Pressure effect on adhesion

Zusammenfassung Unter der Voraussetzung von Verknüpfungen wird die Anfangsgeschwindigkeit der Adhäsion untersucht.Wenn Epoxyharz-Aminsysteme als Klebstoff gebraucht werden, ist die Beziehung zwischen Härtezeit und Anfangs-Bindefestigkeit theoretisch wie folgt gegeben:S(t)/S(t ₀ )=t+1. Dabei sindS(t) undS(t ₀) die Klebefestigkeit nach den Härtezeitent bzw.t ₀ ist ein Maß für das Ansteigen der Verknüpfungen, t=t–t₀.Die Beziehung zwischen Härtungsdruck und Verhältnis der Klebfestigkeiten lautet lnS(p)/S(p ₀ )=ln+·p. Wieder sind die Werte der FestigkeitenS aufp bzw.p ₀ auf die Drucke bezogen. und sind Konstanten.Die experimentellen Ergebnisse für das Kleben von Kupfer mit Epoxyharz-Aminsystemen bestätigen diese theoretischen Voraussagen.

---

---

With 7 figures and 3 tables     

Phase state effect on adhesion behavior of self-assembled monolayers

The effect of phase state of self-assembled monolayers (SAMs) on adhesion behavior was studied using a combination of atomic force microscopy (AFM) and Johnson-Kendall-Roberts (JKR) methods. The phase state of SAMs was controlled by adjusting the reaction temperature. Order-to-disorder structural transitions in monolayers of n-alkyltrichlorosilanes resulted in dramatic increases in adhesion force and adhesion hysteresis, which represents the first report of alterations in adhesion properties due to phase changes of monolayers without any effect of chain length and surface heterogeneity. This increase in mechanical deformation of the disordered monolayer is understood to be caused by increases in (1) molecular contact between the AFM tip and a disordered monolayer due to the more deformable state of the latter and (2) monolayer deformation during unloading by the JKR probe lens. Adhesion hysteresis was found to have greater sensitivity toward the unloading rate for disordered monolayers. The occurrence of maximum hysteresis at faster rates proves that monolayer chain mobility increases with structural disorder, resulting in increased mechanical deformation.     

The effect of solvent polarity on the molecular surface properties and adhesion of Escherichia coli

The elasticity and molecular surface characteristics of Escherichia coli JM109 were investigated via atomic force microscopy (AFM) in solvents expressing different polarities. The nature of bacterial adhesion and surface characteristics was probed in formamide, water, and methanol, with dielectric constants of 111, 80, and 33, respectively. Solvent polarity affected the elasticity of the bacterium, the conformation of the cell surface biopolymers, the height of the surface biopolymers, and measured adhesion forces between the bacterium and silicon nitride. By applying the Hertz model to force-indentation data, we determined that the Young's modulus was greatest in the least polar solvent, with values of 182 +/- 34.6, 12.8 +/- 0.1, and 0.8 +/- 0.3 MPa in methanol, water, and formamide, respectively. The thickness of the biopolymer brush layer on the bacterial surface was quantified using a steric model, and these values increased as polarity increased, with values of 27, 93, and 257 nm in methanol, water, and formamide, respectively. The latter results suggest that highly polar conditions favor extension of the biopolymer brush layer. Cross-sectional analysis performed on tapping mode images of the bacterial cells in methanol, water, and formamide further supported this hypothesis. The image height values are larger, since the image analysis measures the height of the bacterium and the polymer layer, but the trend with respect to solvent polarity was the same as was obtained from the steric model of the brush length. Measured adhesion forces scaled inversely with solvent polarity, with greatest adhesion observed in the least polar solvent, methanol. The combined conformational changes to the bacterial surface and biopolymer layer result in different presentations of macromolecules to a substrate surface, and therefore affect the adhesion forces between the bacterial molecules and the substrate. These results suggest that polarity of the solvent environment can be manipulated as a design parameter to control or modify the bacterial adhesion process.     

Contact angle of polyethylene on copper and its effect on adhesion

To determine whether the large differences in adhesion for polyethylene coatings applied to different types of copper surface could be attributed to changes in work of adhesion or wettability, the variations of contact angle with time has been measured for molten polyethylene droplets on these surfaces. It is concluded from these measurements that the low peel strengths obtained on certain substrates cannot be accounted for by a low work of adhesion of poor wetting of the surface.     

The effect of aminoalkoxy and glycidoxyalkoxy silanes on adhesion characteristics of double and triple copolymers of ethylene

The effect of aminoalkoxy and glycidoxyalkoxy silanes on strength of a polyethylene-modified copolymer-metal (polyethylene terephthalate) adhesion joint was studied for double and triple acetate copolymers of ethylene. It was shown that such modification resulted in an essential increase in the deformation-strength and adhesion characteristics of adhesive joints.     

The adhesion kinetics of sticky vesicles in tension: the distinction between spreading and receptor binding

We investigate the kinetics of spreading and adhesion between polymer vesicles decorated with avidin and biotin, held in micropipettes to maintain fixed tension and suppress membrane bending fluctuations. In this study, the density of avidin (actually Neutravidin) and biotin was varied, but was always sufficiently high so that lateral diffusion in the membrane was unimportant to the adhesive mechanism or rate. For a stunning result, we report a concentration-dependent distinction between adhesion and spreading: At low surface densities of avidin and biotin, irreversible vesicle adhesion is strong enough to break the membrane when vesicle separation is attempted, yet there is no spreading or "wetting". By this we mean that there is no development of an adhesion plaque beyond the initial radius of contact and there is no development of a meaningful contact angle. Conversely, at 30% functionalization and greater, membrane adhesion is manifest through a spreading process in which the vesicle held at lower tension partially engulfs the second vesicle, and the adhesion plaque grows, as does the contact angle. Generally, when spreading occurs, it starts abruptly, following a latent contact period whose duration decreases with increasing membrane functionality. A nucleation-type rate law describes the latency period, determined by competition between bending and sticking energy. The significance of this result is that, not only are membrane mechanics important to the development of adhesion in membranes of nanometer-scale thickness, mechanics can dominate and even mask adhesive features such as contact angle. This renders contact angle analyses inappropriate for some systems. The results also suggest that there exist large regions of parameter space where adhesive polymeric vesicles will behave qualitatively differently from their phospholipid counterparts. This motivates different strategies to design polymeric vesicles for applications such as targeted drug delivery and biomimetic scavengers.     

Inhibitory effect of hydrophilic polymer brushes on surface-induced platelet activation and adhesion

Poly(N,N-dimethylacrylamide) (PDMA) brushes are successfully grown from unplasticized poly(vinyl chloride) (uPVC) by well-controlled surface-initiated atom transfer radical polymerization (SI-ATRP). Molecular weights of the grafted PDMA brushes vary from ≈ 35,000 to 2,170000 Da, while the graft density ranges from 0.08 to 1.13 chains · nm(-2). The polydispersity of the grafted PDMA brushes is controlled within 1.20 to 1.80. Platelet activation (expression of CD62) and adhesion studies reveal that the graft densities of the PDMA brushes play an important role in controlling interfacial properties. PDMA brushes with graft densities between 0.35 and 0.50 chains · nm(-2) induce a significantly reduced platelet activation compared to unmodified uPVC. Moreover, the surface adhesion of platelets on uPVC is significantly reduced by the densely grafted PDMA brushes. PDMA brushes that have high molecular weights lead to a relatively lower platelet activation compared to low-molecular-weight brushes. However, the graft density of the brush is more important than molecular weight in controlling platelet interactions with PVC. PDMA brushes do not produce any significant platelet consumption in platelet rich plasma. Up to a seven-fold decrease in the number of platelets adhered on high graft density brushes is observed compared to the bare PVC surface. Unlike the bare PVC, platelets do not form pseudopodes or change morphology on PDMA brush-coated surfaces.     

The effect of surface roughness on the adhesion of solid surfaces for systems with and without liquid lubricant

We present molecular dynamics results for the interaction between two solid elastic walls during pull-off for systems with and without octane (C(8)H(18)) lubricant. We used two types of substrate--flat and corrugated--and varied the lubricant coverage from approximately 1/8 to approximately 4 ML (monolayers) of octane. For the flat substrate without lubricant the maximum adhesion was found to be approximately three times larger than for the system with the corrugated substrate. As a function of the octane coverage (for the corrugated substrate) the pull-off force first increases as the coverage increases from 0 to approximately 1 ML, and then decreases as the coverage is increased beyond monolayer coverage. It is shown that at low octane coverage, the octane molecules located in the substrate corrugation wells during squeezing are pulled out of the wells during pull-off, forming a network of nanocapillary bridges around the substrate nanoasperities, thus increasing the adhesion between two surfaces. For greater lubricant coverages a single capillary bridge is formed. The adhesion force saturates for lubricant coverages greater than 3 ML. For the flat substrate, during pull-off we observe discontinuous, thermally activated changes in the number n of lubricant layers (n-1-->n layering transitions), whereas for the corrugated substrate these transitions are "averaged" by the substrate surface roughness.     

The effect of surface microtopography of poly(dimethylsiloxane) on protein adsorption, platelet and cell adhesion

Chemical homogeneous poly(dimethylsiloxane) (PDMS) surface with dot-like protrusion pattern was used to investigate the individual effect of surface microtopography on protein adsorption and subsequent biological responses. Fibrinogen (Fg) and fibronectin (Fn) were chosen as model proteins due to their effect on platelet and cell adhesion, respectively. Fg labeled with ¹²⁵I and fluorescein isothiocyanate (FITC) was used to study its adsorption on flat and patterned surfaces. Patterned surface has a 46% increase in the adsorption of Fg when compared with flat surface. However, the surface area of the patterned surface was only 8% larger than that of the flat surface. Therefore, the increase in the surface area was not the only factor responsible for the increase in protein adsorption. Clear fluorescent pattern was visualized on patterned surface, indicating that adsorbed Fg regularly distributed and adsorbed most on the flanks and valleys of the protrusions. Such distribution and local enrichment of Fg presumably caused the specific location of platelets adhered from platelet-rich plasma (PRP) and flowing whole blood (FWB) on patterned surface. Furthermore, the different combination of surface topography and pre-adsorbed Fn could influence the adhesion of L929 cells. The flat surface with pre-adsorbed Fn was the optimum substrate while the virgin patterned surface was the poor substrate in terms of L929 cells spread.     

Nano/microstructural effect of hydroxyapatite nanocrystals on hepatocyte cell aggregation and adhesion

Hepatocyte cell aggregation and adhesion to HAp nanocrystals covered with SU-8 polymer micropatterns by nano/microfabrication techniques is demonstrated. The surface roughness and wettability of the HAp nanocrystals are significantly different from those of the SU-8 polymer. QCM-D and microscopic observation clearly reveal that the cells realize the surface properties to form aggregation and preferentially adhere to the HAp nanocrystals at 2 h after seeding, indicating the importance of the microstructures as well as the interfacial phenomena at a nanometer scale.     

Time-dependent conformational changes in adsorbed albumin and its effect on platelet adhesion

Recent studies have shown that platelets can adhere to adsorbed albumin (Alb) through a receptor-mediated mechanism, but only if the Alb undergoes more than a critical degree of adsorption-induced unfolding. The objectives of this research were to investigate whether Alb that was initially adsorbed in a manner that induced unfolding that was less than this critical level would undergo further unfolding with time and, if so, whether this would induce the onset of platelet adhesion once this critical level was exceeded. To address these questions, CD spectropolarimetry was used to monitor the structure of Alb on OH- and CH(3)-functionalized alkanethiol self-assembled monolayer surfaces, with the Alb initially adsorbed under conditions resulting in degrees of unfolding that were below this critical level, and then the adsorbed Alb layers were aged over 6 months in sterile physiological saline at 37 °C. Platelet adhesion to Alb was quantified at selected time points via a lactate dehydrogenase (LDH) assay. The results indicate that an adsorbed Alb layer does undergo further structural changes with increasing residence time and supports platelet adhesion once it unfolds beyond the previously determined critical level. These results may be relevant to the clinically observed problem of the onset of late-thrombosis, which occurs on cardiovascular implants such as drug-eluting stents.     

Lack of effect of an externally applied electric field on bacterial adhesion to glass

Deposition to glass of Streptococcus salivarius HB-C12 and Staphylococcus epidermidis 3399 in a parallel plate flow chamber in the absence and presence of an externally applied electric field has been studied experimentally. No effect on bacterial adhesion, including initial deposition rates, numbers of adhering bacteria after 4 h, spatial distributions of adhering bacteria and air bubble induced detachment, was found. A theoretical analysis shows that electric fields applied over a 150 μm thin glass substratum do not have a sufficiently strong effect on its surface potential to influence bacterial adhesion.     

The effects of energetic ion irradiation on metal-to-polymer adhesion

In this study, the simple and effective surface modification of polymers through ion irradiation is described to improve metal-to-polymer adhesion. The surface of polymer films was irradiated with 150 keV Xe⁺ ions at various fluences, and copper (Cu) was then deposited onto the surface-modified polymer films. The surface properties of the modified films were investigated in terms of their wettability, chemical composition, and surface morphology. The metal-to-polymer adhesion strength was estimated using a nano-indenter. As a result, the surface environment of the polymer films was physiochemically changed by ion irradiation, which could have a significant effect on the metal-to-polymer adhesion. The irradiated polymer films exhibited a higher adhesion strength than the control film, and the strength depended on the fluence. The maximum adhesion strength (8.45 mN) of the Cu deposited on the irradiated PEN films was obtained at a fluence of 5×10¹⁴ ions/cm².     

Tilt of atomic force microscope cantilevers: effect on spring constant and adhesion measurements

In atomic force microscopy, the cantilevers are mounted under a certain tilt angle alpha with respect to the sample surface. In this paper, we show that this increases the effective spring constant by typically 10-20%. The effective spring constant of a rectangular cantilever of length L can be obtained by dividing the measured spring constant by cos2 alpha(1 - 2D tan alpha/L). Here, alpha is the tilt angle and D is the size of the tip. In colloidal probe experiments, D has to be replaced by the radius of the attached particle. To determine the effect of tilt experimentally, the adhesion force between spherical borosilicate particles and planar silicon oxide surfaces was measured at tilt angles between 0 degrees and 35 degrees. The experiments revealed a significant decrease of the mean apparent adhesion force with a tilt of typically 20-30% at alpha = 20 degrees. In addition, they demonstrate that the adhesion depends drastically on the precise position of contact on the particle surface.     

The adhesion and spreading of thrombocyte vesicles on electrode surfaces

The interaction of thrombocyte vesicles with the surface of metal electrodes, i.e., mercury, gold and gold electrodes modified with self assembled monolayers (SAM), was studied with the help of chronoamperometry, atomic force microscopy, and quartz crystal microbalance measurements. The experimental results show that the interaction of the thrombocyte vesicles with the surface of the electrodes depends on the hydrophobicity of the latter: whereas on very hydrophobic surfaces (mercury and gold functionalized with SAM) the thrombocyte vesicles disintegrate and form a monolayer of lipids, on the less hydrophobic gold surface a bilayer is formed. The chronoamperometric measurements indicate the possibility of future applications to probe membrane properties of thrombocytes.