180–425 GHz low noise SIS waveguide receivers employing tuned Nb/AIOx/Nb tunnel junctions

We report recent results on a 20% reduced height 270–425 GHz SIS waveguide receiver employing a 0.49 µm² Nb/AlO _x /Nb tunnel junction. A 50% operating bandwidth is achieved by using a RF compensated junction mounted in a two-tuner reduced height waveguide mixer block. The junction uses an end-loaded tuning stub with two quarter-wave transformer sections. We demonstrate that the receiver can be tuned to give 0–2 dB of conversion gain and 50–80% quantum efficiency over parts of it's operating range. The measured instantaneous bandwidth of the receiver is 25 GHz which ensures virtually perfect double sideband mixer response. Best noise temperatures are typically obtained with a mixer conversion loss of 0.5 to 1.5 dB giving uncorrected receiver and mixer noise temperatures of 50K and 42K respectively at 300 and 400 GHz. The measured double sideband receiver noise temperature is less than 100K from 270 GHz to 425 GHz with a best value of 48K at 376 GHz, within a factor of five of the quantum limit. The 270–425 GHz receiver has a full 1 GHz IF passband and has been successfully installed at the Caltech Submillimeter Observatory in Hawaii. Preliminary tests of a similar junction design in a full height 230 GHz mixer block indicate large conversion gain and receiver noise temperatures below 50K DSB from 200–300 GHz. Best operation is again achieved with the mixer tuned for 0.5–1.5 dB conversion loss which at 258 GHz resulted in receiver and mixer noise temperature of 34K and 27K respectively.     

A Low-Noise 230 GHz SIS Receiver for Radio Astronomy Employing Untuned Nb/AlOx/Nb Tunnel Junctions

A heterodyne receiver based on a 1/3 reduced height rectangular waveguide SIS mixer with two mechanical tuners has been built for astronomical observations of molecular transitions in the 230 GHz frequency band. The mixer used an untuned array (R_nC_j3, R_n70 ) of four Nb/AIOx/Nb tunnel junctions in series as a nonlinear mixing element. A reasonable balance between the input and output coupling efficiencies has been obtained by choosing the junction number N=4. The receiver exhibits DSB (Double Side Band) noise temperature around 50 K over a frequency range of more than 10 GHz centered at 230 GHz. The lowest system noise temperature of 38 K has been recorded at 232.5 GHz. Mainly by adjusting the subwaveguide backshort, the SSB (Single Side Band) operation with image rejection of 15 dB is obtained with the noise temperature as low as 50 K. In addition, the noise contribution from each receiver component has been studied further. The minimum SIS mixer noise temperature is estimated as 15 K, pretty close to the quantum limit v/k11 K at 230 GHz. It is believed that the receiver noise temperatures presented are the lowest yet reported for a 230 GHz receiver using untuned junctions.     

A lownoise 665 GHz SIS quasi-particle waveguide receiver

We report recent results on a 565–690 GHz SIS heterodyne receiver employing a 0.36µm² Nb/AlO _x /Nb SIS tunnel junction with high quality circular non-contacting backshort and E-plane tuners in a full height waveguide mount. No resonant tuning structures have been incorporated in the junction design at this time, even though such structures are expected to help the performance of the receiver. The receiver operates to at least the gap frequency of Niobium, 680 GHz. Typical receiver noise temperatures from 565–690 GHz range from 160K to 230K with a best value of 185K DSB at 648 GHz. With the mixer cooled from 4.3K to 2K the measured receiver noise temperatures decreased by approximately 15%, giving roughly 180K DSB from 660 to 680 GHz. The receiver has a full 1 GHz IF passband and has been successfully installed at the Caltech Submillimeter Observatory in Hawaii.     

A low-noise SIS receiver measured from 480 GHz to 650 GHz using Nb junctions with integrated RF tuning circuits

A heterodyne receiver using an SIS waveguide mixer with two mechanical tuners has been characterized from 480 GHz to 650 GHz. The mixer uses either a single 0.5 × 0.5 µm² Nb/AlO_x/Nb SIS tunnel junction or a series array of two 1 µm² Nb tunnel junctions. These junctions have a high current density, in the range 8 – 13 kA/cm². Superconductive RF circuits are employed to tune the junction capacitance. DSB receiver noise temperatures as low as 200 ± 17 K at 540 GHz, 271 K ± 22 K at 572 GHz and 362 ± 33 K at 626 GHz have been obtained with the single SIS junctions. The series arrays gave DSB receiver noise temperatures as low as 328 ± 26 K at 490 GHz and 336 ± 25 K at 545 GHz. A comparison of the performances of series arrays and single junctions is presented. In addition, negative differential resistance has been observed in the DC I–V curve near 490, 545 and 570 GHz. Correlations between the frequencies for minimum noise temperature, negative differential resistance, and tuning circuit resonances are found. A detailed model to calculate the properties of the tuning circuits is discussed, and the junction capacitance as well as the London penetration depth of niobium are determined by fitting the model to the measured circuit resonances.     

Wide-band low noise MM-wave SIS mixers with a single tuning element

Several SIS quasiparticle mixers have been designed and tested for the frequency range from 80 to 115 GHz. The sliding backshort is the only adjustable RF tuning element. The RF filter reactance is used as a fixed RF matching element. A mixer which uses a single 2×2 m² Pb-alloy junction in a quarter-height waveguide mount has a coupled conversion gain of G_M(DSB)=2.6±0.5 dB with an associated noise temperature of T_M(DSB)=16.4±1.8 K at the best DSB operation point. The receiver noise temperature T_R(DSB) is 27.5±0.8 K for the mixer test apparatus. This mixer provides a SSB receiver noise temperature below 50 K over the frequency range from 91 to 96 GHz, the minimum being T_R(SSB)=44±4 K. Another mixer with an array of five 5×5 m² junctions in series in a full-height wave-guide mount has much lower noise temperature T_M(DSB)=6.6±1.6 K, but less gain G_M(DSB)=–5.1±0.5 dB.Contribution of the U.S. Government, not subject to copyright     

Low noise submillimeter SIS receiver with niobium nitride quasiparticle tunnel junctions

We have developed and tested a submillimeter waveguide SIS mixer with NbN-MgO-NbN quasiparticle tunnel junctions. The two junction array is integrated in a full NbN printed circuit. The NbN film critical temperature is 15 K and the junction gap voltage is 5 mV. The size of the junctions is 1.4 × 1.4 µm and Josephson critical current density is about 1.5 KA/cm² resulting in junction R_NC product about 40. The inductive tuning circuit in NbN is integrated with each junction in two junction array. A single non contacting backshort was tuned at each frequency in the mixer block.At 306 GHz the minimum DSB receiver noise temperature is as low as 230 K. The sources of the receiver noise and of the limits of the NbN SIS submillimeter mixer improvement are discussed.     

Some recent developments in the design of SIS mixers

SIS mixers in which superconducting tuning elements are integrated with the tunnel junctions have resulted in very low noise heterodyne receivers in the range 68–260 GHz. Above 120 GHz the need for extremely small reduced-height waveguides is avoided by mounting the SIS junctions in a suspended-stripline circuit coupled to a full-height waveguide by a broadband probe. The special characteristics of coplanar transmission line permit the design of SIS mixers with low parasitic reactances. Such a mixer operates over the full WR-10 band (75–110 GHz) without mechanical tuners.An earlier version of this paper was presented at the First International Symposium on Space THz Technology, March, 1990.The National Radio Astronomy Observatory is operated by Associated Universities, Inc., under cooperative agreement with the National Science Foundation.     

A 350GHz Radial-Probe SIS Mixer for Astronomical Imaging Arrays

We have developed a 330-370GHz SIS mixer for small-format, heterodyne, astronomical imaging arrays. Fixed-tuned broadband operation is achieved by means of a superconducting radial waveguide probe. A horn-reflector antenna provides high-efficiency optical coupling. Using a variable-temperature cryogenic noise source, we measured a DSB system noise temperature of 32±1K. The mixer contributes 3±3K, supporting the theoretically-predicted result that the noise temperature of a DSB mixer can be less than h/2 (8.6K)     

A 210–280 GHz sis heterodyne receiver for the James Clerk Maxwell Telescope part I: Design and performance

We describe the design and performance of a 210–280 GHz SIS heterodyne receiver built for use on the Maxwell Telescope. The mixer utilises a lead alloy SIS tunnel junction, mounted in 41 reduced height rectangular waveguide, and is tuned with a backshort in 21 reduced height guide. The receiver has a receiver noise temperature of <200K (DSB) across the RF band from 210–270 GHz, with a best noise temperature measured in the laboratory of 113K (DSB) at 231 GHz. A prototype version of this receiver was successfully operated on the telescope in May 1989. By direct intercalibration with a Schottky diode receiver we deduced a best receiver noise temperature of 140K (DSB) at 245 GHz. Discrepancies between this figure and that derived from broad band thermal load calibration are discussed in the accompanying paper (Little et al., 1992, this issue).     

Simple 1 MM Receivers with a Fixed Tuned Double Sideband SIS Mixer and a Wideband INP MMIC Amplifier

We report on techniques to broaden the intermediate frequency (IF) bandwidth of the BerkeleyIllinoisMaryland Array (BIMA) 1mm SuperconductorInsulatorSuperconductor (SIS) heterodyne receivers by combining fixed tuned Double Side Band (DSB) SIS mixers and wideband Monolithic Microwave Integrated Circuit (MMIC) IF amplifiers. To obtain the flattest receiver gain across the IF band we tested three schemes for keeping the mixer and amplifier as electrically close as possible. In Receiver I, we connected separate mixer and MMIC modules by a 1 stainless steel SMA elbow. In Receiver II, we integrated mixer and MMIC into a modified BIMA mixer module. In Receiver III, we devised a thermally split block in which mixer and MMIC can be maintained at different temperatures–in this receiver module the mixer at 4 K sees very little of the 10–20 mW heat load of the biased MMIC at 10 K. The best average receiver noise we achieved by combining SIS mixer and MMIC amplifier is 45 50 K DSB for _LO = 215–240 GHz and below 80 K DSB for _LO = 205 270 GHz. Over an IF frequency band of 1 – 4 GHz we have demonstrated receiver DSB noise temperatures of 40 – 60 K. Of the three receiver schemes, we feel Receiver III shows the most promise for continued development.     

A superconducting tunnel junction receiver for 345 GHz

In this paper we discuss the design, fabrication, and testing of a quasiparticle tunnel junction receiver for use at 345 GHz. The design employs small area Nb/Nb-oxide/PbInAu edge junctions in order to keep the device capacitance small and maintain a modest value for R_NC. For optimura noise performance and beam properties the mixer is contained in a waveguide mounting structure. Our best sensitivity was obtained at 312 GHz where we measured a double sideband (DSB) noise temperature of 275 K. Noise temperatures of 400 K (DSB) or better were obtained out to 350 GHz.     

Low noise 80–115 GHz quasiparticle mixer with small Nb/Al-Oxide/Nb tunnel junctions

Millimeter-wave characterization of a heterodyne receiver using (2 m²) Nb/Al-Ox/Nb Superconducting-Insulator-Superconducting (SIS) junctions arrays is reported. The fabrication of the Nb/Al-Ox/Nb SIS junction arrays as a heterodyne mixer is described. The leakage current of these junctions is below 2A at 4.2K and unmeasurable at 2.5K. The receiver gave a noise temperature Double Side Band (DSB) between 63K and 187K over the frequency range 80 to 115 GHz at the first conversion peak. The results are comparable to those obtained with SIS receivers using well researched lead junctions. Contrary to the lead junctions, our mixer using all Nb junctions have proven remarkably stable with respect to thermal cycling, characteristics which are required for space applications. To our knowledge, this is the most reliable low noise receiver operating in this frequency range.     

Effect of an applied magnetic field on the performance of a sis receiver near 300 GHz

We have successfully constructed and tested a superconductor-insulator-superconductor (SIS) receiver for operation at 265–280 GHz using 1 m² area Nb–AlO _x –Nb tunnel junctions fabricated at Stony Brook. The best performance to date is a double sideband (DSB) receiver noise temperature of 129 K at 278 GHz. We find that suppression of the Josephson pair currents with a magnetic field is essential for good performance and a stable DC bias point. Fields as high as 280 gauss have been used with no degradation of mixing performance. We illustrate the improvement in the intermediate frequency (IF) output stability with progressively increasing magnetic fields.     

A 275–370 GHz Receiver Employing Novel Probe Structure

We present the results of the development of a 275–370 GHz, fixed-tuned double sideband (DSB) receiver based on superconductor-insulator-superconductor (SIS) junction mixer. The mixer block uses a full height rectangular waveguide and employs a novel radial-like probe structure with integrated bias-T. The measured uncorrected receiver noise temperature is 30–50 K corresponding to about 2–3 quantum noise across the full frequency band with an IF from 3.8 to 7.6 GHz. The mixer is to be used on the Atacama Pathfinder EXperiment (APEX) submillimeter telescope in Chile.     

Design Consideration for a Two-Distributed-Junction Tuning Circuit

We describe a novel method of designing a tuning circuit with two half-wave distributed junctions separated by a half-wavelength microstripline, which analytically determines the circuit parameters such as the minimum current density of the junctions and the characteristic impedances of the distributed junctions and the microstripline. The tuning circuit was approximated by simple transmission theory and then simplified with ideal circuit components for analysis. We applied Chebyshevs band-pass filter theory, in part, to optimize the circuit design. The analytical results revealed that a high characteristic-impedance ratio between the distributed junctions and the microstripline is necessary to obtain broadband matching using low-current-density junctions. The experimental results for all-NbN SIS mixers we designed with this method demonstrated double-sideband (DSB) receiver-noise temperatures of 6–10 quanta from 710 to 810 GHz for a mixer with a current density of only 4 kA/cm² (estimated C_JR_N product of 37 at 750 GHz). The RF bandwidth was broader than that of a conventional full-wave distributed SIS mixer with the same current density.     

A 40 GHz band SIS receiver using Nb/Al?AlOx/Nb array junctions

A 40 GHz band SIS mixer receiver has been built using Nb/Al–AlOx/Nb array junctions and a 4.3 K closed cycle helium refrigerator. The minimum conversion loss of the mixer is 2±1 dB and the single sideband receiver noise temperature (T_RX (SSB)) is as low as 110±10 K at 36 GHz. T_RX (SSB) is almost constant in the IF bandwidth of 600 MHz. The mixer saturation level is as high as 15 nW, which is comparable to the injected LO power.Nobeyama Radio Observatory (NRO), a branch of the Tokyo Astronomical Observatory, University of Tokyo, is a cosmic radio observing facility open for outside users.     

Noise and thermal properties of a submillimeter mixer with the SINS tunnel junction

In this work we present for the first time a low-noise submillimeter receiver with a mixer using Superconductor-Insulator-Normal metal-Superconductor (SINS) junctions. Junctions containing a normal metal layer may be free of the Josephson current and of the related perturbations of mixer operation specific for the standard SIS mixers. This SINS mixer quality is important for the application in the multibeam submillimeter receiver. The SINS mixer stability of operation and independence on the magnetic field have been confirmed in our experiment. Minimum SINS receiver noise in the 290 – 330 GHz band is about 135 K when the junction R_NC is about 30. Noise, conversion gain and thermal properties of the SINS mixer have been studied and compared with the SIS mixers. The limit of SINS mixer operation improvement is discussed at the end of the work.     

High Doping Density Schottky Diodes in the 3MM Wavelength Cryogenic Heterodyne Receiver

The paper describes a 3mm cryogenic mixer receiver using high doping density (“room-temperature”) Schottky diodes. The measured equivalent noise temperature T_eq of the diodes is 109 K at 20 K, which is much higher than the T_eq of the low doping density (“cryogenic”) diodes. In spite of this, the double-sideband (DSB) noise temperature of the cryogenic receiver developed is 55 K at 110 GHz, owing to the low conversion loss of the mixer and ultra-low noise of the PHEMT IF amplifier. This is the lowest noise temperature ever reported for a Schottky diode mixer receiver. The results obtained are useful for the development of submm receivers in which high doping density Schottky diodes are used.