Spectral beam combining of 2 μm Tm fiber laser systems

Output beams from three independently frequency-stabilized thulium master-oscillator power-amplifier fiber laser systems were spectrally combined using a plane-ruled metal diffraction grating. Two laser channels were frequency-stabilized with guided mode resonance filters and the third was stabilized using a plane-ruled metal diffraction grating. The systems had output wavelengths between 1984 and 2015 nm, each with a spectral width of 100-450 pm and output powers between 40-120 W. The combined beam had powers up to 49 W and was 32% efficient with respect to the launched pump power.     

Graphene-based passively Q-switched 2 μm thulium-doped fiber laser

We demonstrated stable pulses generation at 2 μm in a passively Q-switched thulium-doped fiber laser using a few layer graphene thin film. The maximum output power was 4.5 mW and the single pulse energy was 85 nJ at 53 kHz repetition rate, and the pulse width was about 1.4 μs. The pulse width and the repetition rate of the Q-switched fiber laser can be changed along with the pump power. To the best of our knowledge, this is the first report of graphene saturable absorber for passively Q-switched 2 μm fiber lasers.     

Investigation of 2.0 μm emission in Tm and Ho co-doped oxyfluoride tellurite glass

This paper reports 2.0 μm emission properties of Tm³⁺/Ho³⁺ co-doped oxyfluoride tellurite glass exited by 808 nm laser diode (LD). Mid-infrared transmittance property of glass was investigated by Fourier transform infrared (FTIR) spectrometer. The real chemical composition of investigated glass was identified by X-ray photoelectric spectroscopy (XPS). Thermal stability of the glass was determined by differential thermal analysis (DTA) measurement. The Judd-Ofelt parameters, spontaneous radiative transition probabilities, branching ratios and radiative lifetime of Ho³⁺ were calculated based on the absorption spectra by using Judd-Ofelt theory. Results indicate that the maximum 2.0 μm emission intensity attributed to the ⁵I₇→⁵I₈ transition of Ho³⁺ was achieved at 1.5 mol% Tm₂O₃ and 1 mol% Ho₂O₃ concentrations in oxyfluoride tellurite glass. OH⁻ absorption at 3000 cm⁻¹ was greatly depressed by introduction of 10 mol% F⁻. The maximum absorption and stimulated emission cross-section of Ho³⁺ near 2.0 μm are 7.0×10⁻²¹ cm² at 1950 nm and 8.8×10⁻²¹ cm² at 2048 nm, respectively. The calculated radiative lifetime of 4.4 ms for ⁵I₇→⁵I₈ transition and large stimulated emission cross-section of the Tm³⁺/Ho³⁺ co-doped oxyfluoride tellurite glass indicate that the glass has a potential application in efficient 2.0 μm laser.     

Welding of polymers using a 2 μm thulium fiber laser

Absorber-free transmission and butt-welding of different polymers were performed using thulium fiber laser radiation at the wavelength 2 μm. The relations between the laser process conditions and the dimensions and quality of the seam were investigated by means of optical and phase-contrast microscopy. Mechanical properties of the weld joints were studied in tensile strength tests. Laser-welded polyethylene samples revealed a tensile strength of greater than 80% of the bulk material strength. Transmission welding of different polymer combinations featured the formation of different joint classes depending on the spectral properties. The experiments demonstrate new application areas of mid-IR fiber laser sources for materials processing.     

Tunable CW Tm,Ho:YLF laser at 2μm

A tunable continuous wave (CW) low temperature operating Tm (6 at.-%),Ho (0.6 at.-%):YLF laser pumped by fiber-coupled diode laser is reported. The maximum output power is 4.16 W at 2073 nm by use of 30% output coupling, the slope efficiency is 33%. A tuning range from 2049 to 2081 nm is achieved with a birefringent filter (BF). The factors that contribute to the output power and tuning range are discussed.     

Performance of 2 μm Tm:YAP pulse laser based on a carbon nanotube absorber

We demonstrated the first use of carbon nanotube as a saturable absorber in the Q-switched and Q-switched mode-locking of a diode pumped Tm:YAP operating at 2 μm. At the incident pump power of 8.64 W, the minimum Q-switched pulse width of 255.1 ns, and the maximum peak power 53.1 W can be obtained with the corresponding repetition rate of 21.76 kHz. The performance of a diode-pumped passively Q-switched mode-locked Tm:YAP laser with high repetition rate formed with a folded cavity. As high as 780 mW average output power was produced in QML laser. The repetition rate of the mode-locked pulse inside the Q-switched envelope was 244.1 MHz. The dependence of the operational parameters on the pump power was also investigated experimentally.     

2.1μm Ho：LuAG ceramic laser intracavity pumped by a diode-pumped Tm：YAG laser

We report a compact Ho：LuAG ceramic laser intracavity pumped by a diode-pumped Tm：YAG ceramic laser. The laser oscillation is accomplished by using a common linear cavity configuration containing Tm：YAG and Ho：LuAG ceramics. The 1.0 at.% Ho：LuAG ceramic laser yields 1.15 W of maximum output simultaneously at 2094 and 2100 nm with a beam quality factor of M2-2.8.     

Temperature-dependent absorptance of painted aluminum, stainless steel 304, and titanium for 1.07 μm and 10.6 μm laser beams

We measured the temperature-dependent absorptance of metals (Al, Ti, SS304) for continuous beams from 1.07 μm fiber laser and 10.6 μm CO₂ laser using power sensors and infrared (IR) pyrometers. The absorptance measurements were repeated for metals with three different paint coatings. For measurements at elevated temperatures up to the melting point, integrating sphere is not practical since high temperature radiation from a heated target disturbs weak output from the sphere considerably. Our results provide how each metal, whether coated or uncoated, absorbs the infrared beams as temperature is elevated to a melting point. A polynomial approximation to the measured absorptance of each target is provided for modeling of the laser-metal interaction at elevated temperatures.     

2-μm mode-locked nanosecond fiber laser based on MoS_2 saturable absorber

We demonstrated a 2-μm passively mode-locked nanosecond fiber laser based on a MoS_2 saturable absorber(SA).Owing to the effect of nonlinear absorption in the MoS_2 SA, the pulse width decreased from 64.7 to 13.8 ns with increasing pump power from 1.10 to 1.45 W. The use of a narrow-bandwidth fiber Bragg grating resulted in a central wavelength and 3-dB spectral bandwidth of 2010.16 and 0.15 nm, respectively. Experimental results show that MoS_2 is a promising material for a 2-μm mode-locked fiber laser.     

Room temperature operation of 2-μm microchip Tm,Ho:Lu2SiO5 laser

Room temperature operation of a c-cut microchip Tm,Ho:Lu₂SiO₅ laser end-pumping by a fibercoupled laser-diode is reported. A 4.03 W incident pump power is used to generate a maximum laser output of 98 mW, representing 2.43% optical-to-optical conversion efficiency and a 4.38% slope efficiency corresponding to incident power. In the experiment, the oscillating wavelengths shifting from 2.084 to 2.089 μm has been observed and approximately 10 mW single 2.087 μm wavelength oscillation has been obtained by changing the pump power to 1.43 W and the position of the pump focus.     

Investigation of 1.06 μm laser induced plasma in air using optical interferometry

The laser produced plasma in air by Q-switch Nd:YAG pulses with 50 mJ and 7 ns was analyzed using Mach-Zehnder interferometer. The interferograms were taken at various delay times after single pulses induced gas breakdown. The 3D electron density distribution at early times of the plasma is investigated. To determine the 3D electron density distribution of the plasma, the FFT analysis is applied to extract the phase of the reconstructed interferograms and the numerical inverse Abel transformation is used to calculate the refractive index. The results provide an understanding of the electron density temporal and spatial evolution of laser induced plasma in air from 18 ns and up to 100 ns of plasma lifetime.     

LD pumped 2-μm CW laser from Tm,Ho:GdVO_4

A set of fiber-coupled continuous wave (CW) diode lasers has been used to pump Tm, Ho:GdVO_4 and generate 2.048-μm laser radiation at liquid nitrogen temperature. The optical-optical efficiencies of 25%, output power of 3.5 W, and pumping threshold of 838 mW have been obtained and compared with those from Tm, Ho:YLF under identical experimental conditions.     

Investigation on achieving the diode-pumped weak line laser at 1.3 μm

In this paper, a continuous-wave (CW) diode-side-pumped Nd:YAlO₃ (Nd:YAP) laser operating at the weak line of 1339 nm has been achieved and investigated. The output of the 1339 nm laser was realized based on the polarization selection and reasonable transmittance design. The relationship between the output powers and resonator lengths of the 1339 nm Nd:YAP laser has been studied and the optimum resonator length was adopted to improve the output power. As high as 31.3 W output power of the a-axis polarized 1339 nm laser has been obtained at the pumping power of 555 W with the optical-optical and slope efficiencies to be 5.6% and 13%, respectively. This work will provide an effective way to obtain the weak line lasers for potential applications in spectroscopy, coherent terahertz generation, etc.     

Amplification characteristics measurement of 1.55 μm multi-mode LD

The amplification characteristics of 1.55 μm multi-mode LD are presented experimentally. It demonstrates that nine wavelengths across 1547–1557 nm have a good amplification, the maximum gain of ∼43 dB at 1552.14 nm is obtained with pump power of 130 mW @980 nm, and noise figure of ∼5.6 dB at 1554.3 nm is achieved.     

Comparison of Tm : ZBLAN and Tm : silica fiber lasers; Spectroscopy and tunable pulsed laser operation around 1.9 μm

Tm-doped ZBLAN and Tm-doped silica glass are compared spectroscopically and the fiber lasing of the Tm ³F₄³H₆ transition around 1.9 m in ZBLAN and silica fibers is compared. The spectroscopy of these materials indicates that Tm:ZBLAN possesses advantages over Tm:silica glass due to the lower phonon energies. The phonon energy in these glass hosts influences both the pump manifold lifetime, the Tm ³H₄, and the upper laser manifold lifetime, the Tm ³F₄. The maximum phonon energy in Tm:ZBLAN, 500 cm^-1 , compared to Tm:silica, 1100 cm^-1, leads to better Tm–Tm self quenching towards populating the Tm ³F₄, as well as better Tm ³F₄³H₆ quantum efficiency. A spectroscopic analysis using the Judd–Ofelt theory and measured lifetimes are used to assess the merits of Tm:ZBLAN over Tm:silica as a fiber laser material. Diode-pumped fiber lasing experiments show that Tm:ZBLAN possesses advantages over Tm:silica that are believed to be due to a lower phonon energy. Data is presented for launched pump energy versus laser energy, fiber length versus slope efficiency, and output mirror reflectivity versus slope efficiency. Tm:ZBLAN is demonstrated to possess higher slope efficiencies and lower thresholds, than Tm:silicate. A grating tuned Tm:ZBLAN laser is also demonstrated for tunable operation between 1.893 m and 1.955 m. PACS 42.55.Wd; 42.55.Xi; 42.62.Fi; 78.55.Qr     

Design of a pressure sensor of 0–7 bar in fiber optic using MMI methodology

This research shows the possibility of measuring pressure in the range of 0–7 bar and the comparison against 2 commercial sensors. The technique used is based on the multimodal interference in a fiber optic singlemode–multimode–singlemode (SMS) to 1550 nm. The fiber optic is mounted on a plate of stainless steel AISI 316, where the bending of the plate will generate a curvature on the part of the multimodal fiber generating a decoupling of modes and this generates a low intensity to the output of the system.     

Continuous-tunable 4.144-4.851 μm twin-MgO:PPLN cascaded optical parametric generator pumped by a 1.342 μm Nd:GdVO4 laser

An all-solid-state mid-infrared optical parametric generator with wide tunability by using multi-grating periodically poled 5 mol.-% MgO-doped lithium niobate (MgO:PPLN) is reported. The pump source is a diode-pumped Q-switched Nd:GdVO₄ laser operated at 1.342 μm with pulse width of 150 ns and repetition rate of 50 kHz. To extend the interaction length, two identical multi-grating MgO:PPLN crystals have been cascaded in the OPG system. When the incident pump average power is 10 W, the obtained maximum idler output power is 340 mW at 4.144 μm. Compared with only using one multi-grating MgO:PPLN crystal, the obtained idler output power increases by 20.1%. 4.144-4.851 μm continuous-tunable idler output is obtained with six grating periods from 29 to 31.5 μm and temperature from 40 to 200 °C. To our knowledge, this is the first time to use 1.342 μm laser as the pump source of OPG.     

Judd-Oflet analysis of spectrum and laser performance of Ho：YAP crystal end-pumped by 1.91μm Tm：YLF laser

The Ho:YAP crystal is grown by the Czochralski technique.The room temperature polarized absorption spectra of Ho:YAP crystal was measured on a c cut sample with 1 at% holmium.According to the obtained Judd-Ofelt intensity parameters Ω2 = 1.42 × 10-20 cm2,Ω4 = 2.92 × 10-20 cm2,and Ω6 = 1.71 × 10-20 cm2,this paper calculated the fluorescence lifetime to be 6 ms for 5I7 →5 I8 transition,and the integrated emission cross section to be 2.24×10-18 cm2.It investigates the room temperature Ho:YAP laser end pumped by a 1.91 μm Tm:YLF laser.The maximum output power was 4.1 W when the incident 1.91 μm pump power was 14.4 W.The slope efficiency is 40.8%,corresponding to an optical to optical conversion efficiency of 28.4%.The Ho:YAP output wavelength was centred at 2118 nm with full width at half maximum of about 0.8 nm.