A solid-state pH sensor based on WO3-modified vertically aligned multiwalled carbon nanotubes

In this communication, a novel solid-state pH sensor based on WO₃/MWNTs nanocomposite electrode will be reported. WO₃ nanoparticles were homogeneously coated on vertically aligned MWNTs by magnetron sputtering. Potentiometric pH response of the WO₃/MWNTs electrode in Britton–Robinson buffers revealed a linear working range from pH 2 to12 with a slope of about ?41 mV pH^?1 and a response time less than 90 s. The stability of the electrode remained over a month. Moreover, the WO₃/MWNTs electrode displayed excellent anti-interference property. Compared to conventional pH sensors, the pH sensor based on WO₃/MWNTs nanocomposite electrode also showed excellent reproducibility, high stability and superb selectivity.     

Gold nanoparticles integrated in a nanotube array for electrochemical detection of glucose

An enzyme-free amperometric glucose sensor of gold nanoparticle-constituted nanotube array electrode is presented. The resulted gold nanotube array electrode with significantly enhanced surface roughness shows prominent catalytic activity toward the electrooxidation of glucose in a pH 7.4 phosphate buffer (PBS) solution and thus can be used to individually or simultaneously determine glucose and the common interfering molecule of ascorbic acid (AA). In the case of glucose detection, the amperometric responses show a linear relationship to glucose concentration in the range of 1 mM–42.5 mM with a detection limit down to 10 μM. The present non-enzymatic glucose electrochemical biosensor shows a good stability and reproducibility.     

Low potential detection of nicotine at multiwalled carbon nanotube–alumina-coated silica nanocomposite

Electrocatalytic oxidation of nicotine at multiwalled carbon nanotube (MWCNT)–alumina-coated silica (ACS) nanocomposite modified glassy carbon electrode are described. The sensing performance of the MWCNT–ACS nanocomposite modified glassy carbon electrode for the electrooxidation of nicotine was investigated using cyclic voltammetry and amperometry in 0.1 M phosphate buffer solution (pH 8). The MWCNT–ACS nanocomposite modified glassy carbon electrode exhibited the abilities to decrease the electrooxidation potential, to prevent the electrode surface fouling, and to raise the current responses. The MWCNT–ACS nanocomposite responded rapidly to nicotine with a sensitivity of 1.786 A M^?1 cm^?2 and a detection limit of 1.42 μM (according to 3σ criterion). A signal almost 180 times more sensitive was obtained at MWCNT–ACS nanocomposite modified glassy carbon electrodes as compared to bare glassy carbon electrode. The nicotine oxidation potential obtained in this study is much lower than that at boron-doped diamond electrodes.     

Carbon black as successful screen-printed electrode modifier for phenolic compound detection

We report a miniaturized and disposable electrochemical sensor for phenolic compound detection. The sensor was constructed by modifying the working electrode surface of screen-printed electrode (SPE) with carbon black (CB) dispersion. This new probe showed higher sensitivity and better resistance to fouling than the bare SPE, displaying the suitability of CB as an excellent nanomodifier of SPE for phenolic compound detection. Catechol, gallic acid, caffeic acid, and tyrosol were detected by square wave voltammetry with a detection limit of 0.1 μM, 1 μM, 0.8 μM, and 2 μM, respectively. The sensor was able to selectively discriminate the mono-phenols and ortho-diphenols with rapid and easy measurement, paving the way to use a cost-effective device for quality control of foods and beverages containing phenolic compounds.     

Simultaneous determination of dopamine,ascorbic acid and uric acid with electrospun carbon nanofibers modified electrode

A novel carbon-nanofiber-modified carbon-paste electrode (CNF-CPE) was employed for the simultaneous determination of dopamine (DA), ascorbic acid (AA) and uric acid (UA) with good selectivity and high sensitivity. The CNFs were prepared by combination of electrospinning technique with thermal treatment method and were used without any pretreatment. In application to determination of DA, AA and UA in the ternary mixture, the pristine CNF-CPE exhibited well-separated differential pulse voltammetric peaks with high catalytic current. Low detection limits of 0.04 μM, 2 μM and 0.2 μM for DA, AA and UA were obtained, with the linear calibration curves over the concentration range 0.04–5.6 μM, 2–64 μM and 0.8–16.8 μM, respectively.     

Multilayer structured carbon nanotubes/poly-l-lysine/laccase composite cathode for glucose/O2 biofuel cell

Multilayer film of laccase, poly-l-lysine (PLL) and multi-walled carbon nanotubes (MWNTs) were prepared by a layer-by-layer self-assembly technique. The results of the UV–vis spectroscopy and scanning electron microscopy studies demonstrated a uniform growth of the multilayer. The catalytic behavior of the modified electrode was investigated. The (MWNTs/PLL/laccase)_n multilayer modified electrode catalyzed four-electron reduction of O₂ to water, without any mediator. The possible application of the laccase-catalyzed O₂ reduction at the (MWNTs/PLL/laccase)_n multilayer modified ITO electrode was illustrated by constructing a glucose/O₂ biofuel cell with the (MWNTs/thionine/AuNPs)₈ GDH film modified ITO electrode as a bioanode and the (MWNTs/PLL/laccase)₁₅ film modified ITO electrode as a biocathode. The open-circuit voltage reached to 700 mV, and the maximum power density achieved 329 μW cm⁻² at 470 mV of the cell voltage.     

Noncovalent nanoassembly of porphyrin on single-walled carbon nanotubes for electrocatalytic reduction of nitric oxide and oxygen

Water-soluble iron(III) meso-tetrakis(N-methylpyridinum-4-yl)porphyrin (FeTMPyP) was successfully immobilized on single-walled carbon nanotubes (SWNTs) via 1-pyrenebutyric acid (PBA). The formed SWNTs/PBA/FeTMPyP film showed an enhanced electrocatalytic peak at −0.70 V and −0.17 V towards reduction of nitric oxide and oxygen, respectively. SWNTs accelerated the electron transfer between FeTMPyP and electrode, and increased the amount of FeTMPyP adsorbed. FeTMPyP acted as a catalyst to decrease the reduction potential, exhibiting a synergy in electrocatalysis. The excellent electrocatalytic behaviors made SWNTs/porphyrin nanocomposite have a promising potential in fabricating new type of biosensors.     

Transparent and flexible glucose biosensor via layer-by-layer assembly of multi-wall carbon nanotubes and glucose oxidase

This paper reports a transparent and flexible glucose biosensor of which multi-wall carbon nanotubes (MWNTs) and glucose oxidase (GOx) is layer-by-layer (LBL) self-assembled on a polymer substrate. A thin Ti and Au layers is firstly deposited on the polymer substrate through plasma immersion ion implantation (PIII) and sputtering, respectively. An organic monolayer then forms on the gold surface using thiol chemistry. Subsequently, negatively charged MWNTs and GOx are stably LBL assembled on the modified Au surface, respectively, via alternative electrostatic interaction of the positively charged polyelectrolyte with the oppositely charged MWNTs and GOx. Electrochemical studies show that the multilayer membrane exhibits remarkable electrocatalytic activity to detect glucose molecule. The biosensor displays a linear response range of 0.02–2.2 mM (a correlation coefficient of 0.998) with a low detection limit of 10 μM. This remarkable performance, combined with the large area preparation process, demonstrates this CNT-based multilayer biosensor is well suited for commercial applications.     

Construction of an amperometric biosensor for xanthine via supramolecular associations

Xathine oxidase was chemically modified with β-cyclodextrin-branched carboxymethylcellulose and further supramolecularly immobilized on a gold electrode, previously coated with a monolayer of 1-adamantanyl residues. The electrode was employed for constructing an amperometric biosensor device, which showed linear response (poised at +700 mV vs. Ag/AgCl) toward xanthine concentration between 300 μM and 10.4 mM at pH 7.0. The biosensor reached 95% of steady-state current in about 14 s and its sensitivity was 8.2 mA/M cm². The enzyme electrode retained 93% of its initial activity after 3 weeks of storage at 4 °C in 50 mM sodium phosphate buffer, pH 7.0. The supramolecular nature of the immobilization approach was confirmed by cyclic voltammetry.     

Amperometric enzyme biosensor for hydrogen peroxide via Ugi multicomponent reaction

A novel strategy based on the Ugi multicomponent reaction was employed for immobilizing horseradish peroxidase on sodium alginate-coated gold electrode. The electrode was employed for constructing an amperometric biosensor device using 1 mM hydroquinone as electrochemical mediator. The electrode showed linear response (poised at −300 mV vs Ag/AgCl) toward H₂O₂ concentration between 70 μM and 8.8 mM at pH 7.0. The biosensor reached 95% of steady-state current in about 12 s and its sensitivity was 33.8 mA/M cm². The electrode retained full initial activity after 30 days of storage at 4 °C in 50 mM sodium phosphate buffer, pH 7.0.     

Direct electrochemical response of Myoglobin using a room temperature ionic liquid, 1-(2-hydroxyethyl)-3-methyl imidazolium tetrafluoroborate,as supporting electrolyte

Direct electrochemical response of Myoglobin (Myb) at the basal plane graphite (BPG) electrode was observed when a room temperature ionic liquid (RTIL), 1-(2-hydroxyethyl)-3-methyl imidazolium tetrafluoroborate ([HEMIm][BF₄]), was used as the supporting electrolyte. In a 0.17 M [HEMIm]BF₄ aqueous solution, a couple of well-defined redox peaks of Myb could be obtained, whose anodic and cathodic peak potentials were at −0.158 and −0.224 V (vs. Ag/AgCl), respectively. Both anodic and cathodic peak currents increased linearly with the potential scan rate. Compared with the supporting electrolyte of phosphate buffer, [HEMIm][BF₄] played an obvious promotion for the direct electron transfer between Myb and the BPG electrode. Further investigation suggested that Myb was adsorbed tightly on the surface of the BPG electrode in the presence of [HEMIm][BF₄] to form a stable, approximate monolayer Myb film. Myb adsorbed on the BPG electrode surface showed a remarkable electrocatalytic activity for the reduction of oxygen in a [HEMIm][BF₄] aqueous solution. Based on these, a third-generation biosensor could be constructed to directly detect the concentration of oxygen in aqueous solution with a limit of detection of 2.3 × 10⁻⁸ M.     

Gold nanoparticles/tetraaminophenyl porphyrin functionalized multiwalled carbon nanotubes nanocomposites modified glassy carbon electrode for the simultaneous determination of p-acetaminophen and p-aminophenol

A novel electrochemical platform was designed and prepared for simultaneous determination of p-acetaminophen (AMP) and p-aminophenol (AP) by combining the excellent conductivity and electrocatalytic activities of tetraaminophenyl porphyrin functionalized multi-walled carbon nanotubes (CNTs-CONH-TAPP) and gold nanoparticles (AuNPs). The as-synthesized CNTs-CONH-TAPP composites were characterized by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and scanning electron microscope. The incisive oxidation current responses of AMP and AP at the modified electrode promised a sensitive and selective simultaneous determination of AMP and AP. Under optimized conditions, the peak currents were directly proportional to the concentrations of AMP and AP over the ranges of 4.5–500 μmol L⁻¹ and 0.08–60 μmol L⁻¹, respectively, and the limits of detection were 0.44 μmol L⁻¹ for AMP and 0.025 μmol L⁻¹ for AP(S/N = 3) respectively. The proposed modified electrode showed excellent selectivity, reproducibility and long-term stability and could be applied in simultaneous determination of p-acetaminophen and p-aminophenol in real samples.     

3-D nanoporous gold thin film for the simultaneous electrochemical determination of dopamine and ascorbic acid

In this study, we demonstrated a novel fabrication method of three dimensional nanoporous gold thin film (NPGF) onto gold (Au) substrate using electrochemical deposition method. Scanning electron microscope (SEM) investigation reveals the formation of highly-ordered pores, approximately 30 nm in diameter and 150 nm thick. The NPGF-modified electrode shows a linear range (0.1–40 μM) for dopamine detection in the presence of ascorbic acid. The electrochemical measurements of mixtures of dopamine, ascorbic acid, and uric acid in human serum sample for real sample applications was also investigated based on differential pulse voltammetry (DPV) technique. These high sensitivity and selectivity features of the proposed NPGF biosensor offer great promise for real sample biosensor application.     

Application of graphene-modified electrode for selective detection of dopamine

Graphene was synthesized chemically by Hummers and Offeman method and the graphene-modified electrode was applied in selective determination of dopamine with a linear range from 5 μM to 200 μM in a large excess of ascorbic acid. Selective detection was realized in completely eliminating ascorbic acid, different from the methods based on the potential separations. π–π stacking interaction between dopamine and graphene surface may accelerate the electron transfer whereas weaken the ascorbic acid oxidation on this graphene-modified electrode. The resulted graphene-modified electrode also showed a better performance than multi-walled carbon nanotubes-modified electrode. The phenomena were considered from the elusive two-dimensional structure and unique electronic properties of graphene.     

Gold surface patterned with cyclodextrin-based molecular nanopores for electrochemical assay of transglutaminase activity

A novel electrochemical method for measuring transglutaminase activity was reported. This approach was based on the patterning of gold electrodes with a mixed self-assembled monolayer of perthiolated β-cyclodextrin and 1-octanethiol. The proper functionalization of β-cyclodextrin with primary amino groups allowed it to act as amino-donor substrates for transglutaminase and molecular nanopores for the enzyme-controlled diffusion of Fe(CN)₆^{3 −/4 −} to the electrode surface. Voltamperometric measurements allowed detection of transglutaminase in the range of 1.9–37 mU/mL with a sensitivity of 1.42 nA μL U^− 1 s^− 1.     

Novel poly (neutral red) nanowires as a sensitive electrochemical biosensing platform for hydrogen peroxide determination

Poly (neutral red) nanowires (PNRNWs) have been synthesized for the first time by the method of cyclic voltammetric electrodeposition using porous anodic aluminum oxide (AAO) template and were examined by scanning electron microscopy (SEM) and transmission electron microscope (TEM). Moreover, horseradish peroxidase (HRP) was encapsulated in situ in PNRNWs (denoted as PNRNWs–HRP) by electrochemical copolymerization for potential biosensor applications. The PNRNWs showed excellent efficiency of electron transfer between the HRP and the glassy carbon (GC) electrode for the reduction of H₂O₂ and the PNRNWs–HRP modified GC electrode showed to be excellent amperometric sensors for H₂O₂ at −0.1 V with a linear response range of 1 μM to 8 mM with a correlation coefficient of 0.996. The detection limit (S/N = 3) and the response time were determined to be 1 μM and <5 s and the high sensitivity is up to 318 μA mM⁻¹ cm⁻².     

Quasi-reversible two-electron reduction of oxygen at gold electrodes modified with a self-assembled submonolayer of cysteine

The electrochemical reduction of molecular oxygen (O₂) has been performed at gold electrodes modified with a submonolayer of a self-assembly (sub-SAM/Au) of a thiol compound (typically cysteine (CYST)) in O₂-saturated 0.5 M KOH. At bare gold electrode O₂ reduction reaction proceeds irreversibly, while this reaction is totally hindered at gold electrodes with a compact structure of CYST over its surface. The partial reductive desorption of the compact CYST monolayer was achieved by controlling the potential of the CYST/Au electrode, leading to the formation of a submonolayer coverage of the thiol compound over the Au electrode surface (sub-SAM/Au), at which the CYST molecules selectively block the Au(1 0 0) and Au(1 1 0) fractions (the so-called rough domains) of the polycrystalline Au while the Au(1 1 1) component (the so-called smooth domains) remains bare (i.e., uncovered with CYST). This sub-SAM/Au electrode extraordinarily exhibits a quasi-reversible two-electron reduction of molecular oxygen (O₂) in alkaline medium with a peak separation (ΔE_p) between the cathodic and anodic peak potentials (E_p^c,E_p^a) of about 60 mV. The ratio of the anodic current to the cathodic one is close to unity. The formal potential (E^o′) of this reaction is found to equal −150 mV vs. Ag/AgCl/KCl(sat.).     

Non-enzymatic detection of hydrogen peroxide using a functionalized three-dimensional graphene electrode

A novel three-dimensional (3D) electrochemical sensor was developed for highly sensitive detection of hydrogen peroxide (H₂O₂). Monolithic and macroporous graphene foam grown by chemical vapor deposition (CVD) served as the electrode scaffold. Using in-situ polymerized polydopamine as the linker, the 3D electrode was functionalized with thionine molecules which can efficiently mediate the reduction of H₂O₂ at close proximity to the electrode surface. Such stable non-enzymatic sensor is able to detect H₂O₂ with a wide linear range (0.4 to 660 μM), high sensitivity (169.7 μA mM^− 1), low detection limit (80 nM), and fast response (reaching 95% of the steady current within 3 s). Furthermore, this sensor was used for real-time detection of dynamic release of H₂O₂ from live cancer cells in response to a pro-inflammatory stimulant.     

Direct electron transfer of cytochrome c and its biosensor based on gold nanoparticles/room temperature ionic liquid/carbon nanotubes composite film

A robust and effective composite film based on gold nanoparticles (GNPs)/room temperature ionic liquid (RTIL)/multi-wall carbon nanotubes (MWNTs) modified glassy carbon (GC) electrode was prepared by a layer-by-layer self-assembly technique. Cytochrome c (Cyt c) was successfully immobilized on the RTIL-nanohybrid film modified GC electrode by electrostatic adsorption. Direct electrochemistry and electrocatalysis of Cyt c were investigated. The results suggested that Cyt c could be tightly adsorbed on the modified electrode. A pair of well-defined quasi-reversible redox peaks of Cyt c was obtained in 0.10 M, pH 7.0 phosphate buffer solution (PBS). RTIL-nanohybrid film showed an obvious promotion for the direct electron transfer between Cyt c and the underlying electrode. The immobilized Cyt c exhibited an excellent electrocatalytic activity towards the reduction of H₂O₂. The catalysis currents increased linearly to the H₂O₂ concentration in a wide range of 5.0 × 10⁻⁵– 1.15 × 10⁻³ M. Based on the multilayer film, the third-generation biosensor could be constructed for the determination of H₂O₂.     

A label-free electrochemical RNA aptamer for selective detection of theophylline

In this work, we report a novel electrochemical RNA aptamer for the selective detection of theophylline. Firstly, gold nanoparticles were electrodeposited on the surface of glassy carbon (GC) electrode to form a gold nanoparticles modified electrode. Secondly, the designed single-stranded RNA (ssRNA) was immobilized on gold nanoparticles through a thiol linker as a probe RNA. Then, the complement stranded RNA, which can combine with the probe ssRNA to form a double-stranded RNA (dsRNA) with a recognition unit of theophylline, was linked on the probe RNA through a hybrid reaction in the presence of theophylline. Doxorubicin was selected as an electrochemical indicator. The proposed RNA aptamer presents an excellent selectivity for the detection of theophylline. The detectable concentration range of theophylline is from 2.0 to 50.0 μM with a limit of detection of 1.2 μM.