具有结晶孔壁介孔镁锌氧复合物(英文)

以介孔碳为硬模板经过二次填充制备了介孔镁锌氧复合物.采用X射线衍射(XRD),透射电镜(TEM),扫描电镜(SEM),N2吸附脱附等手段对材料的结构及形貌进行了表征.结果表明,所制备的材料在具有高有序介孔结构的同时还具有结晶的孔壁.孔径尺寸均为4.0nm,比表面积均为114.5m2.g-1.广角XRD结果初步表明,材料中氧化镁和氧化锌复合形成了固溶体.该材料作为一种半导体材料有望在光学器件领域获得新的应用价值.     

氩吸附法研究多级孔分子筛的孔结构

采用不同方法分别制备了双介孔分子筛、介微孔分子筛及介孔沸石材料,利用氩吸附法并结合XRD技术表征了多级孔分子筛的孔结构。探讨了适用于多级孔分子筛的孔径分布计算方法,揭示了不同类型吸附等温线与孔径分布、孔型及孔容等之间的关系。研究表明,对于多级孔分子筛、微孔和介孔的孔径分布分别用SF法和BJH法计算较适宜,全孔分析可用NLDFT法计算。通过对TS-1介孔沸石的孔结构分析发现, TPAOH 在改性制备介孔TS-1的过程中起到了生成介孔及促进二次晶化的双重作用。     

共缩聚法制备有序介孔氧化硅纳米螺旋纤维

在传统球状介孔氧化硅合成工作的基础上,以正硅酸乙(TEOS)和γ-巯丙基三甲氧基硅烷(MPTMS)为硅源,在水体系下利用共缩聚法一步合成出具有介孔分子筛结构特征的纳米纤维,并通过扫描电子显微镜(SEM)、小角X射线衍(XRD)、透射电子显微镜(TEM)和氮气吸附-脱附实验对样品进行了表征与分析.     

不同pH值下合成的双中孔和六方中孔SiO_2的表征(英文)

在相同的反应体系中当ｐｈ值从约９．５调变至１１时分别合成出双中孔ＳｉＯ２和六方中孔ＳｉＯ２材料,并用ＸＲＤ、Ｎ２吸附、ＴＥＭ、ＴＧ／ＤＴＡ和ＦＴＩＲ等测试手段对合成产物进行了表征。实验结果表明,双中孔ＳｉＯ和六 方中孔ＳｉＯ２是合成中必然出现的两种不同的中孔物相。与六方中孔ＳｉＯ２相比,双中孔ＳｉＯ２也具有典型中孔 材料的特征ＸＲＤ谱图,虽然仅呈现一个易让人产生不完全晶化误解的相对较宽的单ＸＲＤ衍射峰（ｄ＝５．２ｎｍ）,但它却给出一种独特的Ｎ２吸附等温线和窄的双峰中孔孔径分布曲线。由于孔壁的无定形及表面活性剂分子与ＳｉＯ２骨架间相似的相互作用,两类材料给出类似的ＦＴＩＲ谱图和ＴＧ／ＤＴＡ曲线。然而,在双中孔ＳｉＯ２的ＦＴＩＲ谱图中９６０ｃｍ处峰强度的微小变化可能意味着在锻烧脱除模板剂后双中孔ＳｉＯ２较六方中孔ＳｉＯ２具有更高的骨架聚合度。     

Preparation and characterization of highly photoactive nanocrystalline TiO_2 powders by solvent evaporation- induced crystallization method

Highly photoactive bi-phase nanocrystalline TiO2 photocatalyst was prepared by a solvent evaporation-induced crystallization (SEIC) method, and calcined at different temperatures. The obtained TiO2 photocatalyst was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalytic activity was evaluated by the photocatalytic oxidation of acetone in air. The results show that solvent evaporation can promote the crystallization and phase transformation of TiO2 at 100℃. When calcination temperatures are below 600℃, the prepared TiO2 powders show bimodal pore size distributions in the mesoporous region. At 700℃, the pore size distributions exhibit monomodal distribution of the inter-aggregated pores due to the collapse of the intra-aggregated pores. At 100℃, the obtained TiO2 photocatalyst by this method shows good photocatalytic activity, and at 400℃, its photocatalytic activity exceeds that of Degussa P25. This may be attributed to the fact t     

氧化钨介孔材料的制备与表征

以介孔二氧化硅(KIT-6)为硬模板, 硅钨酸为钨源, 用硬模板法制备WO3-SiO2复合材料, 再利用HF除去二氧化硅, 得到了介孔三氧化钨材料. 用X射线衍射(XRD)、能量扩散X射线(EDX)、高分辨透射电镜(HRTEM)、N2吸附-脱附等表征手段, 对制备复合材料的物料比、煅烧温度以及不同分散剂等条件进行了考察. 结果表明, 硅钨酸与硅介孔的物料比(m(WO3)/m(SiO2))在3:1到4:1之间, 在600-750 ℃下煅烧, 能制备结构较好的介孔氧化钨. 乙醇和蒸馏水为分散剂时, 用乙醇为分散剂所得的介孔WO3材料具有更高的比表面积和孔体积.     

银掺杂介孔氧化铝抗菌剂的一步合成与表征

以Al(NO_3)_3·9H_2O和AgNO_3为原料,采用水热法制备了介孔氧化铝纳米粒子(Mesoporous Al_2O_3NPs)和银掺杂介孔氧化铝纳米粒子(Mesoporous Ag/Al_2O_3NPs),通过X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)、X射线荧光光谱(XRF)、能量分散X射线衍射(EDX)和低温N2吸附-脱附等手段对产物进行了表征,通过最低抑菌浓度和抑菌圈实验研究了材料的抗菌性能.XRD分析表明在介孔Ag/Al_2O_3NPs中Al_2O_3是唯一结晶相,Ag掺杂后,介孔Ag/Al_2O_3NPs晶格常数和半高峰宽增大,晶面间距[(111),(400)和(440)面]减小.FE-SEM形貌分析表明掺杂后的介孔Ag/Al_2O_3NPs颗粒直径减小而孔径增大.EDX和XRF分析表明介孔Ag/Al_2O_3NPs中O/Al摩尔比为1.5,与Al_2O_3NPs中O/Al摩尔比相同.综合XRD和XRF分析结果认为,Ag进入介孔Al_2O_3晶格间隙形成间隙固溶体.低温N2吸附-脱附分析表明掺杂后的介孔Ag/Al_2O_3NPs比表面积、孔体积和孔径增大.曝气抗菌实验结果表明介孔Ag/Al_2O_3NPs的抗菌机理是活性氧和金属银的协同作用.介孔Ag/Al_2O_3NPs对革兰氏阴性菌(大肠杆菌)和革兰氏阳性菌(金黄色葡萄球菌)具有明显的抗菌效果,对大肠杆菌和金黄色葡萄球菌的最低抑菌浓度(MIC)均为80μg/m L,抑菌圈直径分别为26 mm和24 mm.     

Characterization Studies on the Ionic Liquid-Templated Mesoporous Silica with Wormlike Pores

This article reports a novel preparation of wormlike mesoporous silica with 1-hexadecane-3-methylimidazolium bromide (C₁₆MIM)Br, a kind of room-temperature ionic liquids (RTILs), as a template via a sol-gel nanocasting technique. The characterization studies were carried out in contrast with that of the mesoporous silica with cetyltrimethylammonium bromide (CTAB), a usually used template, which has the same alkyl chain length with (C₁₆MIM)Br. The structures of the silica materials have been characterized by Transmission electron microscopy (TEM), High-resolution TEM (HRTEM) and N₂ adsorption-desorption measurements. The results show that both the mesoporous materials prepared with different templates respectively can form regular wormlike mesopores with ca. 2 nm in pore diameter. They also have large BET surface areas with narrow size distribution. Compared to the CTAB-template mesoporous silica, the material with (C₁₆MIM)Br as a template has highly uniform pore size and larger surface area. In addition, the formation mechanism of the wormlike mesopores with RTIL has been proposed by an electrostatic charge matching assembly-pathway and steric factor.     

负载Ni金属有序介孔氧化铝催化剂的制备及表征

采用原位合成法和传统浸渍法以价格低廉的硝酸铝作为铝源, 聚乙二醇1540为模板剂, 硝酸镍为镍源, 制备出负载Ni金属有序介孔氧化铝催化剂, 并采用BET、TEM、XRD、TG多种测试技术对合成催化剂的物理化学性质和结构特征进行了表征. 实验结果表明, 两种方法均能制备出比表面积大(＞210 m2·g-1)、孔径分布窄(4 nm左右)的负载Ni金属介孔氧化铝催化剂. 与浸渍法相比, 原位合成法所制备的负载Ni金属有序介孔氧化铝镍离子与载体具有更强的相互作用力, 且孔结构具有一定的有序性.     

高比表面积有序介孔氧化铝的制备与表征

采用溶胶-凝胶法以非离子表面活性剂PEO-PPO-PEO三嵌段共聚物F127为模板剂, 以异丙醇铝为铝源, 以异丙醇为溶剂, 成功地制备出比表面积为485 m2/g、孔径分布窄(2~20 nm)、孔容在1.2 cm3/g以上和孔道呈蠕虫状且具有一定有序性的介孔氧化铝. 采用BET, TEM, XRD和TG多种测试技术对产物性能进行了表征. 探讨了水铝比、醇水混合溶液的滴加速度、反应时间、水浴温度、陈化温度及陈化时间等条件对合成的有序介孔氧化铝结构的影响.     

纳米晶簇多级孔道L沸石的合成及其脱硫性能

采用晶化培育法制备了L沸石纳米晶簇,以其作为前驱体,并以3-三甲基甲硅烷基丙基十六烷基二甲基氯化铵(TPHAC)为模板剂,合成了微孔-介孔多级孔道L沸石(MeLTL沸石).通过X射线衍射(XRD)、氮气吸附-脱附、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、27Al固体魔角核磁(27AlMASNMR)和吡啶傅立叶变换红外(Py-FTIR)等方法对MeLTL沸石进行了表征.研究结果表明,MeLTL沸石是由L沸石纳米晶簇自组装形成的,并具有介孔孔道和L沸石的微孔结构以及适宜的酸量与酸强度,其比表面积和孔体积分别高达611m2.g-1和0.696cm.3g-1.将MeLTL沸石作为添加剂引入柴油加氢脱硫催化剂载体中,并与添加L沸石、Al-MCM-41和仅以γ-Al2O3为载体的催化剂进行比较,其脱硫性能为最佳,经加氢后的柴油硫含量仅为9.3μg.g-1,脱硫率达99.3%.     

乙烯基官能化MSU-X的合成

分别在非离子表面活性剂（AEO9或Tx-15）的存在下,采用共水解缩聚一步合成了乙烯基官能化MSU-X型中孔分子筛（V-MSU-1, V-MSU-2）,并对其合成过程,材料的结构和表面性质进行了比较研究. 乙烯基官能化后, 乙烯基团以共价键的方式与SiO2骨架相连并均匀分布于孔道表面, 改善了分子筛孔道的疏水性能.不同的模板剂及前驱体中有机官能基的含量对V-MSU-X孔道特征、表面和织构性能有一定的影响.     

预置晶种合成MCM-41/ZSM-3复合分子筛

以十六烷基三甲基溴化铵和四甲基氢氧化铵为模板剂，以ZSM-3为晶种，在水热条件下合成了同时具有中孔和微孔的复合分子筛MCM-41/ZSM-3。通过XRD、IR、N2吸附脱附等温线和SEM表征，样品的XRD图谱在小角度衍射区和大角度衍射区同时出现了MCM-41和ZSM-3的衍射峰；IR图谱上也同时出现了MCM-41和ZSM-3的吸收谱带，并且合成样品与两种分子筛的机械混合物有明显差别；N2吸附脱附等温线证明样品含中孔和微孔结构，并且微孔直径集中分布在0.7 nm左右，中孔直径集中分布在3.3 nm左右；从SEM照片可以看出，复合分子筛和机械混合物形貌不同，前者为附晶生长或再结晶，后者为均匀分散。     

Synthesis, amino-functionalization of mesoporous silica and its adsorption of Cr(VI)

Mesoporous silica materials with a centered rectangular symmetry (cmm) have been synthesized through a facile direct-templating method using tetraethylorthosilicate (TEOS) and amphiphilic block co-polymers Pluronic P123 under acidic conditions. The amino groups have been grafted to as-synthesized mesoporous silica by [1-(2-amino-ethyl)-3-aminopropyl]trimethoxysilane (AAPTS). Thus obtained amino-functionalized mesoporous silica (denoted as NN-silica) was used for sequestration of Cr(VI) from aqueous solution. After sequestration of Cr(VI), the sample was denoted as Cr(VI)-silica. The parent mesoporous silica, NN-silica and Cr(VI)-silica were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and N(2) adsorption-desorption isotherms. XRD and TEM results confirm that the structure of these samples is centered rectangular symmetry (cmm). N(2) adsorption-desorption isotherms show that there is a remarkable decrease in surface area and pore volume for NN-silica (S(BET)=54.5 m(2)g(-1), V(P)=0.09 cm(3)g(-1)) and Cr(VI)-silica (S(BET)=53.2 m(2)g(-1), V(P)=0.07 cm(3)g(-1)) compared to the parent mesoporous silica (S(BET)=444.0 m(2)g(-1), V(P)=0.71 cm(3)g(-1)). The BJH desorption average diameter of NN-silica, Cr(VI)-silica and the parent mesoporous silica is 4.40 nm, 4.07 nm and 5.11 nm, respectively. The results reveal the channels of as-synthesized mesoporous silica are essentially grafted with abundant amino groups and loaded with Cr(VI). The adsorption experiment results show that the functionalized mesoporous silica materials possess an increased Cr(VI) adsorption capacity and the maximum Cr(VI) loadings at 25, 35 and 45 degrees C can reach 2.28, 2.86 and 3.32 mmol/g, respectively.     

W掺杂SiO2介孔材料的制备与表征

以非离子表面活性剂三嵌段共聚物P123为模板剂、正硅酸乙酯(TEOS)为硅源、钨酸钠(Na2WO4·2H2O)为钨源, 通过水热法一步合成了W掺杂的二氧化硅介孔材料W-SiO2, 并通过XRD、HRTEM、EDX、FT-IR、N2吸附-脱附等表征手段, 考察了随着W含量增加, W-SiO2介孔材料结构的变化规律以及钨物种在材料中的存在状态. 结果表明, 当WO3含量w(WO3)约为10%时, W-SiO2中的钨物种是高度分散进入介孔骨架,形成W-O-Si 键; 当w(WO3)=20%时, 样品中开始有未掺入到SiO2骨架中WO3的结晶出现; 当w(WO3)约60%时, W-SiO2 样品能保持很好的介孔孔道结构, 更高含量WO3掺入将破坏二氧化硅介孔结构.     

模板剂对全硅MCM-41介孔分子筛结构的影响

分别采用十六烷基三甲基溴化铵和十六烷基三乙基溴化铵作为模板剂,硅溶胶为硅源,用水热晶化法在碱性（NaOH）介质中合成了MCM-41介孔分子筛样品.通过XRD、N2吸附-脱附、TG-DTA、IR等测试手段对这两种样品进行了对比表征分析.考察了两种不同模板剂对其晶体结构、比表面及孔径大小的影响.实验结果表明,相对于十六烷基三甲基溴化铵做模板剂,采用大头基的十六烷基三乙基溴化铵可以合成较大孔径和孔容（分别为4.72 nm和1.14 cm3•g-1）的MCM-41介孔分子筛,而且具有较窄的孔径分布,因此对于合成大孔径的介孔分子筛MCM-41,十六烷基三乙基溴化铵是一种很好的模板剂.     

双中孔SiO_2的合成与表征

在通常用于合成中孔ＭＣＭ－４１分子筛的反应体系中,用氨水、ＮａＯＨ或四乙基氢氧化胺作催化剂,在较低的ｐＨ值下合成出具有独特Ｎ２吸附等温线和狭窄双峰中孔分布的双中孔ＳｉＯ２材料。实验表明,在所使用的反应体系中,双中孔ＳｉＯ２结构是一种必然的物相,且反应体系的ｐＨ值调节在合成中起决定性作用。当反应体系的ｐＨ值从约９．５增加到１１时,相应产物的孔径分布由双中孔转变为单中孔分布。这些结果为进一步深入理解中孔材料的形成机理提供了新的视野。合成样品用ＸＲＤ和Ｎ２吸附等温线进行了表征。     

介孔分子筛MCM-48的室温合成与表面修饰

在室温条件下的碱性介质中合成了介孔分子筛MCM-48，并对其进行了有机官能团表面修饰。利用HRTEM、低温N₂吸附、XRD、TG、IR和NMR等手段对产物进行了结构和性能分析。实验结果表明，合成产物MCM-48具有规则的孔道结构、大比表面积、大孔容和窄分布的孔径。由硅烷试剂表面修饰后的MCM-48，由于有机官能团接枝在MCM-48的内表面，占据了孔道内部空间，使其比表面积、孔容和孔径都减小。     

Preparation and characterization of highly photoactive nanocrystalline TiO<Subscript>2</Subscript> powders by solvent evaporationinduced crystallization method

Highly photoactive bi-phase nanocrystalline TiO₂ photocatalyst was prepared by a solvent evaporation-induced crystallization (SEIC) method, and calcined at different temperatures. The obtained TiO₂ photocatalyst was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalytic activity was evaluated by the photocatalytic oxidation of acetone in air. The results show that solvent evaporation can promote the crystallization and phase transformation of TiO₂ at 100°C. When calcination temperatures are below 600°C, the prepared TiO₂ powders show bimodal pore size distributions in the mesoporous region. At 700°C, the pore size distributions exhibit monomodal distribution of the inter-aggregated pores due to the collapse of the intra-aggregated pores. At 100°C, the obtained TiO₂ photocatalyst by this method shows good photocatalytic activity, and at 400°C, its photocatalytic activity exceeds that of Degussa P25. This may be attributed to the fact that the prepared TiO₂ photocatalyst has higher specific surface areas, smaller crystallite size and bimodal pore size distribution.     

Synthesis of mesoporous carbons using ordered and disordered mesoporous silica templates and polyacrylonitrile as carbon precursor

Mesoporous carbons were synthesized from polyacrylonitrile (PAN) using ordered and disordered mesoporous silica templates and were characterized using transmission electron microscopy (TEM), powder X-ray diffraction, nitrogen adsorption, and thermogravimetry. The pores of the silica templates were infiltrated with carbon precursor (PAN) via polymerization of acrylonitrile from initiation sites chemically bonded to the silica surface. This polymerization method is expected to allow for a uniform filling of the template with PAN and to minimize the introduction of nontemplated PAN, thus mitigating the formation of nontemplated carbon. PAN was stabilized by heating to 573 K under air and carbonized under N2 at 1073 K. The resulting carbons exhibited high total pore volumes (1.5-1.8 cm3 g(-1)), with a primary contribution of the mesopore volume and with relatively low microporosity. The carbons synthesized using mesoporous templates with a 2-dimensional hexagonal structure (SBA-15 silica) and a face-centered cubic structure (FDU-1 silica) exhibited narrow pore size distributions (PSDs), whereas the carbon synthesized using disordered silica gel template had broader PSD. TEM showed that the SBA-15-templated carbon was composed of arrays of long, straight, or curved nanorods aligned in 2-D hexagonal arrays. The carbon replica of FDU-1 silica appeared to be composed of ordered arrays of spheres. XRD provided evidence of some degree of ordering of graphene sheets in the carbon frameworks. Elemental analysis showed that the carbons contain an appreciable amount of nitrogen. The use of our novel infiltration method and PAN as a carbon precursor allowed us to obtain ordered mesoporous carbons (OMCs) with (i) very high mesopore volume, (ii) low microporosity, (iii) low secondary mesoporosity, (iv) large pore diameter (8-12 nm), and (v) semi-graphitic framework, which represent a desirable combination of features that has not been realized before for OMCs.