Synthesis,characterization and electrocatalytic activity for ethanol oxidation of carbon supported Pt,Pt–Rh,Pt–SnO2 and Pt–Rh–SnO2 nanoclusters

Nanoclusters of Pt, Pt–Rh, Pt–SnO₂ and Pt–Rh–SnO₂ were successfully synthesized by polyol method and deposited on high-area carbon. HRTEM and XRD analysis revealed two phases in the ternary Pt–Rh–SnO₂/C catalyst: solid solution of Rh in Pt and SnO₂. The activity of Pt–Rh–SnO₂/C for ethanol oxidation was found to be much higher than Pt/C and Pt–Rh/C and also superior to Pt–SnO₂/C. Quasi steady-state measurements at various temperatures (30–60 °C), ethanol concentrations (0.01–1 M) and H₂SO₄ concentrations (0.02–0.5 M) showed that Pt–Rh–SnO₂/C is about 20 times more active than Pt/C in the potential range of interest for the fuel cell application.     

Preparation and electrocatalytic activity of Rh adlayers on Pt(1 0 0) electrodes: reduction of nitrous oxide

Rhodium adlayers (submonolayer range) have been prepared on Pt(1 0 0) electrodes by electrodeposition from acidic solutions containing an excess of chloride. These Rh/Pt(1 0 0) electrodes give a well-defined voltammetric signal in the hydrogen adsorption region, which gives evidence of a high level of order in the Rh adlayer and allow a reliable estimation of the coverage. The voltammetric behavior of the Rh/Pt(1 0 0) electrodes points to an epitaxial growth with formation of rhodium islands. The well-ordered bimetallic surfaces freshly prepared were tested as electrocatalysts for nitrous oxide reduction and the responses were compared with those of the bulk Pt(1 0 0) and Rh(1 0 0) electrodes. The voltammogram for the bimetallic surface showed well separated N₂O reduction signals for Rh and Pt surface zones. An exceptionally high electrocatalytic activity for the Rh adlayer was found for low coverages. This behavior is explained on the basis of a high activity of the rhodium adatoms in the periphery of the islands.     

Influence of rhodium additive on hydrogen electrosorption in palladium-rich Pd–Rh alloys

Hydrogen electrosorption into Pd-rich (>80 at.% Pd in the bulk) Pd–Rh alloys has been studied in acidic solutions (0.5 M H₂SO₄) using cyclic voltammetry and chronoamperometry. The influence of temperature (in the range between 283 and 328 K), electrode potential and alloy bulk composition on hydrogen electrosorption properties of Pd–Rh alloys is presented. It has been found that the additive of Rh to Pd–Rh alloys increases the maximum hydrogen solubility (for Rh bulk content below 10 at.%), decreases the potential of absorbed hydrogen oxidation peak and decreases the potential of the α → β phase transition. Increasing temperature decreases the potential of absorbed hydrogen oxidation peak, the maximum hydrogen solubility, and the potential of the α → β phase transition. The amounts of electrosorbed hydrogen for α- and β-phase boundaries, i.e., α_max and β_min, have been determined from the integration of the initial parts of current–time responses in hydrogen absorption and desorption processes. The H/M ratio corresponding to α_max increases with increasing Rh content, while for β_min a maximum of H/M ratio is observed for the alloys containing ca. 95% Rh.

     

Hydrodechlorination of CCl4 over carbon-supported palladium–gold catalysts prepared by the reverse “water-in-oil” microemulsion method

Two series of carbon-supported Pd–Au catalysts were prepared by the reverse “water-in-oil, W/O” method, characterized by various techniques and investigated in the reaction of tetrachloromethane with hydrogen at 423 K. The synthesized nanoparticles were reasonably monodispersed having an average diameter of 4–6 nm (Pd/C and Pd–Au/C) and 9 nm (Au/C). Monometallic palladium catalysts quickly deactivated during the hydrodehalogenation of CCl₄. Palladium–gold catalysts with molar ratio Pd:Au = 90:10 and 85:15 were stable and much more active than the monometallic palladium and Au-richer Pd–Au catalysts. The selectivity toward chlorine-free hydrocarbons (especially for C₂₊ hydrocarbons) was increased upon introducing small amounts of gold to palladium. Simultaneously, for the most active Pd–Au catalysts, the selectivity for undesired dimers C₂H_xCl_y, which are considered as coke precursors, was much lower than for monometallic Pd catalysts. Reasons for synergistic effects are discussed. During CCl₄ hydrodechlorination the Pd/C and Pd–Au/C catalysts were subjected to bulk carbiding.     

A study of Pt–Pd/γ-Al2O3 catalysts for methane oxidation resistant to deactivation by sulfur poisoning

The catalytic oxidation of methane was studied over calcined and reduced Pt–Pd/γ-Al₂O₃ catalysts, in the presence and the absence of SO₂ in the CH₄–O₂ reaction feed. The effect of sulfation (SO₂ + O₂ for 4 h at 500 °C) was also studied on the catalyst resistance to deactivation by sulfur poisoning. Sulfating the calcined Pt–Pd/γ-Al₂O₃ catalysts resulted in a strong deactivation for the CH₄–O₂ reaction. However, the catalytic activity of the reduced-sulfated Pt–Pd/γ-Al₂O₃ catalyst for CH₄–O₂ reaction remained rather unaffected in the presence and in the absence of SO₂ in the reaction feed. XPS analysis revealed, over reduced-sulfated Pt–Pd/γ-Al₂O₃ catalysts, the presence of Pt(0) metallic surface species on which SO₂ interactions may be faster related to Pd surface species. The presence of Pt(0) may be necessary to prevent the interactions between SO₂ and Pd surface species. Long time catalytic tests showed that the activity of a reduced Pt–Pd/γ-Al₂O₃ catalysts for CH₄–O₂ reactions remained rather unaffected despite the presence of SO₂ in the reaction feed.     

Oxygen reduction reaction on the low index planes of palladium electrodes modified with a monolayer of platinum film

Oxygen reduction reaction (ORR) has been studied on the low index planes of Pd modified with a monolayer of Pt (Pt/Pd(hkl)) in 0.1 M HClO₄ with the use of hanging meniscus rotating disk electrode. The activity for ORR on bare Pd(hkl) electrode depends on the surface structure strongly, however, voltammograms of ORR on Pt/Pd(hkl) electrodes do not depend on the crystal orientation. The specific activities of Pt/Pd(hkl) electrodes at 0.90 V (RHE) are higher than that on Pt(1 1 0) which has the highest activity for ORR in the low index planes of Pt. The mass activity on Pt/Pd(hkl) electrode is 7 times as high as a commercial Pt/C catalyst.     

Evaluation of Pt40Pd60/MWCNT electrocatalyst as ethylene glycol-tolerant oxygen reduction cathodes

Pt–Pd/MWCNT with Pt:Pd atomic ratio 40:60 and Pt/MWCNT electrocatalyst were synthesized and evaluated as oxygen reduction reaction (ORR) cathodes for Direct Ethylene Glycol Fuel Cells (DEGFC) applications. As reference, a commercial Pt/C material was also tested. We found that Pt–Pd/MWCNT has high tolerance capability to EG and higher selectivity for the ORR compared to the Pt-alone materials. As a result, the shift in onset potential for the ORR, E_onset, at Pt–Pd/MWCNT was considerably smaller than the shift at Pt/MWCNT or Pt/C. The average particle size (from XRD) was 3.5 and 4 nm for Pt/MWCNT and Pt–Pd/MWCNT, respectively. A moderate degree of alloying was determined for the Pt–Pd material. An advantageous application of Pt–Pd electrocatalysts should be in DEGFCs.     

Synthesis and catalytic properties of cationic palladium(II) and rhodium(I) complexes bearing diphosphinidinecyclobutene ligands

Cationic palladium(II) and rhodium(I) complexes bearing 1,2-diaryl-3,4-bis[(2,4,6-tri-t-butylphenyl)phosphinidene]cyclobutene ligands (DPCB–Y) were prepared and their structures and catalytic activity were examined (aryl = phenyl (DPCB), 4-methoxyphenyl (DPCB–OMe), 4-(trifluoromethyl)phenyl (DPCB–CF₃)). The palladium complexes [Pd(MeCN)₂(DPCB–Y)]X₂ (X = OTf, BF₄, BAr₄ (Ar = 3,5-bis(trifluoromethyl)phenyl)) were prepared by the reactions of DPCB–Y with [Pd(MeCN)₄]X₂, which were generated from Pd(OAc)₂ and HX in MeCN. On the other hand, the rhodium complexes [Rh(MeCN)₂(DPCB–Y)]OTf were prepared by the treatment of [Rh(μ-Cl)(cyclooctene)₂]₂ with DPCB–Y in CH₂Cl₂, followed by treatment with AgOTf in the presence of MeCN. The cationic complexes catalyzed conjugate addition of benzyl carbamate to α,β-unsaturated ketones.     

Oxygen reduction reaction on carbon supported Palladium–Nickel alloys in alkaline media

Carbon supported Palladium–Nickel alloys with various compositions (Pd–Ni/C) were synthesized by chemical reduction of the co-precipitated Pd and Ni hydroxides on carbon. The structure of these alloys was characterized using X-ray diffraction (XRD) analysis. The catalytic activity of Pd–Ni/C for oxygen reduction reaction (ORR) in alkaline media was studied using a glassy carbon rotating disk electrode (RDE). Pd/C showed ORR activity close to that of Pt/C. The activities of Pd–Ni (3:1)/C and Pd–Ni (1:1)/C were found unchanged compared with that of Pd/C. Ni/C showed about 175 mV lower onset potential than Pt/C, and the activity of Pd–Ni (1:3)/C was observed to be between that of Pd/C and Ni/C.     

Effect of hydrogen-sulfide on the hydrogen permeance of palladium–copper alloys at elevated temperatures

The hydrogen permeance of several 0.1 mm thick Pd–Cu alloy foils (80 wt.% Pd–20 wt.% Cu, 60 wt.% Pd–40 wt.% Cu and 53 wt.% Pd–47 wt.% Cu) was evaluated using transient flux measurements at temperatures ranging from 603 to 1123 K and pressures up to 620 kPa both in the presence and absence of 1000 ppm H₂S. Sulfur resistance, as evidenced by no significant change in permeance, was correlated with the temperatures associated with the face-centered-cubic crystalline structure for the alloys in this study. The permeance of the body-centered cubic phase, however, was up to two orders of magnitude lower when exposed to H₂S. A smooth transition from sulfur poisoning to sulfur resistance with increasing temperature was correlated with the alloy transition from a body-centered-cubic structure to a face-centered-cubic structure.     

Pd/Pt core–shell nanowire arrays as highly effective electrocatalysts for methanol electrooxidation in direct methanol fuel cells

Highly ordered Pd/Pt–core–shell nanowire arrays (Pd/Pt NWAs) have been prepared by anodized aluminum oxide (AAO) template-electrodeposition and magnetron sputtering methods. Pd/Pt NWA electrode shows a very high electrochemical active surface area and high electrocatalytic activity for the methanol electrooxidation in acid medium for direct methanol fuel cells (DMFCs). The mass specific anodic peak current density is 756.7 mA mg⁻¹ Pt for the methanol oxidation on the Pd/Pt NWA electrode, an increase by a factor of four as compared to conventional E-TEK PtRu/C electrocatalysts. The mechanism of the significant enhancement of the Pd/Pt core/shell NWA nanostructure in the efficiency and electrocatalytic activity of Pt for the methanol electrooxidation in acid medium is discussed.     

pH effect on electrocatalytic reduction of CO2 over Pd and Pt nanoparticles

Adsorbed hydrogen participates in electrocatalytic reduction of CO₂ and competitive hydrogen evolution reaction (HER) simultaneously, and its reaction pathway greatly affects the activity and selectivity of CO₂ reduction. In this work, we investigate pH effect on electrocatalytic reduction of CO₂ over Pd and Pt nanoparticles (NPs) with a similar size in a pH range from 1.5 to 4.2. Pt NPs completely contribute to HER in the pH range. Over Pd NPs, Faradaic efficiency for CO production at − 1.19 V (vs. reversible hydrogen electrode) varies from 3.2% at pH of 1.5 to 93.2% at pH of 4.2, and current density for CO production reaches maximum at pH of 2.2. The significant enhancement of Faradaic efficiency and current density for CO production over Pd NPs at high pH values is attributed to decreased kinetics of hydrogen evolution reaction by increasing hydrogen binding energy and lowered adsorption affinity of CO-like intermediate compared to Pt.     

Influence of rhodium additive on hydrogen electrosorption in palladium-rich Pd�CRh alloys

Hydrogen electrosorption into Pd-rich (>80?at.% Pd in the bulk) Pd?CRh alloys has been studied in acidic solutions (0.5?M H₂SO₄) using cyclic voltammetry and chronoamperometry. The influence of temperature (in the range between 283 and 328?K), electrode potential and alloy bulk composition on hydrogen electrosorption properties of Pd?CRh alloys is presented. It has been found that the additive of Rh to Pd?CRh alloys increases the maximum hydrogen solubility (for Rh bulk content below 10?at.%), decreases the potential of absorbed hydrogen oxidation peak and decreases the potential of the ???????? phase transition. Increasing temperature decreases the potential of absorbed hydrogen oxidation peak, the maximum hydrogen solubility, and the potential of the ???????? phase transition. The amounts of electrosorbed hydrogen for ??- and ??-phase boundaries, i.e., ??_max and ??_min, have been determined from the integration of the initial parts of current?Ctime responses in hydrogen absorption and desorption processes. The H/M ratio corresponding to ??_max increases with increasing Rh content, while for ??_min a maximum of H/M ratio is observed for the alloys containing ca. 95% Rh.     

Improvement of hydrogen isotope exchange reactions on Li4SiO4 ceramic pebble by catalytic metals

Li4SiO4 ceramic pebble is considered as a candidate tritium breeding material of Chinese Helium Cooled Solid Breeder Test Blanket Module(CH HCSB TBM) for the International Thermonuclear Experimental Reactor(ITER).In this paper,Li4SiO4 ceramic pebbles deposited with catalytic metals,including Pt,Pd,Ru and Ir,were prepared by wet impregnation method.The metal particles on Li4SiO4 pebble exhibit a good promotion of hydrogen isotope exchange reactions in H 2-D 2 O gas system,with conversion equilibrium temperature reduction of 200-300 8C.The out-of-pile tritium release experiments were performed using 1.0 wt% Pt/Li4SiO4 and Li 4 SiO 4 pebbles irradiated in a thermal neutron reactor.The thermal desorption spectroscopy shows that Pt was effective to increase the tritium release rate at lower temperatures,and the ratio of tritium molecule(HT) to tritiated water(HTO) of 1.0 wt% Pt/Li4SiO4 was much more than that of Li4SiO4,which released mainly as HTO.Thus,catalytic metals deposited on Li4SiO4 pebble may help to accelerate the recovery of bred tritium particularly in low temperature region,and increase the tritium molecule form released from the tritium breeding materials.     

Reduction of aromatic compounds with Al powder using noble metal catalysts in water under mild reaction conditions

In water, Al powder becomes a powerful reducing agent, transforming in cyclohexyl either one or both benzene rings of aromatic compounds such as biphenyl, fluorene and 9,10-dihydroanthracene under mild reaction conditions in the presence of noble metal catalysts, such as Pd/C, Rh/C, Pt/C, or Ru/C. The reaction is carried out in a sealed tube, without the use of any organic solvent, at low temperature. Partial aromatic ring reduction was observed when using Pd/C, the reaction conditions being 24 h and 60 °C. The complete reduction process of both aromatic rings required 12 h and 80 °C with Al powder in the presence of Pt/C.     

Catalytic oxidation of volatile organic compounds (VOCs). Oxidation of o-xylene over Pd and Pt/HFAU catalysts

The transformation of o-xylene in low concentration (1 700 ppmv) into air was investigated over Pd and Pt/HFAU catalysts (framework Si/Al ratio equal to 17 and 100). Whatever the catalyst, o-xylene oxidation into CO₂ and H₂O is accompanied by the retention within the zeolite pores of heavy compounds (‘coke’). The relative significance of these reactions depends on the operating conditions (temperature, time-on-stream) and on the catalyst characteristics (Pd or Pt, Si/Al ratio). Over Pt and Pd/HFAU(17), time-on-stream has a positive effect on the xylene oxidation apparently related to the reducibility of Pd and Pt species during the reaction. The higher activity of Pt/HFAU catalysts can be attributed to its greater number of active species (especially Pt⁰). Those active species can be more rapidly formed than Pd⁰ by auto reduction during the calcination of Pt precursor. Whatever the metal, the higher the Si/Al ratio of the support, the faster the xylene oxidation and the lower the coke formation. This can be related to the higher proportion of reduced species (Pd⁰ and Pt⁰) formed on the more dealuminated catalyst but also to the hydrophobicity of the support. Indeed, the hydrophobicity of the zeolite play a positive role in the oxidation activity in presence of steam; the higher the Si/Al ratio of the zeolite, the faster the o-xylene oxidation. Thus a catalyst with a low platinum content supported on a hydrophobic zeolite (0.10 Pt/HFAU(100)) allows to oxidising totally o-xylene at 210 °C in presence of steam.     

Comparative theoretical study of the structure and bonding of propyne on the Pt(1 1 1) and Pd(1 1 1) surfaces

The interaction of propyne with the Pt(1 1 1) and Pd(1 1 1) surfaces has been studied by means of the generalised gradient approach of density functional theory using periodic slab models. For both surfaces, the most stable adsorption mode of propyne is di-σ/π mode where the hydrocarbon is σ-bonded to two metal atoms with some additional π bonding to a third adjacent surface atom. The adsorption geometry is a highly distorted propyne with the C₁ and C₂ in a nearly sp² hybridisation. Two equivalent surface structures have been found on Pt and Pd. These correspond to the adsorption on the fcc or hcp hollow sites. The adsorption energies on Pt(1 1 1) and Pd(1 1 1) are predicted to be ∼−197 and −161 kJ mol⁻¹, respectively. The electronic factors that control the chemisorption have been analysed by means of the projected density of states.     

Some aspects of metal-support strong interactions in Rh/Al2O3 catalyst under oxidising and reducing conditions

The aim of the Letter is to elucidate the nature of metal-support interaction in the 2 wt% Rh/Al₂O₃ catalyst obtained by annealing Rh–O–Al xerogel at 1113 K in air.XPS, HRTEM, and XRD results reveal that during the Rh–O–Al xerogel annealing in air, rhodium incorporates into forming alumina, which results mostly in Rh⁴⁺/δ-Al₂O₃ solid solution formation.However, in the course of the catalyst reduction at 773 with H₂ and at 823 K with CH₄ the Rh⁴⁺/δ-Al₂O₃ solid solution transforms into Rh–Al alloy. The islands of rhodium form on the surface of the Rh–Al alloy nanocrystallites if the reduction is slow enough.     

Preparation of a palladium alloy composite membrane supported in a porous stainless steel by vacuum electrodeposition

Pinhole-free palladium/nickel (Pd/Ni) alloy membranes deposited on a porous stainless steel (SUS) support have been fabricated. The deposition was made by vacuum electrodeposition technique which could produce the alloy film less than 1 μm thick. This technique allows for the Pd/Ni alloy by employing Pd/Ni complex reagent, and typical Pd/Ni plating had compositions of 78% Pd and 22% Ni. In order to make the surface smooth and enhance the adhesive bond between the top layer and the substrate, a nascent porous SUS disk was treated sequently with submicron nickel powder and CuCN solution. The important parameters that can affect deposition were pore size, defects, and surface roughness of substrate. The membranes were characterized by permeation experiments with hydrogen and nitrogen at temperatures ranging from 623 to 823 K and pressures from 10.3 to 51.7 cmHg. The composite membranes prepared in this technique yielded excellent separation performance for hydrogen: hydrogen permeance of 5.79×10⁻² cm³/cm² cmHg s and hydrogen/nitrogen (H₂/N₂) selectivity was 4700 at 823 K.     

Bismuth modified Pd/C as catalysts for hydrogen related reactions

The electrocatalytic activity of bimetallic BiPd catalysts supported on Sibunit carbon towards hydrogen oxidation/evolution reactions (HOR/HER) was studied in a gas diffusion electrode (GDE) setup. Catalysts were synthesized by deposition of Pd on the carbon support, followed by impregnation of Pd/C precursor with Bi(NO₃)₃ solution and reduction in hydrogen. Transmission electron microscopy and local EDX elemental analysis revealed that BiPd/C catalysts contain bimetallic particles with narrow size distribution with maxima at 3.2–4.1 nm. X-ray diffraction evidenced that bimetallic particles are constituted by Pd–Bi solid solution. It was shown that modification of Pd/C by bismuth increases the specific activity of palladium towards HOR/HER by a factor of 3.