Catalytic Performance in CO Hydrogenation Over SiO_2-Supported Ru-M (M=Co, Fe,Mo,Ni,Rh,Mn and Cr) Bimetallic Cluster-derived Catalysts

The bimetallic Ru-M (M=Co,Fe,Ni,Mo, Rh,Cr, Mn) catalysts were prepared from SiO_2-supported bimetallic carbonyl clusters, and it was found that the Ru-Co, Ru-Fe and Ru-Mo bimetallic carbonyl cluster-derived catalysts showed higher activity and selectivity for oxygenates such as C_1-C_5 alcohols in CO hydrogenation,in contrast to catalysts prepared from SiO_2-supported homometallic Ru and Co carbonyl clusters. In situ FT-IR studies revealed that the bands at 1584 and 1555 cm~(-1) species were intermediates to produce methanol and higher oxygenates,and at higher temperatures the 1584 cm~(-1) species could react with alkyl to form 1555 cm~(-1) species. By the surface chemical reaction and the IR study of isotopic molecules,it was suggested that 1584 and 1555 cm~(-1) were assigned to surface formyl and acetyl species.     

Activity and Selectivity in CO Hydrogenation with Silica-supported Ru-Co Bimetallic Cluster-derived Catalysts

The catalytic performance of bimetallic Ru-Co catalysts prepared from a series of H3Ru3Co(CO)12. RuCo2(CO)11 and HRuCo3(CO)12 in CO hydrogenation was investigated, and it was found that the Ru-Co bimetallic carbonyl cluster-derived catalysts showed a high activity for products, particularly higher oxygenates, compared with the catalysts prepared from impregnation or co-impregnation of monometallic clusters such as [HRu3(CO)11] and Co4(CO)12. The selectivity for oxygenates in CO hydrogenation highly increased with the molar ratio of Co/Ru in the Ru-Co bimetallic cluster to CO/H2 in feed gas. Raising reaction temperature led to an intensive increase of CO conversion and a considerable decrease of selectivity for oxygenates. In situ FT-IR studies revealed that the band at 1584 cm-1 on Ru-Co bimetallic cluster-derived catalysts at 453 K under syngas (CO/H2 = 0. 5) has a good linear relationship to rates of oxygenate formation, which is likely associated with an intermediate to produce oxygenates in CO hydro     

RuCo催化剂CO加氢形成含氧物的中间体：甲酰基

进行了在SiO_2担载的Ru-Co双金属原子簇催化剂上合成气(CO+H_2)反应和模型化合物吸附的红外、质谱研究. 结果表明, 在原子簇制备的Ru-Co/SiO_2催化剂上, 在453 K下合成气(CO+H_2)反应在红外谱图产生了1584 cm~(-1)谱带, 它与CO加氢反应中含氧化台物的生成速率成线性关系. 因此提出了此谱峰对应着在CO加氢反应中生成古氧化合物的一个十分重要的中间体. 以CO+D_2、~(13)CO+H_2和~(13)CO+D_2代替CO+H_2, 在Ru-Co/SiO_2催化剂中, 1584 cm~(-1)谱带分别位移至1575、1542和1539 cm~(-1)处. 还观察到, 1584 cm~(-1)物种与H_2反应, 产物给出了CH_4和CH_3OH; 如果1584 cm~(-1)物种和D_2反应则生成CHD_3和CHD_2OD. 这些结果提出了1584 cm~(-1)谱带归属于表面甲酰基的羰基振动, 这同Ru-Co/SiO_2催化剂吸附甲醛的结果基本一致.     

Ni-Co、Ni-Cu双金属合金催化剂用于CO甲烷化

以钙钛矿型复合氧化物LaNi_0.9Co_0.1O₃和LaNi_0.9Cu_0.1O₃为前驱体制备了Ni-Co/La₂O₃和Ni-Cu/La₂O₃双金属合金催化剂。结果表明,双金属合金催化剂中,各组分间相互稀释,具有较强的抗烧结性能;催化剂表面的积炭主要取决于CO在催化剂表面的吸附形态,Ni-Co双金属催化剂中,Co掺杂改变了CO在催化剂表面的吸附形式和吸附强度,使得Ni-Co双金属催化剂具有较强的抗积炭性能。Ni-Co双金属合金催化剂用于CO甲烷化反应时,显现出较好的活性、选择性和稳定性。     

Ni-Fe/γ-Al2O3双金属催化剂的制备及其CO甲烷化性能研究

采用等体积浸渍法制备了Ni-Fe/γ-Al₂O₃双金属催化剂和Ni/γ-Al₂O₃、Fe/γ-Al₂O₃单金属催化剂,在连续流动微反装置上考察了催化剂的CO甲烷化催化活性,采用XRD、N₂物理吸附、H₂-TPR、H₂-TPD和TPSR等手段对催化剂进行表征。结果表明,Ni-Fe/γ-Al₂O₃双金属催化剂中Ni、Fe之间产生了明显的相互作用,还原后催化剂中形成Ni-Fe合金,对氢气吸附量显著增加。在CO体积分数为0.5%、空速5000h^-1、常压的反应条件下,Ni-Fe/γ-Al₂O₃双金属催化剂表现出高的甲烷化活性,220℃时将CO完全转化为甲烷。     

Synthesis and characterization of niobium-promoted cobalt/iron catalysts supported on carbon nanotubes for the hydrogenation of carbon monoxide

Bimetallic Co /Fe catalysts supported on carbon nanotubes( CNTs) were prepared,and niobium( Nb) was added as promoter to the 70 Co ∶30Fe /CNT catalyst. The physicochemical properties of the catalysts were characterized,and the catalytic performances were analyzed at the same operation conditions( H_2 ∶CO( volume ratio) = 2 ∶1,p = 1 MPa,and t = 260 ℃) in a tubular fixed-bed microreactor system. The addition of Nb to the bimetallic catalyst decreases the average size of the oxide nanoparticles and improves the reducibility of the bimetallic catalyst. Evaluation of the catalyst performance in a Fischer-Tropsch reaction shows that the catalyst results in high selectivity to methane,and the selectivity to C_(5+) increased slightly in the bimetallic catalyst unlike that in the monometallic catalysts. The addition of 1% Nb to the bimetallic catalyst increases CO conversion and selectivity to C_(5+). Meanwhile,a decrease in methane selectivity is observed.     

Cu-Co负载量对Cu-Co基催化剂催化CH4-合成气梯阶转化合成C2+含氧化合物的影响

以TiO₂纳米粒子为载体, 采用等体积浸渍法制备了Cu-Co双金属催化剂, 考察了不同Cu/Co质量比和不同Cu-Co含量的双金属催化剂对CH₄-合成气梯阶转化直接合成C₂⁺含氧化合物的影响. 在连续式步阶固定床反应装置上进行了催化性能评价. 实验结果表明, 当Cu-Co含量为18%, Cu/Co质量比为2: 1时, Cu-Co/TiO₂的C₂⁺含氧化合物产物的时空收率最大, 为19.92 mg·g_cat^-1·h^-1, 选择性为67.76%. 研究表明, 金属组分之间和载体与金属组分之间的相互作用、 金属组分良好的分散性和还原性是促进活性位的形成和提高催化剂活性的原因; 催化剂表面高度分散的CuO微晶有利于催化加氢和脱氢反应的进行, 对CH₄-合成气转化反应有重要的促进作用. 另外, 弱酸和中强酸有利于CH₄-合成气转化反应, 而强酸对该反应有抑制作用.     

以钙钛矿型复合氧化物为前驱体构筑La-Ce氧化物修饰的Pt-Co纳米双金属催化剂及其对CO氧化的性能

利用钙钛矿型复合氧化物(PTO)可以将多种金属离子限域并均匀混合于钙钛矿晶格中的特点,提出了一种构筑氧化物修饰的纳米双金属催化剂团簇的新构想。以担载于大比表面积SiO_2上的钙钛矿型复合氧化物La_(1-y)Ce_yCo_(0.87)Pt_(0.13)O_3/SiO_2作为前驱体,将La、Ce、Co和Pt多种金属离子均匀混合并限域于PTO晶粒中,还原后得到Pt-Co/La-Ce-O/SiO_2催化剂;通过氮气吸附-脱附、XRD、H2-TPR和TEM等手段对Pt-Co/La-Ce-O/SiO_2催化剂进行了表征,考察了其对CO氧化的催化性能,研究了构效关系。结果发现,La-Ce-O-Pt-Co构成了纳米团簇,担载于SiO_2表面,形成了Pt-Co纳米双金属颗粒; Co修饰Pt提高了其催化活性,而添加Ce进一步改善了其催化性能。当Ce含量(y)为0.2时,催化剂La_(0.8)Ce_(0.2)Co_(0.87)Pt_(0.13)O_3/SiO_2的活性最佳,在120℃下即可实现CO完全转化,且在含体积分数15%H_2O及12.5%CO_2的气氛中仍具有较好的催化性能。稳定性测试表明,所制得的Pt-Co/La-Ce-O/SiO_2催化剂具有良好的稳定性和抗烧结性能。     

Rh-Mn-Li/SiO2催化剂上CO加氢制C2含氧化合物:载体硅烷化程度的影响

以三甲基氯硅烷为硅烷化试剂,对硅胶进行不同程度硅烷化预处理,采用浸渍法制备了其负载的Rh-Mn-Li催化剂,用于CO加氢制C₂含氧化合物的反应,并运用红外光谱、N₂吸附-脱附法、C含量测定、透射电镜、H₂程序升温还原和程序升温表面反应等手段对载体和催化剂进行了表征。结果表明,制得的不同硅烷化程度硅胶织构性质变化不大,它们负载的催化剂上Rh平均粒径均在3nm左右,硅烷化对催化剂吸附CO的形态和Rh的还原性能的影响均很小,但随着载体硅烷化程度的提高,催化剂上Rh解离CO的能力增加,因而其活性逐渐增加,且不影响C₂含氧化合物的选择性。     

La2O3助剂对Rh/SiO2催化CO加氢反应性能的影响

采用溶胶凝胶法制备了SiO_2和La_2O_3-SiO_2载体,再通过浸渍法分别引入Rh-La和Rh组分,研究考察了La引入方式对Rh/SiO_2催化CO加氢反应性能的影响。结果表明,La的添加有利于提高Rh的分散度,促进Rh+中心数的增加,有效地抑制产物中CO2的生成,提高含氧化合物选择性。此外,La的引入方式会影响La与Rh间的相互作用强弱,Rh和La共浸渍制得的2Rh-5La_2O_3/SiO_2催化剂中Rh-La相互作用较强,削弱的Rh-CO键有利于反应过程中CO的插入反应,使得产物以C_(2+)含氧化合物为主。而La以助剂形式掺入SiO_2制得的2Rh/5La_2O_3-SiO_2催化剂具有较弱的La-Rh相互作用,其产物则以甲醇、乙醇等低碳醇为主。     

高温沉淀铁基催化剂上费托合成含氧化合物生成机理的研究

采用漫反射原位红外光谱法及化学捕获方法,考察了费托合成过程中高温沉淀铁基催化剂表面吸附物种的变化,并探讨了含氧化合物的生成机理。结果表明,CO在高温沉淀铁基催化剂上有线式和桥式两种吸附态存在,同时,CO的吸附在催化剂表面生成大量含氧化合物前驱体。费托原位实验捕获到了一些较关键的中间产物:表面乙酸盐、表面酰基、甲氧基等。同时发现高温沉淀铁基催化剂表面具有以下反应共性:醇类可与表面羟基结合生成烷氧基团;催化剂表面的吸附分子具有氧化性;一些基础化学物质如OH^-、晶格氧等可以与甲醇或乙醛分子发生反应。对CH₃OH + CO及CH₃I + CO + H₂两个反应的化学捕获实验表明,酰基是C₂⁺含氧化合物的重要中间产物,酰基加氢是形成C₂⁺含氧化合物的关键步骤。根据表面中间产物及反应特性,得到了高温沉淀铁基催化剂上费托合成含氧化合物的生成机理。     

凹凸棒石负载Cu-Fe-Co基催化剂组合体系用于CO加氢制备低碳醇

采用浸渍法(IM)和浸渍燃烧法(IMSC)制备了凹凸棒石(ATP)及凹凸棒石-多孔硅胶微球混合物(ATPS)负载CuFe-Co基改性费托催化剂,通过N_2吸附-脱附、X射线衍射(XRD)、X射线光电子能谱(XPS)、扫描电镜(SEM)、透射电镜(TEM)、H_2-程序升温还原(H_2-TPR)和CO_2-程序升温脱附(CO_2-TPD)等手段对催化剂进行了表征,并将它们应用于CO加氢制备低碳醇反应。结果表明,IMSC较IM制备催化剂更有利于CuO的负载、分散和还原,促进H_2和CO与Cu活性位的接触,但两者的最佳低碳醇合成温度均为280℃。通过对ATP和ATPS负载Cu-Fe-Co基催化剂(CFCK/ATP、CFCK/ATPS)与Cu/ZnO/Al_2O_3(CZA)甲醇催化剂的组合体系的优化,获得较理想的低碳醇合成催化剂组合体系CZA║CFCK/ATPS-IMSC。利用它们之间的"产物转化耦合效应",实现CO转化率为46.3%,低碳醇选择性为39.6%,C_(2+)醇含量为22.7%。     

负载型双金属催化剂的制备及其等离子体催化氨分解制氢性能

利用等体积浸渍法制备了Fe-Co、Fe-Ni、Mo-Co、Mo-Ni双金属催化剂(总金属含量均为10%(w,质量分数),双金属摩尔比均为1:1),考察了其在等离子体条件下氨分解活性,结果表明Fe-Ni双金属催化剂表现出较好的协同作用。在此基础上,进一步考察了Fe/Ni摩尔比对其活性的影响。结果表明:当Fe/Ni摩尔比为6/4时,氨分解活性最好,而且该双金属催化剂稳定性良好。采用N_2物理吸附、X射线衍射(XRD)、H_2-程序升温还原(H_2-TPR)和高分辨透射电子显微镜(HRTEM)对催化剂的物化性质、还原性能、微观形貌等进行了研究。结果表明:活性较好的Fe-Ni双金属催化剂中,Fe与Ni形成尖晶石结构NiFe_2O_4,该结构有利于Fe和Ni的还原,即活性组分易恢复金属态,这可能是其活性较高的原因。     

EXAFS/FT-IR characterization of tetra-iridium carbonyl clusters bound to tris-(hydroxymethyl)phosphine grafted silica surface catalytically active for propene oxidation to acetone

Structure and catalytic activity of Ir₄(CO)₁₂ bound to tris-(hydroxymethyl)phosphine (THP) grafted silica (THP/SiO₂) was investigated by means of EXAFS, FT-IR and kinetic studies. It was found that Ir₄(CO)₁₂ was uniformly attached on THP/SiO₂ by substitution of CO by THP (Ir₄/THP/SiO₂). The tetra-iridium carbonyl cluster framework was remained during the substitution of THP ligands and two THP ligands coordinated to the iridium carbonyl clusters to form Ir₄(CO)₁₀(THP/SiO₂)₂. species. When Ir₄/THP/SiO₂ was evacuated at 373 K, bridge CO was desorbed and Debye-Waller factor of Ir---Ir contribution derived from EXAFS analysis was increased which suggested that the cluster framework was distorted by the evacuation at 373 K. The resulting sample evacuated at 373 K was an active catalyst for hydroformylation of ethene and partial oxidation of propene, while the Ir₄/THP/SiO₂ without evacuation exhibited poor catalytic activities. The propene oxidation reaction proceed on the Ir₄/THP/SiO₂ evacuated at 323–353 K under subatmospheric pressures to give acetone as a product in high selectivity. The ethene hydroformylation proceed on the evacuated Ir₄/THP/SiO₂ at lower temperatures compared with other conventional iridium catalysts. EXAFS characterization and kinetic studies suggested that the catalytic activities were associated with the structural distortion of the iridium cluster framework due to surface attachment by the bidentate phosphine substitution.     

Supported bimetallic catalyst Pt-Pb/SiO2 for selective conversion of nitrobenzene to p-aminophenol in pressurized CO2/H2O system

Various supported Pt-Pb bimetallic catalysts were prepared and applied for the catalytic conversion of nitrobenzene to p-aminophenol in the environmentally benign pressurized CO_2/H_2O system.Among the bimetallic catalysts prepared,Pt-Pb/SiO_2 is the best and nitrobenzene could be converted to paminophenol with a selectivity as high as 82% when the reaction was carried out using this catalyst at110 ℃ under 5 MPa CO_2 and 0.2 MPa H_2.     

金属助剂对Ni/SiO2催化剂苯甲醚加氢脱氧性能的影响

采用等体积浸渍法制备了Ni/SiO₂及Ni与金属助剂M（M=Fe、Co、Cu、Zn及Ga）物质的量比为30的Ni基双金属催化剂（记作Ni₃₀M/SiO₂）,利用H₂-TPR、XRD、H₂化学吸附、NH₃-TPD以及N₂物理吸附-脱附等手段对催化剂进行了结构表征,研究了不同助剂对催化剂结构与苯甲醚加氢脱氧性能影响。结果发现,金属助剂影响了催化剂前驱体中镍物种的还原性能,表明金属助剂及镍之间存在一定相互作用。Ni₃₀M/SiO₂中Ni-M双金属晶粒粒径和Ni/SiO₂中金属Ni晶粒粒径相近。由于表面张力较低的金属会在双金属晶粒表面富集,Ni₃₀M/SiO₂的H₂化学吸附量不同程度地低于Ni/SiO₂。另外,Ni₃₀M/SiO₂催化剂的酸量（尤其较弱酸中心酸量）高于Ni/SiO₂。在300℃、常压、苯甲醚质量空速1.0 h^-1及H₂与苯甲醚物质的量比为25：1条件下考察了各催化剂苯甲醚的加氢脱氧性能。Ni₃₀M/SiO₂上苯甲醚转化率不同程度低于Ni/SiO₂,原因在于Ni₃₀M/SiO₂催化剂H₂化学吸附量较低。Ga及Zn改性催化剂上三苯（包括苯、甲苯及二甲苯）选择性分别为81.7%和76.8%,高于Ni/SiO₂（71.5%）,且Ni₃₀Ga/SiO₂及Ni₃₀Zn/SiO₂上三苯收率（分别为65.0%及63.8%）高于或接近于Ni/SiO₂（63.7%）。Ni/SiO₂及Ni₃₀M/SiO₂催化剂中,Ni₃₀Zn/SiO₂具有较高甲基转移能力及较低C-C键氢解活性。从提高碳收率、降低耗氢量角度而言,Ni₃₀Zn/SiO₂具有较佳的加氢脱氧性能,与Ni和Zn之间作用及Zn亲氧性高于Ni有关。     

水热法Fe-Mn催化剂制备及其合成气制低碳烯烃催化活性

以水热合成法制备了K原位改性的Fe-Mn催化剂,考察了其CO加氢合成低碳烯烃催化活性。采用SEM、TEM、XRD、H₂-TPR和FT-IR等手段对催化剂进行了表征。结果表明,制备的催化剂前驱体呈50~70 nm的球形颗粒,表面富含羰基和羟基,物相组成以Fe₃O₄为主,用于反应后有Fe₅C₂和MnCO₃相生成。与共沉淀法制备催化剂相比,在设定的反应条件下,不同K含量改性的催化剂均具有较高的活性,以原料配比Fe:Mn:C₆:K=3:1:5:0.10的催化剂性能最佳,CO转化率达95.02%,总低碳烯烃收率为62.86 g/m³(H₂+CO),CH₄和CO₂选择性分别为13.88%和13.98%。     

同晶取代法制备Cu-Ni双金属催化剂及其催化CO加氢合成乙醇性能

采用定向同晶取代法制备了一系列镍孔雀石前驱体的Cu-Ni双金属催化剂。考察了前驱体结构以及催化剂表面组成对催化剂催化性能的影响,并采用浆态床反应器对催化剂的CO加氢制乙醇性能进行评价。实验结果表明,采用定向同晶取代法可以制备出（Cu,Ni）₂CO₃（OH）₂纯物相,取代后的Ni²⁺主要富集在前驱体（Cu,Ni）₂CO₃（OH）₂表面。焙烧后形成的（Cu_x,Ni_1-x）O固溶体均匀地分散在CuO晶体结构中。还原后的催化剂中Cu、Ni相互均匀分散形成活性界面,促进了低碳醇的合成。其中,不连续分布的Ni活性位点阻止了碳链的进一步增长,从而提高了乙醇选择性。当Ni/Cu原料比为45：100时,（Cu_x,Ni_1-x）O固溶体与CuO之间有较强的相互作用,表现出最好的反应活性和乙醇选择性。     

不同形貌Ni/γ-Al2O3催化剂催化CO甲烷化反应的研究

采用沉淀法分别以乙二醇、水、乙二醇-聚乙二醇600为修饰剂,制备了形貌分别为棒状（a-NiO）、粒状（b-NiO）和片状（c-NiO）结构的NiO催化剂,然后和γ-Al₂O₃通过研混法制得NiO/γ-Al₂O₃催化剂。采用XRD、TEM及H₂-TPR等技术手段对催化剂进行了表征。TEM观察NiO的形貌分别为棒状、粒状和片状。H₂-TPR结果表明,NiO/γ-Al₂O₃催化剂的氧化中心数量顺序为b-NiO/γ-Al₂O₃＜a-NiO/γ-Al₂O₃＜c-NiO/γ-Al₂O₃。XRD结果表明,NiO/γ-Al₂O₃催化剂还原后的Ni晶粒尺寸大小为b-Ni＞a-Ni＞c-Ni。在连续流动固定床反应装置上考察了Ni/γ-Al₂O₃对CO甲烷化反应的催化活性,研究了混合方法和形貌对CO甲烷化反应的影响。结果表明,研混法制得催化剂的活性及稳定性较好。催化剂形貌对CO甲烷化反应的催化活性顺序为c-Ni/γ-Al₂O₃＞a-Ni/γ-Al₂O₃＞b-Ni/γ-Al₂O₃,常压、593K和2500h^-1反应条件下,w_Ni为15% c-Ni/γ-Al₂O₃催化CO合成CH₄选择性及CO转化率分别达90.80%和99.63%。     

反应条件对固相合成负载羰基铑原子簇催化剂及其性能的影响

本文报告了由金属盐直接固相合成负载铑络合物或原子簇催化剂的新方法及IR谱表征。CO容易使表面吸附有水分子的RhCl_3/SiO_2还原并生成表面羰基物Rh~+-(CO)_2/SiO_2;CO、CO/H_2和CO/2H_2等不同还原气对表面络合物的生成没有影响。采用H_2还原只能得到金属Rh催化剂。水是重要影响因素,如果RhCl_3/SiO_2先抽空脱水,再用含水的CO还原,就会使Rh~+(CO)_2/SiO_2转化为Rh_6(CO)_(16)/SiO_2。此外,还考察了负载原子簇的CO加氢和热分解反应性能。采用CO还原RhCl_3/SiO_2制备的催化剂同负载原子簇催化剂的反应行为非常相近,而且比传统催化剂具有更高的反应活性。