Simultaneous measurement of refractive index and temperature using dual-period grapefruit microstructured fiber grating

By cascading the long period fiber grating (LPFG) and fiber Bragg grating (FBG) in grapefruit microstructured fiber, a novel dual-period fiber grating sensor is proposed. The refractive index and temperature are measured simultaneously by using the different sensitivity of FBG and LPFG. The relationship between dual-period fiber grating transmission spectrum and refractive index, resonant wavelengths and temperature are analyzed theoretically, respectively. The simulation results show that the accuracy of the sensor in measuring refractive index and temperature is estimated to be 2319.6 nm/RIU in a range from 1.33 to 1.36 and 0.017 nm/°C from 0 °C to 100 °C, respectively. Thus, the sensor has high refractive index sensitivity, and can provide the theoretical foundation for the optical fiber biosensor.     

Influence of temperature annealing on optical properties of SrTiO3/BaTiO3 multilayered films on indium tin oxide

We have prepared SrTiO₃/BaTiO₃ thin films with multilayered structures deposited on indium tin oxide (ITO) coated glass by a sol-gel deposition and heating at 300-650 °C. The optical properties were obtained by UV-vis spectroscopy. The films show a high transmittance (approximately 85%) in the visible region. The optical band gap of the films is tunable in the 3.64-4.19 eV range by varying the annealing temperature. An abrupt decrease towards the bulk band gap value is observed at annealing temperatures above 600 °C. The multilayered film annealed at 650 ° C exhibited the maximum refractive index of 2.09-1.91 in the 450-750 nm wavelength range. The XRD and AFM results indicate that the films annealed above 600 ° C are substantially more crystalline than the films prepared at lower temperatures which were used to change their optical band gap and complex refractive index to an extent that depended on the annealing temperature.     

Broadband Er-Yb co-doped superfluorescent fiber source

In this paper, extensive experimental results on broad-band double cladding Er³⁺-Yb³⁺ co-doped superfluorescent fiber sources (SFSs), characterizing their output power, mean wavelength, and bandwidth (BW) stability with variations of pump power, pump wavelength, and fiber temperature, have been reported. For a 55-cm fiber, SFS power from 3.7755 (maximum BW condition of more than 80 nm) to 9.1837 mW (maximum power condition, BW is about 34 nm) has been achieved. The SFS mean wavelength dependence on pump wavelength is highly pump temperature sensitive, and can be reduced to zero in a chosen pump temperature field. The intrinsic variation of the SFS mean wavelength λ_m with fiber temperature is also measured, and a linear variation from 15 to 45 °C with a slop of −0.053 nm/°C for L_f = 100 cm and −0.04 nm/°C for L_f = 55 cm is found.     

The spectral sensitivity of long period gratings fabricated in elliptical core D-shaped optical fibre

Long period gratings (LPGs) were written into a D-shaped optical fibre that has an elliptical core with a W-shaped refractive index profile and the first detailed investigation of such LPGs is presented. The LPGs’ attenuation bands were found to be sensitive to the polarisation of the interrogating light with a spectral separation of about 15 nm between the two orthogonal polarisation states. A finite element method was successfully used to model many of the behavioural features of the LPGs. In addition, two spectrally overlapping attenuation bands corresponding to orthogonal polarisation states were observed; modelling successfully reproduced this spectral feature. The spectral sensitivity of both orthogonal states was experimentally measured with respect to temperature and bending. These LPG devices produced blue and red wavelength shifts depending upon the orientation of the bend with measured maximum sensitivities of −3.56 and +6.51 nm m, suggesting that this type of fibre LPG may be useful as a shape/bend orientation sensor with reduced errors associated with polarisation dependence. The use of neighbouring bands to discriminate between temperature and bending was also demonstrated, leading to an overall curvature error of ±0.14 m⁻¹ and an overall temperature error of ±0.3 °C with a maximum polarisation dependence error of ±8 × 10⁻² m⁻¹ for curvature and ±5 × 10⁻² °C for temperature.     

Effects of depositing temperatures on structure and optical properties of TiO2 film deposited by ion beam assisted electron beam evaporation

TiO₂, which is high in refractive index and dielectric constant, plays an important role in the fields of optics and electronics. In this work, TiO₂ films were prepared on glass substrates by the technique of ion beam assisted electron beam evaporation. The films were deposited at 50, 150 and 300 °C, respectively. Then the as-deposited TiO₂ films were annealed at 450 °C for 1 h in vacuum atmosphere. Structures and optical properties of TiO₂ films were characterized by XRD, SEM, ellipsometry and spectrophotometer. As a result, the structure and the refractive index of films were improved by both the annealing and the increasing of the deposition temperature. The UV-vis transmittance spectra also confirmed that the deposition temperature has a significant effect on the transparency of the thin films. The highest transparency over the visible wavelength region of spectra was obtained at the deposition temperature of 300 °C. The allowed direct band gap at the deposition temperature ranging from 50 to 300 °C was estimated to be in the range from 3.81 to 3.92 eV.     

Estimation of the fibre temperature during the inscription of arc-induced long-period gratings

The underlying formation mechanisms and the properties of long-period gratings produced through arc discharges are intrinsically related to the temperature reached by the fibre during arc exposure. In this work, the determination of the fibre temperature was based on Plank’s blackbody radiation law. The radiation emitted by the optical fibre during heating due to an electric arc discharge, detected using a Cronin spectrometer, was fitted to the emission spectrum of the blackbody radiation, allowing the estimation of the temperature range attained by the fibre. A peak temperature of 1400 ± 50 °C was obtained.     

Influence of substrate temperature on the optical and piezoelectric properties of ZnO thin films deposited by rf magnetron sputtering

In this study, ZnO thin films were fabricated using the rf magnetron sputtering method and their piezoelectrical and optical characteristics were investigated for various substrate temperatures. The ZnO thin film has the largest crystallization orientation for the (0 0 2) peak and the smallest FWHM value of 0.56° at a substrate temperature of 200 °C. The surface morphology shows a relatively dense surface structure at 200 °C compared to the other substrate temperatures. The surface roughness shows the smallest of 1.6 nm at a substrate temperature of 200 °C. The piezoelectric constant of the ZnO thin film measured using the pneumatic loading method (PLM) has a maximum value of 11.9 pC/N at a substrate temperature of 200 °C. The transmittance of the ZnO thin film measured using spectrophotometry with various substrate temperatures ranged from 75 to 93% in the visible light region. By fitting the refractive index from the transmittance to the Sellmeir dispersion relation, we can predict the refractive index of the ZnO thin film according to the wavelength. In the visible light range, the refraction index of the ZnO thin film deposited at a substrate temperature of 200 °C is the range of 1.88-2.08.     

Influence of substrate temperature on properties of MgF2 coatings

Thermal boat evaporation was employed to prepare MgF₂ single-layer coatings upon both JGS1 and UBK7 substrates at different substrate temperatures. Microstructure, transmittance and residual stress of these coatings were measured by X-ray diffraction, spectrophotometer, and optical interferometer, respectively. Measurement of laser induced damage threshold (LIDT) of the samples was performed at 355 nm, 8 ns pulses. The results showed that high substrate temperature was beneficial to crystallization of the film. Above 244 °C, the refractive index increased gradually with the substrate temperature rising. Whereas, it was exceptional at 210 °C that the refractive index was higher than those deposited at 244 and 277 °C. The tensile residual stresses were exhibited in all MgF₂ films, but not well correlated with the substrate temperature. In addition, the stresses were comparatively smaller upon JGS1 substrates. A tendency could be seen that the LIDTs reached the highest values at about 244 °C, and the films upon JGS1 had higher LIDTs than those upon UBK7 substrates at the same temperature. Meanwhile, the damage morphologies showed that the laser damage of the coating resulted from an absorbing center at the film-substrate interface. The features of the damages were displayed by an absorbing center dominated model. Furthermore, the reason of the difference in LIDT values was discussed in detail.     

Modelling consideration of praseodymium-doped fiber amplifiers for 1.3 μm wavelength applications

To obtain the temperature-sensitive rate equations, a new energy level diagram of Praseodymium ion (Pr³⁺) in a glass host is modelled. By solving the modified rate equations, an analytical expression is presented to investigate the temperature dependence of the signal gain of a praseodymium-doped fiber amplifier (PDFA). It is seen that a change in the signal gain slightly depends on the variation of the distribution of Pr³⁺-ions in transitions ³F₄ ↔ ³F₃ with the temperature. Numerical calculations are carried out for the temperature range which is changing from −20 to +60 °C. Pr³⁺-doped ZBLAN fiber amplifier pumped at 1017 nm and Pr³⁺-doped sulfide fiber amplifier pumped at 1028 nm are selected as an application for the 1.3 μm signal wavelengths. It is also seen that the prediction of the model is in good agrement with their experimental results.     

Structure and optical properties of chemically synthesized titanium oxide deposited by evaporation technique

Titanium oxide inorganic ion exchange material was synthesized by hydrolysis with water and ammonia solution. Structural feature of the synthesized titanium oxide was analyzed using X-ray diffraction, X-ray fluorescence and infrared spectrometer technique. Tentative formula of titanium oxide was determined and written as TiO₂·0.58H₂O. Titanium oxide films were deposited on glass substrates by means of an electron beam evaporation technique at room temperature from bulk sample. The films were annealed at 250, 350, 450, and 550 °C temperatures. Transmittance, reflectance, optical energy gap, refractive index and extinction coefficient were investigated. The transmittance values of 85% in the visible region and 88% in the near infrared region have been obtained for titanium oxide film annealed at 550 °C. Kubelka-Munk function was used to evaluate the absorption coefficient which was used to determine the optical band gap. It was found that the optical band gap increases with increasing annealing temperature whereas the refractive index and extinction coefficient decreases.     

Design and fabrication of an intrinsically gain flattened Erbium doped fiber amplifier

We report design and subsequent fabrication of an intrinsically gain flattened Erbium doped fiber amplifier (EDFA) based on a highly asymmetrical and concentric dual-core fiber, inner core of which was only partially doped. Phase-resonant optical coupling between the two cores was so tailored through optimization of its refractive index profile parameters that the longer wavelengths within the C-band experience relatively higher amplification compared to the shorter wavelengths thereby reducing the difference in the well-known tilt in the gains between the shorter and longer wavelength regions. The fabricated EDFA exhibited a median gain ?28 dB (gain excursion below ±2.2 dB within the C-band) when 16 simultaneous standard signal channels were launched by keeping the I/P level for each at −20 dBm/channel. Such EDFAs should be attractive for deployment in metro networks, where economics is a premium, because it would cut down the cost on gain flattening filter head.     

Long-period fiber-gratings produced by exposure with a low-pressure mercury lamp and their sensing characteristics

A new production method of long-period fiber-gratings using neither a laser nor a fine-positioning system was proposed. A low-pressure mercury lamp emitting 254 nm ultraviolet light was used as a light source. Hydrogen-loaded Ge-B co-doped fiber was exposed to the emission of the lamp through an amplitude mask. A coupling loss up to 23 dB was obtained for a grating period of 212 μm. The maximum coupling loss for a grating period of 460 μm was 18 dB. The growth rate of the refractive index change by mercury-lamp exposure was 1.3 × 10⁻⁴/h. The temperature and strain characteristics were measured and compared with those fabricated by excimer-laser exposure. The temperature and strain sensitivities of long-period gratings with a period of 212 μm were higher than those of 460 μm. The temperature and strain sensitivities of those by mercury-lamp exposure were almost equal to those by excimer-laser exposure of the same fiber. The sensitivities of those by excimer-laser exposure of non-loaded fiber were higher than those of hydrogen-loaded fiber by mercury-lamp or excimer-laser exposures except for the temperature sensitivity of a grating period of 460 μm.     

Investigation of intermodal interference of LP01 and LP11 modes in the liquid-core optical fiber for temperature measurements

The intermodal interference of the LP₀₁ and LP₁₁ modes and determination of the equalization wavelength in the liquid-core optical fiber is presented. Theoretically was described the weakly guiding optical fiber with the constant core radius, where equalization wavelength is a function of the refractive indices of core and cladding. The dependence of equalization wavelength on refractive indices is employed for measurement of temperature. Temperature sensitivity using intermodal interference of modes LP₀₁ and LP₁₁ was documented in the liquid-core optical fiber consisted of fused silica as cladding and medicinal oil as a core. In the investigated temperature range the intermodal interference allows the temperature measurement with resolution of about 0.02 °C.     

Discrimination of strain and temperature based on a polarization-maintaining photonic crystal fiber incorporating an erbium-doped fiber

A simple sensing method for simultaneous measurement of temperature and strain is investigated by using a Sagnac fiber loop mirror composed of a polarization-maintaining photonic crystal fiber (PM-PCF) incorporating an erbium-doped fiber (EDF). Amplified spontaneous emission created by a pumped EDF is transmitted to a Sagnac fiber loop mirror. The interference between two counter-propagating signals in a Sagnac fiber loop mirror generates a periodic transmission spectrum with respect to wavelength. When external temperature is increased, the transmission peak power reduces because the amplified spontaneous emission of the EDF is decreased by the applied temperature change (0.04 dB/°C). The peak wavelength is shifted into the shorter wavelength because of the negative temperature dependence of the birefringence of the PM-PCF (0.3 pm/°C). As the applied strain increases, the peak wavelength of the transmission spectrum of the Sagnac loop mirror incorporating the EDF shifts into a longer wavelength (1.3 pm/με) because the phase change of the proposed sensing probe is directly proportional to the applied strain. The transmission peak power, however, is not changed by the applied strain. Since the source and the sensing probe are integrated, the overall system configuration is significantly simplified without requiring any additional broadband light source. Therefore, it is possible to simultaneously measure temperature and strain by monitoring the variation of transmission peak power and peak wavelength, respectively.     

Structural, electrical and optical properties of ZnS films deposited by close-spaced evaporation

ZnS films have been deposited on glass substrates by close-spaced evaporation (CSE) technique. The films were grown at different temperatures in the range, 200-350 °C. The layers have been characterized with X-ray diffractometer (XRD), atomic force microscope (AFM), energy dispersive analysis of X-rays (EDAX) and optical spectrophotometer to evaluate the quality of the layers for photovoltaic applications. The studies showed that the optimum substrate temperature for the growth of ZnS layers was 300 °C. The films grown at these temperatures exhibited cubic structure with nearly stoichiometric composition. The AFM data revealed that the films had nano-sized grains with a grain size of ∼40 nm. The optical studies exhibited direct allowed transition with an energy band gap of 3.61 eV. The other structural and optical parameters such as lattice stress, dislocation density, refractive index and extinction coefficient were also evaluated. The temperature-dependent conductivity measured in the range, 303-523 K showed a change in the conduction mechanism at 120 °C. The activation energy values evaluated using the temperature dependence of electrical conductivity are 7 and 29 meV at low and high temperature regions, respectively.     

A broadband ultra flattened chromatic dispersion microstructured fiber for optical communications

A double-cladding microstructured fiber (MF) is proposed in this paper. The inner cladding of this optical fiber is composed of elliptical air holes and silica. The dependence of dispersion on the diameter of the air holes, the pitch, and the axes of the elliptical holes is investigated numerically. The proposed fiber possesses an ultra flattened dispersion curve over a wide wavelength range, and its dispersion value is small. The effective mode area is approaching to 60 μm², and the confinement loss is as low as <0.025 dB/km at 1550 nm. While choosing suitable structure parameters, an ultra dispersion-flattened MF within a broadband from1000 nm to 1900 nm can be achieved. The dispersion fluctuation is 0.6-1.0 ps/(nm·km) in all S, C and L band.     

The preparation and refractive index of BST thin films

Radio-frequency magnetron sputtering technique is used to deposit Ba_0.65Sr_0.35TiO₃ (BST) thin films on fused quartz substrates. In order to prepare the high-quality BST thin films, the crystallization and microstructure of the films were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM). More intense characteristic diffraction peaks and better crystallization can be observed in BST thin films deposited at 600 °C and subsequently annealed at 700 °C. The refractive index of the films is determined from the measured transmission spectra. The dependences of the refractive index on the deposition parameters of BST thin films are different. The refractive index of the films increases with the substrate temperature. At lower sputtering pressure, the refractive index increases from 1.797 to 2.197 with pressure increase. However, when the pressure increases up to 3.9 Pa, the refractive index reduces to 1.86. The oxygen to argon ratio also plays an important effect on the refractive index of the films. It has been found that the refractive index increases with increase in the ratio of oxygen to argon. The refractive index of BST thin films is strongly dependent on the annealing temperature, which also increases as the annealing temperature ascends. In a word, the refractive index of BST thin films is finally affected by the films’ microstructure and texture.     

Determination of nonlinear coefficient and group-velocity-dispersion of bismuth-based high nonlinear optical fiber by four-wave-mixing

Nonlinear coefficient and group-velocity-dispersion of bismuth-based nonlinear fibers were determined by four-wave-mixing measurements. The wavelength dependence of refractive index of bulk bismuth-based glasses was also measured to estimate the material dispersion and waveguide dispersion. A newly developed bi-directional four-wave-mixing configuration enabled us to determine all fiber parameters simultaneously. The obtained fiber nonlinearity γ ∼ 1000 W⁻¹ km⁻¹ of bismuth-based nonlinear fiber is the highest one in the step-index fiber made of oxide glasses as expected from a high refractive index at 1550 nm. Dispersion analysis reveals that the both material dispersion and waveguide dispersion affect to the large group-velocity-dispersion of bismuth-based nonlinear fiber.     

Deep ultraviolet femtosecond laser tuning of fiber Bragg gratings

A deep ultraviolet femtosecond laser operating at wavelength 258 nm was demonstrated to be effective in trimming fiber Bragg gratings in telecommunication fibers. A smooth tunable resonance wavelength shift of up to 0.52 nm has been observed, corresponding to a refractive index change of ∼5 × 10⁻⁴ after an accumulated laser fluence of 63.3 kJ/cm² at a single pulse fluence of 124 mJ/cm². The ultrafast laser enhancement of ultraviolet photosensitivity response and modification of anisotropic index profile in silica fiber is a powerful technique to precise control of the performance of fiber Bragg grating devices for applications in optical filtering and polarization mode dispersion management.     

Thermally tunable microfiber knot resonator based erbium-doped fiber laser

A compact and tunable erbium-doped fiber laser is demonstrated using a highly doped fiber and a microfiber knot resonator (MKR) structure which is laid on the surface of a small peltier. The MKR functions as both a reflector and a tunable filter where tunability is achieved by varying the temperature of the resonator by heating the peltier. A stable laser output is achieved at the 1533 nm region with an optical signal to noise ratio (OSNR) of 27 dB using a 65 mW of 980 nm pump power. The operating wavelength of the laser can be tuned from 1532.60 nm to 1533.49 nm as the temperature is increased from the room temperature of 24 to 90 °C. It is observed that the operating wavelength shifts to a longer wavelength as the temperature increases with an efficiency of 12.4 pm/°C. This is due to the thermally induced optical phase shift attributable to the changes in effective refractive index and optical path length of the MKR loop.