Determination of slug permeability factor for pressure drop prediction of slug flow pneumatic conveying

Current models for pressure drop prediction of slug flow pneumatic conveying in a horizontal pipeline system assume some type of steady state conditions for prediction, which limits their capability for increased predictive accuracy relative to experimental data. This is partly because of the nature of slug flow pneumatic conveying system, which, as a dynamic system, never becomes stable. By utilising conservation of mass （airflow）, a dynamic pressure analysis model is proposed on the basis of the derivative of the upstream pressure behaviour. The rate of air permeation through slug, one of the important factors in the conservation model, is expressed as a function of a slug permeability factor. Other factors such as slug velocity, slug length and the fraction of stationary layer were also considered. Several test materials were conveyed in single-slug tests to verify the proposed pressure drop model, showing good agreement between the model and experimental results.     

Pressure drop prediction with a modified frictional-kinetic model for alumina in bypass pneumatic conveying system

A new frictional-kinetic model is proposed and modified for pressure drop prediction of alumina in a bypass pneumatic conveying system. This new model is based on the conventional Johnson–Jackson frictional-kinetic model. The critical value of solids volume fraction and maximum packing limit are modified based on the fluidized bulk density and tapped bulk density, respectively. In addition, an offset solid volume fraction is introduced into the frictional pressure model as well as into the radial distribution functions which represents the correction factors to modify the probability of collisions between particles when solid phase becomes excessively dense. For the application of the model, computational fluid dynamics (CFD) simulations were conducted by using kinetic theory, conventional frictional-kinetic model and modified frictional-kinetic model. The simulation results were then compared with the experimental results. It was found that the modified frictional-kinetic model showed the largest improvement on pressure drop prediction results compared with results obtained from applying the kinetic theory and the conventional frictional-kinetic model, especially for denser flows with low air mass flow rates and high solid loading ratios (SLR). In addition, the solids volume investigation of CFD simulations shows a strong comparison to the actual flow conditions in the pipe, as transient slug type flow of alumina is observed.     

Low-velocity pneumatic conveying in horizontal pipe for coarse particles and fine powders

First,the characteristics of low-velocity conveying of particles having different hardness are experimentally investigated in a horizontal pipeline in terms of flow pattern and pressure drop to show that the slug flow can be classified into two types depending on the settling of particles along the pipeline,and the period is small for slug flow without the settled layer,which is called solitary slug flow.The pressure drop for soft particles is shown to be larger than that for hard particles.Then,experimental results are presented on horizontal fluidized-bed conveying of fine powders to show that air release from the top surface of the conveying channel is an important factor for high mass flow rate of particles.     

Low-velocity pneumatic conveying in horizontal pipe for coarse particles and fine powders

First, the characteristics of low-velocity conveying of particles having different hardness are experimentally investigated in a horizontal pipeline in terms of flow pattern and pressure drop to show that the slug flow can be classified into two types depending on the settling of particles along the pipeline, and the period is small for slug flow without the settled layer, which is called solitary slug flow. The pressure drop for soft particles is shown to be larger than that for hard particles. Then, experimental results are presented on horizontal fluidized-bed conveying of fine powders to show that air release from the top surface of the conveying channel is an imnortant factor for high mass flow rate of particles.     

Simulation of large amplitude waves in a slug tracking scheme compared to roll wave experiments at high pressure

Due to the similarities between large amplitude roll waves and slug flow in two-phase gas–liquid pipe flow, a slug tracking scheme is presented with the addition of a simplified model for roll waves. The waves are treated in a similar way to slugs, modelled as objects moving at the wave velocity and with a pressure variation across them. The two-fluid model is solved on a stationary staggered grid in stratified sections between moving waves and slugs. The model is dynamic meaning that the growth and decay of waves and slugs can be simulated. The wave model implementation within the tracking scheme is discussed and demonstrated in comparison to existing experimental data on wave velocities and averaged pressure drops. The results from the tracking scheme compared well to the experiments when waves were initiated with the experimental frequency. Wave initiation remains as a modelling challenge.     

Correlation of the liquid volume fraction in the slug for horizontal gas-liquid slug flow

Experimental data for gas holdup in liquid slugs are reported for two different pipe sizes (2.58 cm and 5.12 cm I.D.). A simple empirical correlation is developed and is shown to be a significant improvement over the only other published correlation proposed by Hubbard (1965). The results of this investigation are important for the development of a mechanistic model for the prediction of pressure drop and holdup for slug flow in pipes.     

Film thickness measurements in liquid–liquid slug flow regimes

At present there is significant interest in the development of small scale medical diagnostic equipment. These devices offer faster processing times and require smaller sample volumes than equivalent macro scale systems. Although significant attention has been focused upon their outputs, little attention has been devoted to the detailed fluid mechanics that govern the flow mechanisms within these devices. Conventionally, the samples in these small scale devices are segmented into distinct discrete droplets or slugs which are suspended in an organic carrier phase. Separating these slugs from the channel wall is a very thin film of the organic carrier phase.The magnitude of this film is the focus of the present study and the effects of sample slug length and carrier phase fluidic properties on the film are examined over a range of Capillary numbers. A non-intrusive optical technique was used to capture images of the flow from which the magnitude of the film was determined.The experimental results show that the film is not constant along the length of the slug; however above a threshold value for slug length, a region of constant film thickness exists. When compared with existing correlations in the literature, the experimental data showed reasonable agreement with the Bretherton model when the Capillary number was calculated based on the mean two phase flow velocity. However, significant differences were observed when the Capillary number was redefined to account for the mean velocity at the liquid interface, i.e., the mean slug velocity.Analysis of the experimental data revealed that it fell into two distinct flow regimes; a visco-capillary regime and a visco-inertial regime. A modified Taylor expression is presented to estimate the magnitude of the film for flows in the visco-capillary regime while a new model is put forward, based on Capillary and Weber numbers, for flows in the visco-inertial regime. Overall, this study provides some novel insights into parameters, such as aqueous slug length and carrier phase fluidic properties, that affect the thickness of the film in liquid–liquid slug flow regimes.     

栓状流密相气力输送

首先介绍了气力输送的实验设备.评述了水平栓流气力输送的压力降计算方法,用3种不同的方法计算了压力降并与实验数据进行比较.此外评述了用特征线方法进行水平管的数值模拟,倾斜管的压力降计算和长距离的栓流气力输送.最后展望了该领域的发展方向.      

Two-fluid model for transient analysis of slug flow in oil wells

In this work it is presented a transient, one-dimensional, adiabatic model for slug flow simulation, which appears when liquid (mixture of oil and water) and gas flow simultaneously through pipes. The model is formed by space and time averaged conservation equations for mass, momentum and energy for each phase, the numerical solution is based on the finite difference technique in the implicit scheme. Velocity, pressure, volumetric fraction and temperature profiles for both phases were predicted for inclination angles from the horizontal to the vertical position (unified model) and ascendant flow. Predictions from the model were validated using field data and ten correlations commonly used in the oil industry. The effects of gas heating or cooling, due to compression and expansion processes, on the predictions and numerical stability, were studied. It was found that when these effects are taken into account, a good behavior of temperature predictions and numerical stability are obtained. The model presents deviations lower than 14% regarding field data and it presents better predictions than most of the correlations.     

Pressure drop in two phase slug/bubble flows in mini scale capillaries

A segmented two phase slug/bubble flow occurs where a liquid and a gas are pumped into the same tube over a range of Reynolds numbers. This segmented two phase flow regime is accompanied by an increase in pressure drop relative to the single phase flow where only one fluid is flowing in a capillary. This work experimentally and theoretically examines the pressure drop encountered by the slug/bubble flow with varying slug lengths in mini channels. In the experimental work the dimensionless parameters of Reynolds number and Capillary number span over three orders of magnitude, and dimensionless slug length ranges over two orders of magnitude to represent flows typical of mini- and micro-scale systems. It is found, in agreement with previous work, that these dimensionless groups provide the correct scaling to represent the pressure drop in two phase slug/bubble flow, although the additional pressure drop caused by the interface regions was found to be ∼40% less than previously reported.     

Towards the numerical simulation of the horizontal slug front

Steps towards the numerical simulation of the flow behind the slug front in horizontal slug flow performed with a streamfunction-vorticity representation of the mean flow and an energy dissipation model for the turbulence are discussed. The flow field consists of two vortices, one saddle point and four stagnation regions. Attention is focused on the following boundary conditions: moving wall jet, moving wall, free jet velocity discontinuity and vertical liquid-gas open surface. A dissipation flux boundary condition is suggested to simulate the interaction of the turbulent eddies with the open surface. A method to assess the necessity to use a transport model equation for the dissipation rather than a geometric specification of a length is suggested. Three different ways to characterize the mixing zone length are proposed.     

水平管道气固两相分层流动过程的研究

以空气作为输送动力、粉煤灰及玻璃微珠作为输送物料,对气力输送管道中气固两相流的流动特性进行了系统的试验研究.对管路系统的特性、操作条件、物料和气体的性质等影响气固两相流压力损失的主要因素进行了探讨.并在实验的基础上对两相流动的沉积速度、经济速度进行了确定.同时在对粉体受力分析的基础上建立了分层流动的物理及数学模型,通过对比数学模型计算值与试验值得出该数学模型具有一定的计算精度,能够用于指导分层流动的研究及应用.     

垂直上升管内油—气—水三相弹状流压力降的研究

给出一种垂直上升油－气－水三相弹状流压力降的计算模型。该模型考虑弹状流中Ｔａｙｌｏｒ气泡周围下降液膜的变化历程。通过油－气－水弹状流的实验研究发现，该模型的数值模拟结果与低压工况下的实验值符合得较好。本模型是计算垂直油－气－水三相弹状流中液相的连续相为水相时的压力降的有效方法。     

Lagrangian slug flow modeling and sensitivity on hydrodynamic slug initiation methods in a severe slugging case

Severe slugging is a dynamic two-phase flow phenomenon with regular liquid accumulation and blow-out in flow-line riser geometries. This paper discusses the applicability of a slug tracking model on a case where hydrodynamic slug initiation in a horizontal part of the pipeline upstream the riser base affects the severe slugging cycle period. The given experimental case is from the Shell laboratories in Amsterdam: air–water flow in a 100 m long pipe (65 m horizontal and 35 m −2.54° downwards) followed by a 15 m long vertical riser.A Lagrangian slug and bubble tracking model is described. A two-fluid model is applied in the bubble region and the slug region is treated as incompressible flow, with an integral momentum equation. Slug initiation from unstable stratified flow can be captured directly by solving the two-fluid model on a fine grid (a hybrid capturing and tracking scheme). Alternatively, slug initiation can be made from sub grid models, allowing for larger grid sizes. The sub grid models are based on the two established flow regime transition criteria derived from the stability of stratified flow and from the limiting solution of the unit cell slug flow model.Sensitivity studies on hydrodynamic slug initiation models on the severe slugging characteristics are presented. No hydrodynamic slug initiation (e.g. large grid size in the capturing scheme) overestimates the severe slug period compared with the experiments. Slug capturing and sub grid initiation models both give good predictions for small grid sizes (provided the detailed inlet configuration is included in the capturing case). Good predictions are also shown for larger grid sizes (factor of 50) and sub grid initiation models.The numerical tests show that correct prediction of the severe slugging cycle is sensitive to the initiation of upstream hydrodynamic slugs, but less sensitive to the local structure of the slug flow (frequencies and lengths) in the upstream region.     

Gas/shear-thinning liquid flows through pipes: Modeling and experiments

In chemical and oil industry gas/shear-thinning liquid two-phase flows are frequently encountered. In this work, we investigate experimentally the flow characteristics of air/shear-thinning liquid systems in horizontal and slightly inclined smooth pipes. The experiments are performed in a 9-m-long glass pipe using air and three different carboxymethyl cellulose (CMC) solutions as test fluids. Flow pattern maps are built by visual observation using a high-speed camera. The observed flow patterns are stratified, plug, and slug flow. The effects of the pipe inclination and the rheology of the shear-thinning fluid in terms of flow pattern maps are presented. The predicted existence region of the stratified flow regime is compared with the experimental observation showing a good agreement. A mechanistic model valid for air/power-law slug flow is proposed and model predictions are compared to the experimental data showing a good agreement. Slug flow characteristics are investigated by the analysis of the signals of a capacitance probe: slug velocity, slug frequency, and slug lengths are measured. A new correlation for the slug frequency is proposed and the results are promising.     

One-way coupled fluid–structure interaction of gas–liquid slug flow in a horizontal pipe: Experiments and simulations

Pipelines conveying a multiphase mixture must withstand the cyclic induced stresses that occur due to the alternating motion of gas pockets and liquid slugs. Few previous studies have considered gas–liquid slug flow and the associated fluid–structure interaction problems. In this study, experimental and numerical techniques were adopted to simulate and analyze the two-phase slug flow and the associated stresses in the pipe structure. In the numerical simulation, a one-way coupled fluid–structure framework was developed to explore the slug flow interaction with a horizontal pipe assembly under various superficial gas and liquid velocities. A modified Volume of Fluid and finite element methods were utilized to model the fluid and structure domains. The file-based coupling technique was adopted to execute the coupling mechanism. By contrast, slug characteristics were measured experimentally, while Bi-axial strain gauges were used to capture time-varying strain signals. Excellent agreements between the predicted and measured stress results were achieved with a maximum error of 10.2 %. It was found that at constant superficial liquid velocity, the maximum induced stresses on the pipe wall increased with increasing the slug length and slug velocity. While for the slug frequency, the maximum principal stresses decreased with increasing the slug frequency.     

Numerical modeling of slug flow initiation in a horizontal channels using a two-fluid model

This paper presents a methodology for modeling slug initiation and growth in horizontal ducts. Transient two-fluid equations are solved numerically using a class of high-resolution shock capturing methods. The advantage of this method is that slug formation and growth in a stratified regime can be calculated directly from the solutions to the flow field differential equations. In addition, by using high-resolution shock capturing methods that do not contain numerical diffusion, the discontinuity generated by slugging in the flow field can be modeled with good accuracy. The two-fluid model is shown to be well-posed mathematically only under certain conditions. Under these circumstances, the two-fluid model is capable of correctly predicting and modeling the flow physics. When ill-posed, an unbounded instability occurs in the flow field solution, and the instability amplitude increases exponentially with decreasing mesh sizes. This work shows that there are three zones associated with slug formation. In addition, long wavelength slugs are shown to initiate from short wavelength waves. These short waves are generated at the interface of the two phases by the Kelvin-Helmholtz hydrodynamic instability. The results obtained through numerical modeling show good agreement with experimental results.     

Void fraction measurement of bubble and slug flow in a small channel using the multivision technique

Using the multivision technique, a new void fraction measurement method was developed for bubble and slug flow in a small channel. The multivision system was developed to obtain images of the two-phase flow in two perpendicular directions. The obtained images were processed—using image segmentation, image subtraction, Canny edge detection, binarization, and hole filling—to extract the phase boundaries and information about the bubble or slug parameters. With the extracted information, a new void fraction measurement model was developed and used to determine the void fraction of the two-phase flow. The proposed method was validated experimentally in horizontal and vertical channels with different inner diameters of 2.1, 2.9, and 4.0 mm. The proposed method of measuring the void fraction has better performance than the methods that use images acquired in only one direction, with a maximum absolute difference between the measured and reference values of less than 6%.     

Characterization of the gas pulse frequency, amplitude and velocity in non-steady dense phase pneumatic conveying of powders

Current modelling techniques for the prediction of conveying line pressure drop in low velocity dense phase pneumatic conveying are largely based on steady state analyses.Work in this area has been on-going for many years with only marginal improvements in the accuracy of prediction being achieved.Experimental and theoretical investigations undertaken by the authors suggest that the flow mechanisms involved in dense phase conveying are dominated by transient effects rather than those of steady state and are possibly the principal reasons for the limited improvement in accuracy.This paper reports on investigations on the pressure fluctuation behaviour in dense phase pneumatic conveying of powders.The pressure behaviour of the gas flow in the top section of the pipeline was found to exhibit pulsatile oscillations.In particular,the pulse velocity showed variation in magnitude while the frequency of the oscillations rarely exceeded 5 Hz.A wavelet analysis using the Daubechie 4 wavelet found that the amplitude of the oscillations increased along the pipeline.Furthermore,there was significant variation in gas pulse amplitude for different types of particulate material.     

Holdup of the liquid slug in two phase intermittent flow

A physical model for the prediction of gas holdup in liquid slugs in horizontal and vertical two phase pipe slug flow is presented. This model can also be used to yield the transition between elonganted bubbles and slug flow within the intermittent flow pattern. In addition a previously published model for predicting the stable slug length in vertical upward slug flow (Taitel et al. 1980) is extended here for the case of horizontal slug flow.