Physics-based modeling for fretting behavior of nominally flat rough surfaces

A physics-based modeling approach for fretting behavior of nominally flat rough contact is proposed. This approach employs physics-based models for partial slip of spherical contacts to formulate the contact forces at asperity tips. The individual asperity forces are added by a statistical method to obtain the fretting response of a flat rough contact. This approach suggests the plasticity index as an important parameter for studying the surface roughness effects on fretting. Fretting responses obtained by one of the models favorably compare with experimental results obtained from bolted steel lap joints. Tangential stiffness and energy loss per cycle obtained from the experiments and the model predictions deviate at higher preloads. This discrepancy is due to limitations of the modeling approach in accounting for plastic response to tangential loading.     

基于Iwan模型的接合面切向响应建模

针对工程中常见预紧力作用下的搭接接头,研究其在小幅切向位移激励时的切向位移响应问题,为此提出一种新的基于实际表面形貌和材料性能参数的滑移力密度分布函数.应用该分布函数得到搭接接头切向响应本构模型,并获得单位加载周期内的迟滞曲线和能量耗散值, 通过与已出版的实验结果相对比,发现得到的模拟值与实验结果吻合, 证明该模型的合理性.在此基础上利用该分布函数研究了接合面切向位移与切向力、切向接触刚度及能量耗散之间的关系,结果表明: 建立的模型能很好地描述接合面间切向力与切向位移之间的关系,临界滑移力函数开始迅速上升, 到达最大值后迅速收敛到零;切线力与切向位移之间表现出非线性特性, 随着切向位移的增大,切向接触刚度表现出"软化"现象;初始切向刚度与法向载荷、粗糙度参数及塑性指数有关, 对于确定的接触表面,法向力越大, 初始切向刚度越大; 初始切向刚度同样也随着塑性指数的增大而增大.      

机械结合面切向接触阻尼计算模型

针对两粗糙表面在法向力和切向力共同作用下相互接触时结合面切向阻尼的问题进行了研究。首先,根据KE模型对单个微凸体在弹性、弹塑性、塑性变形阶段的切向接触行为进行了分析,获得了微凸体在三个变形阶段的黏滑特性;然后,基于GW统计模型建立了一种在微凸体法向弹性、弹塑性和塑性变形机制基础上,考虑微凸体黏滑摩擦行为的机械结合面切向接触阻尼统计模型;最后,分别讨论了机械结合面的法向预载荷、切向激振频率和切向动态位移幅值对机械结合面切向阻尼的影响。研究表明:结合面切向接触阻尼系数随着结合面法向载荷的增大而增大,随着切向激振频率和切向动态位移幅值的增大而减小;在高频率、大幅值下,结合面切向接触阻尼系数几乎与动态位移幅值和激振频率无关。为了验证模型的准确性,构建了动态切向力作用下的结合面切向阻尼试验,其试验结果与理论仿真变化规律与量级基本一致,从而证明了本文所提出的切向阻尼模型的有效性。      

Stabilized interface methods for mechanical joints: Physics-based models and variationally consistent embedding

This paper presents the application of a new method for interfacial modeling utilizing a merger of continuous Galerkin and discontinuous Galerkin concepts to simulate the behavior of mechanical joints. The interfacial flux terms arising naturally from the discontinuous Galerkin treatment provide a mechanism to embed friction models in a variationally consistent fashion. Due to the unbiased implementation of the interface, facilitated by avoiding the master–slave concept, the deformation of the two interacting surfaces conforms to the local material and geometric attributes of the surfaces. This results in a better preservation of physics in interface mechanics. Additionally, the method is incorporated into a Variational Multiscale framework that comes equipped with a built-in error estimation module, providing numerical estimation of convergence and distinguishing discretization errors from modeling errors. A series of quasi-static numerical simulations of a lap joint under fretting conditions are conducted to compare the performance of two friction models: (i) classical Coulomb friction model and (ii) physics-based multiscale model. Hysteresis study of a three-dimensional double-bolted lap joint for the two friction models is also presented and the computed results are shown to be consistent between conforming and nonconforming meshes.     

考虑节点损伤的钢框架结构分析模型

钢框架结构在强震作用下将进入非线性状态,结构的刚度和强度等力学性能随之降低,从而影响到结构以后的抗震性能.本文利用断裂力学的基本原理,通过对栓焊节点存在焊缝裂纹的钢框架刚性连接节点的分析,推导了裂纹的有效长度和有效深度,获得了有损伤刚性连接节点的M-θ关系;并推导了节点有损伤的梁单元刚度矩阵.在数值计算的基础上分析了节点刚度变化对框架结构内力的影响,结果表明节点损伤对结构内力分析影响显著,对有损伤钢框架结构进行承载力评估时必须考虑节点损伤的影响.     

二硫化钼粘结固体润滑涂层的径向和切向微动损伤的比较研究

通过径向和切向微动试验考察了二硫化钼粘结固体润滑涂层的微动摩擦学特性 ,并利用扫描电子显微镜、能量色散谱和X射线光电子能谱等分析了两类微动损伤区的微观特征 .结果表明 :二硫化钼粘结固体润滑涂层具有良好的抗径向微动损伤性能 ;切向微动条件下无混合区存在 ,涂层损伤强烈依赖于位移幅值 ,并伴随MoS2 的氧化 ;径向微动损伤呈现切向微动部分滑移区的特征     

两种典型螺栓连接结构的刚度特性比较研究

针对法兰对接和径向套接两种典型舱段螺栓连接形式,基于有限元静刚度计算、动力学简化建模、冲击响应特性分析及结构冲击试验,系统研究了两种连接形式的轴向刚度特性及其对动力学冲击响应的影响.有限元静刚度分析揭示了法兰对接与径向套接的轴向拉压刚度分别是非对称的和对称的,而法兰对接的平均刚度更大.之后,为两种连接形式建立了统一的动力学模型,证明非对称的轴向拉压刚度导致结构在受到横向载荷作用时会产生附加的耦合轴向振动,并且利用高精度幂函数拟合刚度跳变,得到耦合轴向振动频率是弯曲振动频率的二倍的结论.最后,通过冲击动力学试验证明了法兰对接存在二倍频的耦合轴向振动,而径向套接则不存在该耦合振动.径向套接虽然一阶频率较低,但阻尼效果更好.     

柔性铰柔性杆机器人动力学建模、仿真和控制

本文探究了铰柔性对机器人动力学响应和动力学控制的影响. 首先, 建立由$n$个柔性铰和$n$个柔性杆组成的空间机器人模型, 运用递推拉格朗日动力学方法, 得到柔性机器人系统的刚柔耦合动力学方程. 在动力学建模过程中, 除了考虑杆件的拉伸变形、弯曲变形、扭转变形以及非线性耦合变形对机器人系统动力学行为的影响, 还考虑了铰的柔性对机器人动力学响应和控制的影响. 其中, 柔性铰模型是基于Spong的柔性关节简化模型, 将柔性铰看成线性扭转弹簧, 不仅考虑了铰阻尼的存在, 还考虑了柔性铰的质量效应. 其次, 编写了空间柔性铰柔性杆机器人仿真程序, 研究铰的刚度系数和阻尼系数对系统动力学响应的影响. 研究表明: 随着柔性铰刚度系数的增大, 柔性机器人的动态响应幅值减小, 振动频率变大. 随着柔性铰阻尼系数的增大, 柔性机器人的动态响应幅值减小, 振动幅值的衰减速度变快. 可通过调节柔性铰的刚度和阻尼来减小柔性铰柔性杆机器人的振动, 因此铰阻尼的研究具有重要工程意义. 最后, 研究了铰柔性在机器人系统动力学控制中的影响. 在刚性铰机械臂和柔性铰机械臂完成相同圆周运动时, 通过逆动力学方法求解得到两种情况下的关节驱动力矩. 研究表明: 引入柔性铰会使控制所需的驱动力矩变小, 对机器人控制的影响显著.      

DYNAMICS MODELING,SIMULATION, AND CONTROL OF ROBOTS WITH FLEXIBLE JOINTS AND FLEXIBLE LINKS$^{\bf 1)}$

本文探究了铰柔性对机器人动力学响应和动力学控制的影响. 首先, 建立由$n$个柔性铰和$n$个柔性杆组成的空间机器人模型, 运用递推拉格朗日动力学方法, 得到柔性机器人系统的刚柔耦合动力学方程. 在动力学建模过程中, 除了考虑杆件的拉伸变形、弯曲变形、扭转变形以及非线性耦合变形对机器人系统动力学行为的影响, 还考虑了铰的柔性对机器人动力学响应和控制的影响. 其中, 柔性铰模型是基于Spong的柔性关节简化模型, 将柔性铰看成线性扭转弹簧, 不仅考虑了铰阻尼的存在, 还考虑了柔性铰的质量效应. 其次, 编写了空间柔性铰柔性杆机器人仿真程序, 研究铰的刚度系数和阻尼系数对系统动力学响应的影响. 研究表明: 随着柔性铰刚度系数的增大, 柔性机器人的动态响应幅值减小, 振动频率变大. 随着柔性铰阻尼系数的增大, 柔性机器人的动态响应幅值减小, 振动幅值的衰减速度变快. 可通过调节柔性铰的刚度和阻尼来减小柔性铰柔性杆机器人的振动, 因此铰阻尼的研究具有重要工程意义. 最后, 研究了铰柔性在机器人系统动力学控制中的影响. 在刚性铰机械臂和柔性铰机械臂完成相同圆周运动时, 通过逆动力学方法求解得到两种情况下的关节驱动力矩. 研究表明: 引入柔性铰会使控制所需的驱动力矩变小, 对机器人控制的影响显著.     

微动白层形成的控制因素及其对磨损过程的影响

在径向和复合(切向与径向复合)微动条件下，考察了2091铝锂合金在不同载荷水平和倾斜角度下的微动行为和损伤过程；结合不同阶段微动磨痕剖面分析，研究了微动白层(TTS)的形成条件，并详细分析了在不同微动阶段TTS的演变过程．结果表明，TTS形成的主要控制因素是表面切应力和切向位移，TTS形成过程呈现塑性变形特征；TTS对磨损过程具有重要影响．     

Study of the effect of contact force model on the dynamic response of mechanical systems with dry clearance joints: computational and experimental approaches

The main objective of this work is to present a computational and experimental study on the contact forces developed in revolute clearance joints. For this purpose, a well-known slider-crank mechanism with a revolute clearance joint between the connecting rod and slider is utilized. The intra-joint contact forces that are generated at these clearance joints are computed by considering several different elastic and dissipative approaches, namely those based on the Hertz contact theory and the ESDU tribology-based cylindrical contacts, along with a hysteresis-type dissipative damping. The normal contact force is augmented with the dry Coulomb’s friction force. In addition, an experimental apparatus is used to obtained some experimental data in order to verify and validate the computational models. From the outcomes reported in this paper, it is concluded that the selection of the appropriate contact force model with proper dissipative damping plays a significant role in the dynamic response of mechanical systems involving contact events at low or moderate impact velocities.     

一种机械结构结合面动力学参数识别方法

机械结构结合面刚度和阻尼的确定是对结构进行动态分析和优化设计的关键问题之一。本文提出一种结合面动力学参数识别方法。该方法通过实测结构少量几个点上的振型和传递函数确定结合面参数。它不要求预先建立结构各部件的解析模型,也不需要实测整个结构完整的动态信息,因此适用于复杂结构结合面动力学参数的识别。文章阐明了结合面参数的识别原理,并讨论了如何消除实验误差对识别结果的影响。用本文方法识别了一台钻床的结合面参数,得到了令人满意的结果。     

Physics-based modeling for partial slip behavior of spherical contacts

A physics-based modeling approach for partial slip behavior of a spherical contact is proposed. In this approach, elastic and elastic–plastic normal preload and preload-dependent friction coefficient models are integrated into the Cattaneo–Mindlin partial slip solution. Partial slip responses to cyclic tangential loading (fretting loops) obtained by this approach are favorably compared with experiments and finite element results from the literature. In addition to load-deformation curves, tangential stiffness of the contact and energy dissipation per fretting cycle predictions of the models are also provided. Finally, the critical assumptions of elastically similar bodies, smooth contact surface and negligible adhesion, and limitations of this physics-based modeling approach are discussed.     

作大范围回转运动柔性梁斜碰撞动力学研究

为正确估计由于碰撞引起的多柔体系统动力学特性的变化,针对作大范围回转运动的柔性梁与一固定斜面发生斜碰撞的情况,在考虑刚柔耦合效应的多柔体系统动力学建模理论的基础上,利用假设模态法建立起重力场作用下的柔性梁一致线性化动力法向碰撞过程中系统的动力行为。基于Ｈｅｒｔｚ接触理论和非线性阻尼项建立法向碰撞接触模型,基于线性切向接触刚度建立柔性梁切向碰撞接触模型,提出的数值算法保证了计算结果的合理性,给出的仿     

固-液结合面法向动态接触刚度及阻尼的理论模型与实验分析

固-液接触状态广泛存在于机床核心单元关键零部件的接触运动副中,精确获得固-液结合面法向接触刚度及阻尼参数是高档数控机床产品在研发阶段就存在的一个关键理论与技术问题,并且仍然尚未根本解决.固-液结合面在介观层面上表现为两个粗糙表面的接触,在微观层面上表现为微凸体之间的接触,并在中/重载荷作用下微凸体可能会发生弹性/弹塑性...     

Dynamic analysis of planar rigid-body mechanical systems with two-clearance revolute joints

In this paper, the behavior of planar rigid-body mechanical systems due to the dynamic interaction of multiple revolute clearance joints is numerically studied. One revolute clearance joint in a multibody mechanical system is characterized by three motions which are: the continuous contact, the free-flight, and the impact motion modes. Therefore, a mechanical system with n-number of revolute clearance joints will be characterized by 3 ⁿ motions. A slider-crank mechanism is used as a demonstrative example to study the nine simultaneous motion modes at two revolute clearance joints together with their effects on the dynamic performance of the system. The normal and the frictional forces in the revolute clearance joints are respectively modeled using the Lankarani–Nikravesh contact-force and LuGre friction models. The developed computational algorithm is implemented as a MATLAB code and is found to capture the dynamic behavior of the mechanism due to the motions in the revolute clearance joints. This study has shown that clearance joints in a multibody mechanical system have a strong dynamic interaction. The motion mode in one revolute clearance joint will determine the motion mode in the other clearance joints, and this will consequently affect the dynamic behavior of the system. Therefore, in order to capture accurately the dynamic behavior of a multi-body system, all the joints in it should be modeled as clearance joints.     

Design of a one-dimensional flexible structure for desired load-bearing capability and axial displacement

A flexible spine is capable of bearing both transverse and axial external loads. At the same time, it is observed in animals that the spine deforms substantially during their motion and this allows the body to move e?ciently and achieve high speeds. This paper deals with the modeling and design of one-dimensional flexible objects for a desired load-carrying capability and axial deflection. The flexible one-dimensional object is modeled as a serial chain of rigid segments connected by one-degree-of-freedom rotary joints with torsional springs and dampers at the joints. For a desired transverse and axial loading, optimization techniques are used to obtain the values of orientation of the rigid segments, the joint stiffness and damping, which gives the desired axial displacement and the shape. It is shown that changing the orientation or the shape of the one-dimensional structure has more effect than changing the stiffness at the joints. Various types of loading and axial deflections are considered and the optimization procedure is illustrated through numerical examples. The response of such a flexible structure to a transient periodic loading is also obtained.     

Numerical and experimental investigation on multibody systems with revolute clearance joints

A comprehensive combined numerical and experimental study on the dynamic response of a slider-crank mechanism with revolute clearance joints is presented and discussed in this paper to provide an experimental verification and validation of the predictive capabilities of the multibody clearance joint models. This study is supported in an experimental work in a test rig, which consists of a slider-crank mechanism with an adjustable radial clearance at the revolute joint between the slider and the connecting rod. The motion of the slider is measured with a linear transducer and an accelerometer. Dynamic tests at different operating crank speeds and with several clearance sizes are performed. The maximum slider acceleration, associated with the impact acceleration, is used as a measure of the impact severity. The obtained results demonstrate the dynamical behavior of a multibody mechanical system with a clearance joint. Finally, the correlation between the numerical and experimental results is presented and discussed leading to validated models of clearance revolute joints.     

Spatial rigid-multibody systems with lubricated spherical clearance joints: modeling and simulation

The dynamic modeling and simulation of spatial rigid-multibody systems with lubricated spherical joints is the main purpose of the present work. This issue is of paramount importance in the analysis and design of realistic multibody mechanical systems undergoing spatial motion. When the spherical clearance joint is modeled as dry contact; i.e., when there is no lubricant between the mechanical elements which constitute the joint, a body-to-body (typically metal-to-metal) contact takes place. The joint reaction forces in this case are evaluated through a Hertzian-based contact law. A hysteretic damping factor is included in the dry contact force model to account for the energy dissipation during the contact process. The presence of a fluid lubricant avoids the direct metal-to-metal contact. In this situation, the squeeze film action, due to the relative approaching motion between the mechanical joint elements, is considered utilizing the lubrication theory associated with the spherical bearings. In both cases, the intra-joint reaction forces are evaluated as functions of the geometrical, kinematical, and physical characteristics of the spherical joint. These forces are then incorporated into a standard formulation of the system’s governing equations of motion as generalized external forces. A spatial four bar mechanism that includes a spherical clearance joint is considered here as an example. The computational simulations are carried out with and without the fluid lubricant, and the results are compared with those obtained when the system is modeled with perfect joints only. From the general results, it is observed that the system’s performance with lubricant effect presents fewer peaks in the kinematic and dynamic outputs, when compared with those from the dry contact joint model.     

考虑微观粘滑的连接梁结构动力响应分析

连接的存在对结构的动力学响应有重要影响.界面的微观/宏观粘滑运动引起结构刚度和阻尼的非线性.传统的结构动力学研究中通常采用等效线性化的方式处理含连接结构的动响应分析问题.本文从连接界面微/宏观滑移运动引起结构非线性和阻尼迟滞的物理机理出发,利用一种弹簧-滑块并联系统模型模拟界面上的微/宏观粘滑行为,以该模型描述的本构关系为基础,推导了能应用于平面梁结构有限元动响应分析的非线性连接单元.利用上述模型和单元研究了含连接平面梁结构的动响应问题.设计了实验件,进行了力锤冲击实验,并将数值计算结果与实验结果进行了对比和分析.结果表明,界面微/宏观粘滑是引起干摩擦阻尼的主要原因,考虑非线性微/宏观粘滑运动对含连接结构的动响应分析至关重要.本文的模型和方法能够有效地预测含连接结构的非线性动力学响应,特别是在瞬态响应的高振幅阶段.