Morphologies of star-block copolymers in dilute solutions

The morphologies of star-block copolymer (AB)n and (BA)n in a selective solvent for A-block are investigated by using dissipative particle dynamics. For a star-block copolymer of (BA)n type with a large enough arm number n, since the solvophobic B-blocks are situated in the inner part of the star, it behaves as a unimolecular micelle with the B-block core and A-block hairy corona. These types of star copolymers repel each other, thus it is quite difficult to form multimolecular micelles. On the other hand, for a star-block copolymer of (AB)n type, a few aggregative domains develop on the outer rim of the molecule. As the length of B-blocks or the repulsive interaction between B-blocks and solvents is increased, the tendency of B-blocks to associate within the star increases and thus the average number of aggregative domains declines. Owing to the exposure of B-domains, (AB)n type star-blocks tend to form micelles with morphology different from typical micelles. Upon performing simulations for solutions with multiple stars, we have shown that the single molecular conformation may greatly affect the resulting morphology of the supramolecular structure, such as connected-star aggregate, multicore micelle, segmented worm, and core-lump micelle.     

Dissipative Particle Dynamics Simulation of Onion Phase in Star-block Copolymer

A dissipative particle dynamics simulation technique was used to investigate the effect of molecular architecture of star-block copolymer on the patterned structure in a nanodroplet. With increasing the ratio of solvophilic to block length to solvophobic block length(R_H/T), solvophobic sphere, ordered hexagonal phase, onion phase, perforated onion phase and flocculent phase are formed, respectively. Since onion phase has potential application in controlled drug release, it has received wide attention experimentally and theoretically. Our simulation indicates onion phase forms at a certain R_H/T(close to but less than 1). A star-block copolymer molecule has two conformations in onion phase: either fully located in a shell or shared by two neighboring shells. Central structure affects onion's final shape. The molecular number of the copolymer in each shell is a quadratic function of the shell's radius. The arm number of star-block copolymer has little influence on onion's structure, but slightly affects the solvent content. Additionally, we studied the influence of arm length on onion's structure.     

嵌段共聚物微胶束行为的研究Ⅲ．动态激光光散射法研究聚（苯乙烯－异戊二烯）星形嵌段共聚物在选择性溶剂中微胶束的形成过程

采用动态激光光散射研究聚（苯乙烯－异成二烯）（ＰＳ—ＰＩ）星形嵌段共聚物在选择性溶剂二氧六环／甲醇混合体系中微胶束的形成过程。讨论了温度、混合溶剂的组成、星形嵌段共聚物的臂数及组成对微胶束形成的影响。验证了临界接触浓度的存在。并就不同结构的星形嵌段共聚物形成微胶束的形成进行了讨论。     

pH-responsive non-surface-active/surface-active transition of weakly ionic amphiphilic diblock copolymers

The weakly ionic amphiphilic diblock copolymer polystyrene-b-poly(acrylic acid) was synthesized by nitroxy radical-mediated living radical polymerization with precise control of block length, block ratio, and polydispersity. Systematical surface tension experiments and foam formation observations revealed that this polymer was non-surface active under neutral and alkaline (pH 10) conditions, while it was surface active under an acidic condition (pH 3). This result supports our proposed origin of non-surface activity; the image charge repulsion at the air/water interface is essential in addition to very stable micelle formation in the bulk solution. At a higher pH (pH 12), the polymer showed slight surface activity since the added NaOH played a role as an added salt. The critical micelle concentration (cmc) was estimated by static light scattering. Cmc increased with increasing added salt (NaCl) concentration as was observed for other strongly ionic non-surface-active polymers. Hence, this trend is characteristic for non-surface-active polymers. The pH dependence of cmc was minimum at pH 8–10. Since the acrylic acid block is fully ionized under this condition, the strong image charge repulsion at this condition accelerated micelle formation at a low polymer concentration, which consequently decreased cmc. Micelles in bulk solution were confirmed by dynamic light scattering, and the salt concentration and pH dependencies of the hydrodynamic radius of the micelles were also estimated. The pH-responsive non-surface-active/surface-active transition observed in this study strongly supports the fact that the image charge repulsion is an essential factor for non-surface activity in addition to stable micelle formation in solution.     

Block copolymers of ethylene oxide and phenyl glycidyl ether: micellization, gelation, and drug solubilization

Three triblock copolymers of ethylene oxide and phenyl glycidyl ether, type E(m)G(n)E(m), where G = OCH2CH(CH2OC6H5) and E = OCH2CH2, were synthesized and characterized by gel-permeation chromatography, matrix-assisted laser desorption ionization time-of-flight mass spectrometry, and NMR spectroscopy. Their association properties in aqueous solution were investigated by surface tensiometry and light scattering, yielding values of the critical micelle concentration (cmc), the hydrodynamic radius, and the association number. Gel boundaries in concentrated micellar solution were investigated by tube inversion, and for one copolymer, the temperature and frequency dependence of the dynamic moduli served to confirm and extend the phase diagram and to highlight gel properties. Small-angle X-ray scattering was used to investigate gel structure. The overall aim of the work was to define a block copolymer micellar system with better solubilization capacity for poorly soluble aromatic drugs than had been achieved so far by use of block copoly(oxyalkylene)s. Judged by the solubilization of griseofulvin in aqueous solutions of the E(m)G(n)E(m) copolymers, this aim was achieved.     

Synthesis,characterization, and solution behavior of well-defined double hydrophilic linear amphiphilic poly (N-isopropylacrylamide)-b-poly (ε-caprolactone)-b-poly (N-isopropylacrylamide) triblock copolymers

Well-defined linear dihydrophilic amphiphilic ABA-type triblock copolymers of ε-caprolactone (CL) and N-isopropylacrylamide (NIPAAm) have successfully been synthesized with a high yield by combining the ring opening polymerization (ROP) and xanthate-mediated reversible addition-fragmentation chain transfer (RAFT) polymerization methods. The resulted block copolymer shows the formation of micelles in water as supported by light scattering. The critical micelle concentration (cmc) value of the micelle increases with the increase in the chain length of the poly (N-isopropylacrylamide) (PNIPAAm) block. Cloud point of the block copolymers decreases with the decrease in the PNIPAAm chain length. The TGA analysis shows a one-step degradation and a lower thermal stability of the triblock copolymer than the PNIPAAm. The DSC analysis of the triblock copolymer shows the lowering of glass transition temperature (T _g), and melting temperature (T _m) peaks possibly due to the partial miscibility of the poly (ε-caprolactone) (PCL) block with the amorphous PNIPAAm block through the interaction of ester groups of PCL with the amide groups of PNIPAAm. The XRD pattern of the triblock copolymer shows a broad peak due to the suppression of the crystallization of PCL block owing to the mixing of PNIPAAm block with the PCL block.     

Synthesis of four‐armed poly(ε‐caprolactone)‐block‐poly(ethylene oxide) by diethylzinc catalyst

Biodegradable, amphiphilic, four‐armed poly(?‐caprolactone)‐block‐poly(ethylene oxide) (PCL‐b‐PEO) copolymers were synthesized by ring‐opening polymerization of ethylene oxide in the presence of four‐armed poly(?‐caprolactone) (PCL) with terminal OH groups with diethylzinc (ZnEt₂) as a catalyst. The chemical structure of PCL‐b‐PEO copolymer was confirmed by ¹H NMR and ¹³C NMR. The hydroxyl end groups of the four‐armed PCL were successfully substituted by PEO blocks in the copolymer. The monomodal profile of molecular weight distribution by gel permeation chromatography provided further evidence for the four‐armed architecture of the copolymer. Physicochemical properties of the four‐armed block copolymers differed from their starting four‐armed PCL precursor. The melting points were between those of PCL precursor and linear poly(ethylene glycol). The length of the outer PEO blocks exhibited an obvious effect on the crystallizability of the block copolymer. The degree of swelling of the four‐armed block copolymer increased with PEO length and PEO content. The micelle formation of the four‐armed block copolymer was examined by a fluorescent probe technique, and the existence of the critical micelle concentration (cmc) confirmed the amphiphilic nature of the resulting copolymer. The cmc value increased with increasing PEO length. The absolute cmc values were higher than those for linear amphiphilic block copolymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 950–959, 2004     

Synthesis and surface properties of semi-fluorinated gemini surfactants with two reactive bromo pendant groups

This paper presents a series of semi-fluorinated gemini surfactants with two bromo pendant groups. It reviews the effect of the number of methylene units in the spacer group between the two hydrophilic quaternary ammonium heads. Critical micelle concentration (cmc) and free energy of micellization (ΔG(M)(0)) of the title surfactants, in aqueous solution, have been investigated as a function of the number n of carbon atoms in the hydrocarbon spacer. We have pointed out a different behaviour as compared to Gemini hydrocarbon homologues. In the present study, when the number of methylene units (n) in the spacer increases, the cmc first decreases and reaches an optimum for (n=6), then it increases linearly from n≥6. Variations of cmc have been interpreted in terms of conformation changes of the surfactant ion and progressive penetration of the alkyl chain spacer in the micelle hydrophobic core. In this series, the increase of the hydrophobicity seems not to favour the micellisation process as expected, probably impacted by the mutual phobicity of the perfluorinated tails and the hydrocarbon spacer. A minimum is reached for a spacer with six methylene units which seems to be the optimal conformation. The free energy of micellization (ΔG(M)(0)) confirm this tendency.     

Micellisation of triblock copolymers of ethylene oxide and 1,2-butylene oxide: effect of B-block length

We have used pyrene fluorescence spectroscopy and isothermal titration calorimetry (ITC) to investigate the effect of hydrophobic-block length on values of the critical micelle concentration (cmc) for aqueous solutions of triblock poly(butylene oxide)-poly(ethylene oxide)-poly(butylene oxide) block copolymers (B(n)E(m)B(n), where m and n denote the respective block lengths) with hydrophobic block lengths in the range n=12-21. Combined with results from previous work on B(n)E(m)B(n) copolymers with shorter B blocks, plots of log(10)(cmc) (cmc in molar units and reduced to a common E-block length) against total number of B units (n(t)=n for diblock or n(t)=2n for triblock copolymers) display transitions in the slopes of the two plots, which indicate changes in the micellisation equilibrium. These occur at values of n(t)which can be assigned to the onset and completion of collapse of the hydrophobic B blocks, an effect not previously observed for reverse triblock copolymers. The results are compared with related data for diblock E(m)B(n) copolymers.     

Non-surface activity and micellization behavior of cationic amphiphilic block copolymer synthesized by reversible addition-fragmentation chain transfer process

Cationic amphiphilic diblock copolymers of poly(n-butylacrylate)-b-poly(3-(methacryloylamino)propyl)trimethylammonium chloride) (PBA-b-PMAPTAC) with various hydrophobic and hydrophilic chain lengths were synthesized by a reversible addition-fragmentation chain transfer (RAFT) process. Their molecular characteristics such as surface activity/nonactivity were investigated by surface tension measurements and foam formation observation. Their micelle formation behavior and micelle structure were investigated by fluorescence probe technique, static and dynamic light scattering (SLS and DLS), etc., as a function of hydrophilic and hydrophobic chain lengths. The block copolymers were found to be non-surface active because the surface tension of the aqueous solutions did not change with increasing polymer concentration. Critical micelle concentration (cmc) of the polymers could be determined by fluorescence and SLS measurements, which means that these polymers form micelles in bulk solution, although they were non-surface active. Above the cmc, the large blue shift of the emission maximum of N-phenyl-1-naphthylamine (NPN) probe and the low micropolarity value of the pyrene probe in polymer solution indicate the core of the micelle is nonpolar in nature. Also, the high value of the relative intensity of the NPN probe and the fluorescence anisotropy of the 1,6-diphenyl-1,3,5-hexatriene (DPH) probe indicated that the core of the micelle is highly viscous in nature. DLS was used to measure the average hydrodynamic radii and size distribution of the copolymer micelles. The copolymer with the longest PBA block had the poorest water solubility and consequently formed micelles with larger size while having a lower cmc. The "non-surface activity" was confirmed for cationic amphiphilic diblock copolymers in addition to anionic ones studied previously, indicating the universality of non-surface activity nature.     

温敏性含氟两亲接枝共聚物的制备及胶束化行为

以聚乙二醇单甲醚甲基丙烯酸酯(MPEGMA)为大分子单体, 甲基丙烯酸六氟丁酯(HFMA)为含氟单体, N-异丙基丙烯酰胺(NIPAAm)为功能性单体, 采用大分子单体接枝共聚法, 制备了一种温敏性含氟两亲接枝共聚物P(NIPAAm-co-HFMA)-g-PEG. 利用FTIR, ¹H NMR, ¹⁹F NMR和GPC对共聚物的结构进行表征; 采用紫外-可见分光光度计测定了共聚物的低临界溶解温度(LCST)约为38.9 ℃, 高于人体正常的生理温度; 利用荧光探针技术测定了共聚物的临界胶束浓度(cmc), 结果表明, 当共聚物溶液温度高于LCST时, 其cmc明显变小; 利用激光光散射粒度仪(LLS)测定了共聚物胶束的水合粒径及其分布, 当温度达到LCST时, 胶束粒径明显变小, 温度过高时, 粒径又有所增大; 利用透射电子显微镜(TEM)研究了共聚物胶束的形貌, 结果表明, P(NIPAAm-co-HFMA)-g-PEG在水溶液中可自组装成球状胶束粒子, 随着温度的升高, 共聚物胶束由松散的核壳结构转变成更加紧凑的球状结构, 且粒径明显变小.     

Non-surface activity and micellization of ionic amphiphilic diblock copolymers in water. Hydrophobic chain length dependence and salt effect on surface activity and the critical micelle concentration

We reported previously (Macromolecules 2003, 36, 5321; Langmuir, 2004, 20, 7412) that amphiphilic diblock copolymers having polyelectrolytes as a hydrophilic segment show almost no surface activity but form micelles in water. In this study, to further investigate this curious and novel phenomenon in surface and interface science, we synthesized another water-soluble ionic amphiphilic diblock copolymer poly(hydrogenated isoprene)-b-sodium poly(styrenesulfonate) PIp-h2-b-PSSNa by living anionic polymerization. Several diblock copolymers with different hydrophobic chain lengths were synthesized and the adsorption behavior at the air/water interface was investigated using surface tension measurement and X-ray reflectivity. A dye-solubilization experiment was carried out to detect the micelle formation. We found that the polymers used in this study also formed micelles above a certain polymer concentration (cmc) without adsorption at the air-water interface under a no-salt condition. Hence, we further confirmed that this phenomenon is universal for amphiphilic ionic block copolymer although it is hard to believe from current surface and interface science. For polymers with long hydrophobic chains (more than three times in length to hydrophilic chain), and at a high salt concentration, a slight adsorption of polymer was observed at the air-water interface. Long hydrophobic chain polymers showed behavior "normal" for low molecular weight ionic surfactants with increasing salt concentration. Hence, the origin of this curious phenomenon might be the macroionic nature of the hydrophilic part. Dynamic light scattering analysis revealed that the hydrodynamic radius of the block copolymer micelle was not largely affected by the addition of salt. The hydrophobic chain length-cmc relationship was found to be unusual; some kind of transition point was found. Furthermore, very interestingly, the cmc of the block copolymer did not decrease with the increase in salt concentration, which is in clear contrast to the fact that cmc of usual ionic small surfactants decreases with increasing salt concentration (Corrin-Harkins law). These behaviors are thought to be the special, but universal, characteristics of ionic amphiphilic diblock copolymers, and the key factor is thought to be a balance between the repulsive force from the water surface by the image charge effect and the hydrophobic adsorption.     

Aggregation Number of Ionic Surfactants and its Application for Alkyltrimethyl Ammonium Bromides and Sodium Tetradecyl Sulfate by Potentiometric Technique

A potentiometric technique based on surfactant ion selective electrode has been used for various cationic and anionic surfactants. The data obtained contain m ₁ (surfactant monomer concentration); m ₂ (free counterion concentration) and α (degree of dissociation of micelle) were used for determination of aggregation number at and above cmc (critical micelle concentration). Data fitting show a relationship between aggregation number with such parameters. The correlation equation obtained shows that size of ionic micelle vary sharply after cmc. Also, the equation obtained shows size of micelle growth with increase in counterion concentration.     

Micelle formation by N-alkyl-N-methylpyrrolidinium bromide in aqueous solution

The micellization of the ionic liquid N-alkyl-N-methylpyrrolidinium bromide (C(n)MPB, n = 12, 14 and 16) in aqueous solutions was investigated by surface tension measurements, electrical conductivity and static luminescence quenching. The effectiveness of the surface tension reduction (Π(cmc)), maximum surface excess concentration (Γ(max)) and the minimum area (A(min)) occupied per surfactant molecule at the air/water interface can be obtained from the surface tension measurements at 25 °C. The critical micelle concentration (cmc) at different temperatures and a series of thermodynamic parameters (ΔG, ΔH and ΔS) of micellization were evaluated from electrical conductivity measurements in the temperature range of 25-45 °C. The thermodynamic parameters show that the micelle formation is entropy-driven at low temperature and enthalpy-driven at high temperature. Furthermore, the micelle aggregation number (N(agg)) of C(n)MPB was calculated according to the Turro-Yekta method through static luminescence quenching and found that N(agg) (49, 55, and 59) increased with the hydrophobic chain length of C(n)MPB.     

Probing the micellization of diblock and triblock copolymers of poly(<Emphasis Type="SmallCaps">l</Emphasis>-lactide) and poly(ethylene glycol) in aqueous and NaCl salt solutions

The micelle formation of a series of amphiphilic block copolymers in aqueous and NaCl solutions was studied by a fluorescent probe technique using pyrene as a "model drug". These copolymers were synthesized from poly (ethylene glycol) (PEG) and l-lactide by a new calcium ammoniate catalyst. They had fixed PEG block lengths (44, 104 or 113 ethylene oxide units) and various poly(l-lactide) (PLLA) block lengths (15–280 lactide units). The critical micelle concentration (cmc) was found to decrease with increasing PLLA content. The distinct dissimilarity of the cmc values of diblock and triblock copolymers based on the same block length of PEG provided evidence for the different configurations of their micelles. It was also observed that the introduction of NaCl salt significantly contributed to a decrease in the cmcs of the copolymers with short PEG and PLLA blocks, while it had less influence on the cmcs of copolymers with long PEG or PLLA blocks. The dependence of partition coefficients ranging from 0.2×10⁵ to 1.9×10⁵ on the PLLA content in the copolymer and on the micelle configuration was also discussed. The contribution of NaCl salt to increasing the partition of pyrene into a micellar phase was observed.     

Mechanism of gold metal ion reduction, nanoparticle growth and size control in aqueous amphiphilic block copolymer solutions at ambient conditions

Spontaneous formation and efficient stabilization of gold nanoparticles with an average diameter of 7 approximately 20 nm from hydrogen tetrachloroaureate(III) hydrate (HAuCl4.3H2O) were achieved in air-saturated aqueous poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) block copolymer solutions at ambient temperature in the absence of any other reducing agent. The particle formation mechanism is considered here on the basis of the block copolymer concentration dependence of absorption spectra, the time dependence (kinetics) of AuCl4- reduction, and the block copolymer concentration dependence of particle size. The effects of block copolymer characteristics such as molecular weight (MW), PEO block length, PPO block length, and critical micelle concentration (cmc) are explored by examining several PEO-PPO-PEO block copolymers. Our observations suggest that the formation of gold nanoparticles from AuCl4- comprises three main steps: (1) reduction of metal ions by block copolymer in solution, (2) absorption of block copolymer on gold clusters and reduction of metal ions on the surface of these gold clusters, and (3) growth of metal particles stabilized by block copolymers. While both PEO and PPO blocks contribute to the AuCl4- reduction (step 1), the PEO contribution appears to be dominant. In step 2, the adsorption of block copolymers on the surface of gold clusters takes place because of the amphiphilic character of the block copolymer (hydrophobicity of PPO). The much higher efficiency of particle formation attained in the PEO-PPO-PEO block copolymer systems as compared to PEO homopolymer systems can be attributed to the adsorption and growth processes (steps 2 and 3) facilitated by the block copolymers. The size of the gold nanoparticles produced is dictated by the above mechanism; the size increases with increasing reaction activity induced by the block copolymer overall molecular weight and is limited by adsorption due to the amphiphilic character of the block copolymers.     

Interactions between 12-EOx-12 gemini surfactants and pluronic ABA block copolymers (F108 and P103) studied by isothermal titration calorimetry

The interactions between triblock copolymers of poly(ethylene oxide) and poly(propylene oxide), P103 and F108, EO(n)PO(m)EO(n), m = 56 and n = 17 and 132, respectively, and gemini surfactants (oligooxa)-alkanediyl-alpha,omega-bis(dimethyldodecylammonium bromide) (12-EO(x)-12), x = 0-3, have been studied in aqueous solution using isothermal titration calorimetry. The thermograms of F108 as a function of surfactant concentration show one broad peak at polymer concentrations, Cp, < or =0.50 wt %, below the critical micelle concentration (cmc) of the copolymer at 25 degrees C. It is attributed to interactions between the surfactant and the triblock copolymer monomer. The critical aggregation concentration (cac) remains constant while deltaHmax2 and the saturation concentration, C2, increase with increasing copolymer concentration. Analysis of the cac data offers semiquantitative support that the degree of ionization of the surfactant aggregates bound to polymers is likely to be larger than that at the surfactant cmc. In P103 solutions at Cp > or = 0.05 wt %, two peaks appear in the thermograms and they are attributed to the interactions between the gemini surfactant and the micelle or monomeric forms of the copolymer. An origin-based nonlinear fitting program was employed to deconvolute the two peaks and to obtain estimates of peak properties. An estimate of the fraction of copolymer in aggregated form was also obtained. The enthalpy change due to interactions between the surfactants and P103 aggregates is very large compared to values obtained for traditional surfactants. This suggests that extensive reorganization of copolymer aggregates and surrounding solvent occurs during the interaction. Dehydration of the copolymers by the surfactant may also play an important step in the interaction. The endothermic enthalpy change reflecting interactions between the surfactant and polymer decreases more rapidly as the length and hydrophilic character of the spacer increases, suggesting that more favorable interactions occur with the P103 monomers having shorter PEO segments.