全光纤干涉式结构中传感模式仿真分析

全光纤干涉式传感结构中包层模场与外界物理量作用,携带被感测信息,因此对包层模的研究是设计制作和提高该类传感器传感性能的关键.利用有限差分光束传播法获得传感光纤不同长度和不同芯径比时传感器对应的光谱,通过傅里叶变换获得其干涉频谱,计算出各主要参与干涉的包层模组的有效折射率,利用色散方程确定对应包层模.理论仿真结果显示,随着传感部分光纤长度增加,参与干涉的包层模式随之增加,并且向高阶模式变化,光谱变得稠密,是多阶包层模干涉的叠加,传感器输出干涉谱的自由光谱范围变小.随着输入光纤与传感光纤芯径比变化,会明显改变纤芯包层功率分布,同时,芯径比增大也会增加参与干涉的包层模种类和阶数.     

A theoretical study of the modal dispersion characteristics of an annular circular waveguide with helical winding as the outer cladding

In this present communication, we introduce a new type of annular optical waveguide whose outer cladding is made of sheath helix. The sheath helix is made up of the dielectric material of lower refractive index than the core materials. Using vector approach, the general characteristic equation for the proposed waveguide has been derived. The modal dispersion characteristics for the lowest-order modes for different pitch angles are determined and analyzed. We observe that there is no effect of pitch angles on dispersion curve nearly up to 89° but drastic change is observed at 90° and above pitch angle. On comparison of helically inner cladded annular circular waveguide, we have found that there is not the existence of the negative dispersion curve and photonic band gap in the helically outer cladded annular circular waveguide. It means only the inner cladding is responsible for the negative dispersion as well as photonic band gap. There is no effect of the outer cladding.     

Influence of uniaxial crystal material cladding on reflectivity and dispersion of uniform fiber Bragg grating

The fiber Bragg grating with cladding made of uniaxial crystal material whose optical axis is parallel to the axis of fiber Bragg grating proposed in the paper published in 2003 was investigated again and an error was corrected in the calculation, its effective index, reflectivity and dispersion were examined using coupled-mode theory and numeric solution. The calculated results indicate that no low frequency cutoff phenomenon exists in the HE₁₁ mode, more power is transmitted by the core of the fiber with cladding made of isotropic material, the reflectivity of the fiber Bragg grating with cladding made of uniaxial crystal material is much higher than that with cladding made of isotropic material, the parameter K_cl, i.e., the ratio of the extraordinary to the ordinary ray refractive index, has a stronger impact on the reflectivity, Bragg wavelength and the dispersion of this kind of fiber Bragg grating when it varied from 1.00 to 1.01 than in other regions. This means that the characteristics of the fiber Bragg grating with uniaxial crystal cladding can be changed through adjusting K_cl while keeping its length, periodicity and the other parameters as constants.     

The study of chromatic dispersion and chromatic dispersion slope of WI- and WII-type triple-clad single-mode fibers

In this paper, the chromatic dispersion and chromatic dispersion slope of two kinds of triple-clad single-mode fibers with a depressed index inner cladding named WI- and WII-type were examined. A feasible approach to calculate chromatic dispersion and higher-order dispersion was established successfully, and the influences made by the optical parameters and geometric parameters on the chromatic dispersion coefficient and its slope were analyzed in detail. The calculated results show that the optical parameter R₂, which symbolizes the third cladding effect, has a strong impact on the chromatic dispersion coefficient and the chromatic dispersion slope, and the degrees of such impact are closely related to the other parameters.     

包层为负折射率介质的抛物型渐变光纤色散特性分析

研究了纤芯为各向同性非均匀材料,而包层为负折射率均匀介质光纤的色散特性.在纤芯满足弱渐变条件的假定下,按矢量场分析法,通过芯层与包层的介电常数比ξ和磁导率比η,讨论了导波模式色散特性对左手介质包层材料的依赖性.分析表明,ξ和 η对轴对称模色散曲线的低频段影响较大,但对非轴对称模影响不大.ξ和 η对导波模式的截止频率没有影响.由于该光纤中的HEm1模的截止频率都等于0,所以不存在理论上的单模区,但仍可近似实现无色散传输.     

各向异性内包层对双包层光纤特性影响的分析

提出了单轴各向异性材料为内包层，且其主轴沿光纤轴线（z轴）方向的双包层光纤模型，推出了矢量模特征方程，重点研究了主轴折射率比kcl对波导色散的影响，针对从矢量模特征方程求解波导色散因表达式极为复杂而无法直接求解的困难，提出了一种求解波导色散的有效方法，研究结果发现可以在不改变光波导结构参量的条件下，通过改变kcl可有效地改变光纤的波导色散，也分析了kcl、几何参量S、光学参量R对低次模的传输和截止特性的影响。研究结果为获得更为理想的色散补偿、色散平坦光纤及设计新型无源光器件提供了重要的依据。     

基于双芯光子晶体光纤的低非线性宽带色散补偿光纤的设计

采用矢量光束传输法数值模拟了基于模式耦合的双芯光子晶体光纤的色散和非线性与其结构的关系。结果表明:通过在包层中移除一层空气孔以形成外纤芯并调整内外纤芯之间的距离及包层空气孔的占空比,内外纤芯间的模式耦合可以在宽带范围内发生,导致产生大负色散。同时,由于光场分布在两个纤芯内,增大了模场面积,产生低非线性,可以实现低非线性宽带色散补偿。     

双包层手性光纤中导模的光功率特性

在对W型阶跃双包层手性光纤进行解析求解的基础上,对几个低阶导模的功率特性进行了仔细的研究.对典型的内包层厚度,计算了几个低阶模留在纤芯中的光功率随纤芯和内外包层的手性参数的变化关系曲线,讨论了纤芯和内外包层的手性参量以及内包层厚度对不同符号模式的功率特性的影响.内包层厚度越大,功率越被限制在纤芯中.随着纤芯中手性参量的增大, HE－11模和HE－21模（HE01模）限制在纤芯中的光功率缓慢增加,而HE11模和HE21模（HE02模）限制在纤芯中的光功率则逐渐减小.包层手性参量的作用正好与此相反.     

双芯复合格点光子晶体光纤的负色散特性

介绍了一种双芯复合格点负色散光子晶体光纤,其包层是由连续电介质纯硅背景上挖出的两种大小不同的空气孔构成,芯区是由掺锗的高折射率的材料构成。为了实现负色散,还移去了包层中的一圈空气孔。采用频域有限差分法对其负色散特性进行分析表明,通过调整空气孔间距和两种空气孔的尺寸,可以得到不同程度的宽带负色散。当内芯半径取0.95μm,孔间距取2.15μm,大空气孔直径取1.9μm,小空气孔直径取1.1μm时,可在1.55μm处实现宽带负色散,其半峰全宽超过了200 nm。这种光纤的包层中空气孔呈六边形分布,空气孔的尺寸均大于1μm,降低了制作的难度。这种光纤可以用于波分复用光纤通信系统中的宽带色散补偿。     

Widely tunable asymmetric long-period fiber grating with high sensitivity using optical polymer on laser-ablated cladding

We demonstrate high-efficiency, wideband-tunable, laser-ablated long-period fiber gratings that use an optical polymer overlay. Portions of the fiber cladding are periodically removed by CO(2) laser pulses to induce periodic index changes for coupling the core mode into cladding modes. An optical polymer with a high thermo-optic coefficient with a dispersion distinct from that of silica is used on a deep-ablated cladding structure so that the effective indices of cladding modes become dispersive and the resonant wavelengths can be efficiently tuned. The tuning efficiency can be as high as 15.8 nm/ degrees C, and the tuning range can be wider than 105 nm (1545-1650 nm).     

Modal redistribution and power loss in on-fibre devices

The mode coupling and optical power loss taking place in on-fibre devices are investigated. These devices are fabricated by removing the cladding of a multimode fibre and replacing it with a new material such as electro-optic or magneto-optic. Under an application of an external field the index of this modified cladding increases, leading to coupling among guided modes and coupling to radiation modes, resulting in optical power loss. The coupling among guided modes and the power loss are calculated as a function of the change in the index under the field and the length of the active region for the case when HE_1m modes are excited individually or in a group. Results indicate that on-fibre devices may be used as low-loss devices for applications involving sensors and delay lines.     

Anomalous dispersion and group velocity properties in subwavelength uniaxial metamaterial waveguide with metal cladding

We investigate propagation behavior of electromagnetic waves in a slab uniaxial metamaterial waveguide with metal cladding and discuss the dispersion relation, group velocity and energy flux distribution of transverse electric guided modes in two kinds of uniaxial metamaterial waveguides with different orientations of optical axis in detail. The numerical results show that there exist anomalous dispersion properties such as backward modes existing in low-frequency range, and the group velocity can be negative or approach zero. If the orientation of optical axis is selected properly, each guided mode has two dispersion curves—one is normal dispersion and another belongs to anomalous dispersion and shows a transition from a backward mode to a forward one with the angular frequency increasing. In addition, the condition of the existence of cutoff frequency is clarified. These properties may have potential applications in optical information storage, optical communication, integrated optics and nanophotonic devices.     

光纤纤芯及包层模有效折射率计算及仿真

光纤结构设计、模间色散求解、光纤光栅模式耦合等问题的研究, 都需要对光纤纤芯及包层模的有效折射率进行精确计算. 本文以光纤三层结构模型为基础, 结合该模型下的模式本征方程, 使用截弦法求解了纤芯模有效折射率, 并将计算结果与COMSOL软件模拟的对应纤芯模的传输光场进行对比, 验证了计算结果正确.使用区间遍历算法对包层模有效折射率进行了求解, 与已有的传统方法相比, 该方法可以有效防止求解过程中根的遗漏、避免特征方程产生的奇点, 并能保证模式的正规性.本文采用Mathematica软件对求解过程进行仿真, 获得了纤芯模和包层模有效折射率与波长关系曲线. 关键词： 光纤传输模式 有效折射率 截弦法 区间遍历算法     

Existence of negative dispersion and band gap in a helically inner cladded annular circular waveguide

Helical waveguide, a different type of waveguide structure, has been considered for analysis of modal dispersion characteristics. This paper deals with the study of a new type of annular waveguide, in which the inner cladding is made by the helical windings i.e. sheath helix and the outer cladding is as usual simple step-index cladding. Using vector approach, the general characteristic equation for the proposed waveguide has been derived. The modal dispersion characteristics for the lowest order modes for different pitch angles and thickness are determined and analyzed. We have found that there is an existence of the negative dispersion curve in the helically inner cladded annular circular waveguide. It means that the inner cladding is responsible for the negative dispersion which is generally obtained in a photonic band gap.     

Single mode optical fiber characterisation by the LP11 mode radiation pattern

We describe a method for determining the V-value from the far-field radiation pattern of dual mode optical fibers (this method is an extension of the work by Gambling et al. for the LP₁₁ modes). The method involves measurements of the maximum radiation angle and the angle of the first minimum. Curves are presented which can be used with dual mode fibers, determining the core diameter, the refractive index difference between core and cladding, as well as the V-value in the single mode regime for longer wavelength operation with the help of dispersion curves of the dopant materials.     

单模手征光纤研究

对圆芯和内外包层都为手征介质构成的双包层手征光纤（W型）进行了解求解,导出了模式场解及模式特征方程,然后用数值计算的方法研究了手征参数对模式的色散曲线和截止频率的影响,结果发现在双包层光纤的纤芯中引入手征或在单包层光纤的包层中引入手征,都可以实现单模工作。     

一种新的低非线性宽带色散补偿微结构光纤的设计

采用矢量光束传输法对空气孔包层呈正六边形分布的微结构光纤的色散和非线性特性进行了数值模拟。通过分别调节内三层空气孔的直径和包层空气孔节距,设计了一种低非线性宽带色散补偿微结构光纤。该光纤在波长1.55 μm处具有－3 235.8 ps/nm/km的大负色散,可在以1.55 μm为中心的100 nm宽带波长范围对相当于自身长度190倍的普通单模传输光纤进行宽带色散补偿(色散补偿率偏移在0.5%以内),同时该光纤可在此宽带波长范围内保持非线性系数低于5 W^-1·km^-1。     

Flat-topped beam output from a double-clad rectangular dielectric waveguide laser with a high-index inner cladding

A novel method to produce a flat-topped laser beam by using a double-clad rectangular waveguide laser with high-index inner cladding is presented. The waveguide dispersion equation for cosine mode was deduced, the condition for the flattened mode was given out, relative gains for guided modes were calculated numerically and analyzed. Results indicate that a gain advantage for the flattened mode is clear, a flat-topped laser beam can be achieved when the optical confinement factor, the gain intensity and the output coupler are chosen suitably.     

A partially reflecting metal cladding: its effect on the modes of dielectric optical waveguides

If the metal cladding of a dielectric optical waveguide is sufficiently thin to be only partially reflecting, then the waveguide modes differ from those of the conventional metal-clad waveguide. The TE modes are little affected by a variation in the metal thickness but the TM modes change considerably due to a coupling between the waveguide modes and the surface plasma waves supported by both the metal: dielectric interfaces and the metal film. It is the refractive index of the dielectric cladding which is remote from the guiding core that determines whether the lowest order TM mode is the TM₀ or TM₁ mode. This dielectric cladding also strongly influences the attenuation of the TM modes and, if the guide supports a TM₀ mode, then the attenuation of the TM modes far from cut-off are an order of magnitude higher than that of the corresponding modes when the guide cannot support a TM₀ mode. If the guide can support a TM₀ mode then its dimensions can be chosen such that it will support the TE_N and TM_N modes with equal phase velocities. A lossless approximation is used to develop an expression which will specify the required guide dimensions directly and parametric plots of these dimensions are discussed.     

W-型单模单偏振光纤截止基模的能量损耗

给出了一种新的数值计算W型单模单偏振光纤截止基模能量损耗的方法－－区域模场边界条件匹配法。用这种方法分析了截止基模能量损耗与光张结构参数的关系。得出了截止基模能量损耗随椭圆内包层长半轴、短半轴或内包层折射率深度的增加而迅速减小，以及高椭圆度内包层情形下截止基模能量损耗仅由内包层短半轴、内包层折射度和纤芯－外包层相对经差确定的结论；同时得出了截止基模能量损耗与纤芯－外包层相对折射率差的平方根成正比的解析结果。最后将数值计算和实验进行了比较，两者较为一致。