Electrochemical properties of LiFePO4-multiwalled carbon nanotubes composite cathode materials for lithium polymer battery

LiFePO₄-multiwalled carbon nanotubes (MWCNTs) composites were prepared by a hydrothermal method followed by ball-milling and heat treating. Cyclic voltammetry, ac impedance and galvanostatic charge/discharge testing results indicate that LiFePO₄-MWCNTs composite exhibits higher discharge capacity and rate capability than pure LiFePO₄ at high-rate at room temperature. It is demonstrated that the added MWCNTs not only increase the electronic conductivity and lithium-ion diffusion coefficient but also decrease crystallite size and charge transfer resistance of LiFePO₄-MWCNTs composite.     

Thermal explosion synthesis of LiFePO4 as a cathode material for lithium ion batteries

Research on Chemical Intermediates - Olivine-type LiFePO4 cathode material was successfully synthesized by a simple method of thermal explosion (TE) using hexamethylenetetramine (C6H12N4) as fuel....     

The study of carbon nanotubes as conductive additives of cathode in lithium ion batteries

Carbon nanotubes (CNTs), including multi-walled CNTs (MWCNTs) and single-walled CNTs (SWCNTs), are employed as conductive additives in lithium ion batteries. The effects of MWCNTs’ carbon precursors, diameter, and weight fraction on the electrochemical behavior of MWCNTs/LiCoO₂ composite cathode are investigated. Meanwhile, a comparison is made between SWCNTs /LiCoO₂ and MWCNTs/LiCoO₂. Among the three kinds of carbon precursors: CH₄, natural gas, and C₂H₂, MWCNTs prepared from CH₄ are very fit for acting as conductive additives due to their better crystallinity and lower electrical resistance. MWCNTs with smaller diameter favor improving the electrochemical behavior of MWCNTs/LiCoO₂ composite cathode at higher charge/discharge rate owing to their advantage in primary particle number in unit mass. To make full use of LiCoO₂ at higher rate, it is necessary to add at least 5 wt.% of MWCNTs with a diameter 10~30 nm. However, SWCNTs are not expected to be added into LiCoO₂ composite cathode since they tend to form bundles.     

Electrochemical performances of lithium ion batteries from hydrothermally synthesized LiFePO4 and carbon spherules

Hydrothermally synthesized LiFePO₄ cathode and carbon spherules anode materials were investigated by full-cells for the first time. The assembled half-cells suggest that electrode materials prepared hydrothermally have excellent electrochemical properties. Despite having a capacity loss during the formation process, the assembled LiFePO₄/CS full-cells still exhibit an excellent cycling performance with stable coulombic efficiency at 100% and less than 9% capacity fading after 260 cycles, which suggest that hydrothermally fabricated electrode materials have a potential application in EVs and stationary energy storage.     

Macroporous Co3O4 platelets with excellent rate capability as anodes for lithium ion batteries

This paper reports the microwave-assisted synthesis of Co₃O₄ nanomaterials with different morphologies including nanoparticles, rod-like nanoclusters and macroporous platelets. The new macroporous platelet-like Co₃O₄ morphology was found to be the best suitable for reversible lithium storage properties. It displayed superior cycling performances than nanoparticles and rod-like nanoclusters. More interestingly, excellent high rate capabilities (811 mAh g^?1 at 1780 mA g^?1 and 746 mAh g^?1 at 4450 mA g^?1) were observed for macroporous Co₃O₄ platelet. The good electrochemical performance could be attributed to the unique macroporous platelet structure of Co₃O₄ materials.     

High reversible capacity and rate capability of ZnCo2O4/graphene nanocomposite anode for high performance lithium ion batteries

A facile and straightforward method was adopted to synthesize ZnCo₂O₄/graphene nanocomposite anode. In the first step, pure ZnCo₂O₄ nanoparticles were synthesized using urea-assisted auto-combustion synthesis followed by annealing at a low temperature of 400 °C. In the second step, in order to synthesize ZnCo₂O₄/graphene nanocomposite, the obtained pure ZnCo₂O₄ nanoparticles were milled with 10 wt% reduced graphene nanosheets using high energy spex mill for 30 s. The ZnCo₂O₄ nanoparticles, with particle sizes of 25–50 nm, were uniformly dispersed and anchored on the reduced graphene nanosheets. Compared with pure ZnCo₂O₄ nanoparticles anode, significant improvements in the electrochemical performance of the nanocomposite anode were obtained. The resulting nanocomposite delivered a reversible capacity of 1124.8 mAh g⁻¹ at 0.1 C after 90 cycles with 98% Coulombic efficiency and high rate capability of 515.9 mAh g⁻¹ at 4.5 C, thus exhibiting one of the best lithium storage properties among the reported ZnCo₂O₄ anodes. The significant enhancement of the electrochemical performance of the nanocomposite anode could be credited to the strong synergy between ZnCo₂O₄ and graphene nanosheets, which maintain excellent electronic contact and accommodate the large volume changes during the lithiation/delithiation process.     

High capacity silicon/carbon composite anode materials for lithium ion batteries

Silicon/carbon composite materials are prepared by pyrolysis of pitch embedded with graphite and silicon powders. As anode for lithium ion batteries, its initial reversible capacity is 800–900 mAh/g at 0.25 mA/cm² in a voltage range of 0.02/1.5 V vs. Li. The material modification by adding a small amount of CaCO₃ into precursor improves the initial reversibility (η₁=84%) and suppresses the capacity fade upon cycling. A little higher insertion voltage of the composites than commercial CMS anode material improves the cell safety in the high rate charging process.     

锂离子电池正极材料LiFePO4的密度泛函研究

采用密度泛函(B3LYP)方法计算锂离子电池正极材料LiFePO4/FePO4,净电荷和共价键级的计算结果都表明磷氧原子间作用力最强,锂氧原子间作用力最弱,有利于Li离子在晶格中的自由移动.以Li/LiFePO4锂离子电池的平均电压为3.2 V,和实验值3.4 V基本一致.态密度分析表明FePO4和LiFePO4都是典型的半导体,O原子轨道主要贡献总态密度靠费米能级价带一侧,Fe原子轨道主要贡献总态密度靠费米能级导带一侧.     

A selenium-doped carbon anode of high performance for lithium ion batteries

Journal of Solid State Electrochemistry - The strong demand on high-performance lithium ion batteries has brought up an attention upsurge in the research society and the commercial market. Carbon...     

Nano-LiCoO2 as cathode material of large capacity and high rate capability for aqueous rechargeable lithium batteries

Crystalline nanoparticles of LiCoO₂ are prepared by a sol–gel method at 550 °C and characterized by X-ray diffraction. Their electrochemical behaviors were characterized by cyclic voltammograms, capacity measurement and cycling performance. Results show that the reversible capacity of the nano-LiCoO₂ can be up to 143 mAh/g at 1000 mA/g and still be 133 mAh/g at 10,000 mA/g (about 70C) in 0.5 mol/l Li₂SO₄ aqueous electrolyte. In addition, their cycling behavior is also very satisfactory, no evident capacity fading during the initial 40 cycles. These data present great promise for the application of aqueous rechargeable lithium batteries.     

Hierarchical nanostructured composite cathode with carbon nanotubes as conductive scaffold for lithium-sulfur batteries

Carbon nanotubes (CNTs) are excellent scaffolds for advanced electrode materials, resulting from their intrinsic sp2 carbon hybridization, interconnected electron pathway, large aspect ratio, hierarchical porous structures, and low cost at a large-scale production. How to make full utilization of the mass produced CNTs as building blocks for nanocomposite electrodes is not well understood yet. Herein, a composite cathode containing commercial agglomerated multi-walled CNTs and S for Li-S battery was fabricated by a facile melt-diffusion strategy. The hierarchical CNT@S coaxial nanocables exhibited a discharging capacity of 1020 and 740 mAh g-1 at 0.5 and 2.0 C, respectively. A rapid capacity decay of 0.7% per cycle at the initial 10 cycles and a slow decay rate of 0.14% per cycle for the later 140 cycles were detected. Such hierarchical agglomerated CNT@S cathodes show advantages in easy fabrication, environmentally benign, low cost, excellent scalability, and good Li ion storage performance, which are extraordinary composites for high performance Li-S battery.     

Porous structure SnSb/amorphous carbon core-shell composite as high capacity anode materials for lithium ion batteries

SnSb/C core-shell powder has been successfully prepared by modified carbothermal reduction method. The shape, size, morphology, and electrochemical properties of the SnSb/C core-shell powder have been investigated. SnSb particles are completely encapsulated by amorphous carbon shell, and the surface of SnSb/C composite has been characterized with porous structure. The composite has a relatively high BET surface area of 253 m²g^?1. The composite exhibits relatively good capacity retention for 50 cycles at a constant current density of 100 mA g^?1 and show excellent rate performance when the current ranges from 50 to 200 mA g^?1. The improvement of reversible capacity and cyclic performance is attributed to loose and amorphous surface structure which could buffer volume variations through cycle process.     

A novel synthetic route for LiFePO_4/C cathode materials by addition of starch for lithium-ion batteries

LiFePO4/Carbon composite cathode material was prepared using starch as carbon source by spray-pelleting and subsequent pyrolysis in N2. The samples were characterized by XRD, SEM, Raman, and their electrochemical performance was investigated in terms of cycling behavior. There has a special micro-morphology via the process, which is favorable to electrochemical properties. The discharge capacity of the LiFePO4.C composite was 170 mAh g-1, equal to the theoretical specific capacity at 0.1 C rate. At 4 C current density, the specific capacity was about 80 mAh g-1, which can satisfy for transportation applications if having a more flat discharge flat.     

Platelike CoO/carbon nanofiber composite electrode with improved electrochemical performance for lithium ion batteries

Platelike CoO/carbon nanofiber (CNF) composite materials with porous structures are synthesized from the thermal decomposition and recrystallization of β-Co(OH)₂/CNF precursor without the need for a template or structure-directing agent. As negative electrode materials for lithium-ion batteries, the platelike CoO/CNF composite delivers a high reversible capacity of 700 mAh g⁻¹ for a life extending over hundreds of cycles at a constant current density of 200 mA g⁻¹. More importantly, the composite electrode shows significantly improved rate capability and electrochemical reversibility. Even at a current of 2 C, the platelike CoO/CNF composite maintain a capacity of 580 mAh g⁻¹ after 50 discharge/charge cycles. The improved cycling stability and rate capability of the CoO/CNF composite electrodes may be attributed to synergistic effect of the porous structural stability and improved conductivity through CNF connection.     

Li-ion batteries from LiFePO4 cathode and anatase/graphene composite anode for stationary energy storage

Li-ion batteries made from LiFePO₄ cathode and anatase TiO₂/graphene composite anode were investigated for potential application in stationary energy storage. Fine-structured LiFePO₄ was synthesized by a novel molten surfactant approach whereas anatase TiO₂/graphene nanocomposite was prepared via self-assembly method. The full cell that operated at 1.6 V demonstrated negligible fade even after more than 700 cycles at measured 1 C rate. While with relative lower energy density than traditional Li-ion chemistries interested for vehicle applications, the Li-ion batteries based on LiFePO₄/TiO₂ combination potentially offers long life and low cost, along with safety, all which are critical to the stationary applications.     

Designing composite solid-state electrolytes for high performance lithium ion or lithium metal batteries

Solid-state electrolytes (SSEs) are capable of inhibiting the growth of lithium dendrites, demonstrating great potential in next-generation lithium-ion batteries (LIBs). However, poor room temperature ionic conductivity and the unstable interface between SSEs and the electrode block their large-scale applications in LIBs. Composite solid-state electrolytes (CSSEs) formed by mixing different ionic conductors lead to better performance than single SSEs, especially in terms of ionic conductivity and interfacial stability. Herein, we have systematically reviewed recent developments and investigations of CSSEs including inorganic composite and organic–inorganic composite materials, in order to provide a better understanding of designing CSSEs. The comparison of different types of CSSEs relative to their parental materials is deeply discussed in the context of ionic conductivity and interfacial design. Then, the proposed ion transfer pathways and models of lithium dendrite growth in composites are outlined to inspire future development of CSSEs.

Composite solid-state electrolytes (CSSEs) formed by mixing different ionic conductors lead to better performance than a single solid-state electrolytes (SSEs), demonstrating great potentials in the next-generation lithium-ion batteries (LIBs).     

Synthesis and electrochemical properties of K-doped LiFePO4/C composite as cathode material for lithium-ion batteries

Li_1 − x K _x FePO₄/C (x = 0, 0.03, 0.05, and 0.07) composites were synthesized at 700 °C in an argon atmosphere by carbon thermal reduction method. Based on X-ray diffraction, scanning electron microscopy, and transmission electron microscopy analysis, the composite was ultrafine sphere-like particles with 100–300 nm size, and the lattice structure of LiFePO₄ was not destroyed by K doping, while the lattice volume was enlarged. The electrochemical properties were investigated by four-point probe conductivity measurements, galvanostatic charge and discharge tests, cyclic voltammetry and electrochemical impedance spectroscopy. The results indicated that the capacity performance at high rate and cyclic stability were improved by doping an appropriate amount of K, which might be ascribed to the fact that the doped K ion expands Li ion diffusion pathway. Among the doped materials, the Li_0.97K_0.03FePO₄/C samples exhibited the best electrochemical activity, with the initial discharge capacity of 153.7 mAh g⁻¹ at 0.1 C and the capacity retention rate of about 92% after 50 cycles at above 1 C, 11% higher than undoped sample. Remarkably, it still showed good cycle retention at a high current rate of 10 C.     

One-dimensional (1D) nanostructured and nanocomposited LiFePO4: its perspective advantages for cathode materials of lithium ion batteries

Nanostructured materials have attracted recent research interest as battery materials due to their expected enhancement of properties. The characteristic nanoscale dimension and its structuring guarantees improved charge and mass transfer during charge/discharge processes. Among the potential cathode materials investigated as a substitute to LiCoO(2), one of the most promising materials is LiFePO(4) with olivine structure (LFP). In this perspective article, the current research and development in the synthesis and electrochemical studies of nanostructured LFP are reviewed with a special emphasis on one-dimensional (1D) nanostructures and nanocompositing with 1D conductive materials. In addition to various examples of 1D LFP with detailed synthetic methods, why 1D nanostructures could be meaningful is discussed in terms of a geometric point of view and the anisotropic lithiation/de-lithiation mechanism of LFP.     

Synthesis, characterization, and electrochemical performance of LiFePO4/C cathode materials for lithium ion batteries using various carbon sources: best results by using polystyrene nano-spheres

Olivine LiFePO₄/C cathode materials for lithium ion batteries were synthesized using monodisperse polystyrene (PS) nano-spheres and other carbon sources. The structure, morphology, and electrochemical performance of LiFePO₄/C were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), galvanostatic charge–discharge tests, electrochemical impedance spectroscopy (EIS) measurements, and Raman spectroscopy measurements. The results demonstrated that LiFePO₄/C materials have an ordered olivine-type structure with small particle sizes. Electrochemical analyses showed that the LiFePO₄/C cathode material synthesized from 7 wt.% PS nano-spheres delivers an initial discharge capacity of 167 mAh g^-1 (very close to the theoretical capacity of 170 mAh g^-1) at 0.1 C rate cycled between 2.5 and 4.1 V with excellent capacity retention after 50 cycles. According to Raman spectroscopy and EIS analysis, this composite had a lower I _D/I _G, sp ³/sp ² peak ratio, charge transfer resistance, and a higher exchange current density, indicating an improved electrochemical performance, due to the increased proportion of graphite-like carbon formed during pyrolysis of PS nano-spheres, containing functionalized aromatic groups.     

A graphene-amorphous FePO4 hollow nanosphere hybrid as a cathode material for lithium ion batteries

Amorphous FePO(4) hollow nanospheres were directly grown on graphene for use as a cathode material in lithium ion batteries. This hybrid exhibits high rate capability and good cycle stability because of efficient Li(+) ion diffusion through the thin wall of the hollow nanospheres and fast electron transport through the graphene.