一锅合成绿色到近红外发射的CdTe量子点

以3-巯基丙酸(MPA)为稳定剂,采用水相合成法制备了从绿色到近红外发射的CdTe量子点。系统研究了反应液pH值、镉和碲的物质的量之比及镉和3-巯基丙酸的物质的量之比等实验条件对CdTe量子点体系的发射波长和荧光量子产率的影响。在pH值为10.5,且nCd2+∶nTe2-∶nMPA=1∶0.05∶1.1的条件下,回流0.5 h,CdTe量子点体系在569 nm波长处的荧光量子产率达到30.8%;在7 h的回流时间内,制备的量子点的波长覆盖范围为525～730 nm。分别用X射线粉末衍射、透射电镜和红外光谱对CdTe量子点的晶体结构、形貌及表面基团进行表征。     

水热法合成巯基乙胺稳定的CdTe量子点

提出了一种以水热法合成巯基乙胺稳定的CdTe量子点的简单制备路线. 在优化的反应条件下, 产物的荧光量子效率最高达到19.7%, 接近已报道的其它方法的2倍. 考察了反应条件对产物的荧光性能的影响及产物在不同pH溶液中的稳定性.     

高质量CdTe量子点的水相快速合成

系统考察了水相合成CdTe量子点的主要影响因素, 通过改变无水乙醇-水体系的体积, 提高NaHTe的合成质量, 并调整反应温度, 改变反应的初始pH值, 在水相中快速合成了量子产率高、粒径分布范围窄的CdTe量子点, 实现了对量子点发光性质的调控, 在最佳条件(无水乙醇3 mL, 水1 mL, 反应初始pH 8.0, 反应温度40 ℃)下, 最高量子产率达68%. 量子点胶体溶液在回流过程中有时产生白色沉淀, 放置7 d后, 未过滤白色沉淀的量子点比过滤后的量子点荧光强度提高15%, 白色沉淀还有减小粒径分布的作用.     

超声电化学快速制备近红外CdTe量子点与细胞成像

针对当前水溶性量子点合成路线复杂、量子产率低的现状,在无需N2保护的条件下,采用简便的超声电化学方法快速合成了CdTe量子点前驱体;并对不同条件下制得的前驱体加热回流,得到水溶性、高质量的近红外CdTe量子点。产物的形貌、结构和组成通过高分辨透射电子显微镜(HRTEM)、X-射线粉末衍射(XRD)等手段进行了表征。考察了超声电化学参数和回流条件对量子点荧光性质的影响。通过控制电流脉冲宽度、反应时间、反应温度等参数,实现了CdTe量子点前驱体的可控制备;通过调节加热回流条件得到不同荧光发射波长的量子点;选用602 nm近红外发射波长的CdTe量子点标记了子宫颈癌细胞(Hela),并采用共聚焦技术实现了肿瘤细胞的显微成像观察。和传统的量子点合成方法相比,超声电化学方法具有合成路线简单、参数易调可控的特点;为高品质量子点的快速制备提供了新的思路,拓展了超声电化学在纳米材料制备领域的应用。     

超声电化学快速制备近红外CdTe量子点与细胞成像

针对当前水溶性量子点合成路线复杂、量子产率低的现状, 在无需N₂保护的条件下, 采用简便的超声电化学方法快速合成了CdTe量子点前驱体;并对不同条件下制得的前驱体加热回流, 得到水溶性、高质量的近红外CdTe量子点。产物的形貌、结构和组成通过高分辨透射电子显微镜(HRTEM)、X-射线粉末衍射(XRD)等手段进行了表征。考察了超声电化学参数和回流条件对量子点荧光性质的影响。通过控制电流脉冲宽度、反应时间、反应温度等参数, 实现了CdTe量子点前驱体的可控制备;通过调节加热回流条件得到不同荧光发射波长的量子点;选用602 nm近红外发射波长的CdTe量子点标记了子宫颈癌细胞(Hela), 并采用共聚焦技术实现了肿瘤细胞的显微成像观察。和传统的量子点合成方法相比, 超声电化学方法具有合成路线简单、参数易调可控的特点;为高品质量子点的快速制备提供了新的思路, 拓展了超声电化学在纳米材料制备领域的应用。     

水热法制备稳定的发光CdTe材料

采用水热合成技术将表面修饰有羧基的纳米CdTe微粒与表面活性剂和硅源进行自组装,得到了一种与氧化硅复合的稳定的CdTe发光材料.通过一系列表征手段(如TG-DTA,EDX,TEM,荧光光谱和N₂吸附)证实了CdTe微粒复合在氧化硅中.进一步通过烧结的方法除去表面活性剂,用稀酸除去金属氧化物,即得到多孔的氧化硅材料.     

水热法合成CdTe量子点及其与蛋白质连接作为生物荧光探针的研究

以巯基丙酸为稳定剂,采用水热法合成了CdTe量子点.吸收光谱和荧光光谱表明,所合成的CdTe量子点具有优异的发光特性.透射电子显微境(TEM)表征了纳米微粒的结构和粒径分布.并以牛血清白蛋白(BSA)为代表,通过测定CdTe量子点与BSA偶联(QDs-BSA)后溶液的荧光强度确定CdTe量子点与蛋白质偶联的最佳反应条件为pH 9～10,反应温度37 ℃,反应时间2 h.通过荧光发射光谱研究了溶液pH和NaCl浓度对QDs-BSA溶液和QDs溶液荧光强度的影响.在优化的反应条件下,用制备的QDs-BSA荧光探针对BSA进行了定量测定,线性范围是0.06～0.48 μg/mL,对0.24 μg/mL QDs-BSA样品7次测定的相对标准偏差是2.2%.     

电化学法合成强荧光CdTe量子点

采用电化学方法产生的H2Te为碲源(Te2-),快速合成了水溶性强荧光的CdTe量子点.该方法具有操作简单、安全、快速廉价和可大量制备等优点.合成过程中考察了合成温度,pH值和配体比例对制备CdTe量子点的影响.在最优化的实验条件下,电化学方法合成的巯基丙酸配位的CdTe荧光量子产率可达到55％;通过紫外可见光谱(UV...     

硫脲修饰法制备高发光性能CdTe量子点

通过巯基水解制备了具有优异荧光特性的碲化镉量子点. 详细研究前驱体镉离子与巯基丙酸(MPA)摩尔比、镉离子浓度等制备条件对大尺寸、高量子产率的亲水性碲化镉量子点光学性能的影响. 在不同的水热生长时间下, 可制备出荧光发射峰位于485-660 nm范围内的不同尺寸的碲化镉水溶性量子点, 荧光发射峰半高宽控制在40-75 nm之间, 量子点的最高量子产率(QY)达到了45%. 并利用硫脲缓慢水解和光解释放自由硫离子, 修饰碲化镉表面, 检测修饰后的量子点在12天内光学性能的变化情况. 通过考察硫脲用量对量子点修饰效果, 发现当n(CdTe)/n(thiourea)=1:4(量子点浓度以镉离子浓度计)时, 硫脲对发射峰为505 nm的碲化镉量子点修饰效果最为理想, 量子点荧光强度加强了5倍, 量子产率达到68.3%.     

CdTe量子点的无机合成及其荧光性质

以Na HTe为碲源,巯基乙酸为稳定剂,在水溶液中制得Cd Te前驱体(A);A分别采用微波辐射加热法(1)、水热合成法(2)和水浴回流法(3)制备了三种水溶性Cd Te纳米量子点(Cd Te-1t~Cd Te-3t),其结构经XRD和TEM表征。利用UV-Vis和荧光发射光谱考察了反应时间(t)对Cd Te-1t~Cd Te-3t荧光性质的影响。实验结果表明:在反应条件[微波功率400 W,温度96℃,微波辐射5 min]下,可快速制得Cd Te-15,量子产率41.16%,粒径3.2 nm,抗光漂白性能较好;延长反应时间,Cd Te-1t~Cd Te-3t的特征发射峰和特征吸收峰均红移,量子产率先增加后降低。     

Synthesis of NAC capped near infrared-emitting CdTeS alloyed quantum dots and application for in vivo early tumor imaging

The synthesis of water-soluble near-infrared (NIR)-emitting quantum dots (QDs) has recently received extensive attention for non-invasive detection of biological information in living subjects. Highly fluorescent CdTeS alloyed QDs for biological application are introduced in this paper. QDs were synthesized by a hydrothermal method and coated with N-acetyl-l-cysteine (NAC) as both bioactive ligand and sulfur source for biocompatibility and biological stability. The optical properties, morphology and structure of CdTeS alloyed QDs were characterized. The in vitro and in vivo toxicity was intensively investigated. Furthermore, the dynamics and bio-distribution of CdTeS alloyed QDs on living mice were studied. To explore biomedical application, folate-polyethylene glycol (FA-PEG) was used to decorate the CdTeS alloyed QDs (FP-CdTeS QDs) for targeted imaging of tumors over-expressing the folate receptor (FR). The tumor targeting capability of FP-CdTeS QDs on tumor bearing nude mice was demonstrated. The results showed that the prepared CdTeS QDs have excellent optical properties and low toxicity, which makes them an ideal inorganic material for biomedical imaging. In addition, the folate-PEG conjugated NIR-QDs displayed good biocompatibility as well as excellent sensitivity and specificity for optical imaging of tumors which can extend the application of CdTeS QDs.     

水相合成CdTe量子点测定海藻中微量碲

以亚碲酸钠(Na2TeO3)为Te源,CdCl2为Cd源,水合肼(SHJ)为还原剂,3-巯基丙酸(3-MPA)为稳定剂,制得λEX=380 nm和λEM=608 nm的CdTe量子点(CdTe QDs),该量子点的荧光强度与合成前Na2TeO3浓度呈线性关系.在n(Cd)/n(SHJ)=1∶0.04,n(Cd)/n(3...     

Conjugating luminescent CdTe quantum dots with biomolecules

Newly prepared CdTe quantum dots ( QD) bearing shells of water solubility providing capping agents (i.e., thioglycolic acid ( TGA) and 2-(dimethylamino)ethanethiol hydrochloride (DMAET) were subjected to electrostatic assays with several proteins (i.e., cytochrome c (cyt c) and human serum albumin (HSA). In particular, we employed absorption, emission, transient absorption and time-resolved emission spectroscopic means to test their response to light. Only for negatively capped QDs spectroscopic and kinetic evidence were gathered that corroborate the successful bioconjugation of QDs with cyt c to yield QD- cyt c bioconjugates. In fact, photoexcitation of QD-cyt c leads to a fast deactivation of the QD band gap emission and of the QD excited state. Notably, these interactions depend on the size of the QDs. Repulsive forces, on the other hand, are operative between the positively capped QDs and cyt c, hampering any bioconjugation.     

Ultrafast synthesis of near-infrared-emitting aqueous CdTe/CdS quantum dots with high fluorescence

The traditional aqueous route to synthesis CdTe/CdS Core/shell (c/s) quantum dots (QDs) via decomposition of Cd-thiol complexes is usually time consuming. Herein, an ultrafast and facile aqueous synthetic approach under atmospheric pressure for CdTe/CdS c/s QDs with emission from the green to the near-infrared window (535–820 nm) is reported. With purified CdTe core QDs diluted in solution of Cd-3-mercaptopropionic acid (MPA) complexes, CdTe/CdS c/s QDs with emission wavelengths at 700 and 800 nm can be obtained within 20- and 45-min refluxing under the optimized experimental conditions, respectively. This is the most rapid way to prepare CdTe/CdS c/s QDs in aqueous phase, and the obtained QDs were highly luminescent without postsynthesis treatment. The influences of various experimental factors, including Cd²⁺ concentration, MPA-to-Cd ratio, pH value, and dilution ratio on the growth rate and luminescent properties of the obtained CdTe/CdS c/s QDs, have been taken into consideration. The three processes “purification-dilution-addition” ensure the synthesis environment with high pH value and low core concentration and have a marked impact on the rapid synthesis rate and the resulting high fluorescence of CdTe/CdS c/s QDs.     

Hydrothermal synthesis of highly luminescent CdTe quantum dots by adjusting precursors’ concentration and their conjunction with BSA as biological fluorescent probes

A study on hydrothermal synthesis of CdTe quantum dots, highly luminescent nanocrystals at a relatively lower temperature, via changing the concentration of the CdTe precursors, is described. The full width at half maximum ranged from 40 to 80 nm and quantum yield (QY) was detected to be 27.4% at room temperature. The as-prepared CdTe QDs were labeled with BSA for fluorescence probes without pretreatment. Conjunction experimental results suggested that the as-prepared CdTe QDs are suitable for the application of biotechnology.     

Mechanism of antimicrobial activity of CdTe quantum dots

The antimicrobial activity and mechanism of CdTe quantum dots (QDs) against Escherichia coli were investigated in this report. Colony-forming capability assay and atomic force microscopy (AFM) images show that the QDs can effectively kill the bacteria in a concentration-dependent manner. Results of photoluminescence spectrophotometry, confocal microscopy, and antioxidative response tests indicate that the QDs bind with bacteria and impair the functions of a cell's antioxidative system, including down-regulations of antioxidative genes and decreases of antioxidative enzymes activities. The oxidative damage of protein and lipid is also observed with thiobarbituric reacting substances and protein carbonyl assays, respectively. On the basis of these results, it is proposed that the mechanism of the antimicrobial activity of CdTe QDs involves QDs-bacteria association and a reactive oxygen species-mediated pathway. Thus, CdTe QDs could have the potential to be formulated as a novel antimicrobial material with excellent optical properties.     

Self-electrochemiluminescent CdTe quantum dots: one-pot synthesis,characterization, and electrochemical properties

Journal of Solid State Electrochemistry - A novel self-electrochemiluminescent (self-ECL) nanomaterial, CdTe quantum dots, was prepared by the one-pot method using 2-diethylaminoethanethiol...     

水溶性CdTe量子点的合成及其用于荧光猝灭法测定肌红蛋白

以3-巯基丙酸为稳定剂,合成了具有特殊光学性质的水溶性CdTe量子点,其最大发射波长位于544 nm.利用荧光光谱、紫外可见光谱及圆二色光谱法系统的研究了CdTe量子点与肌红蛋白(Mb)二者结合前后体系光谱的变化,从而证实了CdTe量子点与Mb之间静电结合反应的特征.在pH 7.0的PBS缓冲液中,用CdTe量子点作为荧光探针研究了肌红蛋白与量子点的相互作用,并基于肌红蛋白对CdTe量子点有显著的荧光猝灭作用,建立了肌红蛋白的快速检测方法.在最佳实验条件下,该体系荧光强度的猝灭程度(△F)与肌红蛋白质量浓度呈良好的线性关系,线性范围为0.3～24 μg/mL,检出限为0.13 μg/mL.该方法已对合成样品中肌红蛋白进行检测,并用于人体尿样中肌红蛋白的测定.     

Electrochemical properties of CdSe and CdTe quantum dots

Semiconductor nanocrystal quantum dots (QDs), owing to their unique opto-electronic properties determined by quantum confinement effects, have been the subject of extensive investigations in different areas of science and technology in the past two decades. The electrochemical behaviour of QDs, particularly for CdSe and CdTe nanocrystals, has also been explored, although to a lesser extent compared to the optical properties. Voltammetric measurements can be used to probe the redox levels available for the nanocrystals, which is an invaluable piece of information if these systems are involved in electron transfer processes. Electrochemical data can also foster the interpretation of the spectroscopic properties of QDs, and give insightful information on their chemical composition, dimension, and surface properties. Hence, electrochemical methods constitute in principle an effective tool to probe the quality of QD samples in terms of purity, size dispersion, and surface defects. The scope of this critical review is to discuss the results of electrochemical studies carried out on CdSe and CdTe core and core-shell semiconductor nanocrystals of spherical shape. Examples of emerging or potential applications that exploit electroactive quantum dot-based systems will also be illustrated.