Oxygen reduction reaction activities of Ni/Pt(111) model catalysts fabricated by molecular beam epitaxy

Oxygen reduction reaction (ORR) activities were evaluated for clean Pt(111) and Ni/Pt(111) model catalysts fabricated by molecular beam epitaxy. Exposure of clean Pt(111) to 1.0 L CO at 303 K produced linear-bonded and bridge-bonded CO-Pt IR bands at 2093 and 1858 cm^? 1. In contrast, 0.3-nm-thick Ni deposited on Pt(111) at 573 K (573 K-Ni_0.3 nm/Pt(111)) produced broad IR bands for adsorbed CO at around 2070 cm^? 1; the separation of reflection high-energy electron diffraction (RHEED) streaks is slightly wider for 573 K-Ni_0.3 nm/Pt(111) than for the clean Pt(111). For 823 K-Ni_0.3 nm/Pt(111), the separation of the RHEED streaks is the same as that for the Pt(111), and a single sharp IR band due to adsorbed CO is located at 2082 cm^? 1. The results suggest that for the 823 K-Ni_0.3 nm/Pt(111), a Pt-enriched outermost surface (Pt-skin) was formed through surface segregation of the substrate Pt atoms. ORR activities for the 573 K- and 823 K-Ni_0.3 nm/Pt(111) as determined from linear sweep voltammetry curves were five times and eight times higher than that for clean Pt(111), respectively, demonstrating that Pt-skin generation is crucial for developing highly active electrode catalysts for fuel cells.     

Investigation of the Pt–Ni–Pb/C ternary alloy catalysts for methanol electrooxidation

This research is aimed to increase the activity of anodic catalysts and thus to lower noble metal loading in anodes for methanol electrooxidation. The Pt–Ni–Pb/C catalysts with different molar compositions were prepared. Their performance were tested by using a glassy carbon disk electrode through cyclic voltammetric curves in a solution of 0.5 mol L⁻¹ CH₃OH and 0.5 mol L⁻¹ H₂SO₄. The performances of Pt–Ni–Pb/C catalyst with optimum composition (the molar ratio of Pt/Ni/Pb is 5:4:1) and Pt/C (E-Tek) were also compared. Their particle sizes and structures were determined by means of X-ray diffraction (XRD). The XRD results show, compared with that of Pt/C, the lattice parameter of Pt–Ni–Pb (5:4:1)/C catalyst decreases, its diffraction peaks are shifted slightly to a higher 2θ values. This indicates the formation of an alloy involving the incorporation of Ni and Pb atoms into the fcc structure of Pt. The electrochemical measurement shows the activity of Pt–Ni–Pb/C catalyst with an atomic ratio of 5:4:1 for methanol electrooxidation is the best among all different compositions. The activity of Pt–Ni–Pb (5:4:1)/C catalyst is much higher than that of Pt/C (E-Tek).     

Combinatorial screening of ternary Pt–Ni–Cr catalysts for methanol electro-oxidation

Methanol electro-oxidation activity of ternary Pt–Ni–Cr system was studied by using a combinatorial screening method. A Pt–Ni–Cr thin-film library was prepared by sputtering and quickly characterized by a multichannel multielectrode analyzer. Among the 63 different composition thin-film catalysts, Pt₂₈Ni₃₆Cr₃₆ showed the highest methanol electro-oxidation activity and good stability. This new composition was also studied in its powder form by synthesizing and characterizing Pt₂₈Ni₃₆Cr₃₆/C catalyst. In chronoamperometry testing, the Pt₂₈Ni₃₆Cr₃₆/C catalyst exhibited “decay-free” behavior during 600 s operation by keeping its current density up to 97.1% of its peak current density, while the current densities of Pt/C and Pt₅₀Ru₅₀/C catalysts decreased to 14.0% and 60.3% of their peak current densities, respectively. At 600 s operation, current density of the Pt₂₈Ni₃₆Cr₃₆/C catalyst was 23.8 A g_{noble metal}⁻¹, while that of those of the Pt/C and Pt₅₀Ru₅₀/C catalysts were 2.74 and 18.8 A g_{noble metal}⁻¹, respectively.     

Catalytic oxidation of volatile organic compounds (VOCs). Oxidation of o-xylene over Pd and Pt/HFAU catalysts

The transformation of o-xylene in low concentration (1 700 ppmv) into air was investigated over Pd and Pt/HFAU catalysts (framework Si/Al ratio equal to 17 and 100). Whatever the catalyst, o-xylene oxidation into CO₂ and H₂O is accompanied by the retention within the zeolite pores of heavy compounds (‘coke’). The relative significance of these reactions depends on the operating conditions (temperature, time-on-stream) and on the catalyst characteristics (Pd or Pt, Si/Al ratio). Over Pt and Pd/HFAU(17), time-on-stream has a positive effect on the xylene oxidation apparently related to the reducibility of Pd and Pt species during the reaction. The higher activity of Pt/HFAU catalysts can be attributed to its greater number of active species (especially Pt⁰). Those active species can be more rapidly formed than Pd⁰ by auto reduction during the calcination of Pt precursor. Whatever the metal, the higher the Si/Al ratio of the support, the faster the xylene oxidation and the lower the coke formation. This can be related to the higher proportion of reduced species (Pd⁰ and Pt⁰) formed on the more dealuminated catalyst but also to the hydrophobicity of the support. Indeed, the hydrophobicity of the zeolite play a positive role in the oxidation activity in presence of steam; the higher the Si/Al ratio of the zeolite, the faster the o-xylene oxidation. Thus a catalyst with a low platinum content supported on a hydrophobic zeolite (0.10 Pt/HFAU(100)) allows to oxidising totally o-xylene at 210 °C in presence of steam.     

Iodinated carbon materials for oxygen reduction reaction in proton exchange membrane fuel cell. Scalable synthesis and electrochemical performances

Doped graphene-based cathode catalysts are considered as promising competitors for ORR, but their power density has been low compared to Pt-based cathodes, mainly due to poor mass-transport properties. A new electrocatalyst for PEMFCs, an iodine doped grahene was prepared, characterized, and tested and the results are presented in this paper. We report a hybrid derived electrocatalyst with increased electrochemical active area and enhanced mass-transport properties. The electrochemical performances of several configurations were tested and compared with a typical Pt/C cathode configuration. As a standalone catalyst, the iodine doped graphene gives a performance with 60% lower than if it is placed between gas diffusion layer and catalyst layer. If it is included as microporous layer, the electrochemical performances of the fuel cell are with 15% bigger in terms of power density than the typical fuel cell with the same Pt/C loading, proving the beneficial effect of the iodine doped graphene for the fuel cell in the ohmic and mass transfer region. Moreover, the hybrid cathode manufactured by commercial Pt/C together with the material with best proprieties, is tested in a H₂-Air fuel cell and a power density of 0.55 W cm⁻² at 0.52 V was obtained, which is superior to that of a commercial Pt-based cathode tested under identical conditions (0.46 W cm⁻²).     

Dealloyed carbon-supported PtAg nanostructures: Enhanced electrocatalytic activity for oxygen reduction reaction

Dealloyed PtAg/C nanostructures, prepared by selective electrochemical etching of Ag in 0.5 M H₂SO₄ from a series of alloyed Pt_mAg/C samples with atomic Pt/Ag ratio m = 0.1, 0.5, 1.0 and 1.5, were employed as cathode electrocatalysts for oxygen reduction reaction (ORR) in 0.5 M KOH. Compared with their as-prepared counterpart alloy catalysts, the dealloyed catalysts showed higher half-wave potentials (E_1/2) and significantly higher Pt mass-specific activity (MSA) data. The intrinsic activity (IA) of Pt increased more or less after the dealloying treatment but was strongly dependent on the composition (m) of the alloyed sample. The Pt IA numbers were comparable for the dealloyed catalysts derived from Pt_mAg/C of m = 0.5, 1.0 and 1.5, which were nearly twice that for E-TEK Pt/C catalyst and 3 times that for the dealloyed catalyst derived from Pt_0.1Ag/C.     

Platinum nanoparticles supported on nitrobenzene-functionalised graphene nanosheets as electrocatalysts for oxygen reduction reaction in alkaline media

A systematic study on the electrocatalytic properties of Pt nanoparticles supported on nitrobenzene-modified graphene (Pt-NB/G) as catalyst for oxygen reduction reaction (ORR) in alkaline solution was performed. Graphene nanosheets were spontaneously grafted with nitrophenyl groups using 4-nitrobenzenediazonium salt. The electrocatalytic activity towards the ORR and stability of the prepared catalysts in 0.1 M KOH solution have been studied and compared with that of the commercial Pt/C catalyst. The results obtained show that the NB-modified graphene nanosheets can be good Pt catalyst support with high stability and excellent electrocatalytic properties. The specific activity of Pt-NB/G for O₂ reduction was 0.184 mA cm⁻², which is very close to that obtained for commercial 20 wt% Pt/C catalyst (0.214 mA cm⁻²) at 0.9 V vs. RHE. The Pt-NB/G hybrid material promotes a four-electron reduction of oxygen and can be used as a promising cathode catalyst in alkaline fuel cells.     

Oxygen reduction reaction on the low index planes of palladium electrodes modified with a monolayer of platinum film

Oxygen reduction reaction (ORR) has been studied on the low index planes of Pd modified with a monolayer of Pt (Pt/Pd(hkl)) in 0.1 M HClO₄ with the use of hanging meniscus rotating disk electrode. The activity for ORR on bare Pd(hkl) electrode depends on the surface structure strongly, however, voltammograms of ORR on Pt/Pd(hkl) electrodes do not depend on the crystal orientation. The specific activities of Pt/Pd(hkl) electrodes at 0.90 V (RHE) are higher than that on Pt(1 1 0) which has the highest activity for ORR in the low index planes of Pt. The mass activity on Pt/Pd(hkl) electrode is 7 times as high as a commercial Pt/C catalyst.     

NiSe2 nanoparticles embedded in CNT networks: Scalable synthesis and superior electrocatalytic activity for the hydrogen evolution reaction

For the first time, NiSe₂ nanoparticles embedded in CNT networks have been synthesized via spray-drying followed by a selenization process. The NiSe₂/CNTs hybrid (NCH) delivers superior electrocatalytic performance for HER. It has a low onset potential of ~ 159 mV and a cathode current density of 35.6 mA cm^− 2 at − 250 mV vs RHE; more importantly, the Tafel slope has a very low value of 29 mV dec^− 1, which is comparable to a platinum (Pt) catalyst; in addition, it is stable even after 1000 cycles. The superior HER performance of NCH is attributed to its unique structure, which is composed of ultrathin NiSe₂ nanoparticles homogenously embedded in highly conductive and porous CNT networks. This not only provides abundant HER active sites, but also guarantees robust contact between the NiSe₂ nanoparticles and the CNT networks. The present study provides new insights into the large-scale and low-cost synthesis of a highly effective and stable NiSe₂-based electrocatalyst which could be extended to large-scale production of other non-precious metal hybrid catalysts with low cost, high efficiency and excellent stability.     

Hydrogen oxidation reaction on thin platinum electrodes in the polymer electrolyte fuel cell

A method for measuring the kinetics of the hydrogen oxidation reaction (HOR) in a fuel cell under enhanced mass transport conditions is presented. The measured limiting current density was roughly 1600 mA cm_Pt^? 2, corresponding to a rate constant of the forward reaction in the Tafel step of 0.14 mol m^? 2 s^? 1 at 80 °C and 90% RH. The exchange current density for the HOR was determined using the slope at low overvoltages and was found to be 770 mA cm_Pt^? 2. The high values for the limiting and exchange current densities suggest that the Pt loading in the anode catalyst can be reduced further without imposing measurable voltage loss.     

Efficient stripping voltammetric detection of organophosphate pesticides using NanoPt intercalated Ni/Al layered double hydroxides as solid-phase extraction

We developed a simple strategy for designing a sensitive electrochemical stripping voltammetric sensor for organophosphate pesticides (OPs) based on solid-phase extraction (SPE) using nanosized Pt intercalated Ni/Al layered double hydroxides (labeled as NanoPt-LDHs). By assembling NanoPt with LDHs together, the resulting NanoPt-LDHs are highly efficient to capture OPs. It dramatically facilitates the enrichment of OPs onto their surface and realizes the sensitive stripping voltammetric detection of methyl parathion (MP) as a model of OPs. The stripping analysis shows highly linear over MP concentration ranges of 0.001–0.15 and 0.3–1.0 μg mL^? 1 with a detection limit of 0.6 ng mL^–1 (S/N = 3). The combination of NanoPt, LDHs, SPE, and square-wave voltammetry (SWV) provides a fast, simple, and sensitive electrochemical method for OPs.     

Unique CO-tolerance of Pt–WOx materials

Well-defined tungsten-oxide-supported platinum nanoparticles (Pt/WO_x) were elaborated by impregnation-reduction of a platinum salt onto commercial monoclinic WO₃. Field-emission gun scanning electron microscopy (FEG-SEM) and transmission electron microscopy (TEM) revealed that the Pt particles are well-distributed on the oxide support, present a narrow particle size distribution centered on ca. 2–3 nm and a low degree of agglomeration. Carbon black was added to ensure electronic percolation in the electrodes during the electrochemical measurements. CO_ads electrooxidation currents were monitored at potentials as low as 0.1 V vs. RHE on Pt/WO_x, demonstrating high CO-tolerance compared to carbon-supported Pt or PtRu catalysts.     

Highly active PtRuFe/C catalyst for methanol electro-oxidation

High methanol electro-oxidation activity was obtained on novel PtRuFe/C (2:1:1 at.%) catalyst. Mass and specific activities were 5.67 A  g⁻¹ catal. and 177 mA m⁻² for the PtRuFe/C catalyst while those of the commercial PtRu/C catalyst were 2.28 A g⁻¹ catal. and 87.7 mA m⁻², respectively. CO stripping results showed that on-set voltage for CO electro-oxidation was lowered by incorporation of Fe. XRD and XPS results revealed that Fe₂O₃ was formed instead of Fe(0), which resulted in large electron deficiency in Pt and easy CO electro-oxidation. The electron deficiency of Pt was proved by XPS results of Pt4f peaks, which moved to higher binding energies in PtRuFe/C than PtRu/C.     

Amperometric biosensors based on deposition of gold and platinum nanoparticles on polyvinylferrocene modified electrode for xanthine detection

In this study, new xanthine biosensors, XO/Au/PVF/Pt and XO/Pt/PVF/Pt, based on electroless deposition of gold(Au) and platinum(Pt) nanoparticles on polyvinylferrocene(PVF) coated Pt electrode for detection of xanthine were presented. The amperometric responses of the enzyme electrodes were measured at the constant potential, which was due to the electrooxidation of enzymatically produced H₂O₂. Compared with XO/PVF/Pt electrode, XO/Au/PVF/Pt and XO/Pt/PVF/Pt exhibited excellent electrocatalytic activity towards the oxidation of the analyte. Effect of Au and Pt nanoparticles was investigated by monitoring the response currents at the different deposition times and the different concentrations of KAuCl₄ and PtBr₂. Under the optimal conditions, the calibration curves of XO/Au/PVF/Pt and XO/Pt/PVF/Pt were obtained over the range of 2.5 × 10^?3 to 0.56 mM and 2.0 × 10^?3 to 0.66 mM, respectively. The detection limits were 7.5 × 10^?4 mM for XO/Au/PVF/Pt and 6.0 × 10^?4 mM for XO/Pt/PVF/Pt. The effects of interferents, the operational and the storage stabilities of the biosensors and the applicabilities of the proposed biosensors to the drug samples analysis were also evaluated.     

Intrinsically microporous polymer slows down fuel cell catalyst corrosion

The limited stability of fuel cell cathode catalysts causes a significant loss of operational cell voltage with commercial Pt-based catalysts, which hinders the wider commercialization of fuel cell technologies. We demonstrate beneficial effects of a highly rigid and porous polymer of intrinsic microporosity (PIM-EA-TB with BET surface area 1027 m² g^− 1) in accelerated catalyst corrosion experiments. Porous films of PIM-EA-TB offer an effective protective matrix for the prevention of Pt/C catalyst corrosion without impeding flux of reagents. The results of electrochemical cycling tests show that the PIM-EA-TB protected Pt/C (denoted here as PIM@Pt/C) exhibit a significantly enhanced durability as compared to a conventional Pt/C catalyst.     

Comparative theoretical study of the structure and bonding of propyne on the Pt(1 1 1) and Pd(1 1 1) surfaces

The interaction of propyne with the Pt(1 1 1) and Pd(1 1 1) surfaces has been studied by means of the generalised gradient approach of density functional theory using periodic slab models. For both surfaces, the most stable adsorption mode of propyne is di-σ/π mode where the hydrocarbon is σ-bonded to two metal atoms with some additional π bonding to a third adjacent surface atom. The adsorption geometry is a highly distorted propyne with the C₁ and C₂ in a nearly sp² hybridisation. Two equivalent surface structures have been found on Pt and Pd. These correspond to the adsorption on the fcc or hcp hollow sites. The adsorption energies on Pt(1 1 1) and Pd(1 1 1) are predicted to be ∼−197 and −161 kJ mol⁻¹, respectively. The electronic factors that control the chemisorption have been analysed by means of the projected density of states.     

Electron-deficient adduct site in the ring opening of methylcyclopentane (MCP) on tungsten-oxide-supported Pt,Ir and Pt–Ir catalysts

The activities of Pt/WO₂, Ir/WO₂ and Pt–Ir/WO₂ toward the conversion of methylcyclopentane (MCP) were investigated. The catalysts were prepared using impregnation and co-impregnation methods and were characterized by SEM, XRD, N₂-sorption and TEM investigations. The most active catalyst toward the conversion of MCP, irrespective of the temperature, was Ir/WO₂. The order of the reactivity was Ir/WO₂ > Pt–Ir/WO₂ > Pt/WO₂. Strong metal–support interactions (SMSI) were observed for all the catalysts over the entire investigated temperature range. At 400 °C, the Pt and Pt–Ir showed 100% selectivity toward ring-enlargement reactions associated with the presence of electron-deficient adduct sites on the reducible acidic WO₂ support. Ring opening occurred over all the catalysts in three positions, resulting in the formation of 2-methylpentane (2-MP), 3-methylpentane (3-MP), and n-hexane (n-H). Difficulty in breaking the secondary – tertiary carbon bonds was observed predominantly on the Ir catalyst, which opens the MCP ring via a selective mechanism.     

Double cyclometallation of bridging 3,6-bis(2-thienyl)-1,2,4,5-tetrazine in a dinuclear mesityl(dimethylsulfoxide)platinum(II) complex: Structure and properties

3,6-Bis(2-thienyl)-1,2,4,5-tetrazine (bttz) reacts with trans-Pt(dmso)₂(mes)₂, mes = mesityl = 2,4,6-trimethylphenyl, under twofold cyclometallation to yield structurally characterized (μ-bttz-2H⁺)[Pt(dmso)(mes)]₂ with uncoordinated thiophene sulfur atoms and bttz deprotonated in the 3,3′ positions. The structural features include cis-positioned carbanionic ligands, twisted mesityl substituents, S-coordinated dmso ligands with the SO bonds lying in the molecular plane, shortened inter-ring bonds, and rather short Pt–C bonds at 1.998(9)/2.00(1) Å (Pt–C_mes) and 1.985(9)/1.99(1) Å (Pt–C_bttz-2H+). Reversible reduction to {(μ-bttz-2H⁺)[Pt(dmso)(mes)]₂}^? causes a high-energy shift of the charge transfer bands and the appearance of an unresolved EPR signal at g = 1.9905.     

Ultra-low platinum loading high-performance PEMFCs using buckypaper-supported electrodes

The microstructure of the catalyst layer in proton exchange membrane fuel cells (PEMFCs) greatly influences catalyst (Pt) utilization and cell performance. We demonstrated a functionally graded catalyst layer based on a double-layered carbon nanotube/nanofiber film- (buckypaper) supported Pt composite catalyst to approach an idealized microstructure. The gradient distribution of Pt, electrolyte and porosity along the thickness effectively depresses the transport resistance of proton and gas. A rated power of 0.88 W/cm² at 0.65 V was achieved at 80 °C with a low Pt loading of 0.11 mg/cm² resulting in a relatively high Pt utilization of 0.18g_Pt/kW. The accelerated degradation test of catalyst support showed a good durability of buckypaper support because of the high graphitization degree of carbon nanofibers.     

Easily prepared,high activity Ir–Ni oxide catalysts for water oxidation

Ir–Ni oxide nanoparticles were simply prepared by stirring IrCl₃ and NiCl₂ precursors in aqueous base under air. The activities of a series of IrNi_yO_x nanoparticles with different Ir-to-Ni ratios were measured toward water oxidation in 0.1 M H₂SO₄. The Ir-to-Ni ratio was 1:0.125 in the most active catalyst (mass normalized > 140 A g^− 1 Ir, electrochemically active surface area normalized > 203 A mmol^− 1Ir). The stabilized potential for the galvanostatic oxidation (1 mA cm^− 2_geometric) was as low as 1.51 V_RHE, corresponding to 0.28 V in overpotential.