β-环糊精存在下阳离子表面活性剂的毛细管电泳电导法测定

基于H3 BO3 与 β CD配合成大阴离子 ,与不同的阳离子表面活性剂作用不同 ,建立了快速分离检测阳离子表面活性剂的毛细管电泳电导法。研究了H3 BO3 与 β CD的浓度 ,缓冲液的酸度和浓度对分离的影响。在优化的实验条件下 ,溴化四丁基铵 (TBAB)、溴化十二烷基三甲基铵 (DTAB)、溴化十六烷基三甲基铵(CTMAB)阳离子表面活性剂 10min内完全分离 ,峰形良好。线性范围分别为TBAB 10 -3 ～ 10 -5mol/L ,DTAB1.0× 10 -3 ～ 5 .0× 10 -6mol/L ,CTMAB 1.0× 10 -3 ～ 5 .0× 10 -6mol/L。检测限分别为TBAB 7.5× 10 -6mol/L ,DTAB 1.7× 10 -6mol/L ,CTMAB 1.0× 10 -6mol/L。方法用于合成水样分析 ,结果令人满意     

黄芩及其制剂中黄芩素和黄芩甙的

用毛细管区带电泳 -电化学检测法测定了黄芩及其制剂中黄芩素和黄芩甙的含量。研究了电极电位、电解液酸度和浓度、电泳电压及进样时间等对电泳的影响 ,得到了较为优化的测定条件。以直径为300μm的碳圆盘电极为检测电极 ,电极电位为0.90V(vsSCE) ,在100mmol/L硼酸盐缓冲液(pH9.0)中 ,上述两组分在8min内完全分离。黄芩素和黄芩甙浓度与电泳峰电流分别在5.0×10 -7～1.0×10 -3mol/L和1.0×10 -6～1.0×10 -3mol/L范围内呈良好线性 ,检出限分别为2.24×10 -7mol/L和5.48×10 -7mol/L。7次测定分别含5.0×10 -4mol/L黄芩素和黄芩甙试样溶液 ,峰高的相对标准偏差分别为3.53%和4.03%。     

手性药物心得安对映体的毛细管电泳/电化学分离检测研究

报道了采用毛细管电泳 -方波安培检测法对手性药物对映体———外消旋心得安进行了分离检测研究。以5mmol/LNaOH -8mmol/L柠檬酸 -10mmol/Lβ_CD(pH4.5)为电泳介质 ,未涂层熔融石英毛细管(75μm×45cm)为分离通道 ,分离电压 +12.5kV ,实现了心得安对映体的基线分离。方法的线性范围为2.0×10 -6～1.0×10 -4mol/L ,检出限为5.0×10 -7mol/L。     

NDA柱前衍生毛细管电泳高灵敏安培检测组胺

本文提出了毛细管电泳 2,3 萘二甲醛(NDA)柱前衍生高灵敏安培检测组胺的新方法,对衍生反应条件和电泳分析条件,包括衍生试剂浓度、衍生溶液的pH值、衍生反应时间、分离介质的pH值、进样时间和分离电压进行了优化,确定衍生溶液pH值为9.0,NDA浓度为5.0×10-4mol/L,CN-浓度为2.5×10-3mol/L时的衍生效果最佳;10mmol/LTris H3PO4(pH5.0)为最佳电泳缓冲液,检测电位为0.7V(vs.SCE)时,组胺检出限达6.8×10-8mol/L(S/N=3),较不衍生测定法灵敏度提高6倍,为测定痕量组胺提供了一个新方法。     

沙棘黄酮口服液中芦丁和5-羟色胺的毛细管区带电泳电化学检测

建立了毛细管区带电泳 -电化学检测法 (CE -ED)测定芦丁和5_羟色胺含量的方法 ,研究了电极电位、运行缓冲液的酸度和浓度、电泳电压及进样时间等因素对分离检测的影响,确定了最佳测定条件 ;以直径为300μm的碳圆盘电极为检测电极,电极电位为0.90V(vsSCE),在50mmol/L硼酸盐缓冲液(pH8.5)中,上述2组分在12min内完全分离 ,被分析物的电流响应与浓度在约3个数量级范围内呈良好线性关系,检出限分别为3×10-7 mol/L和8×10-8 mol/L ,7次测定含5.0×10-4 mol/L的芦丁和5_羟色胺的标准溶液,峰高的相对标准偏差分别为2.5 %和3.8 % ;该法成功地用于中药沙棘黄酮口服液中芦丁和5_羟色胺的测定     

毛细管电泳电化学检测法测定胡黄连中香草酸和阿魏酸的含量

采用毛细管电泳电化学检测法测定了胡黄连中香草酸和阿魏酸的含量 ;研究了电极电位、运行缓冲液的浓度和酸度、电泳电压及进样时间等对电泳的影响 ,得到了最优化的测定条件 ;以直径为300μm的碳圆盘电极为检测电极 ,工作电极电位为0.8V(vs.SCE) ,在50mmol/L硼砂(pH8.4)运行缓冲液中 ,上述两组分在8min内完全分离 ;香草酸和阿魏酸线性范围分别为5×10-4～1×10-6 mol/L和1×10-3～1×10-6 mol/L ,检出限分别为4.2×10 -7和3.0×10 -7mol/L ;7次平行进样的相对标准偏差(RSD)为2.2 %和2.8 % ,回收率(n=3)分别为99%和103 % ,该法灵敏可靠 ,结果令人满意。     

散利痛中扑热息痛和异丙基安替比林的毛细管区带电泳电化学检测法测定

毛细管区带电泳 -电化学检测法同时测定散利痛片中有效成分扑热息痛和异丙基安替比林的含量 ;研究了电极电位、电解液浓度和酸度、电泳电压及进样时间等对电泳的影响 ,得到了最优化的测定条件 ;以直径为300μm的碳圆盘电极为检测电极 ,工作电极电位为1.0V(vsSCE) ,在50mmol/L硼砂 -NaOH(pH9.35)运行缓冲液中 ,上述两组分在8min内完全分离 ;扑热息痛和异丙基安替比林线性范围分别为2×10-3～5×10 -6mol/L和2×10 -3～2×10 -6mol/L,检出限分别为5×10 -6mol/L和2×10 -6mol/L ;7次平行进样的相对标准偏差(RSD)为3.5%和1.8 % ,加标回收率(n=3)分别为101 %和98% ,该法灵敏可靠 ,结果令人满意。     

毛细管电泳-电化学检测测定茶叶中咖啡因、表儿茶素和抗坏血酸

高效毛细管电泳电化学检测同时测定了6种茶叶中的咖啡因、表儿茶素和抗坏血酸的含量,考察了实验参数对分离、检测的影响。在最佳实验条件下,以300 靘直径的碳圆盘电极为检测电极,检测电极为1.20 V(vs.SCE),在25 mmol/L硼酸盐25 mmol/L磷酸盐(pH 7.6)的混合运行缓冲液中,上述各组分在16 min内能完全分离。咖啡因、表儿茶素和抗坏血酸在2×10-3mol/L～１×10-5 mol/L、5×10-5mol/L～5×10-7mol/L、2×10-4 mol/L～1×10-5mol/L范围内呈线性关系,检测下限分别为6×10-6mol/L、4×10-7mol/L和1×10-6mol/L。该法直接用于茶叶中咖啡因、表儿茶素和抗坏血酸的测定,结果令人满意。     

联萘酚对映体的毛细管电泳/方波安培法分离检测

建立了毛细管电泳/方波安培法分离检测联萘酚对映体的新方法.对影响对映体分离度的影响因素,如手性选择剂β 环糊精浓度、氢氧化钠浓度、硼酸浓度、分离电压进行了探讨。在16mmol/L氢氧化钠+14mmol/Lβ 环糊精+4mmol/L硼酸的电泳运行液,方波平衡电位+0.90V和10kV的分离电压条件下,联萘酚对映体在10min内得到基线分离,检出限为1.0×10-6mol/L。     

电泳中介微分析法测定铁(Ⅱ)和铜(Ⅱ)

利用电泳中介微分析通过与邻菲罗啉的络合反应完成了对Fe2+与Cu2+的同时测定。在压差作用下,淌度较小的邻菲罗啉在金属离子区带之前首先进样,加高电压后,两区带电泳在磷酸缓冲液中 (pH=4. 5)混合、反应形成络合物并实现电泳分离。研究了缓冲液pH、试剂和样品区带长度对分离效果的影响。对于Fe2+与Cu2+两离子,方法的检出限(S/N=3)分别为 1. 6和 11μmol/L;线性范围分别为 5. 0×10-6 ~3. 0×10-4 mol/L(r=0. 9979)和 8. 0×10-5 ~3. 0×10-4 mol/L(r=0. 9996)。采用标准矿样验证了测定Fe2+的可行性。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.