环形电极单间隙电晕放电伏安特性

基于用于直线变压器型驱动源的多间隙气体开关结构,提出一种环形放电间隙与电晕针并联的气体火花间隙。通过测量间隙耐压过程中电晕放电的伏安特性,研究了气体介质、气压、电晕极性、电晕针长度以及针尖对应电极结构等因素对伏安特性的影响。结果表明:以空气为绝缘气体,负极性电晕可获得较稳定的伏安特性;改变电晕针长度和针尖对应电极结构可方便地实现对电晕放电伏安特性的调节以满足开关要求。     

放电参数对同轴枪中等离子体团的分离的影响

同轴枪中的等离子体团的分离现象主要是由同轴枪内磁场的梯度造成的电流层倾斜而引起的一个增强反馈过程导致的, 这种分离现象越来越成为限制同轴枪有效使用的一个不利因素. 在实验上研究放电参数对等离子体团的分离的影响, 对理论研究和实际应用都具有重要意义. 在实验中发现, 利用光电倍增管可以直接观察到等离子体团的分离程度, 由此可以研究放电参数对等离子体团的分离的影响. 本实验主要研究电容充电电压、电容、放电气压这三个参数对分层现象的影响. 实验发现, 分离程度随着电容以及其充电电压的增大而增强, 随着气压的增大而减弱. 实验结果基于雪犁模型进行分析, 电容以及电容充电电压的增大使放电电流增强使磁场梯度增大而导致电流层的倾斜程度增加, 而使等离子体团的分离程度变严重, 相反, 气压的增加使需要加速更多粒子而导致电流层的倾斜程度减弱, 而使等离子体团分离程度减弱. 分析认为, 通过控制在加速过程中影响电流层倾斜程度的因素可控制共轴枪中等离子体团的分离程度.     

同轴枪放电等离子体电流片的运动特性研究

同轴枪放电可以产生高速度、高密度的等离子体射流,在天体物理、核物理等研究领域具有广泛的应用.基于同轴枪放电等离子体运动的"雪犁模型"分析,本实验通过对等离子体光电信号和磁信号的测量及放电照片的拍摄,研究了不同放电电流和气压对同轴枪放电等离子体电流片的运动特性、电流通道分布的影响.实验结果发现:一次放电过程中,气压为10 Pa、放电电流为35.7—69.8 kA时,随着放电电流的增加,等离子体喷射速度增加,输运距离与离子携带的轴向动能成正比,大电流条件下,等离子体喷出枪口时易于在枪底端形成新的电流通道;气压为5—40 Pa、放电电流为49.8 kA时,随着气压的增加,等离子体喷射速度减小,输运距离缩短,高气压下,等离子体喷出枪口时在枪底端未产生新的放电通道,这与放电过程中遗留在枪底端的带电粒子和电流片渗漏残留在枪内的中性粒子共同形成的阻抗通道有关;电流反向时,二次放电击穿位置发生在电极头部,放电过程中存在多次放电现象.     

不同氩气气压下铝丝电爆炸的二次放电特性

搭建了RLC放电回路,研究了不同氩气气压下铝丝电爆炸二次放电特性。结果表明,随着气压的变化,电爆炸二次放电电压曲线呈U形。为了阐明氩气和铝蒸气在二次放电过程中的作用,利用光谱仪和高速分幅相机分别研究了二次放电等离子体的自辐射光谱特性和空间分布特性,发现:在低气压下氩气会参与放电,放电通道在铝蒸气表面;高气压下主要是铝蒸气放电,氩气基本不参与放电过程,放电通道在铝蒸气内部。     

同轴磁场对非平衡磁控溅射系统放电特性的影响

采用激励电流可以调整的电磁线圈来激发非平衡磁场,调整约束磁场和放电空间等离子体状态。实验结果表明调整非平衡磁场显著影响系统的放电特性,使放电特性偏离常规的磁控溅射系统放电特性,增强了等离子体的引出效果。在Ar放电的条件下,详细研究了溅射系统的工作伏安特性随不同的工作气体、气压和溅射功率的变化规律。根据蔡尔得公式,讨论了非平衡磁场对于磁控溅射系统中放电特性的影响规律。     

非平衡磁控溅射系统的离子束流控制

在非平衡磁控溅射沉积非磁性金属薄膜过程中,离子,原子到达比、沉积速率等参数是影响薄膜结构和性能的重要因素。根据非平衡磁控溅射沉积过程中离子的分布特点,分别考虑离子和中性粒子的传输,导出了对圆形平面靶非平衡磁控溅射沉积薄膜的放电功率、气压和离子束流密度等参数之间的关系,阐明了放电参数对于沉积过程离子束流密度等参数的影响。在Ar放电条件下,测量了系统的伏安特性;采用偏压平面离子收集电极测量了溅射系统轴向离子束流密度随不同的气压、溅射电流和空间位置的变化规律。结果表明模型分析的结论和实验数据的变化趋势相符合。     

介质阻挡放电中微放电周期特性的光学测量

采用特殊设计的双水电极介质阻挡放电装置,利用光学方法原位、无干扰地测量了大气压空气介质阻挡放电中微放电的单脉冲特性和周期特性,实验上首次发现在介质阻挡放电斑图模式中,微放电在驱动电压的正负半周的放电时刻并不是固定的,相邻两次放电的时间间隔是长短交替的。根据壁电荷对微放电通道相邻两次放电的不同作用,分析了相邻两次放电时刻的联系,很好地解释了相应的实验现象。     

纳秒脉冲电压下同轴场畸变开关多通道放电特性

使气体开关形成多通道放电是减小开关电感、通道电阻、电极熔蚀,提高开关寿命和稳定性的有效措施。设计了一种同轴场畸变气体火花开关,研究了开关在纳秒脉冲电压下的多通道放电现象。研究了脉冲电压上升速率与多通道放电特性的关系,比较了两种体积比的SF6/Ar混合气体多通道放电特性。实验结果表明:一定气压下,平均通道数随着脉冲电压上升率增加而增多,电流分布趋向均匀;相同脉冲峰值与气压比值,不同气压下,高气压下的通道数较多;SF6/Ar混合气体中,氩气含量较高情况下多通道放电特性较好。最后,结合J.C.Martin的多通道放电理论对实验结果作出了初步解释。     

Xe介质极紫外光源时间特性及最佳条件研究

理论和实验上研究了Xe介质毛细管放电极紫外光源等离子体时间特性和最佳条件. 从理论上建立了Xe介质一维辐射磁流体力学模型,模拟了不同气压和电流条件下等离子体压缩和辐射特性;实验上测量了放电电流30 kA时不同气压条件下13.5 nm （2%带宽）动态特性. 理论和实验结果表明：不同放电电流条件下,存在最佳气压值,最佳气压随着电流的增加而增加;同时,电流增加时,13.5 nm （2%带宽）辐射光强峰值时刻减小. 关键词： 极紫外光刻光源 毛细管放电 磁流体力学 Xe等离子体     

两间隙毛细管等离子体射流发生器主放电数值模拟

 消融放电毛细管等离子体发生器产生的等离子体射流具有密度高和温度相对低的特性,在许多领域都具有潜在的应用前景。利用1维流体模型对两间隙毛细管等离子体射流发生器的主放电特性进行了模拟计算分析。模型考虑了焦耳热效应和管壁烧蚀对放电特性的影响。在管壁消融这种反馈稳定机制作用下,毛细管放电处于准稳态,其产生的等离子体温度在放电期间保持恒定。在放电能量为1 kJ的条件下,聚乙烯毛细管等离子体温度可达3 eV,电子密度可达1025 m-3量级,射流速度接近10 km/s。改变放电输入的焦耳热功率密度,等离子体温度和速度变化较小,但气压、质量密度以及等离子体电子密度等特性参数均可以获得较大幅度的改变。     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.