Fast fabrication of Ta2O5 nanotube arrays and their conversion to Ta3N5 for efficient solar driven water splitting

This work shows that highly ordered and mechanically stable micrometer-long Ta₂O₅ nanotube arrays can be fabricated by galvanostatic anodization in a few seconds. Typically, ~ 7.7 μm long nanotubes can be grown at 1.2 A cm^− 2 in only 2 s. Such nanotubes can be converted to Ta₃N₅ nanotube arrays by nitridation. Photoelectrochemical (PEC) water splitting using AM 1.5G illumination yields for the Ta₃N₅ nanotube photoanode modified with cobalt phosphate (Co–Pi) remarkable photocurrents of 5.9 mA cm ⁻² at 1.23 V_RHE and 12.9 mA cm ⁻² at 1.59 V_RHE and after Ba-doping a value of 7.5 mA cm ⁻² at 1.23 V_RHE is obtained.     

Fabrication and supercapacitive performance of long anodic TiO2 nanotube arrays using constant current anodization

A galvanostatic anodization is used to prepare long TiO₂ nanotube arrays (TNTAs). TNTAs of over 100 μm in length, with similar nanotube size and structural regularity to the classic TNTAs made from potentiostatic mode, are achieved at 10 mA cm^− 2. After a post-anodization in a H₃PO₄-based electrolyte, the TNTAs with long nanotubes exhibit good adhesion to Ti substrate. The as-prepared long TNTAs yield a larger areal capacitance of 128.4 mF cm^− 2. Further, the long TNTAs possess a higher surface area, making them suitable as support templates for other active materials.     

Bubble-like CdSe nanoclusters sensitized TiO2 nanotube arrays for improvement in solar cell

Solar cells were fabricated using novel bubble-like CdSe nanoclusters sensitized highly ordered titanium oxide nanotube (TiO₂ NT) array, prepared by anodization technique. The CdSe sensitization of TiO₂ NT arrays was carried out by a chemical bath deposition method with freshly prepared sodium selenosufite, ammonium hydroxide and cadmium acetate dehydrate at different deposition times: 20, 40 and 60 min. The adsorption of CdSe nanoclusters on the upper and inner surface of the TiO₂ NT arrays has been confirmed by field emission scanning electron and transmission electron microscopes. The results show the variation in cell a performance with different deposition times (20, 40, and 60 min) of CdSe on TiO₂ NT arrays. The solar cell with CdSe, deposited for 60 min, shows reasonably high photovoltaic property compared to the reported results of similar studies. This solar cell shows the maximum photoelectric conversion efficiency of 1.56% (photocurrent of 7.19 mA/cm²; photovoltage of 0.438 V; and fill factor of 49.5%) and average incident photon to current efficiency of 50.2%. The photocurrent, incident photon-current efficiency and electron lifetime have been improved due to the increase of covered area and size of bubble-like CdSe nanoclusters on TiO₂ NT arrays with the increase of deposition time.     

Enhanced electrochemical performance of carbon-coated TiO2 nanobarbed fibers as anode material for lithium-ion batteries

We report the electrochemical performance of carbon-coated TiO₂ nanobarbed fibers (TiO₂@C NBFs) as anode material for lithium-ion batteries. The TiO₂@C NBFs are composed of TiO₂ nanorods grown on TiO₂ nanofibers as a core, coated with a carbon shell. These nanostructures form a conductive network showing high capacity and C-rate performance due to fast lithium-ion diffusion and effective electron transfer. The TiO₂@C NBFs show a specific reversible capacity of approximately 170 mAh g^− 1 after 200 cycles at a 0.5 A g^− 1 current density, and exhibit a discharge rate capability of 4 A g^− 1 while retaining a capacity of about 70 mAh g^− 1. The uniformly coated amorphous carbon layer plays an important role to improve the electrical conductivity during the lithiation–delithiation process.     

Activity and stability of horseradish peroxidase in hydrophilic room temperature ionic liquid and its application in non-aqueous biosensing

The activity and stability of horseradish peroxidase (HRP) were investigated in a hydrophilic room temperature ionic liquid 1-butyl-3-methylimidazolium tetrafluroborate ([bmim][BF₄]) by electrochemical methods. Although no detectable activity exhibited in anhydrous [bmim][BF₄], HRP was active in the presence of a small amount of water (4.53%, v/v). And its activity can be improved by immobilization in agarose hydrogel. The immobilized HRP possesses excellent activity at 65 °C. It remained 80.2% of its initial activity after being immersed for 10.5 h in an aqueous mixture of [bmim][BF₄] with some hydrogen peroxide (H₂O₂) under room temperature, implying extremely high stability. Moreover, the immobilized HRP was found to be very sensitive and stable in H₂O-containing [bmim][BF₄] for the detection of H₂O₂, with a wide linear range of 6.10 × 10⁻⁷ to 1.32 × 10⁻⁴ mol l⁻¹ and low detection limit of 1.0 × 10⁻⁷ mol l⁻¹.     

Visible LED light photoelectrochemical sensor for detection of L-Dopa based on oxygen reduction on TiO2 sensitized with iron phthalocyanine

The present work describes the development of a new strategy to photoelectrochemical detection of L-Dopa at low potential based on oxygen reduction on TiO₂ sensitized with iron phthalocyanine (FePc/TiO₂). The FePc/TiO₂ composite shows a photocurrent 10-fold higher than that of pure TiO₂ nanoparticles and it was 4-fold higher than that of FePc exploiting visible light. The band gaps of pure TiO₂ nanoparticles, FePc and FePc/TiO₂, calculated according to the Kubelka–Munk equation, were 3.22 eV, 3.11 eV and 2.82 eV, respectively. The FePc/TiO₂ composite showed a low charge transfer resistance in comparison to the photoelectrode modified with FePc or TiO₂. Under optimized conditions, the photoelectrochemical sensor shows a linear response range from 20 up to 190 μmol L^− 1 with a sensitivity of 31.8 μA L mmol^− 1 and limit of detection of 1.5 μmol L^− 1 for the detection of L-Dopa.     

Electrochemical properties of liquid electrolyte added quasi-solid state TiO2 dye-sensitized solar cells

In this study a process has been introduced to replace traditional liquid or solid electrolyte coatings on dye-sensitized photoelectrode in solar cells. This process has more efficient diffusion of electrolyte, hence higher sensitivity. Better interfacial contact between polymer electrolyte and TiO₂ photoelectrode had improved electrochemical response and ionic conductivity of cell. Conductivity of this electrode was 9.33 × 10⁻³ S cm⁻¹ (at room temperature), which is much higher than the using traditional process for addition of electrolytes. It has 0.68 V open-circuit voltage and 3.19 mA cm⁻² short-circuit current density. Energy conversion efficiency of this cell was about 37% higher than the cell developed with traditional processes under constant light intensity (45 mW cm⁻²).     

Novel poly (neutral red) nanowires as a sensitive electrochemical biosensing platform for hydrogen peroxide determination

Poly (neutral red) nanowires (PNRNWs) have been synthesized for the first time by the method of cyclic voltammetric electrodeposition using porous anodic aluminum oxide (AAO) template and were examined by scanning electron microscopy (SEM) and transmission electron microscope (TEM). Moreover, horseradish peroxidase (HRP) was encapsulated in situ in PNRNWs (denoted as PNRNWs–HRP) by electrochemical copolymerization for potential biosensor applications. The PNRNWs showed excellent efficiency of electron transfer between the HRP and the glassy carbon (GC) electrode for the reduction of H₂O₂ and the PNRNWs–HRP modified GC electrode showed to be excellent amperometric sensors for H₂O₂ at −0.1 V with a linear response range of 1 μM to 8 mM with a correlation coefficient of 0.996. The detection limit (S/N = 3) and the response time were determined to be 1 μM and <5 s and the high sensitivity is up to 318 μA mM⁻¹ cm⁻².     

Self-assembled Li4Ti5O12/TiO2/Li3PO4 for integrated Li–ion microbatteries

This work aims to maximize the number of active sites for energy storage per geometric area, by approaching the investigation to 3D design for microelectrode arrays. Self-organized Li₄Ti₅O₁₂/TiO₂/Li₃PO₄ composite nanoforest layer (LTL) is obtained from a layer of self organized TiO₂/Li₃PO₄ nanotubes. The electrochemical response of this thin film electrode prepared at 700 °C exhibited lithium insertion and de-insertion at 1.55 and 1.57 V respectively, which is the typical potential found for lithium titanates. The effects of lithium phosphate on lithium titanate are explored for the first time. By cycling between 2.7 and 0.75 V the LTL/LiFePO₄ full cell delivered 145 mA h g^− 1 at an average potential of 1.85 V leading to an energy density of 260 W h kg^− 1 at C/2. Raman spectroscopy revealed that the γ-Li₃PO₄/lithium titanate structure is preserved after prolonged cycling. This means that Li₃PO₄ plays an important role for enhancing the electronic conductivity and lithium ion diffusion.     

Enhanced electrochemiluminescence based on Ru(bpy)32+-doped silica nanoparticles and graphene composite for analysis of melamine in milk

A sensitive electrochemiluminescence (ECL) sensor for melamine analysis was fabricated based on Ru(bpy)₃²⁺-doped silica (Ru(bpy)₃²⁺@SiO₂) nanoparticles and graphene composite. Spherical Ru(bpy)₃²⁺@SiO₂ nanoparticles with uniform size about 55 nm were prepared by the reverse microemulsion method. Since per Ru(bpy)₃²⁺@SiO₂ nanoparticle encapsulated a great deal of Ru(bpy)₃²⁺, the ECL intensity has been greatly enhanced, which resulted in high sensitivity. Due to its extraordinary electric conductivity, graphene improved the conductivity and accelerated the electron transfer rate. In addition, graphene could work as electronic channel improving the efficient luminophor amount participating in the ECL reaction, which further enhanced the ECL signal. This proposed sensor was used to melamine analysis and the ECL intensity was proportional to logarithmic melamine concentration range from 1 × 10⁻¹³ M to 1 × 10⁻⁸ M with the detect limit as low as 1 × 10⁻¹³ M. In application to detect melamine in milk, satisfactory recoveries could be obtained, which indicated this sensor having potential application in melamine analysis in real samples.     

Electroenzymatic oxidation of polyaromatic hydrocarbons using chemical redox mediators in organic media

The bioelectrochemical oxidation of two polyaromatic hydrocarbons (PAH): anthracene (ANT) and pyrene (PYR), using horseradish peroxidase (HRP) resulting in the synthesis of photoactive polyaromatic quinones in organic media was studied. The electrochemical generation of hydrogen peroxide was compared with its direct addition in concentrations of up to 0.0012 mol L⁻¹. In addition, three different chemical redox mediators were evaluated: ABTS, thionin and ortho-aminophenol. In a reaction medium containing 30% acetone and ABTS as mediator with a molar ratio mediator/PAH of 1:10, HRP attained the highest level of oxidation of PAH (1 × 10⁻³ mol L⁻¹): ANT (94%) and PYR (91%), producing 9,10-anthraquinone and mainly 1,2 and 4,5-pyrenequinones, respectively.     

The Ti@MoOx nanorod array as a three dimensional film electrode for micro-supercapacitors

Ti@MoO_x core–shell nanorod arrays with diameters within 100 nm were fabricated by electrodepositing MoO_x on a Ti nanorod array prepared by oblique angle deposition. A high areal capacitance of 27 mF cm^− 2 and satisfactory cycling stability were obtained. After post-annealing, MoO₂ grains were introduced to enhance the rate capability, suggesting a potential pseudocapacitive micro-electrode.     

Functionalization of multi-walled carbon nanotubes with poly(amidoamine) dendrimer for mediator-free glucose biosensor

By grafting with poly(amidoamine) (PAMAM) dendrimer, novel carbon nanotube (CNT) nano-composites have been successfully prepared. The novel functionalized matrix with plenty amino groups circumvents the troublesome solubility problem of CNTs in solvents, especially in water, greatly expanding the scope of the application of carbon nanotubes. The GO_x and HRP immobilized CNT-PAMAM based on the functional CNTs was synthesized. The bi-enzymatic CNT-PAMAM nano-composites are highly dispersible in water and show very promising applications in the fabrication of mediator-free bi-enzymatic biosensors for sensitive detection of glucose. The cooperation of nano-composite between CNT and high dense GO_x and HRP results in very high sensitivity to glucose with a current response of 2200 nA mM⁻¹ and fast response (∼1 s). The modified electrode exhibits a wide linear response range for glucose from 4.0 μM to 1.2 mM (R = 0.9971, N = 15), with a detection limit of 2.5 μM. The negative electrode potential of −0.34 V is favorable for glucose detection in real samples without interference caused by other biomolecules.     

All-solid-state micro lithium-ion batteries fabricated by using dry polymer electrolyte with micro-phase separation structure

Micro-batteries were fabricated by using BAB block copolymer as dry polymer electrolyte, which consisted of polyethylene oxide and polystyrene and had relatively high ionic conductivity at room temperature. The micro-batteries were fabricated by a sol–gel method combined with micro-injection system. Two types of micro-battery were fabricated. One consists of a single cell and another of 3-cells connected in series. LiMn₂O₄ and Li_4/3Ti_5/3O₄ were used as active materials in positive and negative electrode, respectively. The micro-array batteries were operated at room temperature without any plasticizer in the polymer electrolyte. The operation voltages were 2.45 V and 7.40 V for a single cell and 3-cell array, respectively. The discharge capacities estimated from cyclic voltammetry measurements were 245 nA h for a single cell and 12.1 nA h for a 3-cell array, which corresponded to the energy densities of 8.48 μW h cm⁻² and 4.54 μW h cm⁻², respectively.     

Tio2@Sn core–shell nanotubes for fast and high density Li-ion storage material

TiO₂@Sn core–shell nanotube material prepared by thermal decomposition of SnCl₄ on TiO₂ nanotubes at 300 °C has been demonstrated superior Li-ion storage capability of 176 mA h/g even at high current rate of 4000 mA/g (charge and discharge of all TiO₂ within 5 min) in spite of using low carbon content (5 wt%). This value corresponds to volumetric energy densities of 317 mA h/cm³, and its value was 3.5-fold larger than that of the bare TiO₂ nanotubes.     

Controllable growth of gold nanowires and nanoactuators via high-frequency AC electrodeposition

An electrochemical deposition method using high-frequency alternating current (AC) signal is reported here for the in situ synthesis and assembly of Au nanowires and nanoactuators on microelectrodes without using any masks or templates. High conductivity of 3.79 ± 0.14 × 10⁷ Ω^− 1 m^− 1 is achieved on the Au nanowires assembled between electrodes. Au nanoactuators with expansion ratio of more than 500% can be fabricated at higher frequency. The actuators can act as claws to grab SiO₂ nanoparticles in a water solution when driven by an alternating electric field. Disconnected nanowires and nanoparticles which self-aligned around the electrodes were also obtained at lower gold ion concentration, indicating a different current transfer mode in AC electrodeposition.     

Photocatalytic degradation of paraquat and genotoxicity of its intermediate products

The photocatalytic degradation of paraquat (1,1-dimethyl-4,4′-bipyridylium dichloride) aqueous solutions in the presence of polycrystalline TiO₂ Degussa P25 irradiated by near-UV light was investigated. The substrate and total organic carbon concentrations were monitored by UV spectroscopy and TOC measurements, respectively: the complete photocatalytic mineralization of paraquat (20 ppm) was achieved after ca. 3 h of irradiation by using 0.4 g l⁻¹ of catalyst amount at natural pH (ca 5.8). On the contrary no significant photodegradation of paraquat was observed in the absence of TiO₂ under similar experimental conditions. To evaluate the genotoxicity of paraquat and its intermediates produced during heterogeneous photocatalytic treatment, in vitro tests such as Ames test, with and without rat liver microsomal fractions (S9 mix), and micronucleus test, were used. Results obtained with Salmonella typhimurium (strain TA100) showed that paraquat and photocatalytic products were unable to induce gene mutations when photocatalysis was used in the presence of the optimum amount of TiO₂, i.e. 0.4 g l⁻¹, whereas an increase of revertants his⁺ per plate was observed after 300 min irradiation in the presence of very low amount of TiO₂ (0.04 g l⁻¹). The negative results from micronucleus test suggest that mutagenic, but non-clastogenic, late intermediates of paraquat photo-oxidation were formed when the photocatalytic runs of paraquat degradation were carried out by using 0.04 g l⁻¹ of photocatalyst.     

A lotus root-like porous nanocomposite polymer electrolyte

A lotus root-like porous nanocomposite polymer electrolyte (NCPE) based on poly(vinylidene difluoride-co-hexafluoropropylene) [P(VDF-HFP)] copolymer and TiO₂ nanoparticles was easily prepared by a non-solvent induced phase separation (NIPS) process. The formation mechanism of the lotus root-like porous structure is explained by a qualitative ternary phase diagram. The resulting NCPE had a high ionic conductivity up to 1.21 × 10⁻³ S cm⁻¹ at room temperature, and exhibited a high electrochemical stability potential of 5.52 V (vs. Li/Li⁺), lithium ion transference number of 0.65 and 22.89 kJ mol⁻¹ for the apparent activation energy for transportation of ions. It is of great potential application in polymer lithium ion batteries.     

Voltammetric sensor for buzepide methiodide determination based on TiO2 nanoparticle-modified carbon paste electrode

In this work, we have prepared nano-material modified carbon paste electrode (CPE) for the sensing of an antidepressant, buzepide methiodide (BZP) by incorporating TiO₂ nanoparticles in carbon paste matrix. Electrochemical studies indicated that the TiO₂ nanoparticles efficiently increased the electron transfer kinetics between drug and the electrode. Compared with the nonmodified CPE, the TiO₂-modified CPE greatly enhances the oxidation signal of BZP with negative shift in peak potential. Based on this, we have proposed a sensitive, rapid and convenient electrochemical method for the determination of BZP. Under the optimized conditions, the oxidation peak current of BZP is found to be proportional to its concentration in the range of 5 × 10⁻⁸ to 5 × 10⁻⁵ M with a detection limit of 8.2 × 10⁻⁹ M. Finally, this sensing method was successfully applied for the determination of BZP in human blood serum and urine samples with good recoveries.