A new promising high temperature lithium battery solid electrolyte

Lithium lanthanoid silicates find importance as a solid electrolyte in high temperature lithium batteries in view of its high ionic conductivity at high temperatures. An first ever attempt is made to synthesis a new high temperature solid electrolyte viz., lithium samarium holmium silicate by sol–gel process and it has been characterized by thermal analysis (TGA–DTA), X-ray diffraction (XRD), infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). Lithium ion conductivity of 0.8087 × 10⁻⁷ Ω⁻¹ cm⁻¹ at 25 °C was obtained and it increases with increasing temperature. For the first time a highest conductivity of 0.1095 × 10⁻² Ω⁻¹ cm⁻¹ was obtained at 850 °C which is high compared to other high temperature lithium battery solid electrolytes.     

A simple method of electrochemical lithium intercalation within graphite from a propylene carbonate-based solution

Electrochemical lithium intercalation within graphite from 1 mol dm^− 3 solution of LiClO₄ in propylene carbonate (PC) was investigated at 25 and − 15 °C. Lithium ions were intercalated into and de-intercalated from graphite reversibly at − 15 °C despite the use of pure PC as the solvent. However, ceaseless solvent decomposition and intense exfoliation of graphene layers occurred at 25 °C. The results of the Raman spectroscopic analysis indicated that the interaction between PC molecules and lithium ions became weaker at − 15 °C by chemical exchange effects, which suggested that the thermodynamic stability of the solvated lithium ions was an important factor that determined the formation of a solid electrolyte interface (SEI) in PC-based solutions. Charge–discharge analysis revealed that the nature of the SEI formed at − 15 °C in 1 mol dm^− 3 of LiClO₄ in PC was significantly different from that formed at 25 °C in 1 mol dm^− 3 of LiClO₄ in PC containing vinylene carbonate, 3.27 mol kg^− 1 of LiClO₄ in PC, and 1 mol dm^− 3 of LiClO₄ in ethylene carbonate.     

Low-temperature performance of LiFePO4/C cathode in a quaternary carbonate-based electrolyte

The low-temperature performance of LiFePO₄/C cathode in a quaternary carbonate-based electrolyte (1.0 M LiPF₆/EC+DMC+DEC+EMC (1:1:1:3, v/v)) was studied. The discharge capacities of the LiFePO₄/C cathode were about 134.5 mAh/g (20 °C), 114 mAh/g (0 °C), 90 mAh/g (−20 °C) and 69 mAh/g (−40 °C) using a 1C charge–discharge rate. Cyclic voltammetry measurements show obviously sluggish of the lithium insertion–extraction process of the LiFePO₄/C cathode as the operation temperature falls below −20 °C. Electrochemical impedance analyses demonstrate that the sluggish of charge-transfer reaction on the electrolyte/LiFePO₄/C interface and the decrease of lithium diffusion capability in the bulk LiFePO₄ was the main performance limiting factors at low-temperature.     

Novel SrSc0.2Co0.8O3−δ as a cathode material for low temperature solid-oxide fuel cell

The SrSc_0.2Co_0.8O_3−δ (SSC) perovskite was investigated as a cathode material for low temperature solid-oxide fuel cell. The material showed an almost linear thermal expansion from room temperature to 1000 °C in air with the average thermal expansion coefficient of only 16.9 × 10⁻⁶ K⁻¹. The Sc-doping made the absence of Co⁴⁺ in SSC, which resulted in not only dramatically reduced thermal expansion coefficient but also extremely high oxygen vacancies concentrations in the lattice at low temperature. The area specific polarization resistance was 0.206 Ω cm² for SSC at 550 °C, which is about 52% lower than the value of a Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ-based cathode. A peak power density as high as 564 mW cm⁻² was obtained at 500 °C based on a 20 μm thick Sm_0.2Ce_0.8O_1.9 electrolyte by adopting SSC cathode.     

Cost-effective solid oxide fuel cell prepared by single step co-press-firing process with lithiated NiO cathode

A cost-effective cell fabrication process was developed for intermediate temperature solid oxide fuel cells (IT-SOFCs). Co-doped ceria Ce_0.8Gd_0.05Y_0.15O_1.9 (GYDC) was synthesized by carbonate co-precipitation method. Lithiated NiO was prepared by glycine-nitrate combustion method and adopted as cathode material for IT-SOFCs. Single cell was fabricated by one-step dry-pressing and co-firing anode, anode functional layer (AFL), electrolyte and cathode together at 1200 °C for 4 h. The cell presented decent performance and an overall electrode polarization resistance of 0.54 Ω cm² has been achieved at 600 °C. These results demonstrate the possibility of using lithiated NiO as cathode material for ceria-based IT-SOFCs and the development of affordable fuel cell devices is encouraged.     

Non-successive degradation in bulk-type all-solid-state lithium battery with rigid interfacial contact

Bulk-type all-solid-state lithium battery adopting garnet structured electrolyte has been successfully realized by improving the state of interface contact between cathode/electrolyte, as well as cathode particles in the composite layer. The cycle life of the battery has been examined at room temperature, and at elevated temperature of 80 ^°C and 150 ^°C. It exhibits that under high tested current density, the cell exhibits non-successive degradation during cycling, whereas successive degradation under low current density. Impedance spectroscopy measurements, as well as cross-sectional SEM images have been used to complement the electrochemical data in examining structural changes. The results indicate that the destructive damage of cracks originated from the volume change of LiCoO₂ particles in the composite layer is responsible for the non-successive degradation of cell during cycling.     

Poly(ether amine) and cross-linked poly(propylene oxide) diacrylate thin-film polymer electrolyte for 3D-microbatteries

This paper presents a novel thin-film electrolyte of a 2:1 blend of polyetheramine (glyceryl poly(oxypropylene)) and cross-linked oligomeric poly(propylene oxide) diacrylate with LiTFSI. The polyetheramine acts as a surfactant, and can thereby be applied as a conformal coating on complex surfaces—here demonstrated for porous LiFePO₄ cathodes—making it useful for 3D-microbatteries. The poly(propylene oxide) diacrylate blends with the surfactant and is easily UV cross-linked, thereby ensuring good mechanical stability. Electrolytes, ~ 2 μm thick, were casted onto LiFePO₄ cathodes and cycled against metallic lithium, displaying stable discharge capacities of ~ 8 mAh/g at room temperature and ~ 120 mAh/g at 60 °C. The electrolyte showed conductivities of 3.45 × 10^? 6 and 5.80 × 10^? 5 S cm^? 1 at room temperature and 60 °C, respectively.     

A hierarchical micro/nanostructured 0.5Li2MnO3·0.5LiMn0.4Ni0.3Co0.3O2 material synthesized by solvothermal route as high rate cathode of lithium ion battery

A hierarchical micro/nanostructured Li-rich layered 0.5Li₂MnO₃·0.5LiMn_0.4Ni_0.3Co_0.3O₂ (H-LMNCO) material is prepared for the first time through the development of a solvothermal method, and served as cathode of lithium ion batteries. Electrochemical tests indicate that the H-LMNCO exhibits both a high reversible capacity and an excellent rate capability. The reversible discharge capacity of the H-LMNCO has been measured as high as 300.1 mAh·g^− 1 at 0.2 C rate. When the rate is increased to 10 C, the discharge capacity could still maintain a high value of 163.3 mAh·g^− 1. The results demonstrate that the developed solvothermal route is a novel synthesis strategy of preparing high rate performance Li-rich layered cathode material for lithium ion batteries.     

Hydrogen/oxygen polymer electrolyte membrane fuel cells (PEMFCs) based on alkaline-doped polybenzimidazole (PBI)

When complexed with alkaline such as potassium hydroxide, sodium hydroxide or lithium hydroxide, films (40 μm thick) of polybenzimidazole (PBI) show conductivity in the 5 × 10⁻⁵–10⁻¹ S/cm⁻¹ range, depending on the type of alkali, the time of immersion in the corresponding base bath and the temperature of immersion. It has been shown that PBI has a remarkable capacity to concentrate KOH, even in an alkaline bath of concentration 3 M. The highest conductivity of KOH-doped PBI (9×10⁻² S cm⁻¹) at 25°C obtained in this work is higher than the we had obtained previously as optimum values for H₂SO₄-doped PBI (5 × 10⁻² S cm⁻¹ at 25°C) and H₃PO₄-doped PBI ( 2 × 10⁻³ S cm⁻¹ at 25°C). PEMFCs based on an alkali-doped PBI membrane were demonstrated, and their characteristics exhibited the same performance as those of PEMFCs based on Nafion® 117. Their development is currently under active investigation.     

Self-assembled Li4Ti5O12/TiO2/Li3PO4 for integrated Li–ion microbatteries

This work aims to maximize the number of active sites for energy storage per geometric area, by approaching the investigation to 3D design for microelectrode arrays. Self-organized Li₄Ti₅O₁₂/TiO₂/Li₃PO₄ composite nanoforest layer (LTL) is obtained from a layer of self organized TiO₂/Li₃PO₄ nanotubes. The electrochemical response of this thin film electrode prepared at 700 °C exhibited lithium insertion and de-insertion at 1.55 and 1.57 V respectively, which is the typical potential found for lithium titanates. The effects of lithium phosphate on lithium titanate are explored for the first time. By cycling between 2.7 and 0.75 V the LTL/LiFePO₄ full cell delivered 145 mA h g^− 1 at an average potential of 1.85 V leading to an energy density of 260 W h kg^− 1 at C/2. Raman spectroscopy revealed that the γ-Li₃PO₄/lithium titanate structure is preserved after prolonged cycling. This means that Li₃PO₄ plays an important role for enhancing the electronic conductivity and lithium ion diffusion.     

Influence of iron on the synthesis and stability of yttrium silicate apatite

The stability of yttrium silicate apatite has been investigated by studying the influence of iron as a “stabilising cation” and also by using different synthesis routes. The formation of apatite in samples has been followed by X-ray diffraction and by ²⁹Si MAS NMR spectroscopy. The apatite phase appears to be stable at high temperatures (≈1700 °C) especially when heated in a nitrogen atmosphere; it can also occur in a metastable state when heated in air at lower temperatures; ≈1600 °C if prepared from a Y₂O₃SiO₂ mixture or in the range 950 °C <T< 1150 °C if synthesised by the sol–gel process. Longer heat-treatments result in its decomposition into Y₂Si₂O₇ and Y₂SiO₅. Iron appears to have two roles depending on the temperature; it stabilises the apatite phase at high temperatures when produced by the sol–gel route and catalyses the decomposition of sol–gel derived apatite at low temperatures.     

Electrode properties of Sr doped La2CuO4 as new cathode material for intermediate-temperature SOFCs

High performance La_2−xSr_xCuO_4−δ (x = 0.1, 0.3, 0.5) cathode materials for intermediate temperature solid oxide fuel cell (IT-SOFCs) were prepared and characterized. The investigation of electrical properties indicated that La_1.7Sr_0.3CuO₄ cathode has low area specific resistance (ASR) of 0.16 Ω cm² at 700 °C and 1.2 Ω cm² at 500 °C in air. The rate-limiting step for oxygen reduction reaction on La_1.7Sr_0.3CuO₄ electrode changed with oxygen partial pressure and measurement temperature. La_1.7Sr_0.3CuO₄ cathode exhibits the lowest overpotential of about 100 mV at a current density of 150 mA cm⁻² at 700 °C in air.     

Formation and characterization of magnetic barium ferrite hollow fibers with high specific surface area via sol–gel process

The magnetic barium ferrite (BaFe₁₂O₁₉) hollow fibers with a high specific surface area about 22–38 m² g^?1, diameters around 1 μm and a ratio of the hollow diameter to the fiber diameter estimated about 1/2–2/3 have been prepared by the gel-precursor transformation process. The precursor and resulting ferrite hollow fibers were analyzed by thermo-gravimetric and differential scanning calorimetry, infrared spectroscopy, scanning electron microscopy and X-ray diffraction. The specific surface area was measured by the Brunauer–Emmett–Teller method. The gel formed at pH 5.5 has a good spinnability. A pure barium ferrite phase is formed after calcined at 750 °C for 2 h and fabricated of nanograins about 38 nm with a hexagonal plate-like morphology, which are increased to about 72 nm with the calcination temperature increased up to 1050 °C. The barium ferrite hollow fibers obtained at 750 °C for 2 h have a specific surface area 38.1 m² g^?1 and average pore size 6.5 nm and then the specific surface area and average pore size show a reduction tendency with the calcination temperature increasing from 750 to 1050 °C owing to the particle growth and fiber densification. These barium ferrite hollow fibers exhibit typical hard-magnetic materials characteristics and the formation mechanism for hollow structures is discussed.     

LiMn2O4 hollow nanosphere electrode material with excellent cycling reversibility and rate capability

Lithium-rich Li_1.05Mn₂O₄ hollow nanospheres have been successfully prepared by air-calcining lithiated MnO₂ precursor at a low temperature of 550 °C, which was synthesized by chemical lithiation of hollow MnO₂ nanospheres with LiI at 70 °C for 12 h. The lithium-rich Li_1.05Mn₂O₄ hollow nanospheres exhibit an excellent cycling stability and rate capability as a cathode material for rechargeable lithium batteries: it maintains 90% of its initial capacity after 500 cycles, and keeps 70% of the reversible capacity at 0.1 C rat, even at 15 C rate.     

Thermal degradation and evolved gas analysis: A polymeric blend of urea formaldehyde (UF) and epoxy (DGEBA) resin

A polymeric blend has been prepared using urea formaldehyde (UF) and epoxy (DGEBA) resin in 1:1 mass ratio. The thermal degradation of UF/epoxy resin blend (UFE) was investigated by using thermogravimetric analyses (TGA), coupled with FTIR and MS. The results of TGA revealed that the pyrolysis process can be divided into three stages: drying process, fast thermal decomposition and cracking of the sample. There were no solid products except ash content for UFE during combustion at high temperature. The total mass loss during pyrolysis at 775 °C is found to be 97.32%, while 54.14% of the original mass was lost in the second stage between 225 °C and 400 °C. It is observed that the activation energy of the second stage degradation during combustion (6.23 × 10⁻⁴ J mol⁻¹) is more than that of pyrolysis (5.89 × 10⁻⁴ J mol⁻¹). The emissions of CO₂, CO, H₂O, HCN, HNCO, and NH₃ are identified during thermal degradation of UFE.     

Preparation via microemulsion method and proton conduction at intermediate-temperature of BaCe1−xYxO3−α

The ceramic powders of BaCe_1?xY_xO_3?α (x = 0.05, 0.10, 0.15, 0.20) have been prepared via a microemulsion method. Green compacts of the powders were sintered to densities higher than 95% of theoretical at the lower temperature (1500 °C). The obtained ceramics showed a single-phase of orthorhombic perovskite. The proton conduction was investigated by employing the techniques of AC impedance and electrochemical hydrogen permeation (hydrogen pumping) at 300–600 °C. It was found that the ceramics were almost pure proton conductors in wet hydrogen, and the highest proton conductivity was observed for x = 0.15 at 600 °C. Ammonia was synthesized successfully from nitrogen and hydrogen at atmospheric pressure in the electrolytic cell using BaCe_0.85Y_0.15O_3?α. The maximum rate of NH₃ formation was found to be 2.1 × 10^?9 mol s^?1 cm^?2 at 500 °C with an applied current of 0.75 mA.     

Li0.93[Li0.21Co0.28Mn0.51]O2 nanoparticles for lithium battery cathode material made by cationic exchange from K-birnessite

Li_0.93[Li_0.21Co_0.28Mn _0.51]O₂ nanoparticles with an R-3m space group is hydrothermally prepared from Co_0.35Mn_0.65O₂ obtained from an ion-exchange reaction with K-birnessite K_0.32MnO₂ at 200 °C. Even at a hydrothermal reaction temperature of 150 °C, the spinel (Fd3m) phase is dominant, and a layered phase became dominant by combining an increase in the temperature to 200 °C with an increase in lithium concentration. The as-prepared cathode particle has plate-like hexagonal morphology with a size of 100 nm and thickness of 20 nm. The first discharge capacity of the cathode is 258 mAh/g with an irreversible capacity ratio of 22%, and the capacity retention after 30 cycles is 95% without developing a plateau at ∼3 V. Capacity retention of the cathode discharge is 84% at 4C rate (=1000 mA/g) and shows full capacity recovery when decreasing the C rate to 0.1 C.     

Cyanamide-derived non-precious metal catalyst for oxygen reduction

Cyanamide was used in the preparation series of metal–nitrogen–carbon (M–N–C) oxygen reduction catalysts. The best catalyst, treated at 1050 °C, shows good performance versus previously reported non-precious metal catalysts with an OCV ~ 1.0 V and a current density of 105 mA/cm² (iR-corrected) at 0.80 V in H₂/O₂ fuel cell testing (catalyst loading: 4 mg cm^? 2). Although nitrogen content has been previously correlated positively with ORR activity, no such trend is observed here for any nitrogen type. The combined effects of nitrogen and sulfur incorporation into the carbon may account for the high activity of the 1050 °C catalyst.     

Development of novel low-temperature SOFCs with co-ionic conducting SDC-carbonate composite electrolytes

A series of ceria-based composite materials consisting of samaria doped ceria (SDC) and binary carbonates(Li₂CO₃–Na₂CO₃) were examined as functional electrolytes for low-temperature solid oxide fuel cells (SOFCs). DTA and SEM techniques were applied to characterize the phase- and micro-structural properties of the composite materials. Conductivity measurements were carried on the composite electrolytes with a.c. impedance in air. A transition of ionic conductivity with temperature was occurred among all samples with different carbonate content, which related to the interface phase. Single cells based on the composite electrolytes, NiO as anode and lithiated NiO as cathode, were fabricated by a simple dry-pressing process and tested at 400–600 °C. The maximum output power at 600 °C increased with the carbonate content in the composite electrolytes, and reached the maximum at 25 wt.%, then decreased. Similar trend has also shown at 500 °C, but the maximum was obtained at 20wt.%. The best performances of 1085 mW cm⁻² at 600 °C and 690 mW cm⁻² at 500 °C were achieved for the composite electrolytes containing 25 and 20 wt.% carbonates, respectively. During fuel cell operation, it found that the SDC-carbonate composites are co-ionic (O²⁻/H⁺) conductors. At lower carbonate contents, both oxide–ion and proton conductions were significant, when the content increased to 20–35 wt.%, proton conduction dominated. The detailed conduction mechanism in these composites needs further investigation.     

Structural and electrochemical investigation of Li2MgSnO4 anode for lithium batteries

Hexagonal Li₂MgSnO₄ compound was synthesized at 800 °C using Urea Assisted Combustion (UAC) method and the same has been exploited as an anode material for lithium battery applications. Structural investigations through X-ray diffraction, Fourier Transform Infra Red spectroscopy and ⁷Li NMR (Nuclear Magnetic Resonance spectroscopy) studies demonstrated the existence of hexagonal crystallite structure with a = 6.10 and c = 9.75. An average crystallite size of ∼400 nm has been calculated from PXRD pattern, which was further evidenced by SEM images. An initial discharge capacity of ∼794 mA h/g has been delivered by Li₂MgSnO₄ anode with an excellent capacity retention (85%) and an enhanced coulombic efficiency (97–99%). Further, the Li₂MgSnO₄ anode material has exhibited a steady state reversible capacity of ∼590 mA h/g even after 30 cycles, thus qualifying the same for use in futuristic lithium battery applications.