as the boundary layer reattaches to the airfoil surface. In a time-averaged sense, the flow displays a closed laminar separation bubble which moves upstream and contracts in size with increasing angle of attack for a fixed Reynolds number. For a fixed angle of attack, as the Reynolds number decreases, the laminar separation bubble grows in vertical extent producing a significant increase in drag. For the lowest Reynolds number considered (Re _c  = 10⁴), transition does not occur over the airfoil at moderate angles of attack prior to stall. Next, the impact of a prescribed high-frequency small-amplitude plunging motion on the transitional flow over the SD7003 airfoil is investigated. The motion-induced high angle of attack results in unsteady separation in the leading edge and in the formation of dynamic-stall-like vortices which convect downstream close to the airfoil. At the lowest value of Reynolds number (Re _c  = 10⁴), transition effects are observed to be minor and the dynamic stall vortex system remains fairly coherent. For Re _c  = 4 × 10⁴, the dynamic-stall vortex system is laminar at is inception, however shortly afterwards, it experiences an abrupt breakdown associated with the onset of spanwise instability effects. The computed phased-averaged structures for both values of Reynolds number are found to be in good agreement with the experimental data. Finally, the effect of structural compliance on the unsteady flow past a membrane airfoil is investigated. The membrane deformation results in mean camber and large fluctuations which improve aerodynamic performance. Larger values of lift and a delay in stall are achieved relative to a rigid airfoil configuration. For Re _c = 4.85 × 10⁴, it is shown that correct prediction of the transitional process is critical to capturing the proper membrane structural response.     

Dynamics of co-rotating vortices in a flow around a bio-inspired corrugated airfoil

Bio-inspired corrugated airfoils show favourable aerodynamic characteristics such as high coefficient of lift and delayed stall at low Reynolds numbers. Two-dimensional (2D) direct numerical simulation has been performed here on a corrugated airfoil at various angles of attack (0°, +5°, -5°) and Reynolds number of 280 to 6700. The objective is to analyse the pressure variation inside the corrugations and correlate it to the vortex movement across the corrugations and the overall aerodynamic characteristics of the corrugated airfoil. The flow characteristics have been examined based on the local Strouhal numbers in the corrugations of the airfoil. It is observed that the pressure variation in each corrugation is the result of vortex merging and separation in the corrugation which plays a major role in changing the flow characteristics. The Strouhal number of the flow is dictated by the most dominant local Strouhal number. The numerical results are further compared with experimental results obtained using particle image velocimetry, and the two set of results are found to match well. These results are significant because they elucidate the effect of corrugation, angle of attack, and Reynolds number on flow over a corrugated airfoil.     

On the unsteady motion and stability of a heaving airfoil in ground effect

This study explores the fluid mechanics and force generation capabilities of an inverted heaving airfoil placed close to a moving ground using a URANS solver with the Spalart-Allmaras turbulence model. By varying the mean ground clearance and motion frequency of the airfoil, it was possible to construct a frequency-height diagram of the various forces acting on the airfoil. The ground was found to enhance the downforce and reduce the drag with respect to freestream. The unsteady motion induces hysteresis in the forces’ behaviour. At moderate ground clearance, the hysteresis increases with frequency and the airfoil loses energy to the flow, resulting in a stabilizing motion. By analogy with a pitching motion, the airfoil stalls in close proximity to the ground. At low frequencies, the motion is unstable and could lead to stall flutter. A stall flutter analysis was undertaken. At higher frequencies, inviscid effects overcome the large separation and the motion becomes stable. Forced trailing edge vortex shedding appears at high frequencies. The shedding mechanism seems to be independent of ground proximity. However, the wake is altered at low heights as a result of an interaction between the vortices and the ground.     

风力机叶片翼型动态试验技术研究

风力机叶片动态振荡过程往往伴随着俯仰和横摆同时进行, 以前对许多动态问题不清楚的阶段, 工程上不惜以增加叶片重量为代价而采用偏安全的设计, 通常忽略横摆振荡的影响; 大型风力机设计对获取翼型更加全面、准确的动态载荷提出了更高要求, 研究横摆振荡对翼型动态气动特性的影响规律具有重要意义. 本文首次开展翼型横摆振荡动态风洞试验研究, 采用“电子凸轮”技术代替机械凸轮实现了振荡频率和振荡角度的无级变化, 基于设计的电子外触发装置实现了对动态流场的实时测量, 实现了风洞来流、模型角位移和动态压力数据的同步采集, 分别开展了翼型静态测压、俯仰/横摆动态测压、粒子图像测速和荧光丝线等试验研究, 试验结果准度较高、规律合理; 分析了动态试验洞壁干扰影响机制. 研究表明, 横摆振荡翼型的气动曲线也存在明显迟滞效应; 随着振荡频率升高, 翼型俯仰和横摆振荡下的气动迟滞性均增强; 翼型俯仰振荡正行程的动态失速涡破裂有所延迟; 洞壁与模型端部交界处的强三维效应对翼型压力分布影响较大; 建立的横摆振荡试验技术可为风力机动态掠效应的研究提供技术支撑.      

The physics of modeling unsteady flaps with gaps

Research indicates that active control concepts have promise in mitigating numerous adverse phenomena associated with the aeromechanics of lifting surfaces. These techniques are being applied to delay stall of fixed wing aircraft, as well as to eliminate or mitigate vibratory loads, blade–vortex interaction, and dynamic stall of the flow about rotorcraft and wind turbine blades. These phenomena are nonlinear and unsteady for dynamic systems, which add yet another layer of complexity on the physics of the flow. While a plethora of different active control techniques is being explored, the use of trailing edge flaps appears to be one of the more viable and cost-effective concepts. Static multi-element airfoils and wings have been analyzed computationally, but little exists on the ability to model these when the airfoil and flap are dynamic. The costs associated with modeling the gap between the airfoil and flap have led to approximations where the flap is modeled only as a morphed tip of the airfoil (no gap). Using a hybrid Reynolds-Averaged Navier–Stokes/Large-Eddy-Simulation turbulence technique, an oscillating flapped airfoil has been studied to determine the influence of modeling the gap on the performance and acoustic signature of the airfoil. Results are compared with the experimental data to confirm the validity of the computational approach. Both attached and separated (dynamic stall) oscillating flows are examined. The physics within the gap are found to be important for the airfoil performance when stall is encountered, as well as when acoustic signatures are required.