非晶态羧酸盐法合成NTC热敏陶瓷用Ni1.0Co0.2Mn1.8O4纳米粉体的研究

Nano-crystalline Ni_1.0Co_0.2Mn_1.8O₄ powders were synthesized via non-crystalloid precursor method. The results on the precursor by XRD and IR techniques show that the stable non-crystalloid precursor could be formed by adding oleic acide and adjusting the pH values. The dried precursor exhibited auto-catalytic combustion behavior. After being calcined at 800 ℃, the Ni_1.0Co_0.2Mn_1.8O₄ powders with spinel structure were obtained. It has been demonstrated that the synthesized powder is well dispersed and with higher sintering activity. The Model of non-crystalloid precursor has been suggested. The reaction mechanism has also been proposed.     

纳米二氧化钛粉末的溶胶-凝胶法合成及晶相转化

Nanosized TiO₂ powder with anatase and rutile structures was synthesized by a sol-gel method using TiCl₄ ethanol solution as a precursor.The grain size of TiO₂ powder was about 63nm after the precursor was calcined at 600℃ for 2 hours .The experimental techniques of XRD,TEM and Particle Distribution were used to characterize the synthesized specimens. Various special effects were investigated for their contribution to crystal structure and the size of TiO₂ powder .The formation of anatase as well as the rutile phase of TiO₂ was indicted from the XRD when the reaction temperature was above 30℃ and when the sol was irradiated by infrared rays .However, an anatase TiO₂ powder formed after the heat treatment of the dried gel in a temperature range from 300℃ to 500℃.Under the vacuum drying and with the calcined time below 3hours ,the anatase phase was gained .As well as with the increase of gelatinizing time, the anatase TiO₂ powder was obtained.     

锂离子电池正极材料LiMn2O4的合成与晶体结构（英）

Spinel LiMn₂O₄ powders were prepared using two-step synthesis method consisting of solid-state reaction method and citrate modified sol-gel method. The effects of the calcination temperature and the Li/Mn ratio of raw materials were studied on the physicochemical and electrochemical properties of the spinel LiMn₂O₄ powders, such as crystallinity, lattice constant and density. The title compound was characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Polycrystalline LiMn₂O₄ powers calcined at 750 ℃ were found to be composed of very uniformly-sized microcrystal with an average particle size of 300 nm. The improvement in electrochemical properties was mainly attributed to the process of re-grinding by absolute alcohol.     

纳米BaFe12O19永磁铁氧体的制备、结构和磁性的研究

In this paper, the nanometer permanent magnetic BaFe₁₂O₁₉ powder was synthesized by a novel method of independent nucleation and crystallization steps and subsequent heat treatment,during the synthesis, Ba(NO₃)₂, Fe(NO₃)₂ and NH₄HCO₃·NH₂COONH₄ were used as starting materials. The effect of crystallization process and heat treatment conditions on the particle size, microstructure and magnetic properties of powder was studied by using XRD, TEM and vibration sample magnetometometer techniques.XRD results showed that the hematite, α-Fe₂O₃, was the main phase in the powder at heat treatment temperatures below 650℃ and its amount in the powder was decreased with increasing temperature and small amount of α-Fe₂O₃ was still remained after being heated at 900℃ for 8hrs. BaFe₁₂O₁₉ was formed about 650℃ and its amount increased in the powder as temperature raised and the higher temperature was needed to attain considerable amount of BaFe₁₂O₁₉ and ideal nanometer BaFe₁₂O₁₉ particle in the powder. The temperature between 40℃～60℃ in the crystallization process was favor to the formation of good BaFe₁₂O₁₉ crystal and to the good magnetic properties of the powder. TEM showed that the particle size in the powder increased with the enhancement of the temperature and the powder crystallized at 40℃ and heated at 800℃ for 8hrs afterwards had a very homogenous particle size distribution, and that the powder heated at 900℃ for 8hrs with the same crystalline condition as the former had a typical hexagonal shape and a chain aggregation. Specific saturation and residential magnetizations and coercive force of the powder increased mono-tonically with the increase of temperature, and reached 39.86A·m²·kg^-1, 23.96A·m²·kg^-1, 480kA·mg^-1 at 900℃, respectively.     

碱土金属掺杂纳米TiO2催化剂的制备与光催化活性的评价

The nanometer TiO₂ were prepared by the hydrolyze-gel method and fellowed by doping alkaline-earth metals (Mg, Ca, Sr, Ba). XRD, SEM, diffuse reflection spectra were used to investigate their characteristices. The result indicates that the average particles size of the TiO₂ is about 80 nm and keep uniformity in distributing. The product was mainly anatase in 300～400 ℃ calcinations, the einstein shift of absorption spectrum was observed after doping the alkaline-earth metals. The best mole percentages of Mg, Ca, Sr and Ba are 0.5%, 1.0%, 1.5%, 1.5% respectively. Under the same reaction conditions, it is more effective to the UV-catalyed degradation reaction that the catalysts containing Mg and Ca were calcined at 300 ℃ for 1h or containing Sr and Ba were calcined at 400 ℃ for 1 h. The photocatalystic activity is considerably depondent on pH and the concentration of the oxidant. Using the sunlight to do the degradation experimental, the result also show that the doping catalysts has higher degradation efficiency than that of pure TiO₂.     

新型阴极材料Ba0.5Sr0.5Co0.8Fe0.2O3-σ制备与性能研究

Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-σ(BSCF), a new cathode material for solid oxide fuel cell (SOFC), was synthesized by polyacrylicacid (PAA) method. The lattice structures of samples calcined at different temperatures were characte-rized by XRD. Shrinkage, porosity and pore size of the porous BSCF as a function of sintering temperature were investigated. It was found that the cubic perovskite structure could be formed after calcination at 800 ℃ for 2 h, but not well crystallized as seen from some unknown phases, and the pure cubic perovskite structure was formed after calcination at 1 150 ℃ for 2 h. The particle size of BSCF was less than 1～2 μm. The shrinkage of the porous BSCF increased with sintering temperature, but the opposite was true for the porosity. After sintering at 1 100 ℃ for 4 h, the porous BSCF was still in an appropriate structure, with porosity of 29% and electrical conductivity above 400 S·cm^-1.     

草酸盐共沉淀法制备Y1.84La0.16O3纳米粉体

Nanopowder of Y_1.84La_0.16O₃ was prepared by oxalate co-precipitation method. The powder was characterized by TG-DTA, XRD and TEM. The results show that the precursor is Re₂(NO₃)₂(C₂O₄)₂·2H₂O (Re=Y, La), and the Y_1.84La_0.16O₃ nanopowders produced by calcining the precursor at 1 000 ℃ for 4 h are 20～40 nm spherical particles and well dispersed. The powders were with high sintering activity and could be fabricated to transparent ceramic without additive at 1 450～1 550 ℃ in H₂ atmosphere for 3 hours. The total transmission of the transparent ceramic could reach 80%.     

单分散超细ZnO粉体的制备与表征

Monodispersed superfine ZnO powders with particle size of about 200～400nm were successfully prepared by the decompressed distillation process with n-butyl alcohol as the solvent. The starting materials were Zn(NO₃)2·6H₂O and NH₃·H₂O. TG-DSC， XRD， TEM and BET surface areas techniques were used to characterize the precursor and as-prepared superfine ZnO powders. In the preparation process of superfine ZnO powders， two techniques including the decompressed distillation with n-butyl alcohol and washing with absolute ethanol were used to avoid agglomeration. It is showed that the decompressed distillation process has a better effect in avoiding ag-glomeration than washing with absolute ethanol. The precursor obtained by the decompressed distillation technique has a lower calcination temperature than the one obtained by washing with absolute ethanol. Zincite phase of ZnO with some impurities was obtained when the precursor was calcined at 200℃ for 2h. After it was calcined at 300℃ for 2h， pure superfine ZnO powder was obtained.     

纳米Co3O4的制备、 表征及CO低温催化氧化

Various nanometer Co₃O₄ samples were prepared and the catalytic performance of CO oxidation were examined. It was found that the activities of the catalysts were greatly changed with variation of the preparation methods and pretreatment conditions. Among the samples tested, Co₃O₄ prepared by using dodecylbenzene sulfonic acid sodium salt(DBS) as the surfactant, calcined at 300 ℃ showed the highest activity and it was able to oxidize completely CO even at -78 ℃. Characterization of these samples by XRD and BET means showed that the catalytic acitivity increased with the decrease of the average particle size, suggests that the average particle size of nanometer Co₃O₄ samples is the main controlling factor of the catalytic activity.     

Li4Ti5O12溶胶-凝胶法合成及其机理研究

The precursors of Li₄Ti₅O₁₂ were prepared from tetrabutyl titanate and lithium acetate by sol-gel process. The Li₄Ti₅O₁₂ samples were synthesized by calcining the gel precursors at 400～900 ℃ in air for 6～20 h. Its reaction mechanism was investigated by infrared spectroscopy(IR), thermogravimetry(TG) and X-ray diffraction(XRD). The effects of sinter-temperature, calcination-time and thermal-treatment for the products were discussed. The samples were characterized by X-ray diffraction(XRD), scanning electron microscopy(SEM). The results showed that the single-phase products were obtained by calcining the gel precursors at 800 ℃ in air for 20 h, the sinter-temperature was lower than that of solid-state method, the particles were narrowly distributed, well crystallized with a size range from 0.3μm to 0.5 μm.     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Phase relations in the K2W2O7-K2WO4-KPO3-Bi2O3 system and structure of K6.5Bi2.5W4P6O34

The phase relations in the cross-section of the K₂W₂O₇-K₂WO₄-KPO₃ containing 15 mol% Bi₂O₃ were undertaken using flux method. Crystallization fields of K_6.5Bi_2.5W₄P₆O₃₄, K₂Bi(PO₄)(WO₄), Bi₂WO₆, KBi(WO₄)₂ and their cocrystallization areas were identified. Novel phase K_6.5Bi_2.5W₄P₆O₃₄ was characterized by single-crystal X-ray diffraction: sp. gr. P−1, a=9.4170(5), b=9.7166(4), c=17.6050(7) Å, α=90.052(5)°, β=103.880(5)° and γ=90.125(5)°. It has a layered structure, which contains {K₇Bi₅W₈P₁₂O₆₈}_∞ layers stacked parallel to ab plane and sheets composed by potassium atoms separating these layers. Sandwich-like {K₇Bi₅W₈P₁₂O₆₈}_∞ layers are assembled from [W₂P₂O₁₃]_∞ and [BiPO₄]_∞ building units, and are penetrated by tunnels with K/Bi atoms inside. FTIR-spectra of K₂Bi(PO₄)(WO₄) and K_6.5Bi_2.5W₄P₆O₃₄ were discussed on the basis of factor group theory.     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Solubility in the Na2Cr2O7-(NH4)2Cr2O7-K2Cr2O7-H2O system

Solubility in the Na₂Cr₂O₇-(NH₄)₂Cr₂O₇-K₂Cr₂O₇-H₂O four-component water-salt system at 25, 50, and 75°C was studied for the first time. Phase field boundaries for individual salts and potassium and ammonium dichromate solid solutions, monovariant lines, and invariant points were determined. Experimental data were used to optimize the looped isohydric process of potassium dichromate preparation involving additional salts.     

NaBO2-NaCl-Na2CO3, NaBO2- Na2CO3-NaMoO4, NaBO2- Na2CO3-NaWO4, and NaBO2-NaCl-Na2WO4 ternary systems

The phase diagrams of the NaBO₂-NaCl-Na₂CO₃, NaBO₂-Na₂CO₃-Na₂MoO₄, NaBO₂- Na₂CO₃-Na₂WO₄, and NaBO₂-NaCl-Na₂WO₄ ternary systems were studied by a calculation-experimental method and differential thermal analysis. The coordinates of ternary eutectics were determined: E ₁: 612°C, 16 mol % NaBO₂, 42 mol % NaCl, and 42 mol % Na₂CO₃; E ₂: 568°C, 12 mol % NaBO₂, 28 mol % Na₂CO₃, and 60 mol % Na₂MoO₄; E ₃: 575°C, 12 mol % NaBO₂, 32 mol % Na₂CO₃, and 56 mol % Na₂WO₄; E ₄: 628°C, 8 mol % NaBO₂, 20 mol % NaCl, and 72 mol % Na₂WO₄; and E ₅: 655°C, 9 mol % NaBO₂, 53 mol % NaCl, and 38 mol % Na₂WO₄.     

Li2SO4-Na2SO4-H2O和Li2SO4- K2SO4-H2O溶液的体积性质

本文用高精度数字式振荡管密度计测定了288K至318K温度范围内Li₂SO₄ + Na₂SO₄ + H₂O和 Li₂SO₄ + K₂SO₄ + H₂O三元体系的密度。混合溶液的离子强度范围从0.1到4.5 mol.kg_–1,混合溶液中Na₂SO₄和K₂SO₄的离子强度分数为0.2,0.4,0.6和0.8。用密度实验值拟合得到了不同温度下Pitzer离子相互作用模型混合参数θ_V和 ψ_V,模型的计算值与实验值的偏差在±0.002 g.cm_–3以内。用Pitzer模型计算了不同离子强度下三元体系的混合体积。     

Extension of the La7Mo7O30 structural type with La7Nb3W4O30 and La7Ta3W4O30 compounds

Two compounds of formula La₇A₃W₄O₃₀ (with A=Nb and Ta) were prepared by solid-state reaction at 1450 and 1490 °C. They crystallize in the rhombohedric space group R-3 (No. 148), with the hexagonal parameters: , and , . The structure of the materials was analyzed from X-ray, neutron and electronic diffraction. These oxides are isostructural of the reduced molybdenum compound La₇Mo₇O₃₀, which are formed of perovskite rod along [111]. An order between (Nb, Ta) and W is observed.     

SnSbBiS4-SnS and SnSbBiS4-Sn2Sb6S11 sections of the SnS-Sb2S3-Bi2S3 ternary system

SnSbBiS₄-SnS and SnSbBiS₄-Sn₂Sb₆S₁₁ sections were studied by physicochemical methods (DTA, X-ray powder diffraction, microstructure observation, and microhardness measurements). These sections were found to be eutectic quasi-binary sections of the SnS-Sb₂S₃-Bi₂S₃ ternary system. Solid solution regions based on the initial components were found on either side of the sections. Alloys in the solid solution region are p-type semiconductors.     

Theoretical study of polyoxide clusters B20O30, Al20O30, V20O50, Si20O30H20, and Si20O30F20

The structural, electronic, and vibrational characteristics and energies of the isolated polyoxide clusters B₂₀O₃₀, Al₂₀O₃₀, V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀ and their complexes with the H⁻ ion and ammonia complexes Al₂₀O₃₀ · nNH₃ have been calculated by the density functional theory B3LYP method with different basis sets. The computation results show that the symmetric closo structure I _h with oxygen bridges located above the centers of the faces of an empty [M₂₀] dodecahedron is more favorable for V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀. For B₂₀O₃₀, the cage closo isomer is also more favorable than the other isomers, but its structure is severely distorted as compared to a dodecahedron and has a symmetry close to C ₃ . For Al₂₀O₃₀, the I _h structure corresponds to a high-lying local minimum of the potential energy surface. For Al₂₀O₃₀, a set of unusual puckshaped isomers of symmetry C _i , with different numbers of four-coordinate atoms ^IVAl and three-coordinate atoms ^IIIO, was localized; these structures are more than 90 kcal/mol more favorable than the dodecahedron I _h . The most favorable isomer of Al₂₀O₃₀ contains twelve four-coordinate atoms ^IVAl and four five-coordinate atoms ^VAl. The energies of dissociation of the most favorable M₂₀O₃₀ clusters into the M₂O₃ (C _2v ) and M₄O₆ (T _d ) fragments and, in the case of Al₂₀O₃₀, also into the Al₈O₁₂ (O _h ) and Al₁₂O₁₈ (D _3d ) fragments, have been estimated. The conclusion has been drawn that these clusters can, in principle, exist and can be experimentally detected in the isolated state. Analogous calculations have been performed for ammonia complexes Al₂₀O₃₀ · nNH₃ with n varying from 1 to 20. The effect of solvation on the relative stability of the dodecahedral and puckshaped isomers of the Al₂₀O₃₀ cluster is observed. The isomers with ammonia molecules in their first coordination sphere become much closer to one another on the energy scale; however, the dodecahedron remains a considerably less favorable intermediate. Original Russian Text ? O.P. Charkin, N.M. Klimenko, D.O. Charkin, 2008, published in Zhurnal Neorganicheskoi Khimii, 2008, Vol. 53, No. 4, pp. 624–635.     

Structural chemistry of Sr3Cr2WO9, Ca3Cr2WO9, and Ba3Cr2WO9

We have studied the preparation and crystallographic structure of three perovskite-type compounds: Sr₃Cr₂WO₉, cubic, the lattice parameter of which is a = 7.812Å; Ca₃Cr₂WO₉, tetragonal, the lattice parameters of which are a = 5.408 Å and c = 7.635Å; and Ba₃Cr₂WO₉, hexagonal, the lattice parameters of which are a = 5.691 Å and c = 13.957Å. We have compared these three structures and shown the relationship between the dimensions of the alkaline-earth metal and the existence of the different structures.