带加速度补偿平面型光纤光栅水听器探头技术的研究

针对平面型光纤Bragg光栅(Fiber Bragg Grating,缩写为FBG)水听器探头加速度响应明显,影响它对正常声压进行探测的需求,提出了采用加速度补偿措施进行加速度去敏这一有效方法。从理论和实验上分析研究了带加速度补偿平面型光纤FBG水听器探头的结构灵敏度、灵敏度频率响应特性和加速度响应特性。结果表明:采用加速度补偿措施后,单位加速度(1m·s^-2)响应输出的等效作用声压由2.52~3.26 Pa降为0.0758~0.217 Pa。同时,探头结构灵敏度由28 fm/Pa减小为20 fm/Pa,动态谐振频率由6.2 kHz增高为6.52 kHz。谐振频率的增加有助于提高水听器系统的动态响应特性,而结构灵敏度的降低,可以通过提高FBG动态波长解调仪的灵敏度来进行补偿。本来,光纤光栅或光纤光栅激光水听器系统可探测灵敏度主要由解调仪灵敏度决定,而不是由探头结构灵敏度决定。所以,该加速度补偿措施具有很大的实用性。     

Research of the planar optical fiber Bragg grating hydrophone probe

This paper presents the planar Fiber Bragg Grating （FBG） hydrophone probe sensing principle, and theoretically and experimentally researches the probe structure sensitivity, the receiving sensitivity frequency response characteristic and the acceleration response property. Planar sheet is made of stainless steel, its thickness is 0.15 mm, its diameter is 15mm, and the length of hollow circular shell is 20 mm. For this size of the structure, the probe structure sensitivity is up to 23 fm/Pa, which is about 7300 times of the value of the bare fiber. The resonance frequency is 6.5 kHz, and the amplitude-frequency curve of the receiving sensitivity response is relatively flat within the frequency range of 100 Hz to 5.5 kHz. The output yielded by one unit acceleration （1m/s2） is equivalent to （2.52 to 3.26 Pa） acoustic pressure acting output. This probe structure is easy to form FBG hydrophone array by multiplexing technique. The research shows that this planar structure not only can form FBG hydrophone probe, but also can constitute optical FBG laser hydrophone probe. The structure can realize different bandwidth, different range acoustic pressure measurement by adjusting the geometrical size of the sheet.     

一种平面型光纤光栅水听器探头技术的研究

阐述了一种平面薄板结构的平面型光纤Bragg光栅(Fiber Bragg Grating,缩写为FBG)水听器探头的工作原理,从理论和实验上分析研究了该探头的结构灵敏度、频率响应特性以及加速度响应特性。平面圆形薄板采用不锈钢,尺寸为:直径15 mm、厚度0.15 mm,探头为圆柱型,尺寸为:直径17 mm、长20 mm。对于该尺寸结构的FBG水听器,探头静态灵敏度可达23 fm/Pa,比裸光栅增敏7300倍;谐振频率为6.5 kHz,而且幅频特性在100 Hz~5.5 kHz频率范围内较为平坦;低频段加速度响应灵敏度为:58~75(fm·s^2/m),在1 m/s^2加速度作用下其输出等效(2.52~3.26 Pa)压力作用下的输出。该结构的探头也便于多路复用组成水听器阵列。该平面结构不仅可以组成光纤FBG水听器探头,同样可以组成光纤光栅激光水听器探头。对薄板的几何尺寸进行适当的调整,可实现不同量程、不同带宽的水声压力测量。     

High-sensitivity,fiber-optic,flexural disk hydrophone with reduced acceleration response

Abstract

A hydrophone consisting of a hollow cylinder whose flexible, circular end plates are bonded to pairs of pat, spiral wound coils of optical fiber is described. When the end plate/disk is deformed due to a pressure difference, the outer and inner fiber coils experience opposite strains resulting in a “push—pull” optical path length difference which is detected in an all-fiber Michelson interferometer. The close proximity of the interferometric fiber coils, separated by the thin thermally conducting end plate, rejects thermal gradient-induced signals. The addition of a second identical end plate and fiber coil pair at the opposite end of the cylinder will double the acoustic sensitivity while canceling acceleration induced signals. The calculated and measured optical strain of a single simply supported plate, single-coil sensor (8.0 cm diameter, 3.0 mm thickness) using static pressure, acoustic pressure, and acceleration are in good agreement and yield a sensitivity of 0.21 rad/Pa (ΔΦ/ΦΔP = -301 dB re I μPa-1) below its resonance frequency of 3 kHz. The calculated and measured strain for a dual clamped disk (4.5 cm diameter, 1.0 mm thickness) acceleration-canceling sensor with four 8-m coils are in good agreement also and yield a sensitivity of 1.0 rad/Pa (ΔΦ/ΦpΔP = -291 dB re 1 μPa^?1) below the disk resonance frequency of 4.5 kHz. These are the highest fiber-optic, omnidirectional hydrophone sensitivities reported to date.     

一种耐静压分布反馈式光纤激光水听器探头设计

大深度工作环境下,静水压会引起分布反馈式光纤激光水听器反射中心波长漂出解调系统的复用窗口,使水听器无法解调目标声压信号;不同的静水压也会引起分布反馈式光纤激光水听器灵敏度的变化,影响光纤激光水听器阵列的一致性。基于电力声类比理论,提出带静压补偿的分布反馈式光纤激光水听器探头,建立结构的声压传递函数,分析各结构参数对传递函数的影响,为分布反馈式光纤激光水听器探头频率响应平坦化设计提供理论依据。加工制作了耐静压分布反馈式光纤激光水听器样品进行测试,在0 kHz～10 kHz频率范围内声压灵敏度波动范围不大于±2.4 dB,2.3 MPa内出射激光中心波长漂移量不大于0.06 nm,对深水光纤激光水听器的研究具有指导意义。     

High-sensitivity, fiber-optic, flexural disk hydrophone with reduced acceleration response

A hydrophone consisting of a hollow cylinder whose flexible, circular end plates are bonded to pairs of pat, spiral wound coils of optical fiber is described. When the end plate/disk is deformed due to a pressure difference, the outer and inner fiber coils experience opposite strains resulting in a “push—pull” optical path length difference which is detected in an all-fiber Michelson interferometer. The close proximity of the interferometric fiber coils, separated by the thin thermally conducting end plate, rejects thermal gradient-induced signals. The addition of a second identical end plate and fiber coil pair at the opposite end of the cylinder will double the acoustic sensitivity while canceling acceleration induced signals. The calculated and measured optical strain of a single simply supported plate, single-coil sensor (8.0 cm diameter, 3.0 mm thickness) using static pressure, acoustic pressure, and acceleration are in good agreement and yield a sensitivity of 0.21 rad/Pa (ΔΦ/ΦΔP = -301 dB re I μPa-1) below its resonance frequency of 3 kHz. The calculated and measured strain for a dual clamped disk (4.5 cm diameter, 1.0 mm thickness) acceleration-canceling sensor with four 8-m coils are in good agreement also and yield a sensitivity of 1.0 rad/Pa (ΔΦ/ΦpΔP = -291 dB re 1 μPa^-1) below the disk resonance frequency of 4.5 kHz. These are the highest fiber-optic, omnidirectional hydrophone sensitivities reported to date.     

Development of an optical fiber hydrophone with fiber Bragg grating

A new type of optical fiber hydrophone is constructed with a fiber Bragg grating (FBG) based on the intensity modulation of laser light in an FBG under the influence of sound pressure. The FBG hydrophone shows linearity, with dynamic range about 70 dB. It can measure amplitude and phase of an acoustic field in real time, and operates in a wide range of acoustic frequency, at least from 1 kHz to 3 MHz. No signal distortion is observed in the detected signal. Because of the simplicity in its operating principle and geometry, an FBG hydrophone is expected to be an acoustic sensor of high practicality compared to a conventional optical fiber hydrophone.     

ZnO薄膜硅微压电矢量水听器

提出了一种基于ZnO压电薄膜的硅微压电矢量水听器,其核心部件是利用微电子机械系统(MEMS)技术制作的悬臂梁结构压电加速度计。由近似解析和有限元分析,得出加速度计的灵敏度和谐振频率,并在此基础上对其进行了优化设计。研制了MEMS压电加速度计,并装配后构成MEMS矢量水听器。测试结果表明:加速度灵敏度在20~1,200 Hz范围内约为0.83 mV/(m/s²)。经过液柱法测量,在1 kHz时,MEMS矢量水听器等效声压灵敏度为-229.5 dB (ref.1V/μPa),比同类型压阻式MEMS矢量水听器的灵敏度高17 dB以上。     

Miniature photonic-crystal hydrophone optimized for ocean acoustics

This work reports on an optical hydrophone that is insensitive to hydrostatic pressure, yet capable of measuring acoustic pressures as low as the background noise in the ocean in a frequency range of 1 Hz to 100 kHz. The miniature hydrophone consists of a Fabry-Perot interferometer made of a photonic-crystal reflector interrogated with a single-mode fiber and is compatible with existing fiber-optic technologies. Three sensors with different acoustic power ranges placed within a sub-wavelength sized hydrophone head allow a high dynamic range in the excess of 160 dB with a low harmonic distortion of better than -30 dB. A method for suppressing cross-coupling between sensors in the same hydrophone head is also proposed. A prototype was fabricated, assembled, and tested. The sensitivity was measured from 100 Hz to 100 kHz, demonstrating a sound-pressure-equivalent noise spectral density down to 12 μPa/Hz(1/2), a flatband wider than 10 kHz, and very low distortion.     

一种有源型光纤水听器原理与实验分析

分析了一种有源型光纤水听器的水声传感原理,在一段掺铒光纤中写入具有π相移的光纤光栅构成光纤激光器,水声压力作用在激光器上引起激光波长的移位,采用干涉法检测出波长移位引起的相位变化即得到声压的信息.水声探测实验表明,有源型光纤水听器的声压灵敏度为-166.5 dB(参考值1 rad/μPa).将不同工作波长的四元光纤水听器串接于一根光纤内组成水听器阵列,使用带通波分复用器将阵列发出的激光分离至各独立通道后检测出相应的声压信号,测得水听器之间的级串扰小于-60 dB,且单元水听器水声响应的动态范围不受影响.     

新型光纤光栅水声传感器的研究

提出了一种新型的光纤布拉格光栅(FBG)水声传感探头结构以及光纤光栅传感信号的自解调方法。利用一对匹配光栅构成推挽结构,实现了传感-解调的合二为一,大大地减小了系统的复杂度;并通过筒状弹性体结构,解决了裸光纤光栅测量水声信号的灵敏度过小的问题,并具有温度补偿作用。仿真与初步实验结果表明,该水听器探头的测量动态范围超过100 dB,在100~200 dB re 1μPa的水声压范围内,测量灵敏度为0.36 nm/Mpa。     

光纤光栅水听器技术实验研究

采用光纤布喇格光栅作为基本传感器件, 设计制作了光纤光栅水听器. 利用匹配光纤光栅解调技术, 实现了高灵敏度、高速度的动态信号测量, 并进行了相关的水下声音测量实验. 实验系统可测量水声信号频率范围为10 Hz~3 kHz, 测量动态范围为60 dB, 其结果具有很高的线性度.     

光纤Bragg光栅水听器探头的特性及实验研究

论述了FBG水听器探头基元——光纤Bragg光栅(FBG)的传感特性,分析了FBG的耦合系数、反射率、反射带宽和栅长对FBG水听器传感特性的影响。通过改进FBG水听器探头封装结构,增加了其压力敏感系数。并将实验结果与标准水听器(压电型)比较,标定出FBG的声压灵敏度,在1～25KHz的声波检测范围,其响应平坦度好、信号输出稳定,改进措施是有效的。     

Remote fiber sensor based on cascaded Fourier domain mode-locked laser

We propose a high-speed remote fiber Bragg grating (FBG) sensor interrogation system based on a 1.3-μm cascaded Fourier-domain mode-locked (FDML) laser. It consists of multiple FBGs connected to an optical circulator in the laser cavity. The cascaded FDML laser with these multiple FBGs is operational when the scanning frequency of the fiber Fabry-Perot tunable filter matches the fundamental frequency of the laser cavity. Each FBG provides a separate laser cavity for the FDML laser. The scanning frequencies of each laser cavity are 30.5314, 31.5393, 32.7108, and 33.8023 kHz. Using the cascaded FDML laser, we measure the performance of the long-distance static strain FBG sensor interrogation system in both the time and spectral domains. The slope coefficients of the measured relative wavelength difference and the relative time delay from the static strain are found to be 0.95 pm/μstrain and 0.15 ns/μstrain, respectively. We also demonstrate the dynamic response of the interrogation system with 80-Hz modulation strain using the cascaded FDML laser. Thus, an FBG sensor interrogation system for high-speed and high-sensitivity long-distance monitoring systems can be realized using a cascaded FDML laser.     

带加速度补偿的DFB光纤激光水听器

针对分布反馈式光纤激光水听器在用于水声探测时极易受加速度效应干扰的问题,设计了一种双膜片对称结构的光纤激光水听器,对该水听器的抗加速度性能进行了研究.建立了双膜片结构水听器的加速度灵敏度理论模型,分析了水听器各部件的尺寸大小、材料参量与水听器加速度灵敏度的关系,实现了对水听器结构的优化设计;加工制作了分布反馈式光纤激光水听器原型样品,并进行了实验研究.测量结果表明,在2.5~10kHz的频率范围内,该结构水听器的平均声压灵敏度为-132.6dB,波动幅度不大于±0.5dB,加速度灵敏度小于-28dB.该水听器在保证了较高声压灵敏度与平坦的响应曲线的同时,抗加速度性能也得了有效改善,可大大提高光纤激光水听器阵列在运动状态下对远距离目标探测的信噪比.     

20 Hz~10 kHz光纤水听器相移灵敏度校准

利用相位生成载波解调技术精确测量光纤水听器的光相移量,在20 Hz~10 kHz频率范围实现了光纤水听器探头相移灵敏度的校准.20 Hz~1.25 kHz频段采用驻波管比较法进行校准,1.25 kHz~10 kHz频段采用自由场脉冲比较法进行校准.利用本文建立的校准系统,对TMD 35#光纤水听器的相移灵敏度进行校准,校准结果表明,两种方法测得的相移灵敏度具有很好的一致性,在1.25 kHz频率点的相移灵敏度值偏差为0.8 dB.不确定度分析表明,该校准系统的扩展不确定度(k=2)为0.9 dB.     

光纤Bragg光栅水听器特性及实验研究

论述了光纤Bragg光栅（FBG）水听器探头基元 （FBG）的传感特性,分析了FBG的耦合系数、反射率、反射带宽和栅长对光纤Bragg光栅水听器传感特性的影响.通过改进光纤Bragg光栅水听器探头封装结构,增加了其压力敏感系数.并将实验结果与标准水听器（压电型）比较,标定出光纤Bragg光栅水听器的声压灵敏度;对传感信号进行电路解调,得出了解调结果,结果显示与原始声波信号基本一致.试验表明,在1 kHz~25 kHz的声波检测范围,光纤Bragg光栅水听器响应平坦度好,信号输出稳定,证明文中采取的改进措施是有效的.     

干涉型光纤水听器伪工作点控制检测方法

提出了一种用于干涉型光纤水听器信号检测的伪工作点控制方法.为了验证该方法的可行性,搭建了干涉型光纤水听器声压灵敏度测量系统,编写了实时信号采集和处理程序,对某一光纤水听器进行了测量.在频带20 Hz~2.5 kHz上,该光纤水听器的声压灵敏度为－156.5 dB(0 dB=1 rad/μPa),频响波动<±0.8 dB,与采用PGC调制解调方法测量的结果基本一致.由于传感部分不含有源器件,该方法实现了无源检测.另外,它还具有解调算法简单、检测频带宽等优点.     

Mobile adaptive holographic laser hydrophone

A mobile adaptive holographic laser hydrophone based on a dynamic hologram formed in a photorefractive crystal is developed. The hydrophone sensitivity is to –163 dB (rel. 1V/μPa) or 8.6 · 10^?3 rad/Pa in the frequency range of 1–15 kHz. Field tests of the hydrophone were performed in water area of a sea bay. The results confirm the efficiency of the use of measuring systems based on adaptive holographic interferometers to solve problems of recording weak signals (acoustic, hydroacoustic, and others) under non-laboratory conditions.     

夹层式光纤激光水听器探头优化设计

为改善分布反馈式(DFB)光纤激光器水声探测性能,利用有限元软件ANSYS,以相对加速度灵敏度为目标函数,结构尺寸参数为设计变量,结构第一阶固有频率和探头声压灵敏度为状态变量,对夹层式封装结构进行了优化设计,对其声压探测及抗加速度机理进行了分析。分析表明,基于优化结果设计的探头在采用100m非平衡干涉仪时,其声压灵敏度约为-135.1dB,相对加速度灵敏度可达到-19.6dB。结果表明,基于封装结构敏感部分分别承受声压激励和加速度激励时的不同响应机理,对夹层式封装结构关键部位尺寸进行优化设计后,通过合理选择承压梁与中间变形梁的厚度以及上下连接点的位置,封装制得的光纤激光水听器具有较高的声压灵敏度和良好的抗加速度性能。