Trition X-100/C_(10)H_(21)OH/H_2O体系层状液晶中纳米羟基磷灰石粉体的合成

本文以Triton X-100/C10H21OH/H2O体系层状溶致液晶为模板,Ca(NO3)2和(NH4)2HPO4为反应物,在一定的pH条件下,通过三元相图确定了层状液晶单相区域,并合成了羟基磷灰石(HA)纳米颗粒。用傅立叶红外光谱(FTIR),X射线衍射(XRD)和透射电子显微镜(TEM)对产物进行了表征。并考察了不同助表面活性剂浓度和不同表面活性剂浓度对产物的形貌和尺寸的影响。结果表明所制备的HA纳米颗粒平均直径为8~10nm、长度在100nm左右,呈针状。助表面活性剂浓度对HA形貌及尺寸影响不大,但是在一定范围内改变表面活性剂浓度可以起到调控HA纳米颗粒形貌和尺寸的作用。     

反相胶束法控制合成不同形貌半导体Ag_2S纳米晶

采用水 (溶液 ) /TritonX 10 0 /环已烷 /正戊醇反相胶束体系 ,制备出不同形貌的Ag2 S纳米晶 ,其中合成出的直径为 5 0～ 10 0nm、长度为 2 .0～ 3.5 μm、长径比为 2 0～ 70的纯相Ag2 S纳米棒为首次报导 .就不同ω0 、反应物浓度和陈化时间等因素对合成Ag2 S的形貌和尺寸的影响进行了研究 ,获得了控制合成不同形貌Ag2 S纳米晶的反应条件 .所得产物利用透射电子显微镜分析进行了表征     

氧化铜纳米片的水热合成与表征

利用水热法一步制备了形貌均一的氧化铜纳米片,借助场发射扫描电子显微镜、X射线粉末衍射仪和透射电子显微镜分析了产物的形貌和晶体结构;并研究了反应物浓度及表面活性剂等因素对氧化铜纳米结构的影响.结果表明,以氢氧化钠作为碱源时,在不添加任何表面活性剂的情况下,随着氢氧化钠浓度的升高,纳米片的尺寸减小、厚度增大;此外,通过添加不同的表面活性剂可以得到不同形貌的氧化铜纳米结构.     

ZnIn_2S_4的制备及其表面活性剂辅助的形貌控制生长

采用湿化学合成路线以巯基乙酸为包覆剂,水为溶剂制备了六方相ZnIn2S4。应用能谱分析(EDS)、X射线衍射(XRD)、透射电镜(TEM)、扫描电镜(SEM)和紫外-可见光谱对产物的组成、结构、形貌和光学性质进行了表征。结果表明,所得到的ZnIn2S4具有层状形貌。这些层状物是由ZnIn2S4纳米粒子前驱体在热处理过程中聚集生长而成的。另外,以ZnIn2S4纳米粒子前驱体为起始原料,借助表面活性剂的导向作用在固/液界面成功地实现了ZnIn2S4的形貌控制生长,得到了具有棒状、棒簇状、管簇状形貌的ZnIn2S4。根据实验结果,初步讨论了可能的表面活性剂辅助的ZnIn2S4形貌控制生长的机制。     

圆形片状纳米复合材料Ag/ZnO-ZrO2微波辅助合成与多模式光催化罗丹明B

采用微波辅助结合沉淀法制备了以Zn O为主体的纳米复合材料Ag/Zn O-Zr O_2。通过X射线粉末衍射(XRD)、紫外-可见漫反射吸收光谱(UV-Vis/DRS)、扫描电子显微镜(SEM)、X射线光电子能谱(XPS)和N2吸附-脱附等表征手段研究了微波辐射对Ag/Zn O-Zr O_2晶型结构、形貌及表面物理化学性质的影响。结果表明,在200 W微波辐射作用下,该样品晶型结构未发生明显变化,但Ag的衍射峰明显增强,同时,其晶粒尺寸、光吸收性质和表面物理化学性质等方面则发生改变,尤其是样品Ag/Zn O-Zr O_2的形貌呈现了圆形片状结构。分别在紫外和微波辅助条件下对纳米复合材料的光催化性能进行了一系列考察,同时为了进一步评价所合成样品在太阳光作用下的实用价值,又考察了Ag/Zn O-Zr O_2在模拟日光条件下的光催化性能。结果显示,紫外光作用下,纳米复合材料Ag/Zn O-Zr O_2的光催化活性高于市售P25以及未经微波处理的样品,且在微波辅助光催化条件下,其活性有较大程度提高。200 W微波功率下所合成样品Ag/Zn O-Zr O_2在模拟日光作用下显现出较高活性。另外,根据紫外光条件下对光催化活性物种的捕获实验提出了Ag/Zn O-Zr O_2可能的光催化机理。     

特殊形貌GdF3:Eu3+纳米发光材料的制备及性能

以PEG-2000、柠檬酸和甘氨酸为表面活性剂,采用水热法制备出扁平纳米棒、纳米花和纳米片状的GdF3:Eu3+发光材料,并对其结构和性能进行了表征.XRD结果表明,所得样品均为正交晶系.FESEM照片表明,使用不同表面活性剂所制备的产物形貌不同.研究了以PEG-2000为表面活性剂时反应物浓度对产物形貌的影响,并对其...     

4-十二烷氧基苄胺在纳米金微粒合成中的应用

以新型表面活性剂4-十二烷氧基苄胺(C12OBA)构成的C12OBA/正丁醇/正庚烷/丙醛/HAuCl4(aq)反相微乳液作为微反应器,利用微波辐射加热-丙醛还原法制备了C12OBA包覆金纳米微粒;利用透射电镜、傅立叶变换红外光谱仪及X射线衍射仪分析了产物的微观形貌、化学键合特征、晶体结构;并测定了其紫外-可见吸收光谱.结果显示,表面活性剂C12OBA既可参与形成稳定的反相微乳液,又可作为金纳米微粒的良好保护剂.反相微乳液液滴的微小水核以及C12OBA/金的物质的量之比对纳米金微粒的尺寸和形貌起到良好的控制作用.     

Ag纳米颗粒的快速制备及其性能研究

以黄药子提取液为还原剂和表面活性剂,快速制备出Ag纳米颗粒。通过紫外-可见分光光度计(UV-Vis)、透射电子显微镜(TEM)和X-射线衍射(XRD)对Ag纳米颗粒的形貌、成分和微观结构进行表征、分析。结果表明,Ag纳米颗粒为类球形,粒径为20.6 nm。说明了黄药子提取液具有良好的还原性。以合成的Ag纳米颗粒作为催化剂可以在10 min内将4-硝基苯酚(4-NP)完全降解,4-NP降解的速率常数可以通过Ag纳米颗粒的添加量来调节,最大值为0.286 min~(-1),说明合成的Ag纳米颗粒具有良好的光催化活性。     

ZnO纳米环的可控合成

以六次甲基四胺(Hexamethylenetetramine, C6H12N4)和水合硝酸锌[Zn(NO3)2·2H2O]为原料, 表面活性剂聚丙烯酰胺-氯化二烯丙基二甲基铵[poly(acrylamide-co-diallyldimethylammonium chloride, 缩写为PAM-CTAC]为形貌控制剂, 采用液相沉淀法合成了ZnO纳米环. 产物的结构与形貌经X射线粉末衍射(XRD)和扫描电子显微镜(SEM)表征. 研究了不同实验条件(如表面活性剂的浓度、反应物浓度、反应温度和反应时间等)对产物形貌与尺寸的影响. 讨论了PAM-CTAC作用下ZnO纳米环可能的形成机理. 结果表明, 合成产物为六方Wurtzite型结构的ZnO纳米环, 环内径约为220 nm, 壁厚约为70 nm. 反应物浓度、反应温度对ZnO纳米环的形成以及纳米环的尺寸都有一定的影响, 但起关键作用的是PAM-CTAC. 通过改变PAM-CTAC的浓度, 能有效地实现ZnO纳米环的可控合成. 室温荧光光谱显示, ZnO纳米环的紫外发射峰具有较窄的半高宽(FWHM)(约7 nm), 表明合成产物具有较窄的尺寸分布.     

圆形片状纳米复合材料Ag/ZnO-ZrO2微波辅助合成与多模式光催化罗丹明B

采用微波辅助结合沉淀法制备了以ZnO为主体的纳米复合材料Ag/ZnO-ZrO₂。通过X射线粉末衍射(XRD)、紫外-可见漫反射吸收光谱(UV-Vis/DRS)、扫描电子显微镜(SEM)、X射线光电子能谱(XPS)和N2吸附-脱附等表征手段研究了微波辐射对Ag/ZnO-ZrO₂晶型结构、形貌及表面物理化学性质的影响。结果表明, 在200 W微波辐射作用下, 该样品晶型结构未发生明显变化, 但Ag的衍射峰明显增强, 同时, 其晶粒尺寸、光吸收性质和表面物理化学性质等方面则发生改变, 尤其是样品Ag/ZnO-ZrO₂的形貌呈现了圆形片状结构。分别在紫外和微波辅助条件下对纳米复合材料的光催化性能进行了一系列考察, 同时为了进一步评价所合成样品在太阳光作用下的实用价值, 又考察了Ag/ZnO-ZrO₂在模拟日光条件下的光催化性能。结果显示, 紫外光作用下, 纳米复合材料Ag/ZnO-ZrO₂的光催化活性高于市售P25以及未经微波处理的样品, 且在微波辅助光催化条件下, 其活性有较大程度提高。200 W微波功率下所合成样品Ag/ZnO-ZrO₂在模拟日光作用下显现出较高活性。另外, 根据紫外光条件下对光催化活性物种的捕获实验提出了Ag/ZnO-ZrO₂可能的光催化机理。     

Morphology-dependent activity of silver nanostructures towards the electro-oxidation of formaldehyde

Morphological controlled silver nanoproducts have been prepared using the polyol process through varying the concentration of Na₂S. The relationship between the shape of Ag nanocatalyst and the activity for electro-oxidation of formaldehyde has also been investigated. The Ag nanoproducts were found to be efficient electrocatalysts for anodic oxidation of formaldehyde in alkaline solutions. Activity and selectivity were strongly dependent on the morphology of the silver nanoproducts. It was found that silver nanorods were more active than nanowires, nanopolyhedra and nanospheres.     

Destructive effect of solar light on morphology of colloidal silver nanocubes

Colloidal silver nanocubes (NCs) were successfully synthesized by reduction of silver nitrate with ethylene glycol and polyvinylpyrrolidon as capping agent. The effect of solar light irradiation on the formation and morphology of silver NCs was investigated. Moreover, altering the amount of sodium sulfide was used to control the morphology and shape of primary silver seeds. Scanning electron microscopy, transmitting electron microscopy, X-ray diffraction and UV-vis spectroscopy were used to characterize silver NCs. The samples prepared under the solar light irradiation do not possess cubic shape while highly monodispersed silver NCs were obtained in dark room conditions. For dark room synthesis, a decrease of the amount of Na₂S by only 10 μL resulted in formation of mixture of silver nanospheres and nanowires in addition to NCs instead of the monodispersed silver NCs. However, similar increase of the amount of sodium sulfide results in distortion of cubic geometry of particles. The results suggest that solar light has a negative effect on the shape evolution of the primary silver seeds.     

Kinetics of silver electrodeposition from thiocarbamide solutions at a regular surface coverage with sulfide ions

Kinetics of silver electrodeposition in the presence of sulfide ions is studied on electrodes renewed by cutting off a thin surface layer, at a controlled time of contact of the “fresh” surface with the electrolyte. Solutions containing 10^?2 M AgNO₃, 0.1 M thiocarbamide, 0.5 M HClO₄, and from 2 × 10^?6 to 1.5 × 10^?5 M Na₂S are studied. It is shown that under the studied conditions, the effect of silver electrodeposition on the surface concentration of sulfide ions is insignificant. As the concentration of sulfide ions in solution and their coverage on the electrode surface θ increase, the cathodic polarization decreases. Tafel curves plotted for θ = const are used in estimating the exchange current i ₀ and the transfer coefficient α. It is shown that α ≈ 0.5 and weakly depends on θ, whereas the exchange current increases with the increase in θ by an approximately linear law from 10^?5 A/cm² at θ ? 0 to 10^?4 A/cm² at θ = 0.43. The obtained data are compared with the results of kinetic studies of silver anodic dissolution in similar solutions.     

Kinetics of silver dissolution in sulfide containing thiocarbamide electrolytes

Effective values of reaction order with respect to ligand P, transfer coefficient α, and exchange current i ₀ at constant silver surface coverages θ by sulfide ions are measured. The employed solutions contained from 0.4 to 0.05 M thiocarbamide, 0.5 M HClO₄, 10^?4 M AgNO₃, and from 10^?5 to 10^?4 M Na₂S. It is shown that the exchange current grows approximately linearly from 10^?5 to 1.5 × 10^?4 A/cm² at θ increase in the range from zero to 0.8, while α and P values grow negligibly in the ranges of 0.4–0.45 and 0.9–1.1, accordingly. The obtained results are compared with the data of similar studies of the gold behavior in acidic thiocarbamide solutions. The possible reasons for the different effects of sulfide ion chemisorption on the anodic dissolution of gold and silver in the studied solutions are discussed.     

Investigation of the interaction between cobalt sulfide coatings and Ag(I) ions using cyclic voltammetry in KClO4 and NaOH aqueous solutions and X-ray photoelectron spectroscopy

Cobalt sulfide coatings have been investigated by means of cyclic voltammetry in 0.1 M KClO₄ and 0.1 M NaOH solutions and analyzed using X-ray photoelectron spectroscopy. They have been shown to contain CoS(OH), CoS and Co(OH)₂. After treating such Co sulfide coatings with AgNO₃ solution, their composition changes: both the cobalt and oxygen content decreases and Ag (up to 85 at%) appears in the coating as Ag₂S, Ag₂O and metallic Ag. Co(II) compounds react with Ag⁺ ions according to an exchange reaction [CoS+2Ag⁺+2H₂O→Ag₂S+Co(OH)₂+2H⁺]. In the course of the reaction of Co(OH)₂ with silver ions, a redox process occurs, giving metallic silver [Co(OH)₂+Ag⁺+H₂O→Ag°+Co(OH)₃+H⁺ or Co(OH)₂+Ag⁺→Ag°+CoO(OH)+H⁺]. Ag₂S reduction takes place at more positive potentials than Cu reduction; therefore sulfide layers of cobalt modified with silver ions, unlike unmodified ones, may be plated with Cu from both acid and alkaline electrolytes. Electronic Publication     

Micro-Raman Spectroscopy of Nanostructured Silver Sulfide

Nanostructured silver sulfide powder with an average particle size of about 45 nm, an acanthite α-Ag₂S monoclinic structure (space group P2₁/c), and nonstoichiometric composition Ag_1.93S has been synthesized by the chemical deposition method. The silver sulfide nanopowder has been studied by Raman spectroscopy. According to the Raman scattering data, heating the nanopowder with high-power laser radiation in air leads to photoinduced decomposition of the Ag_1.93S nanopowder to give silver metal. The Raman spectrum of the silver sulfide nanopowder shows a series of bands in the low-frequency range from 90 to 260 cm^–1 associated with vibrations of silver atoms, Ag–S bonds, and symmetric Ag–S–Ag longitudinal modes. Raman spectroscopy confirmed an acanthite monoclinic structure of synthesized silver sulfide nanopowder.     

Large-scale synthesis of silver nanowires and platinum nanotubes

Silver nanowires have been synthesized by ethylene glycol reduction of silver nitrate with the assistance of polyvinyl pyrrolidone and sodium sulfide in a large scale. By adjusting the reaction temperature and Na₂S content, silver nanowires with lengths up to 3?4 μm can be achieved in high yield. Scanning electron microscopy, transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected areas electron diffraction (SAED), and X-ray diffraction (XRD) have been employed to characterize silver nanowires. Platinum nanotubes with length about 3 μm can be prepared using as-prepared silver nanowires as sacrificial templates. Platinum nanotubes were characterized by TEM, SAED, and HRTEM.     

Ag3PO4/Ag2S/g-C3N4复合光催化剂的制备与性能

通过沉积法和离子交换法成功地制备了Ag_3PO_4/Ag_2S/g-C_3N_4复合型光催化剂。利用X射线多晶粉末衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、N_2吸附-脱附等温线、紫外-可见漫反射光谱、荧光光谱等手段对样品进行了表征。通过降解罗丹明B考察其可见光催化活性及稳定性,研究了硫化钠与磷酸银物质的量的比值(n_(Na_2S)/n_(Ag_3PO_4))、g-C_3N_4添加量对所制备复合光催化材料性能的影响,同时对光催化机理进行了探讨。结果表明,随着n_(Na2S)/n_(Ag3PO4)的增加,所得复合催化材料活性先增加后降低;当n_(Na2S)/n_(Ag_3PO_4)为1.5%、g-C_3N_4与Ag_3PO_4的质量比为3∶7时制备的催化剂ASC1.5的光催化活性最好,在可见光照射下,40 min内可将罗丹明B完全降解,且5次循环使用后仍保持较高的催化活性。和Ag_3PO_4相比,Ag_3PO_4/Ag_2S/g-C_3N_4复合型光催化材料的活性与稳定性都得到明显提高,这主要归因于复合催化剂比表面积和孔结构的增加,载流子分离效率的提高。光催化机理研究表明,空穴(h~+)、超氧阴离子自由基(·O~(2-))和羟基自由基(·OH)都是光催化过程中的主要活性物种。三者作用大小依次为:h~+·O~(2-)·OH。     

Synthesis and Characterization of Silver Sulfide Nanoparticles Containing Sol-Gel Derived HPC-Silica Film for Ion-Selective Electrode Application

Silver sulfide nanoparticles dispersed in sol-gel derived hydroxypropyl cellulose (HPC)-silica films have been successfully synthesized using H₂S gas diffusion method. This is the first attempt to produce silver sulfide nanoparticles using this technique. Ag₂S nanoparticles are generated through reaction of H₂S gas with AgNO₃ precursor dissolved in the HPC-silica matrix. Transmission electron microscope (TEM) and atomic force microscope (AFM) analysis reveal nanoparticles size distribution from 2.5 nm to 56 nm for H₂S gas exposed sample. The surface chemistry of Ag₂S nanoparticles and sol-gel derived HPC-silica matrix is confirmed by X-ray photoelectron spectroscopy (XPS). The negative shifts in the core-level XPS Ag (3d) binding energy of Ag₂S nanoparticles are attributed to Ag : S surface atomic ratio exhibited by these nanoparticles with varying processing conditions. Following processing and characterization, suitability of the present method to produce silver sulfide ion-selective electrode is demonstrated by depositing Ag₂S nanoparticles on a graphite rod. The high reponse function of the electrode is due to the presence of nanoparticles.     

Effect of temperature and water as additive on the MW and thermal properties of copoly(p-phenylene/biphenylene sulfide)s

Copoly(p-phenylene/biphenylene sulfide)s, PPBS were prepared from sodium sulfide trihydate(Na₂S·3H₂O), p-dichlorobenzene (DCB), and 4,4′-dibromobiphenyl (DBB) comonomers in N-methyl-2-pyrrolidinone (NMP) solvent using an autoclave. The molecular weights of PPBS copolymers were determined by high temperature (210°C) GPC in 1-chloronaphthalene solvent. The reaction temperature had little effect on the molecular weights of PPBS copolymers with water as additive at the level of 3 mol H₂O per 1 mol Na₂S. PPBS copolymer, however, showed maximum molecular weight of M_w = 24.1 × 10³ with the total water content of 9 mol H₂O per 1 mol Na₂S at an optimum polymerization temperature of 270°C. The resulting PPBS copolymer sample showed higher T_g (by 30°C) and lower T_m (by 10°C) than PPS homopolymer prepared under similar conditions. © 1996 John Wiley & Sons, Inc.