有机物气相色谱法中光离子化灵敏度的定量结构与性质相关性研究

把Ａｍ拓扑指数与分子连接性指数用于有机化合物气相色谱分析的光离子化灵敏度的结构－性质相关性研究中,并将遗传算法（ＧＡ）引用于本研究中建模,与相应体系的光离子化灵敏度进行相关分析时发现,Ａm指数,分子连接性指数均能较好地反映化合物的结构特征,但各有特点,ＧＡ算法所得结果优于多元回归分析。     

顶空–GC测定卷烟包装材料用胶粘剂中挥发性有机化合物时所用溶剂的研究

1,3-二甲基-2-咪唑烷酮(DMI)是一种高沸点、同水互溶、同各种挥发性有机化合物互溶的有机溶剂,各种卷烟包装材料用胶粘剂能在DMI中良好地分散溶解,因此DMI适合作为顶空–气相色谱法测定卷烟包装材料所用胶粘剂中19种挥发性有机化合物含量时所用溶剂。为了降低实验成本、降低实验方法检出限,可在DMI中加入一定比例的水,将含量在0.8 mg/mL左右的19种挥发性有机化合物的标准溶液用DMI及不同比例的水稀释后,进行气相色谱液体进样和顶空进样实验。结果表明,样品稀释后含有30%(体积分数)的水时,各化合物含量比较稳定,可降低大多数挥发性有机化化合物的检出限。     

Membrane Extraction Combined with Thermodesorption/Gas Chromatography and Mass Selective Detection for the Analysis of Volatile Organic Compounds in Water

The range of application of a commercial thermodesorption-cryofocussing unit connected to a gas chromatograph/mass selective detector was extended to water analysis by using it in conjunction with membrane extraction. A flow of nitrogen passes through a silicone hollow fiber immersed in the water sample and extracted volatile organic compounds are enriched in a sorption tube mounted on top of the extraction cell. The sorption tube is then placed in the thermodesorption unit and analyzed by GC/MS. The optimal extraction parameters of this combined method were found to be 30 min extraction at 20°C with a stirring speed of 1,250 rpm and a flow rate of 100 mL/min nitrogen using a silicone hollow fiber of 0.3 m length. Under these conditions the reproducibility of the method was 5.2–10.5% RSD. The linear dynamic range of the optimized method spans three orders of magnitude and detection limits were found to be 0.02–0.1 μg/L for cis/trans-1,2-dichloroethene, benzene, trichloroethene, chlorobenzene, bromobenzene, ethylbenzene, 1,1,2,2-tetrachloroethane, and 1,2/1,4-dichlorobenzene. The method was found to be suitable for compounds with boiling points up to 220°C as memory effects increased considerably from dichloro- to hexachlorobenzene. Highly contaminated groundwater samples were analyzed. Quantitative results corresponded well with those achieved with conventional headspace-GC/FID.     

顶空-固相微萃取-气相色谱法检测可可麦汁中吡嗪类化合物

建立了顶空-固相微萃取(HS-SPME)-气相色谱快速测定可可麦汁中3种吡嗪类物质(2,5-二甲基吡嗪、2,3,5-三甲基吡嗪和2,3,5,6-四甲基吡嗪)的方法.选择不同的固相微萃取头对萃取温度和时间进行优化,所得最佳萃取条件为:在60℃下,采用75 μm CAR/PDMS萃取头对麦汁样品萃取40 min.本方法的检出限(S/N=3)为0.023～ 0.056 μg/L,线性范围1～500 mg/L;相对标准偏差为3.6％～6.4％;回收率为95.4％～102.7％.本方法应用于样品检测,发现可可麦汁中吡嗪的浓度与原料中可可粉的添加量正相关,显示了很好灵敏性.     

大气降尘中有机物的提取分离及其气相色谱-质谱分析

采用索氏萃取法提取大气降尘中的有机物,用自制的硅胶层析柱进行了分离纯化,并以气相色谱/质谱法对提取物进行了分析.结果表明:从临沂师范学院前十学生公寓和临沂市汽车总站采集到的大气降尘样品中都含有较多的烷类、醛酮类、苯类和酯类有机化合物,并检测到一定量的卤代烃、酞酸酯类、多环芳烃类等有害于健康的物质.经初步推测,大气降尘中的有机化合物与机动车尾气排放有很大关系.文中对大气降尘中有机化合物的分析将为进一步研究大气降尘中有害物质的来源、迁移及其转化规律提供参考.     

用毛细管气相色谱脉冲火焰光度检测器测定汽油中的含硫化合物

采用毛细管气相色谱／脉冲火焰光度检测器（GC／PFPD）对催化裂化汽油中大部分硫化物做了定量和定性研究。在此基础上,考察了降硫助剂与平衡剂掺混后的使用性能,并采用GC／PFPI）对产物FCC汽油中硫化合物进行了分析测定,结果表明降硫助剂的加入使FCC汽油硫含量显著下降。     

乙腈-无机盐-水双水相体系萃取-气相色谱法检测鱼肉中拟除虫菊酯

以乙腈-无机盐-水双水相体系,建立了一种环保、高效的用于气相色谱法检测鱼肉样品中拟除虫菊酯的样品前处理方法.实验利用荧光猝灭法与气相色谱法研究了拟除虫菊酯药物在以蛋白质为主要基质的水产品中的存在状态,考察了双水相的形成条件,并探讨了蛋白质对双水相萃取率的影响.结果表明,拟除虫菊酯药物通过疏水作用力与蛋白质牢固结合.以体积分数为80%的乙腈水溶液作为萃取液可以引起水产品中的蛋白质基质缓慢而彻底地变性,从而充分释放与蛋白质结合的药物,实现拟除虫菊酯的均相高效萃取.80%的乙腈水溶液具有较强的化学极性,因而在双水相系统上相中与药物残留共同萃入的脂溶性杂质较少,萃取液净化步骤大大简化.在双水相上相中加入无水MgSO4,PSA去除水分与杂质后,直接进样进行气相色谱检测.该方法用于鱼肉样品中六种拟除虫菊酯的萃取检测,回收率为81.1%～96.4%,检出限为8～14ng·mL-1.     

Trace Determination of Organic Compounds in Water by Direct Enrichment in Multichannel Thick Film Silicone Rubber Traps with Capillary Gas Chromatography

The application of Multichannel Silicone Rubber Traps for the direct analysis of organic compounds in water was studied. The optimum collection flow rate for a 10 mL sample was found to be ca. 150 μL·min^–1. The effect of methanol on the retention power of the trap was evaluated. The addition of a methanol fraction of up to 40% to the water standards did not show any loss in collection efficiency. It was shown that the extraction of organic compounds from water with the multichannel trap is uncomplicated, i. e. methanol is not required to achieve accurate analyses, concentration of the sample onto the trap is by gravity flow, and excess water remaining in the multichannel trap after water extraction is removed by centrifugation. With the use of the multichannel silicone rubber trap a wide boiling point range of compounds were analyzed from aqueous samples at levels of 1–4 μg·L^–1.     

A Novel Biomass Supported Na2CO3 System for Flue Gas Desulfurization

The breakthrough and stoichiometric SO2 adsorption efficiencies of a biomass supported Na2CO3 system (80 wt %Na2CO3/straw) have reached 48.9% and 80.6% respectively at a desulfurization temperature of 80℃.     

Combination of a Mid-infrared Hollow Waveguide Gas Sensor with a Supported Capillary Membrane Sampler for the Detection of Organic Compounds in Water

A Fourier transform infrared (FT-IR) spectroscopy based gas sensor for continuous analysis of liquid phase samples has been developed, coupling a short hollow waveguide (HWG) gas cell with a supported capillary membrane sampler (SCMS) probe. Passing an inert carrier gas through the thin-walled tubular silicon membrane enables the permeation of volatile organic compounds (VOCs) present in aqueous solution and facilitates their continuous and quantitative detection in the infrared hollow fiber by multiple internal reflection spectroscopy. The sensitivity of the sensor system has been determined at the ppb (μg/L) concentration level and the response time ranges from few minutes to 30 min, depending on the analyte and the permeation properties of the sampling membrane.

The experimental set-up consists of Bruker Vector 22 FT-IR spectrometer with an externally aligned 50 cm long silica HWG coupled to the SCMS, which is immersed into a glass flask filled with analyte solution and kept under constant stirring.

Aqueous solutions of benzene, toluene, xylene isomers and chloroform were qualitatively and quantitatively analyzed confirming the feasibility of this sensor approach for environmental analysis.     

Analysis of Malodorous Sulfur Gases and Volatile Organometalloid Compounds in Landfill Gas Emissions Using Capillary Gas Chromatography with Programmed Temperature Vaporization Injection and Atomic Emission Detection

Volatile compounds containing Group V and Group VI elements in landfill gases are of concern as a source of toxic pollutants and unpleasant odors. Conventional analytical techniques for these compounds e.g. ICP-MS, ICP-AES are complicated, expensive and time consuming. The use of a simple programmed temperature vaporization injection (PTV) technique coupled to gas chromatography with atomic emission detection (GC-AED) has been successfully demonstrated to identify compounds containing arsenic, antimony, and sulfur in landfill gas. With an adapted PTV injection system (using a combination of a ten-port and a six-port Valco valves), problems associated with AED discharge tube damage due to high carrier gas flow rate during sample loading can be overcome. The gas samples generated from both a laboratory biowaste digester and a domestic landfill site were characterized using these techniques. Large sample gas volumes were adsorbed onto a cooled sorbent trap containing Porapak Q, followed by rapid liberation onto a porous layer open tubular column (PLOT) using programmed thermal desorption. Arsenic and antimony were also detected in the landfill leachate collected from the same landfill site using hydride generation-atomic absorption spectrometry (Hy-AAS). The efficiency of different traps has also been compared.     

TiO2悬浮体系光催化降解反应动力学模型的建立

以纳米材料TiO2作为光催化剂,乙酰甲胺磷（DMAPT）作为目标化合物,在DGF－1型多功能光化学反应仪上研究了悬浮体系TiO2光催化降解反应的动力学模型,模型中的主要参数有：TiO2用量、入射光强、反应器的几何半径、反应器的经验参数、反应物初始浓度、羟基自由基二级速率常数及已知化合物的物理性质（分子的摩尔体积和溶解度）。模型较好地预测了其他化合物（如三氯乙烯（TCE)、四氯乙烯（PCE0、对－二氯苯（DCB）和四氯化碳（CTC）的光催化降解,对C0（TCE）＝22.1mg/L,C0(PCE)=20mg/L和C0(PCE)=40mg/L的反应物,完全降解所需的时间分别为3,4和5min,入射光强在1.38－6.05W/cm^2范围时,反应速率与光强的0.5次方成正比,催化剂最佳用量随着入射光的增强而增加。     

A Versatile CuII Metal–Organic Framework Exhibiting High Gas Storage Capacity with Selectivity for CO2: Conversion of CO2 to Cyclic Carbonate and Other Catalytic Abilities

A linear tetracarboxylic acid ligand, H₄L, with a pendent amine moiety solvothermally forms two isostructural metal–organic frameworks (MOFs) L_M (M=Zn^II, Cu^II). Framework L_Cu can also be obtained from L_Zn by post‐ synthetic metathesis without losing crystallinity. Compared with L_Zn , the L_Cu framework exhibits high thermal stability and allows removal of guest solvent and metal‐bound water molecules to afford the highly porous, L_Cu′ . At 77 K, L_Cu′ absorbs 2.57 wt % of H₂ at 1 bar, which increases significantly to 4.67 wt % at 36 bar. The framework absorbs substantially high amounts of methane (238.38 cm³ g^?1, 17.03 wt %) at 303 K and 60 bar. The CH₄ absorption at 303 K gives a total volumetric capacity of 166 cm³ (STP) cm^?3 at 35 bar (223.25 cm³ g^?1, 15.95 wt %). Interestingly, the NH₂ groups in the linker, which decorate the channel surface, allow a remarkable 39.0 wt % of CO₂ to be absorbed at 1 bar and 273 K, which comes within the dominion of the most famous MOFs for CO₂ absorption. Also, L_Cu′ shows pronounced selectivity for CO₂ absorption over CH₄, N₂, and H₂ at 273 K. The absorbed CO₂ can be converted to value‐added cyclic carbonates under relatively mild reaction conditions (20 bar, 120 °C). Finally, L_Cu′ is found to be an excellent heterogeneous catalyst in regioselective 1,3‐dipolar cycloaddition reactions (“click” reactions) and provides an efficient, economic route for the one‐pot synthesis of structurally divergent propargylamines through three‐component coupling of alkynes, amines, and aldehydes.     

A Comparison Of Measurement of Homovanillic Acid in Brain Tissue by Gas Chromatography Mass Spectrometry and Liquid Chromatography with Electrochemical Detection

Abstract

A comparison of liquid chromatography with electrochemical detection (LCEC) and gas chromatography mass spectrometry (GCMS) has been made for analysis of homovanillic acid (HVA) in rat brain tissue. The LCEC procedure gave slightly higher average values of HVA in the samples measured; however, the HVA content determined by both methods related significantly. Rat brain meostriatum was used as representative samples for comparison of the two analytical procedures.     

基于掺杂金属有机骨架CeDUT-52分散固相萃取/高效液相色谱法检测水中的双酚类化合物

利用溶剂热法构筑了CeDUT-52吸附剂,将其用于水中双酚A(BPA)、双酚F(BPF)和双酚AF(BPAF)3种双酚类化合物的分散固相萃取(DSPE),并结合高效液相色谱-紫外检测,建立了水中3种双酚类化合物的分析方法.采用X射线衍射仪(XRD)、傅里叶变换红外光谱(FT-IR)、扫描电子显微镜(SEM)和X射线能谱...     

顶空固相微萃取-气相色谱/质谱法分析鉴定畜禽粪便中的挥发性有机化合物

采用顶空固相微萃取(HS-SPME)-气相色谱/质谱法(GC/MS)测定了牛粪、猪粪以及鸡粪中的挥发性有机化合物(VOCs)。在优化HS-SPME条件的基础上,通过GC/MS分析,从牛粪中分离鉴定出44种VOCs,从猪粪中分离鉴定出40种VOCs,从鸡粪中分离鉴定出41种VOCs。HS-SPME-GC/MS具有简单、快速、无需有机溶剂等特点,适合于畜禽粪便中挥发性有机化合物的分析与鉴定。同时,该研究揭示了畜禽养殖场臭味物质的来源,为治理其环境污染提供了科学依据。     

PDMS Rod-SBSE System Coupled with Gas Chromatography for Determination of PAHs in Aqueous Samples

A method for the analysis of trace polycyclic aromatic hydrocarbons(PAHs) in aqueous samples has been established by polydimethylsiloxane(PDMS) rod aided stir bar sorptive extraction(SBSE). The homemade PDMS rod has a size of 30 mm?3 mm o.d. with a volume of ca. 200 ?L, stable in thermal desorption process. The enriched PAHs by the PDMS rod were released in a homemade thermal desorption system coupled with gas chromatography. Experimental parameters for extraction of six PAHs were optimized including extraction time, pH, ionic strength and temperature of solution. The procedure has good recoveries of 80.0%―100.3% and very low limits of detection of 4.0―33 ng/L. PAHs in rain and river water were analyzed by this method.     

A PCP Pincer Ligand for Coordination Polymers with Versatile Chemical Reactivity: Selective Activation of CO2 Gas over CO Gas in the Solid State

A tetra(carboxylated) PCP pincer ligand has been synthesized as a building block for porous coordination polymers (PCPs). The air‐ and moisture‐stable PCP metalloligands are rigid tetratopic linkers that are geometrically akin to ligands used in the synthesis of robust metal–organic frameworks (MOFs). Here, the design principle is demonstrated by cyclometalation with Pd^IICl and subsequent use of the metalloligand to prepare a crystalline 3D MOF by direct reaction with Co^II ions and structural resolution by single crystal X‐ray diffraction. The Pd?Cl groups inside the pores are accessible to post‐synthetic modifications that facilitate chemical reactions previously unobserved in MOFs: a Pd?CH₃ activated material undergoes rapid insertion of CO₂ gas to give Pd?OC(O)CH₃ at 1 atm and 298 K. However, since the material is highly selective for the adsorption of CO₂ over CO, a Pd?N₃ modified version resists CO insertion under the same conditions.