Electrospun octa(3-chloropropyl)-polyhedral oligomeric silsesquioxane-modified polyvinylidene fluoride/poly(acrylonitrile)/poly(methylmethacrylate) gel polymer electrolyte for high-performance lithium ion battery

Gel polymer electrolyte (GPE) based on octa(3-chloropropyl)-polyhedral oligomeric silsesquioxane (OCP-POSS)-modified polyvinylidene fluoride/poly(acrylonitrile) /poly(methylmethacrylate) (PVDF/PAN/PMMA) fibrous membrane was prepared by electrospinning method to improve the thermal stability of GPE and prevent the leakage of liquid electrolyte for lithium ion battery. The effect of OCP-POSS content on the morphology, porosity and electrolyte uptake, mechanical strength, thermal stability of spinning fibrous membrane and ionic conductivity, electrochemical stability window, and interface resistance of GPE was investigated. The cycle performance of cells assembled with GPE was also tested. The results show that the spinning fibrous membrane with 10 wt% OCP-POSS possesses high electrolyte uptake (660%) and excellent thermal stability. The ionic conductivity of corresponding GPE is 9.23 × 10^?3 S cm^?1 at room temperature and the electrochemical stability window is up to 5.82 V; the interface resistance of 10 wt% OCP-POSS modified GPE decreases by 42% after 168 h compared with pure PVDF/PAN/PMMA GPE. Furthermore, cells assembled with 10 wt% OCP-POSS modified GPE show high discharge capacity (166.5 mA h g^?1 at 0.1 C) and excellent cycle stability during 50 cycles. The results indicate that the GPE could improve the safety of lithium ion battery and show great potential in lithium ion battery applications.     

High ionic conductive PVDF-based fibrous electrolytes

The high ionic conductive polymer electrolytes were prepared based on poly(vinylidenefluoride) (PVDF) fibers modified via preirradiation grafting poly(methyl methacrylate) (PMMA). In these polymer electrolytes, the PVDF fibers served as the supporting phase providing dimensional stability, and PMMA acted as the gel phase helping for the trapping liquid electrolyte and substituting the nonconductive PVDF phase to provide contact with electrodes well thus increasing conductive area. The modified PVDF fibrous membranes were used as a polymer electrolyte in lithium ion battery after they were activated by uptaking 1 M LiPF₆/ethylene carbonate–dimethyl carbonate (1:1 vol) liquid electrolyte, which showed a much higher room-temperature ionic conductivity than the pristine PVDF fibrous membrane. The LiCoO₂-mesocarbon microbead coin cells containing the dual-phase fibrous membrane (degree of graft, 111.8%) demonstrated excellent rate performance, and the cell still retained about 86% of discharge capacity at 4C rate, as compared to that at 0.1C rate. The prototype cell showed good cycle performance.     

A novel process to prepare porous membranes comprising SnO2 nanoparticles and P(MMA-AN) as polymer electrolyte

We have successfully developed a new process to prepare porous poly(methyl methacrylate-co-acrylonitrile) (P(MMA-AN)) copolymer based gel electrolyte. The porous structure in the polymer matrix is achieved by adding SnO₂ nanoparticles which are mostly used as gas sensor materials. The quasi-aromatic solvent, NMP, has an electron-repulsion effect with the space charge layer on the surface of SnO₂ nanoparticles and forms a special gas–liquid phase interface. Once the cast polymer solution is stored at an elevated temperature to evaporate the solvent, gas–liquid phase separation happens and spherical pores are obtained. The ionic conductivity at room temperature of the prepared gel polymer electrolyte based on the porous membrane is as high as 1.54 × 10⁻³ S cm⁻¹ with the electrochemical stability up to 5.10 V (vs. Li/Li⁺). This method presents another promising way to prepare porous polymer electrolyte for practical use.     

Morphology and properties of hollow-fiber membrane made by PAN mixing with small amount of PVDF

In this paper, the morphological structure and properties such as, miscibility, tensile strength, flux and retention ratio of hollow-fiber membranes manufactured by PAN mixing with small amounts of PVDF have been studied. The hollow fiber was made from a spinning solution composed of polymer (PAN : PVDF=10 : 0, 9 : 1, 7 : 3), additive (PVP, PEG-600) and solvent (DMAC) when immersed in water. The spinnability of blend polymer and the influences of blending on spinning technology have been observed; the morphology of membranes were examined by SEM. The blend membranes possess much higher flux than PAN membrane and fairly good retention ratio especially for the membrane made by PAN : PVDF=9 : 1.     

In situ fabrication of lithium polymer battery basing on a novel electro-polymerization technique

Electro-polymerization technology is proposed for the in situ fabrication of polymer lithium secondary battery and exciting results have been obtained. The polymerization starts from a common used electrolyte of 1 M LiTFSI in DOL/DME (2:1 by weight) with no initiator addition through a routine charge–discharge treatment under some appointed current rate. It is found that once an appropriate current is applied in the charging–discharging of Li/1 M LiTFSI in DOL + DME/LiCoO₂ cell, the original liquid electrolyte polymerizes readily during the first several cycles in an irreversible mode, and thus the desired polymer electrolyte obtained. SEM observation indicates that unlike previous report, the designed electro-polymerization does not result in destructive local break and then turnoff of the circuit, just the reverse, it helps to the formation of a smooth polymer layer, which can effectively protect the lithium substrate from corrosion and dendrite growth. Detailed examination shows that the in situ electro-polymerization does not disturb the electrochemical behavior of the cell, the cycleabilty, internal resistance are all comparable to that of a normal Li/LiCoO₂ liquid secondary battery.     

A porous polymer electrolyte based on P(VDF-HFP) prepared by a simple phase separation process

A polymer electrolyte with interconnected pores based on poly(vinylidene difluoride-co-hexafluoropropylene) [P(VDF-HFP)] copolymer was prepared by a simple phase separation process using water as both non-solvent and pore inducer. The prepared porous membrane was characterized by SEM, XRD and DSC. With a narrow pore size distribution and low crystallinity, the resulting polymer electrolyte shows a high ionic conductivity up to 1.76 × 10⁻³ S cm⁻¹ at room temperature and exhibits low apparent activation energy of 10.35 kJ mol⁻¹ for the transportation of ions. Its low cost and environmentally friendliness provide great promise for the practical application in polymer lithium-ion batteries.     

A new composite polymer electrolyte based on poly(ethyleneoxide)/ polysiloxane/BMImTFSI/organomontmorillonite

Composite polymer electrolytes based on poly(ethylene oxide)-polysiloxane/l-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide/organomontmorillonite(PEO-PDMS/1L/OMMT) were prepared and characterized.Addition of both an ionic liquid and OMMT to the polymer base of PEO-PDMS resulted in an increase in ionic conductivity.At room temperature,the ionic conductivity of sample PPB100-OMMT4 was 2.19×10~3 S/cm.The composite polymer electrolyte also exhibited high thermal and electrochemical stability and may potentially be applied in lithium batteries.     

A lotus root-like porous nanocomposite polymer electrolyte

A lotus root-like porous nanocomposite polymer electrolyte (NCPE) based on poly(vinylidene difluoride-co-hexafluoropropylene) [P(VDF-HFP)] copolymer and TiO₂ nanoparticles was easily prepared by a non-solvent induced phase separation (NIPS) process. The formation mechanism of the lotus root-like porous structure is explained by a qualitative ternary phase diagram. The resulting NCPE had a high ionic conductivity up to 1.21 × 10⁻³ S cm⁻¹ at room temperature, and exhibited a high electrochemical stability potential of 5.52 V (vs. Li/Li⁺), lithium ion transference number of 0.65 and 22.89 kJ mol⁻¹ for the apparent activation energy for transportation of ions. It is of great potential application in polymer lithium ion batteries.     

A novel sandwiched membrane as polymer electrolyte for application in lithium-ion battery

A novel kind of sandwiched polymer membrane was prepared, which consists of two outer layers of electrospun poly(vinyl difluoride) (PVDF) fibrous films and one inner layer of poly(methyl methacrylate) (PMMA) film. Its characteristics were investigated by scanning electron microscopy and X-ray diffraction. The membrane can easily absorb non-aqueous electrolyte to form gelled polymer electrolytes (GPEs). The resulting gelled polymer electrolytes had a high ionic conductivity up to 1.93 × 10⁻³ S cm⁻¹ at room temperature, and exhibited a high electrochemical stability potential of 4.5 V (vs. Li/Li⁺). It is of great potential application in polymer lithium-ion batteries.     

PVDF/PMMA brushes membrane for lithium‐ion rechargeable batteries prepared via preirradiation grafting technique

Poly(methyl methacrylate) (PMMA) was anchored to multiporous poly(vinylidine fluoride) (PVDF) surface via electron beam preirradiation grafting technique to prepare PVDF/PMMA brushes. The conformation of the PVDF/PMMA brushes was verified through Attenuated total reflection‐Fourier transform infra red spectroscopy (ATR‐FTIR), energy dispersive X‐ray spectroscopy (EDX), and scanning electron microscopy (SEM). Thermal stability of PVDF/PMMA brushes was characterized by thermo gravimetric analysis (TGA). The degradation of PVDF/PMMA brushes showed a two‐step pattern. PVDF/PMMA brushes membrane could be used as polymer electrolyte in lithium‐ion rechargeable batteries after it was activated by uptaking 1 M LiPF₆/EC‐DMC (ethylene carbonate/dimethyl carbonate; EC:DMC = 1:1 by volume) electrolyte solution. The activated membrane showed high ionic conductivity, 6.1 × 10^?3 S cm^?1 at room temperature, and a good electrochemical stability up to 5.0 V. The excellent performances of multiporous PVDF‐g‐PMMA membranes suggest that they are suitable for application in high‐performance lithium‐ion batteries. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 751–758, 2008     

Polyacrylamide-lithium chloride polymer electrolyte and its applications in electrochemical capacitors

A neutral polymer electrolyte containing lithium chloride (LiCl) and polyacrylamide (PAM) was developed. The LiCl-PAM electrolyte film had an amorphous structure and an ionic conductivity > 10 mS cm^− 1. The addition of LiCl to the polyacrylamide did not alter the chemical bonding of PAM. Symmetric double layer capacitors (EDLC) were constructed using CNT-graphite electrodes. The solid EDLC retained approximately 85% of the capacitance achieved with a baseline cell in a LiCl aqueous solution. The solid EDLC devices demonstrated a wide voltage window (1.5 V), good cycle life (> 10,000 cycles), and excellent rate capability (up to 5 V s^− 1).     

Poly(ether amine) and cross-linked poly(propylene oxide) diacrylate thin-film polymer electrolyte for 3D-microbatteries

This paper presents a novel thin-film electrolyte of a 2:1 blend of polyetheramine (glyceryl poly(oxypropylene)) and cross-linked oligomeric poly(propylene oxide) diacrylate with LiTFSI. The polyetheramine acts as a surfactant, and can thereby be applied as a conformal coating on complex surfaces—here demonstrated for porous LiFePO₄ cathodes—making it useful for 3D-microbatteries. The poly(propylene oxide) diacrylate blends with the surfactant and is easily UV cross-linked, thereby ensuring good mechanical stability. Electrolytes, ~ 2 μm thick, were casted onto LiFePO₄ cathodes and cycled against metallic lithium, displaying stable discharge capacities of ~ 8 mAh/g at room temperature and ~ 120 mAh/g at 60 °C. The electrolyte showed conductivities of 3.45 × 10^? 6 and 5.80 × 10^? 5 S cm^? 1 at room temperature and 60 °C, respectively.     

Li/LiFePO4 batteries with room temperature ionic liquid as electrolyte

Room temperature ionic liquid (RTIL) was prepared on basis of N-methyl-N-butylpiperidinium bis(trifluoromethanesulfonyl)imide (PP₁₄TFSI), which showed a wide electrochemical window (?0.1–5.2 V vs. Li⁺/Li) and is theoretically feasible as an electrolyte for batteries with metallic Li as anodes. The addition of vinylene carbonate (VC) improved the compatibility of PP₁₄TFSI-based electrolyte towards lithium anodes and enhanced the formation of solid electrolyte interphase film to protect lithium anodes from corrosion. Accordingly, Li/LiFePO₄ cells initially delivered a discharge capacity of about 127 mAh g^?1 at a current density of 17 mA g^?1 in the ionic liquid with the addition of VC and showed better cyclability than in the neat ionic liquid. Electrochemical impedance spectroscopy disclosed that the addition of VC enhanced Li-ion diffusion and depressed interfacial resistance significantly.     

Fingerprint imaging by scanning electrochemical microscopy

An efficient strategy for visualizing human fingerprints on a poly(vinylidene difluoride) membrane (PVDF) by scanning electrochemical microscopy (SECM) has been developed. Compared to a classical ink fingerprint image, here the ink is replaced by an aqueous solution of bovine serum albumin (BSA). After placing the “inked” finger on a PVDF membrane, the latent image is stained by silver nitrate and the fingerprint is imaged electrochemically using potassium hexachloroiridate (III) (K₃IrCl₆) as a redox mediator. SECM images with an area of 5 mm × 3 mm have been recorded with a high-resolution using a 25-μm-diameter Pt disk-shaped microelectrode. Pores in the skin (40–120 μm in diameter) and relative locations of ridges were clearly observed. The factors relevant to the quality of fingerprint images are discussed.     

Sulfur doped reduced graphene oxide as metal-free catalyst for the oxygen reduction reaction in anion and proton exchange fuel cells

Sulfur doped reduced graphene oxide (S-rGO) is investigated for catalytic activity towards the oxygen reduction reaction (ORR) in acidic and alkaline electrolytes. X-ray photoelectron spectroscopy shows that sulfur in S-rGO is predominantly integrated as thiophene motifs within graphene sheets. The overall sulfur content is determined to be approximately 2.2 at.% (elemental analysis). The catalytic activity of S-rGO towards the ORR is investigated by both rotating disc electrode (RDE) and polymer electrolyte fuel cell (PEFC) measurements. RDE measurements reveal onset potentials of 0.3 V and 0.74 V (vs. RHE) in acidic and alkaline electrolyte, respectively. In a solid electrolyte fuel cell with S-rGO as cathode material, this is reflected in an open circuit voltage of 0.37 V and 0.78 V and a maximum power density of 1.19 mW/cm² and 2.38 mW/cm² in acidic and alkaline polymer electrolyte, respectively. This is the first report investigating the catalytic activity of a sulfur doped carbon material in both acidic and alkaline liquid electrolyte, as well as in both proton and anion exchange polymer electrolyte fuel cells.     

Li2SO4-polyacrylamide polymer electrolytes for 2.0 V solid symmetric supercapacitors

A neutral polymer electrolyte comprised of lithium sulfate (Li₂SO₄) and polyacrylamide (PAM) was developed. The Li₂SO₄-PAM electrolyte film shows an ionic conductivity up to 10 mS cm^− 1 in 45%RH conditions. Solid double layer capacitors were demonstrated using CNT-graphite electrodes and Li₂SO₄-PAM solid electrolytes. The voltage window of the solid cell was about 2.0 V, identical to that of a Li₂SO₄ liquid cell used as baseline. The demonstrated voltage window is significantly larger than that reported for proton- or hydroxyl-conducting electrolytes, suggesting that the Li₂SO₄-PAM electrolyte is a promising system for high energy density supercapacitors. The solid device also demonstrated excellent rate capability (up to 5 V s^− 1) and good cycle life (beyond 10,000 charge/discharge cycles).     

Severe accelerated degradation of PEMFC platinum catalyst: A thin film IL-SEM study

The degradation of a commercial platinum polymer electrolyte membrane (PEM) fuel cell catalyst has been studied under severe simulated start–stop conditions (50,000 cycles from 0.2 V to 1.4 V vs. the reversible hydrogen electrode, RHE), employing a newly developed identical location scanning electron microscopy technique (IL-SEM). We show that significant platinum particle growth occurs on top of the catalyst film while platinum depletion takes place in the layers beneath. There is a possibility of misleading interpretation of thin film severe degradation experiments, when the catalyst loading and volume of electrolyte are neglected and when the non-identical location electron microscopy pictures are statistically analyzed.     

Nonenzymatic glucose fuel cells with an anion exchange membrane as an electrolyte

Nonenzymatic glucose fuel cells were prepared by using a polymer electrolyte membrane and Pt-based metal catalysts. A fuel cell with a cation exchange membrane (CEM), which is often used for conventional polymer electrolyte fuel cells, shows an open circuit voltage (OCV) of 0.86 V and a maximum power density (P_max) of 1.5 mW cm^?2 with 0.5 M d-glucose and humidified O₂ at room temperature. The performance significantly increased to show an OCV of 0.97 V and P_max of 20 mW cm^?2 with 0.5 M d-glucose in 0.5 M KOH solution when the electrolyte membrane was changed from a CEM to an anion exchange membrane (AEM). This is due to the superior catalytic activity for both glucose oxidation and oxygen reduction in alkaline medium than in acidic medium. The anodic reaction of the fuel cell can be estimated to be the oxidation of glucose to gluconic acid via a two-electron process under these experimental conditions. The crossover of glucose through an electrolyte membrane was negligibly small compared with methanol and may not represent a serious technical problem due to the cross-reaction.     

Photovoltaic performance of dye-sensitized solar cells assembled by in-situ chemical cross-linking

Quasi-solid state dye-sensitized solar cells (DSSCs) were assembled by in-situ chemical cross-linking of a gel electrolyte precursor containing liquid electrolyte. The DSSCs assembled with this cross-linked gel polymer electrolyte showed higher open circuit voltage and lower short-circuit photocurrent density than those of DSSCs with liquid electrolyte. Addition of SiO₂ nanoparticles into the cross-linked gel polymer electrolyte significantly improved the photovoltaic performance and long-term stability of the DSSCs. The optimized quasi-solid state DSSC showed high conversion efficiency, 6.2% at 100 mW cm^?2 with good durability.     

A novel polymeric electrolyte based on a copolymer containing self-assembled stearylate moiety for lithium-ion batteries

A novel polymeric electrolyte based on a self-assembled copolymer moiety has been prepared by a simple method of photo-induced radical polymerization of a mixture consisting of stearylmethacrylate (SMA) and poly(ethylene glycol)-monomethacrylate (PEM) that dissolves LiBF₄ as the electrolytic salt. The SMA moiety work as mechanically stable backbone and the PEM unit dissolving the salts serves as ion-conducting path in the polymeric composite. Solid-state NMR measurements indicated that the resulting polymer composite consists of PEM-rich and SMA-rich phases, each of which exists within several nanometers apart. The ionic conductivity of the polymer electrolyte with the composition of PEM/SMA = 7/3 (by mass ratio) was 2.8 × 10^?5 S cm^?1 at 50 °C, which was significantly higher than that of the polymer electrolyte based on cross-linked PEM copolymer without SMA.