Design and performance analysis in multiuser optical CDMA systems

The article presents comparative performance analysis of the proposed Optical CDMA system for 32 and 16 users with two dimensional codes. Numerical simulations have been done under interference significant environment, considering noise and dark current at data rates 2.5, 5, 7.5 and 10 Gbps over single mode fiber for transmission distance of more than 270 km. Results illustrate overall good performance, degraded with augment in bit rate and transmission distance, impervious with raise in number of simultaneous active users. Depicts significant performance improvement with inclusion of forward error correction RS (255,239), for low attenuation and chirp factor. It perceived, this is one of the efficient functional techniques for next generation broadband optical networks together with higher security owing to encoding and decoding, as it allow multiple users in the network to access the same fiber channel asynchronously.     

Enhanced performance for 10 Gb/s long reach RSOA based WDM-PON by using power pre-emphasized OFDM signal

An extended reach 10 Gb/s wavelength division multiplexing passive optical networks (WDM-PONs) system based on reflective semiconductor optical amplifier (RSOA) is proposed by using power pre-emphasized orthogonal frequency division multiplexing (OFDM) signal. Experimental results show that the proposed technique can effectively enhance the system performance against the limited bandwidth and chirp induced fading effect from direct modulation of RSOA. The receiver sensitivity is improved by 5 dB at the limit of BER for forward error correction (FEC) code over the 60 km and 85 km fiber transmission without any dispersion compensation module.     

2.50 Gbit/s optical CDMA over FSO communication system

Optical CDMA over FSO communication system is very effective to provide high data rate transmission with very low bit error rate and low amount of multiple access interference. In this paper, we have presented optical CDMA over FSO communication system to the range of 8000 m. The simulative results reveal that the transmission distance is limited mainly by the multi-access interference (MAI) which arises when there are number of users in the system because of the fact that one user data becomes noisy for all other users in the channel.     

Reduction of frequency fading and imperfect frequency response with pre-emphasis technique in OFDM-ROF systems

In this paper, a novel technique is proposed and experimentally demonstrated to reduce the effect of frequency fading (FF) and imperfect frequency response in direct-detection (DD) optical orthogonal frequency division multiplexing-radio-over-fiber (OFD-MROF) systems. To overcome FF effect in the optical fiber and imperfect frequency response in the optical and electrical devices at the high frequency, we pre-emphasize the power of the millimeter wave (mm-wave) OFDM sub-carriers appropriately in the center station. Experimental result of the proposed system shows the received sensitivity has been improved about 2 dB at the BER of 1 × 10^− 4 after 50 km SSMF transmission for 2.5 Gb/s OFDM signal carried on 60 GHz optical mm-wave compared to the original system without pre-emphasis technique.     

The analysis of the error statistics in a 5 × 40 Gbit/s fibre link with hybrid amplification

We quantify the error statistics and patterning effects in a 5 × 40 Gbit/s WDM RZ-OOK SMF/DCF fibre link using hybrid Raman/EDFA amplification. By extensive use of a numerical model, we determine how the error statistics change with the transmission distance. This knowledge is used as a basis for a constrained coding technique in order to improve the transmission error rate. We propose an adaptive constrained code for mitigation of the patterning effects and demonstrate that this approach can substantially reduce the bit error rate (BER) even for very large values of the channel BER (BER > 10^− 1). The proposed technique can be used in combination with forward error correction schemes (FEC) to extend the range of channel BERs that an FEC scheme is effective over.     

Giga-bit optical receiver for plastic optical fibre

An optical receiver with high sensitivity and linearity specially designed for Giga-bit communications over small-bandwidth high-attenuation multimode plastic optical fiber is presented. An automatic gain control transimpedance amplifier and linear post amplifiers are used to maintain a good performance with multilevel modulation. Using multilevel signaling and large-diameter integrated photodiodes make the presented optical receiver suitable for large core plastic optical fiber. For a wavelength of 675 nm, a sensitivity of −26.3 dB m (BER = 10⁻⁹) at 500 Mb/s is presented by a binary signal. A data rate of 1 Gb/s and a sensitivity of −19.8 dB m (BER = 10⁻⁹) are achieved with four-level pulse amplitude modulation.     

Using Fabry-Perot laser diode and reflective semiconductor optical amplifier for long reach WDM-PON system

In this investigation, we propose and investigate the simple self-injection locked Fabry-Perot laser diodes (FP-LDs) in optical line terminal (OLT); and wavelength-tunable optical network unit (ONU) using reflective optical semiconductor amplifier (RSOA) and FP-LD laser for downstream and upstream traffic in long reach (LR) wavelength division multiplexed-passive optical network (WDM-PON) respectively. The output performance of the proposed two laser sources in terms of power and side-mode suppression ratio (SMSR) has been discussed. Here, for the downstream traffic, the proposed optical transmitter can be directly modulated at 2.5 Gb/s on-off keying (OOK) format with nearly 0.4 dB power penalty at bit error rate (BER) of 10⁻⁹ through 75 km single-mode fiber (SMF) transmission. Moreover, the proposed upstream transmitter can be directly modulated at 1.25 and 2.5 Gb/s with nearly 0.5 and 1.1 dB power penalty, respectively, at the BER of 10⁻⁹.     

Optimal design of 32 channels spectrum slicing WDM for optical fiber access network system

In this article, the spectrum sliced dense wavelength division multiplexed passive optical network (SS-DWDM–PON) has been investigated as a power efficient and cost effective solution for optical access networks. In this work an AWG demultiplexer is used to operate as slicing system. The high speed SS-DWDM system has been realized and investigated for 32 channels with data rate up to 3 Gb/s using broadband ASE source (LED). The 3 Gb/s signals both non-return-to-zero (NRZ) and return-to-zero (RZ) were demonstrated in 40 km optical fiber link with BER < 10⁻¹². The results obtained here demonstrate that SS-DWDM is well suited for Fiber-to-the-Home (FTTH) network.     

1 Gbit/s transmission over step-index plastic optical fiber using an optical receiver with an integrated equalizer

A single chip optical receiver with an integrated large-diameter photodiode, transimpedance amplifier, two stages active equalizer, post amplifier and 50 Ω driver is used for gigabit transmission over PMMA step plastic optical fiber (SI-POF). The large-diameter photodiode with an antireflection coating optimized for red light. The integrated equalizer enables the presented optical receiver to reach 1 Gbit/s over 50 m SI-POF at bit error ratio of 10^− 6. An error free (< 10^− 9) 1 Gbit/s data rate over 40 m standard PMMA step-index plastic optical fiber is also achieved.     

A divided spectrum balanced detection technique for intensity noise reduction in SAC OCDMA systems

In this paper we propose a simple divided spectrum balanced detection (DSBD) for spectral amplitude coding (SAC) optical code division multiple access (OCDMA) systems. SAC OCDMA systems are limited by phase induced intensity noise (PIIN), which is a signal dependent source of noise. Our proposed technique reduces the PIIN by dividing the spectrum of the signal into two or more, and detecting each spectrum by a different photodiode. The DSBD scheme reduces the detected optical power at photodetection, thus resulting in a higher mitigation of the PIIN. Theoretical results show that DSBD demonstrate noticeable improvement over traditional balanced detection technique, for example an up to 33% increase in the number of active users can be achieved, and at least 1 × 10⁻³ b/s Hz increase in the spectral efficiency is obtained. However, the SDBD is more complex and append more constrains on system components.     

Fiber-wireless (FiWi) access network: Performance evaluation and scalability analysis of the physical layer

The fiber-wireless (FiWi) access network is a prestigious architecture for next generation (NG) access network. NG access networks are proposed to provide high data rate, broadband multiple services, scalable bandwidth, and flexible communication for manifold wireless end-users (WEUs). In this paper, the FiWi access network is designed based on a wavelengths division multiplexing/time division multiplexing passive optical network (WDM/TDM PON) at the optical backhaul with data rate of 2.5 Gb/s and wireless fidelity-worldwide interoperability for microwave access (WiFi–WiMAX) technologies at the wireless front-end along a 50 m–5 km wireless links with data rate of 54–30 Mb/s, respectively. The performance of the optical backhaul and the wireless front-end, in the proposed FiWi access network, has been evaluated in terms of bit error rate (BER), error vector magnitude (EVM), and signal-to-noise ratio (SNR) of the physical (PHY) layer. The scalability of the optical backhaul based on maximum split ratio of 1/32 for each wavelength channel and a fiber length of 24 km from the central office (CO) to the access point (AP) is analyzed with bit error rate (BER) of 10⁻⁹.     

3,3′-Benzene-1,4-diylbis[1-(substituted)phenylprop-2-en-1-one] derivatives: A new class of materials for third-order nonlinear optical applications

We have investigated the third-order nonlinear optical parameters of Bischalcones embedded in DMF solution and in solid PMMA matrix, by Z-scan technique using nanosecond laser pulse trains at 532 nm. Z-scan results reveal that the Bischalcones exhibits negative nonlinear refractive index as high as 10⁻¹¹ esu. The molecular two-photon absorption cross-section of Bischalcones were of the order 10⁻⁴⁶ cm⁴ s/photon, which is nearly two orders of magnitude larger than that of Rhodamine 6G which is 10⁻⁴⁸ - 10⁻⁵⁰ cm⁴ s/photon. We found that, the two-photon absorption (TPA) is the dominating nonlinear process leading to nonlinear absorption in both the cases in solution and as well as in solid medium. Based on TPA process, the Bischalcones exhibit good optical power limiting of nanosecond laser pulses at the input wavelength. The nonlinear optical parameters found to increase on enhancing the strength of the electron donor groups indicating the dependence and importance of electron donor/acceptor units on third-order nonlinear optical susceptibility χ⁽³⁾.     

On the carrier generation and HD signal transmission using the millimeter-wave radio over fiber system

The dual sideband optical carrier suppression (DSB-OCS) technique is employed in the optical carrier generation for 40 GHz radio over fiber (ROF) system. A dual electrode Mach-Zehnder modulator (DE-MZM) with the minimum transmission bias (MiTB) technique is employed to build the system. The results show that, a 40 GHz carrier is successfully generated with the amplitude up to −29 dBm and signal to noise ratio (SNR) of 35 dB and a high definition (HD) signal is successfully transmitted using the system. Finally, the bit error rate (BER) measurement is carried out for the system with 1.25 Gbps OOK signal showing an error free 40 GHz ROF system with almost no penalty between the back to back and 20 km fiber for a BER of 10⁻⁹.     

Transmission system over 3000 km with dispersion compensated by chirped fiber Bragg gratings

The limitation of the system with dispersion compensation by chirped fiber Bragg gratings is investigated in this paper. The transmission distance of the system based on chirped fiber Bragg gratings surpasses 3000 km. The bit error rate (BER) of the system is below 10⁻⁹ for as long as 2000 km. The BER is about 10⁻⁷ at 3000 km and, when forward error correction (FEC) is added, zero BER can be achieved. It is the longest transmission system with dispersion compensation by chirped fiber Bragg gratings.     

A novel super-FEC code based on concatenated code for high-speed long-haul optical communication systems

The structures of the novel super forward error correction (Super-FEC) code type based on the concatenated code for high-speed long-haul optical communication systems are studied in this paper. The Reed-Solomon (RS) (255, 239) + Bose-Chaudhuri-Hocguenghem (BCH) (1023, 963) concatenated code is presented after the characteristics of the concatenated code and the two Super-FEC code type presented in ITU-T G.975.1 have theoretically been analyzed, the simulation result shows that this novel code type, compared with the RS (255, 239) + convolutional-self-orthogonal-code (CSOC) (k₀/n₀ = 6/7, J = 8) code in ITU-T G.975.1, has a lower redundancy and better error-correction capabilities, and its net coding gain (NCG) at the third iteration is 0.57 dB more than that of RS (255, 239) + CSOC (k₀/n₀ = 6/7, J = 8) code in ITU-T G.975.1 at the third iteration for the bit error rate (BER) of 10⁻¹². Therefore, the novel code type can better be used in long-haul, larger capacity and higher bit-rate optical communication systems. Furthermore, the design and implementation of the novel concatenated code type are also discussed.     

Effect of swift heavy ion irradiation on photoluminescence properties of ZnO/PMMA nanocomposite films

We report a study on the SHI induced modifications on structural and optical properties of ZnO/PMMA nanocomposite films. The ZnO nanoparticles were synthesized by the chemical route using 2-mercaptoethanol as a capping agent. The structure of ZnO nanoparticles was confirmed by XRD, SEM and TEM. These ZnO nanoparticles were dispersed in the PMMA matrix to form ZnO/PMMA nanocomposite films by the solution cast method. These ZnO/PMMA nanocomposite films were then irradiated by swift heavy ion irradiation (Ni⁸⁺ ion beam, 100 MeV) at a fluence of 1×10¹¹ ions/cm². The nanocomposite films were then characterized by XRD, UV-vis absorption spectroscopy and photoluminescence spectroscopy. As revealed from the absorption spectra, absorption edge is not changed by the irradiation but the optical absorption is increased. Enhanced green luminescence at about 527 nm and a less intense blue emission peak around 460 nm were observed after irradiation with respect to the pristine ZnO/PMMA nanocomposite film.     

Design of an ultrafast all-optical NOR logic gate based on Mach-Zehnder interferometer using quantum-dot SOA

This paper proposes a design for all-optical NOR logic gate, based on Mach-Zehnder interferometer (MZI) using quantum-dot semiconductor optical amplifier (QD-SOA). In this regard, a theoretical model for an ultrafast all-optical signal processor is developed using QD-SOA to achieve high bit rate operation. We have demonstrated the NOR gate operation in two cases of with and without an optical control pulse. Simulations have been carried out at data bit rates 160 Gb/s, 200 Gb/s, and 250 Gb/s for the case that control pulse is not applied, and also at data bit rates 1 Tb/s and 2 Tb/s in presence of control pulse which leads to improvement of gain recovery time and ultrafast NOR logic operation. In addition, quality factors of the output signals in presence and without the control pulse at different bit rates with different bias currents have been investigated for pseudo-random binary sequence (PRBS) of word length 2⁸–1.     

170 Mb/s multilevel transmission over 115 m standard step-index plastic optical fiber using an integrated optical receiver

An optical receiver having a high linearity is used for multilevel communication over standard step plastic optical fiber. A large-diameter photodiode with an antireflection coating optimized for red light was integrated. These features enable the used optical receiver to be a promising plastic optical fiber receiver. An error free (< 10⁻⁸) 170 Mb/s data rate over 115 m standard PMMA step-index plastic optical fiber is achieved with four-level and eight-level pulse amplitude modulation.     

Influence of X-ray irradiation on the optical properties of CoMTPP thin films

Thin films of 5,10,15,20-Tetrakis (4-methoxyphenyl)-21H,23H-porphine cobalt (II), CoMTPP were prepared at room temperature (300K) by the thermal evaporation technique under vacuum pressure about 2 × 10^− 4Pa. The X-ray diffraction patterns showed the amorphous nature for the as-deposited and the irradiated films, whereas the powder has shown a polycrystalline with triclinic structure. Miller's indices, hkl, values for each diffraction peak in the XRD spectrum were calculated. Optical properties of CoMTPP thin films were characterized by using spectrophotometric measurements of transmittance and reflectance in the spectral range from 200 to 2500 nm. The refractive index, n, and the absorption index, k, were calculated. The obtained data were used to estimate the type of transitions and the optical and fundamental gaps before and after X-ray irradiation. In addition, the normal dispersion of the refractive index is discussed in terms of lorentz-lorentz free single oscillator model and modified lorentz Drude model of free carrier contribution.     

A novel block turbo code for high-speed long-haul DWDM optical communication systems

A novel super forward error correction (SFEC) coding scheme, based on the block turbo code (BTC) of Bose–Chaudhuri–Hocguenghem (BCH)(64,57)×BCH(64,57), in high-speed long-haul dense wavelength division multiplexing (DWDM) optical communication systems is proposed. The simulation results and its analyses show that the net coding gain (NCG) of the novel SFEC code at iteration 6 is, respectively, 0.31 and 0.34 dB more than those of the BCH(3860, 3824)+BCH(2040, 1930) code and Reed–Solomon (RS)(255,239)+convolutional–self-orthogonal code (CSOC)(k₀/n₀=6/7, J=8) code in the Recommendation of ITU-T G.975.1 at iteration 3 for the bit error rate (BER) of 10⁻¹². The performance analyses for the novel SFEC code show that it has excellent advantages such as the shorter component code and rapid encoding/decoding speed; thus, both the complexity to implement its software/hardware and the delay time for its encoding/decoding can be greatly reduced. As a result, the novel SFEC coding scheme can better be applicable in high-speed long-haul DWDM optical communication systems. In addition, the design and implementation of the novel BTC are also analyzed and probed.