Exact solution of heat transfer from a stretching surface with variable heat flux

An exact expression of the temperature distribution is constructed for the heat transfer from a stretching surface with prescribed power law heat flux. The stretching velocity is inversely proportional to the one third power of the distance measured along the surface from a thin slit. The final result is expressed in terms of hypergeometric functions. Although the exact solution is accomplished, some physically unrealistic phenomena are encounters for specific conditions. The temperature parameter which prescribe the surface heat flux, strongly affects those situations. Two types of temperature distribution are discussed: dimensionless temperatures with and without scaling to the dimensionless surface temperature. The expression of the temperature distribution without scaling is lucid to understand the heat transfer characteristics. Received on 23 July 1997     

Conjugate heat transfer with radiation from a vertical circular pin in a non-newtonian ambient medium

An analysis is presented for the heat transfer characteristics of a steady, laminar, mixed convective flow of power-law type non-Newtonian fluid over a circular pin by the conjugate convection-conduction theory including radiative effects under optically thick limit approximation. Numerical results are presented for the dimensionless heat transfer coefficients, local and overall heat fluxes and temperature distribution of the pin by a simultaneous solution of the convective boundary layer equations of the fluid and the energy equation of the pin.     

Investigation of temperature statistic characteristics in turbulent water flow with unsteady heat transfer

The results of an experimental study of a temperature field and its statistical characteristics in turbulent water flow upon a sudden change of heat generation in the channel wall are reported. Measurements were performed in 5 mm × 40 mm, 10 mm × 40 mm, and 20 mm × 40 mm channels in the regions of thermal stabilization and stabilized heat transfer at Reynolds numbers of (0.8–6.8) × 10⁴. The measurement results are generalized using a dimensionless time scale. The results of the calculation of heat transfer coefficients at unsteady heat transfer are presented.     

Direct contact heat transfer from an immiscible liquid jet

Temperature distribution and transfer of heat in a vertical, immiscible, liquid jet in direct contact with a liquid matrix are analyzed. A theoretical model for plug and parabolic flow is adopted from the literature, the treatment of a special V-shaped velocity distribution expected in the experiment and suitable for reactor application is calculated. Two common surface conditions, i.e. constant heat flux or constant temperature are considered. An experiment was performed in which a high Prandtl number fluid (oil) formed the jet and a low Prandtl number fluid (water) formed the matrix. The experimental results fall within theoretical results obtained for a V-type velocity distribution and plug flow. It was determined that the heat transfer characteristics of a direct contact jet flow in most cases have definite advantages over those of flow in a pipe beyond the obvious advantage of removal of the pipe wall's thermal resistance. These advantages result from the more flat velocity distribution encountered in jet flow as compared to a corresponding Laminar pipe flow. The likeliness of having a particular flow shape is discussed. Advantages of a central wire, leading to the V-type flow, are the enhancement of heat transfer and the stabilisation of the jet for any desired length. The jet flow is laminar.     

Experimental study of heat transfer characteristics due to confined impinging two-dimensional jets

Experimental results are presented for characteristics of impingement heat transfer caused by three slot jets. Experimental values were obtained for the dimensionless distance H = 0.5−3, dimensionless pitch P = 6−16, and Reynolds number Re = 500−8000. For laminar impinging flow, they were compared with numerical results. For turbulent impinging flow, two peaks of the local Nusselt number were obtained behind the second nozzle. The position of the second peak approached the nozzle as the space between nozzle and impinged surface decreased. The average Nusselt number between the central and second nozzles was determined from the ratio P/H and the Reynolds number based on the pitch of the nozzles.     

Cross-flow heat transfer in fixed bed

Radial flow reactor operated at cross-flow heat transfer is focused for large scale methanol synthesis. The effects of operating conditions including the reactor inlet air temperature, the heating pipe temperature and the air flow rate on the cross-flow heat transfer were investigated and results show that the temperature profile of the area in front of the heating pipe is slightly affected by all the operating conditions. The main area whose temperature profile is influenced is located behind the heating pipe. The heat transfer direction is related to the direction of the flow. In order to obtain the basic parameters for radial flow reactor designing calculation, the dimensionless number group method was used for data fitting of the bed effective thermal conductivity and the wall heat transfer coefficient which were calculated by the mathematical model with the product of Reynolds number and Prandtl number. The comparison of experimental data and calculated values shows that the calculated values fit the experimental data satisfactorily and the formulas can be used for reactor designing calculation.     

Combined natural convection heat and mass transfer in an enclosure having finite thickness walls

Unsteady three-dimensional conjugate heat and mass transfer in an enclosure having finite thickness heat-conducting walls has been analyzed numerically. The governing unsteady, three-dimensional flow, energy and contaminant transport equations for the gas cavity and unsteady heat conduction equation for solid walls, written in dimensionless terms of the vector potential functions, the vorticity vector, the temperature and the concentration, have been solved using an iterative implicit finite-difference method. Main attention was paid to the effects of the Rayleigh number, buoyancy ratio and the dimensionless time on the flow structure and heat and mass transfer regimes. It should be noted that the dominant cause of the oscillations in the dimensionless time dependences of the average Nusselt number on the heat source surface and the average Sherwood number on the contaminant source surface at Ra>5?10⁵ is the mutual influence of the analyzed object geometry and the thermo-diffusivity impact on the flow. The change in the buoyancy ratio can lead to the essential modifications of the flow, temperature and concentration fields owing to the significant influence of the concentration gradient.     

Free convection on a vertical plate with uniform and constant heat flux in a thermally stratified micropolar fluid

This paper analyzes flow and heat transfer characteristics of the free convection on a vertical plate with uniform and constant heat flux in a thermally stratified micropolar fluid. The dimensionless forms of boundary layer equations and their associated boundary conditions have been derived and the numerical results have been obtained using the method of cubic spline collocation with a finite difference scheme. The effects of the micropolar and stratification parameters on the dimensionless wall temperature, skin friction parameter and wall couple stress are discussed.     

Investigation of nonstationary heat transfer when a hot turbulent jet interacts with a shield

An experimental and theoretical investigation has been made of nonsteady heat transfer between a shield and a hot turbulent jet impinging normally on it. A system of dimensionless parameters is found for simulating the nonsteady interaction of high-temperature jets with shields. A system of thermocouples was used to measure the spatial and temporal distributions of the temperature in a gas above a shield, and also on the surface and within the shield. A numerical investigation was made of the nonsteady heat transfer in a shield with boundary condition specified in the form of the experimental temperature distribution of the front surface of the shield and with allowance for convective and radiative loss of heat from the other surfaces of the shield. The obtained solution is used to find the characteristics of nonsteady heat transfer (the coefficient of heat transfer and the Stanton number) on the front surface of the shield. These characteristics are used to solve the problem of periodic exposure of a shield to a heat flow produced by the switching on of a high-temperature jet.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 2, pp. 130–138, March–April, 1979.     

Experimental investigation on heat transfer and frictional characteristics of vertical upward rifled tube in supercritical CFB boiler

Water wall design is a key issue for supercritical Circulating Fluidized Bed (CFB) boiler. On account of the good heat transfer performance, rifled tube is applied in the water wall design of a 600 MW supercritical CFB boiler in China. In order to investigate the heat transfer and frictional characteristics of the rifled tube with vertical upward flow, an in-depth experiment was conducted in the range of pressure from 12 to 30 MPa, mass flux from 230 to 1200 kg/(m² s), and inner wall heat flux from 130 to 720 kW/m². The wall temperature distribution and pressure drop in the rifled tube were obtained in the experiment. The normal, enhanced and deteriorated heat transfer characteristics were also captured. In this paper, the effects of pressure, inner wall heat flux and mass flux on heat transfer characteristics are analyzed, the heat transfer mechanism and the frictional resistance performance are discussed, and the corresponding empirical correlations are presented. The experimental results show that the rifled tube can effectively prevent the occurrence of Departure from Nucleate Boiling (DNB) and keep the tube wall temperature in a permissible range under the operating condition of supercritical CFB boiler.     

Natural convection due to solar radiation over a non-absorbing plate with and without heat losses

Natural convection over a non-reflecting, non-absorbing, ideally transparent semi-infinite vertical flat plate due to absorption of incident radiation (solar radiation) is considered. The absorbed radiation acts as a distributed source which initiates buoyancy-driven flow and convection in the absorbing layer. The plate when heated by the absorbing fluid loses heat to the surroundings from its external side. Solution of the governing equations of the flow under these circumstances is non-similar because of both the heat source term in the energy equation and the temperature boundary condition at the plate. A local non-similar technique is used to obtain solutions for a wide range of the dimensionless distance along the plate and of the dimensionless loss coefficient to the surroundings. The results show that the temperature distribution has a maximum temperature in the depth of the fluid rather than on the plate. A new definition for a local heat transfer coefficient between the plate and the absorbing fluid is introduced which is based on the local maximum temperature rise in the fluid. A formula to calculate this heat transfer coefficient is given for the anticipated range of the loss coefficient.     

Investigation of flow and heat transfer in corrugated-undulated plate heat exchangers

 An experimental and numerical investigation of heat transfer and fluid flow was conducted for corrugated-undulated plate heat exchanger configurations under transitional and weakly turbulent conditions. For a given geometry of the corrugated plates the geometrical characteristics of the undulated plates, the angle formed by the latter with the main flow direction, and the Reynolds number were made to vary. Distributions of the local heat transfer coefficient were obtained by using liquid-crystal thermography, and surface-averaged values were computed; friction coefficients were measured by wall pressure tappings. Overall heat transfer and pressure drop correlations were derived. Three-dimensional numerical simulations were conducted by a finite-volume method using a low-Reynolds number k–ɛ model under the assumption of fully developed flow. Computed flow fields provided otherwise inaccessible information on the flow patterns and the mechanisms of heat transfer enhancement. Received on 5 February 1999     

Local nonsimilarity solution for the impact of the buoyancy force on heat and mass transfer in a flow over a porous wedge with a heat source in the presence of suction/injection

Combined heat and mass transfer in free, forced and mixed convection flows along a porous wedge with internal heat generation in the presence of uniform suction or injection is investigated. The boundary-layer analysis is formulated in terms of the combined thermal and solute buoyancy effect. The flow field characteristics are analyzed using the Runge-Kutta-Gill method, the shooting method, and the local nonsimilarity method. Due to the effect of the buoyancy force, power law of temperature and concentration, and suction/injection on the wall of the wedge, the flow field is locally nonsimilar. Numerical calculations up to third-order level of truncation are carried out for different values of dimensionless parameters as a special case. The effects of the buoyancy force, suction, heat generation, and variable wall temperature and concentration on the dimensionless velocity, temperature, and concentration profiles are studied. The results obtained are found to be in good agreement with previously published works.     

Studies on convective heat transfer through helical coils

An experimental investigation on steady state convection heat transfer from vertical helical coiled tubes in water was performed for laminar flow regime. Three coils with curvature ratios as 0.0757, 0.064, 0.055 and range of Prandtl number from 3.81 to 4.8, Reynolds number from 3,166 to 9,658 were considered in this work. The heat transfer data were generated from 30 experiments conducted at constant water bath temperature (60 °C) for different cold water flow rates in helical coils. For the first time, an innovative approach of correlating Nusselt number with ‘M’ number is proposed which is not available in the literature and the developed correlations are found to be in good agreement with the work of earlier researchers. Thus, dimensionless number ‘M’ was found to be significant to characterize the hydrodynamics of fluid flow and heat transfer correlations in helical coils. Several other correlations based on experimental data are developed. To cover wide range of industrial applications, suitable generalized correlations based on extended parameters beyond the range of present experimental work are also developed. All these correlations are developed by using least-squares power law fit and multiple-regression analysis of MATLAB software. Correlations so developed were compared with published correlations and were found to be in good agreement. Comparison of heat transfer coefficients, friction factor and Nusselt number for different geometrical conditions is presented in this paper.     

Lie group analysis for thermophoretic and radiative augmentation of heat and mass transfer in a Brinkman-Darcy flow over a flat surface with heat generation

A boundary layer analysis is presented to investigate numerically the effects of radiation,thermophoresis and the dimensionless heat generation or absorption on hydromagnetic flow with heat and mass transfer over a flat surface in a porous medium.The boundary layer equations are transformed to non-linear ordinary differential equations using scaling group of transformations and they are solved numerically by using the fourth order Runge-Kutta method with shooting technique for some values of physical parameters.Comparisons with previously published work are performed and the results are found to be in very good agreement.Many results are obtained and a representative set is displayed graphically to illustrate the influence of the various parameters on the dimensionless velocity,temperature and concentration profiles as well as the local skin-friction coefficient,wall heat transfer,particle deposition rate and wall thermophoretic deposition velocity.The results show that the magnetic field induces acceleration of the flow,rather than deceleration(as in classical magnetohydrodynamics(MHD) boundary layer flow) but to reduce temperature and increase concentration of particles in boundary layer.Also,there is a strong dependency of the concentration in the boundary layer on both the Schmidt number and mass transfer parameter.     

The mist-annular transition during condensation and its influence on the heat transfer mechanism

Influence of the mist-annular transition on the heat transfer mechanism during condensation is studied. It is shown that the applicability of annular flow correlations cannot be extended with accuracy to the mist region and that a dimensionless parameter. We can be used in defining the departure from annular flow conditions. A heat transfer correlation is suggested for the mist region and shown capable of good agreement with a data base of different fluids and tube orientations.     

Forced convection heat transfer from an equilateral triangular cylinder at low Reynolds numbers

An unsteady two-dimensional numerical simulation is performed to investigate the forced convection heat transfer for flow past a long heated equilateral triangular cylinder in an unconfined medium for the low Reynolds number laminar regime. The Reynolds number considered in this study ranges from 50 to 250 with three different values of Prandtl number (Pr?=?0.71, 7 and 100). Fictitious confining boundaries are chosen on the lateral sides of the computational domain that makes the blockage ratio β?=?5?% in order to make the problem computationally feasible. An unstructured triangular mesh is used for the computational domain discretization and the simulation is carried out with the commercial CFD solver Fluent. The flow and heat transfer characteristics are analyzed with the streamline and isotherm patterns at various Reynolds numbers. The dimensionless frequency of vortex shedding (Strouhal number), drag coefficient and Nusselt numbers are presented and discussed. The results obtained are in good agreement with the available results in the literature.     

Effects of prescribed heat flux and transpiration on MHD axisymmetric flow impinging on stretching cylinder

A numerical treatment for axisymmetric flow and heat transfer due to a stretching cylinder under the influence of a uniform magnetic field and prescribed surface heat flux is presented. Numerical results are obtained for dimensionless velocity, temperature, skin friction coefficient and Nusselt number for several values of the suction/injection, magnetic and curvature parameters as well as the Prandtl number. The present study reveals that the controlling parameters have strong effects on the physical quantities of interest. It is seen that the magnetic field enhances the dimensionless temperature inside the thermal boundary layer, whereas it reduces the dimensionless velocity inside the hydrodynamic boundary layer. Heat transfer rate reduces, while the skin friction coefficient increases with magnetic field.     

A review on transient test techniques for obtaining heat transfer design data of compact heat exchanger surfaces

Accurate and reliable dimensionless heat transfer characteristic is very essential for the analysis of heat exchangers. It is also required for the rating and sizing problems of heat exchangers. One of the important experimental methods used to determine the heat transfer coefficient between the heat transfer surface of the heat exchanger and the flowing fluid is transient test techniques. The transient test techniques are usually employed to establish Colburn factor versus Reynolds number characteristics of a high NTU heat exchanger surfaces like compact or matrix heat exchangers. In those situations, a single-blow test, where only one fluid is used, is employed to conduct the transient test. The transient technique may have the fluid inlet temperature having a step change, periodic or an arbitrary rise/drop. In this paper, various transient test techniques that are used for the determination of heat transfer characteristics of high NTU heat exchanger surfaces are discussed.     

An experimental investigation of heat transfer and flow friction characteristics of louvered fin surfaces by the modified single blow technique

This paper describes the development of an experimental facility to determine the heat transfer and flow friction characteristics of heat exchange surfaces by the modified single blow technique and the application of this transient technique to evaluate the performance characteristics of louvered fin heat exchangers. The reliability of implementing the modified single blow technique on the developed test facility is borne out by the good agreement in the heat transfer and flow friction data for the parallel plate test core when compared with theoretical and empirical correlations available in the literature. Performance evaluation of two louvered fin surfaces used mainly for cooling of large land and marine based electrical power generator sets is carried out and compared with similar louvered fin surfaces available in the literature. On the basis of dimensionless area and power factors, it was found that the flat fin is slightly superior in overall performance than its corrugated counterpart for low Reynolds numbers. Both surfaces are however inferior in performance when compared with the flat fin surface of Achaichia and Cowell and the corrugated fin surface of Davenport. Use of the j/f ratio as an approximate figure of merit led to an inaccurate assessment of the performance of the louvered fin heat exchanger surfaces evaluated in this study. Received on 8 May 1998