Pulse polymerized polypyrrole electrodes for high energy density electrochemical supercapacitor

A novel method of pulsed polymerization for pyrrole exhibiting highest capacitance and very high energy density polypyrrole supercapacitor is reported. Stable polypyrrole films with good electrochemical reversibility and high doping degree were obtained by applying ultra short on time current pulse for polymerization. Pulse on time plays an important role in controlling chain size and chain defects whereas pulse off time contributes in polymer conjugation and orientation. A regime of pulse on time is identified to yield highly capacitive and stable films for supercapacitor application. Very high specific capacitance of 400 F/g and an unexpectedly high energy density of 250 Wh/kg were obtained form pulsed polymerized ordered polypyrrole structures in acidic electrolyte. Stability tests performed on pulsed polymerized pPy electrode yield long cycling life up to 10,000 cycles at charge/discharge current density of 5 mA/cm².     

Graphene oxide doped polyaniline for supercapacitors

A novel high-performance electrode material based on fibrillar polyaniline (PANI) doped with graphene oxide sheets was synthesized via in situ polymerization of monomer in the presence of graphene oxide, with a high conductivity of 10 S cm^?1 at 22 °C for the obtained nanocomposite with a mass ratio of aniline/graphite oxide, 100:1. Its high specific capacitance of 531 F/g was obtained in the potential range from 0 to 0.45 V at 200 mA/g by charge–discharge analysis compared to 216 F/g of individual PANI. The doping and the ratio of graphene oxide have a pronounced effect on the electrochemical capacitance performance of the nanocomposites.     

Anomalous capacity and cycling stability of xLi2MnO3 · (1 − x)LiMO2 electrodes (M = Mn,Ni, Co) in lithium batteries at 50 °C

Transition metal oxides with composite xLi₂MnO₃ ·  (1 − x)LiMO₂ rocksalt structures (M = Mn, Ni, Co) are of interest as a new generation of cathode materials for high energy density lithium-ion batteries. After electrochemical activation to 4.6 or 4.8 V (vs. Li⁰) at 50 °C, xLi₂MnO₃ · (1 − x)LiMn_0.33Ni_0.33Co_0.33O₂ (x = 0.5, 0.7) electrodes deliver initial discharge capacities (>300 mAh/g) at a low current rate (0.05 mA/cm²) that exceed the theoretical values for lithiation back to the rocksalt stoichiometry (240–260 mAh/g), at least during the early charge/discharge cycles of the cells. Attention is drawn to previous reports of similar, but unaccounted and unexplained anomalous behavior of these types of electrode materials. Possible reasons for this anomalous capacity are suggested. Indications are that electrodes in which M = Mn, Ni and Co do not cycle with the same stability at 50 °C as those without cobalt.     

Electrodeposited PbO2 thin film on Ti electrode for application in hybrid supercapacitor

PbO₂ thin films were prepared by pulse current technique on Ti substrate from Pb(NO₃)₂ plating solution. The hybrid supercapacitor was designed with PbO₂ thin film as positive electrode and activated carbon (AC) as negative electrode in the 5.3 M H₂SO₄ solution. Its electrochemical properties were determined by cyclic voltammetry (CV), charge–discharge test and electrochemical impedance spectroscopy (EIS). The results revealed that the PbO₂/AC hybrid supercapacitor exhibited large specific capacitance, high-power and stable cycle performance. In the potential range of 0.8–1.8 V, the hybrid supercapacitor can deliver a specific capacitance of 71.5 F g^?1 at a discharge current density of 200 mA g^?1(4 mA cm^?2) when the mass ratio of AC to PbO₂ was three, and after 4500 deep cycles, the specific capacitance remains at 64.4 F g^?1, or 32.2 Wh Kg^?1 in specific energy, and the capacity only fades 10% from its initial value.     

Double-layer capacitance of waste coffee ground activated carbons in an organic electrolyte

Using ZnCl₂ activation we prepared a series of carbon electrodes from waste coffee grounds to study the effect of mesopores on double-layer capacitance in a tetraethyl ammonium tetrafluoroborate/acetonitrile electrolyte. The activated carbon with the largest mesopore volume achieved an energy density of 34 Wh kg^?1 at low current loads, and significantly retained an energy density of 16.5 Wh kg^?1 and specific capacitance of more than 100 F g^?1 at fast charge–discharge rates (20 A g^?1). The effect of mesopores on capacitance at fast charge–discharge rates is discussed.     

An acidic cellulose–chitin hybrid gel as novel electrolyte for an electric double layer capacitor

A novel acidic cellulose–chitin hybrid gel electrolyte including binary ionic liquids (ILs) with an aqueous H₂SO₄ solution was prepared for an electric double layer capacitor (EDLC). Its electrochemical characteristics were investigated by galvanostatic charge–discharge measurements. The test cell with a hybrid gel electrolyte shows a specific capacitance of 162 F g^?1 at room temperature, which is higher than that for a cell with an H₂SO₄ electrolyte, 155 F g^?1. This hybrid gel electrolyte exhibits excellent high-rate discharge capability in a wide range of current densities as well as an aqueous H₂SO₄ solution. The discharge capacitance of the test cell can retain over 80% of its initial value in 100,000 cycles even at a high current density of 5000 mA g^?1.     

Synthesis of nickel selenide thin films for high performance all-solid-state asymmetric supercapacitors

As a significant semiconductor, nickel selenide shows enormous potential and extensive application prospects in the field of sensor, photocatalysis and supercapacitor. In this paper, nickel selenide (Ni₃Se₂, NiSe) thin films were successfully fabricated on stainless-steel sheet using a facile, effective electrodeposition technique. The morphologies, microstructures and chemical compositions of the thin films are characterized systematically. Electrochemical tests exhibit that the Ni₃Se₂ and NiSe possess high specific capacitance of 581.1 F/g and 1644.7 F/g, respectively. A flexible, all-solid-state asymmetric supercapacitor is assembled by utilizing NiSe film as positive electrode and activated carbon as negative electrode. The solid device delivers a high areal capacitance of 27.0 mF/cm² at the current density of 0.7 mA/cm². The maximum volumetric energy density and power density of the NiSe//AC asymmetric SCs can achieve 0.26 mWh/cm³ and 33.35 mW/cm³, respectively. The device shows robust cycling stability with 84.6% capacitance retention after 10,000 cycles, outstanding flexibility and satisfactory mechanical stability. Moreover, two devices in series can light up a red light-emitting diode, which displayed great potential applications for energy storage.     

Preparation of activated carbon from Turbinaria turbinata seaweeds and its use as supercapacitor electrode materials

Turbinaria turbinata brown seaweeds were tested as carbon electrode material in symmetric, electrochemical supercapacitors. The electrochemical properties of the carbon materials were characterised for their application as supercapacitors using cyclic voltammetry, galvanostatic charge/discharge method and electrochemical impedance spectroscopic analyses. Our initial results showed that the optimal behaviour was obtained for the sample prepared by pyrolysis at 800 °C. The average surface area of the carbon was 812 m²/g. Electrochemical tests with an organic electrolyte gave the following interesting results: a capacitance of 74.5 F/g, a specific series resistance of 0.5 Ω cm² and an ionic resistivity of 1.3 Ω cm². These results show the promising capacitive properties of carbon derived from seaweeds and their application in electrochemical supercapacitors.     

Fibriform polyaniline/nano-TiO2 composite as an electrode material for aqueous redox supercapacitors

Fibriform polyaniline/nano-TiO₂ composite is prepared by one-step in situ oxidation polymerization of aniline in the presence of nano-TiO₂ particles, which contains 80% conducting polyaniline by mass, with a conductivity of 2.45 S/cm at 25 °C. Its maximum specific capacitance is 330 F g^?1 at a constant current density of 1.5 A g^?1, and can be subjected to charge/discharge over 10,000 cycles in the voltage range of 0.05–0.55 V.     

Microstructures and electrochemical hydrogen storage properties of novel Mg–Al–Ni amorphous composites

The amorphous Mg–Al–Ni composites were prepared by mechanical ball-milling of Mg₁₇Al₁₂ with x wt.% Ni (x = 0, 50, 100, 150, 200). The effects of Ni addition and ball-milling parameters on the electrochemical hydrogen storage properties and microstructures of the prepared composites have been investigated systematically. For the Mg₁₇Al₁₂ ball-milled without Ni powder, its particle size decreases but the crystal structure does not change even the ball-milling time extending to 120 h, and its discharge capacity is less than 15 mAh g^?1. The Ni addition is advantageous for the formation of Mg–Al–Ni amorphous structure and for the improvement of the electrochemical characteristics of the composites. With the Ni content x increasing, the composites exhibit higher degree of amorphorization. Moreover, the discharge capacity of the composite increases from 41.3 mAh g^?1 (x = 50) to 658.2 mAh g^?1 (x = 200) gradually, and the exchange current density I₀ increases from 67.1 mA g^?1 (x = 50) to 263.8 mA g^?1 (x = 200), which is consistent with the variation of high-rate dischargeability (HRD). The ball-milled Mg₁₇Al₁₂ + 200 wt.% Ni composite has the highest cycling discharge capacity in the first 50 cycles.     

Vertical crosslinking MoS2/three-dimensional graphene composite towards high performance supercapacitor

The vertical crosslinking MoS₂/three-dimensional graphene composite has been prepared by hydrothermal method, which delivered a superior and stable electrochemical capacitive performance.     

Achieving high electrode specific capacitance with materials of low mass specific capacitance: Potentiostatically grown thick micro-nanoporous PEDOT films

Electrode materials for supercapacitors are at present commonly evaluated and selected by their mass specific capacitance (C_M, F g⁻¹). However, using only this parameter may be a misleading practice because the electrode capacitance also depends on kinetics, and may not increase simply by increasing material mass. It is therefore important to complement C_M by the practically accessible electrode specific capacitance (C_E, F cm⁻²) in material selection. Poly[3,4-ethylene-dioxythiophene] (PEDOT) has a mass specific capacitance lower than other common conducting polymers, e.g. polyaniline. However, as demonstrated in this communication, this polymer can be potentiostatically grown to very thick films (up to 0.5 mm) that were porous at both micro- and nanometer scales. Measured by both cyclic voltammetry and electrochemical impedance spectrometry, these thick PEDOT films exhibited electrode specific capacitance (C_E, F cm⁻²) increasing linearly with the film deposition charge, approaching 5 F cm⁻², which is currently the highest amongst all reported materials.     

Electrochemical reactions of reversible intercalation in Chevrel compounds for cationic transfer – Principle and application on Co2+ ion

The process is an application of the reversible electrochemical reactions of insertion and deinsertion in the mineral host matrix M_xMo₆S₈ Chevrel phases to carry out the transfer of cations between two electrolytes. The device and the associated process are built around an electrochemical transfer junction (ETJ) placed between two tanks. The whole allows a transfer of cobalt cations (∼5 × 10⁻⁶ mol/h/cm² for a junction thickness of 4 mm) by application of a current density controlled between electrodes placed in both tanks.     

Impedance study on the correlation between phase transition and electrochemical degradation of Si-based materials

In order to explain the relationship between physical change and electrochemical degradation of Co–Co₃O₄ coated Si, impedance spectroscopy on Co–Co₃O₄ coated Si was conducted at various states during charge or discharge. Nyquist plots during Li⁺ insertion (charge) showed a unique behavior that below 70 mV vs. Li/Li⁺, the more Li⁺’s were inserted into the electrode, the larger its comprehensive resistance was getting. During Li⁺ extraction (discharge), electrode resistance was decreased after going through 0.43 V vs Li/Li⁺. When these data were fitted with the ordinary equivalent circuit which is composed of electrolyte resistance, charge transfer resistance and contact resistance, there was an abrupt augmentation of charge transfer resistance below 70 mV vs. Li/Li⁺ during charge, whereas there was its drastic diminishment between 0.2 and 0.5 V vs. Li/Li⁺ during discharge. Because these potential regions are each related to amorphous Li_xSi-to-Li₁₅Si₄ transition and vice versa, it could be shown that the formation and decomposition of Li₁₅Si₄ is responsible for the electrochemical degradation of Co–Co₃O₄ coated Si.     

Plastic–polymer composite electrolytes: Novel soft matter electrolytes for rechargeable lithium batteries

We present here a soft matter solid composite electrolyte obtained by inclusion of a polymer in a semi-solid organic plastic lithium salt electrolyte. Compared to lithium bis-trifluoromethanesulfonimide-succinonitrile (LiTFSI-SN), the (100 − x)%-[LiTFSI-SN]: x%-P (P: polyacrylonitrile (PAN), polyethylene oxide (PEO), polyethylene glycol dimethyl ether (PEG)) composites possess higher ambient temperature ionic conductivity, higher mechanical strength and wider electrochemical window. At 25 °C, ionic conductivity of 95%-[0.4 M LiTFSI-SN]: 5%-PAN was 1.3 × 10⁻³ Ω⁻¹ cm⁻¹ which was twice that of LiTFSI-SN. The Young’s modulus (Y) increased from Y → 0 for LiTFSI-SN to a maximum ∼1.0 MPa for (100 − x)%-[0.4 M LiTFSI-SN]: x%-PAN samples. The electrochemical voltage window for composites was approximately 5 V (Li/Li⁺). Excellent galvanostatic charge/discharge cycling performance was obtained with composite electrolytes in Li|LiFePO₄ cells without any separator.     

Nitrogen enriched mesoporous carbon spheres obtained by a facile method and its application for electrochemical capacitor

A kind of mesoporous carbon spheres (MCS) containing in-frame incorporated nitrogen has been prepared by a facile polymerization-induced colloid aggregation method. As the electrode material for electric double layer capacitor (EDLC) in 5 mol/L H₂SO₄, the MCS products present excellent specific capacitance as 211 F/g much larger than that of the most popularly applied activated carbon at a high discharge current density of 1 A/g. Its specific capacitance can still remain 200 F/g at 20 A/g. The superior electrochemical performance of MCS is associated with the following characteristics: high specific surface area (∼1330 m²/g) contributed mainly by the mesopores, uniform pore size as large as 29 nm and moderate content of nitrogen (10 wt%), which are the requirements for ideal supercapacitors.     

Electrodeposition of MnO2 nanowires on carbon nanotube paper as free-standing,flexible electrode for supercapacitors

MnO₂ nanowires were electrodeposited onto carbon nanotube (CNT) paper by a cyclic voltammetric technique. The as-prepared MnO₂ nanowire/CNT composite paper (MNCCP) can be used as a flexible electrode for electrochemical supercapacitors. Electrochemical measurements showed that the MNCCP electrode displayed specific capacitances as high as 167.5 F g⁻¹ at a current density of 77 mA g⁻¹. After 3000 cycles, the composite paper can retain more than 88% of initial capacitance, showing good cyclability. The CNT paper in the composite acted as a good conductive and active substrate for flexible electrodes in supercapacitors, and the nanowire structure of the MnO₂ could facilitate the contact of the electrolyte with the active materials, and thus increase the capacitance.     

The superior electrochemical performance of oxygen-rich activated carbons prepared from bituminous coal

Oxygen-rich activated carbons (OAC) were prepared from bituminous coal through a quick KOH activation. OAC exhibited a moderately large surface area of 1950 m²/g, a relative wide pore size distribution, good conductivity and very high oxygen content (up to 12 wt.%). Compared with high surface area activated carbons prepared by the conventional KOH activation, OAC have superior capacitive behavior, power output and high energy density in electrochemical double layer capacitors (EDLC). OAC presented a high specific capacitance of 370 F/g in 3 M KOH electrolyte at a low current density of 50 mA/g and still remained 270 F/g even at a high current density of 20 A/g.     

Nb2O5 nanobelts: A lithium intercalation host with large capacity and high rate capability

In this study, Nb₂O₅ nanobelts, with a ca. ∼15 nm in thickness, ca. ∼60 nm in width and several tens of mircrometers in length, have first been used as the electrode material for lithium intercalation over the potential window of 3.0–1.2 V (vs. Li⁺/Li). It delivers an initial intercalation capacity of 250 mA hg⁻¹ at 0.1 Ag⁻¹ current density, corresponding to x = 2.5 for L_xNb₂O₅, and can still keep relative stable and reaches as large as 180 mA hg⁻¹ after 50 cycles. Surprisingly, the electrodes composed of Nb₂O₅ nanobelts can work smoothly even at high current density of 10 Ag⁻¹, and shows higher specific capacity and excellent cycling stable, as well as sloped feature in voltage profile. Cycling test indicates Nb₂O₅ nanobelts electrode shows a high reversible charge/discharge capacity, high rate capability with excellent cycling stability.     

The Ti@MoOx nanorod array as a three dimensional film electrode for micro-supercapacitors

Ti@MoO_x core–shell nanorod arrays with diameters within 100 nm were fabricated by electrodepositing MoO_x on a Ti nanorod array prepared by oblique angle deposition. A high areal capacitance of 27 mF cm^− 2 and satisfactory cycling stability were obtained. After post-annealing, MoO₂ grains were introduced to enhance the rate capability, suggesting a potential pseudocapacitive micro-electrode.