Investigations on order and width of RZ super Gaussian pulse in pre-, post- and symmetrical-dispersion compensated 10 Gb/s optical communication system using standard and dispersion compensating fibers

We show the effect of varied order and width of super Gaussian pulse at 10 Gb/s in dispersion compensated optical communication system. The optical communication system consists of standard single-mode fiber of 16 ps/nm/km of a certain length, whose dispersion is compensated using pre-, post- and symmetrical-dispersion compensation schemes with proportionate length dispersion compensating fiber of −80 ps/nm/km. Performance of these three compensation schemes is compared at 14 dBm values of Er-doped fiber amplifiers (EDFA) power at 1st, 2nd and 3rd order RZ super Gaussian optical pulse. The pulse width, full width at half maximum (FWHM) is also varied from 5 to 30 ps to highlight the optimum performance. The graphical results obtained show a relationship among the attributes pulse width, order of RZ super Gaussian optical pulse and dispersion compensation scheme implemented. It shows that to decrease BER and timing jitter in the system, smaller width and 3rd order super Gaussian pulse should be used. It is recommended that to decrease dependency of BER and timing jitter in the communication system on the pulse width i.e. FWHM, the symmetrical compensation scheme should be implemented.     

Impact of a Post-OTDM-Demultiplexing Optical Filter on Dense OOK OTDM-WDM Transmission

The impact of a post-OTDM-demultiplexing optical filter on the performance of dense on-off keying (OOK) optical time division multiplexing (OTDM)—wavelength division multiplexing (WDM) systems was studied. For return-to-zero (RZ) modulation, it was found that the additional filter working in a double-tier filter configuration did not offer any significant improvements to performance when the signal pulse width is optimized. Improvements generally increase only when the signal pulse width deviates from its optimal value and only for low spectral densities. For ideal non-return-to-zero (NRZ) modulation, however, significant improvements of around 1 dB are obtained using the double-tier configuration over a large range of spectral densities.     

Optimizing amplifier spacing to improve performance in RZ-rectangular pulse based 10 Gb/s single channel dispersion managed optical communication system

In this paper, we optimize the inter-amplifier spacing in combination with duty cycle of RZ data format and EDFAs power so that link length of system can be maximized. The results for EDFA amplifier placement in 10 Gbps single channel dispersion managed optical communication system have been presented. By increasing the length of standard single mode fiber of dispersion 16 ps/nm/km in proportion to the increase in length of compensating fiber of dispersion −80 ps/nm/km, the pre-, post- and symmetrical-dispersion compensation schemes of the system have been compared. Further, schemes are observed at 8, 10 and 12 dBm values of EDFA power in the link with different duty cycle values of RZ optical pulse in the range of 0.2-0.8 with step size of 0.2 in relation to amplifier spacing to get lower value of bit error rate and timing jitter. The graphical results obtained show strong relationship among duty cycle of RZ optical pulse, EDFA power and, dispersion compensation scheme.     

Optimal design of 32 channels spectrum slicing WDM for optical fiber access network system

In this article, the spectrum sliced dense wavelength division multiplexed passive optical network (SS-DWDM–PON) has been investigated as a power efficient and cost effective solution for optical access networks. In this work an AWG demultiplexer is used to operate as slicing system. The high speed SS-DWDM system has been realized and investigated for 32 channels with data rate up to 3 Gb/s using broadband ASE source (LED). The 3 Gb/s signals both non-return-to-zero (NRZ) and return-to-zero (RZ) were demonstrated in 40 km optical fiber link with BER < 10⁻¹². The results obtained here demonstrate that SS-DWDM is well suited for Fiber-to-the-Home (FTTH) network.     

Theoretical analysis of the all-fiberized, dispersion-managed regenerator for simultaneous processing of WDM channels

The concept of the all-fiberized multi-wavelength regenerator is analyzed, and the design methodology for operation at 40 Gb/s is presented. The specific methodology has been applied in the past for the experimental proof-of-principle of the technique, but it has never been reported in detail. The regenerator is based on a strong dispersion map that is implemented using alternating dispersion compensating fibers (DCF) and single-mode fibers (SMF), and minimizes the nonlinear interaction between the wavelength-division multiplexing (WDM) channels. The optimized regenerator design with + 0.86 ps/nm/km average dispersion of the nonlinear fiber section is further investigated. The specific design is capable of simultaneously processing five WDM channels with 800 GHz channel spacing and providing Q-factor improvement higher than 1 dB for each channel. The cascadeability of the regenerator is also indicated using a 6-node metropolitan network simulation model.     

Cross-phase modulation induced phase fluctuations in optical RZ pulse propagating in dispersion compensated WDM transmission systems

The basic mechanism of cross-phase modulation induced phase fluctuations in optical RZ pulse propagating in a periodically dispersion compensated transmission line has been investigated. Ordinary differential equations have been derived using variational analysis to estimate the phase fluctuation and the analytical result is verified by numerical simulations based on split-step Fourier method. We therefore explore the impact of different dispersion compensation maps on phase fluctuation for 10 Gb/s and 40 Gb/s WDM transmission systems. The effects of initial pulse spacing between channels, channel spacing and residual dispersion on phase shift have been studied. We find that cross-phase modulation induced phase fluctuation can be mitigated by proper adjustment of channel spacing and/or residual dispersion.     

On duty cycle selection of RZ optical pulse to optimize the performance of dispersion compensated 10 Gbps single channel optical communication system using dispersion compensating fibers

We present results for duty cycle selection of optical RZ pulse to optimize the performance in 10 Gbps single channel dispersion compensated optical communication system. The system has link length of 240 km with two spans. Each of the spans consists of 120 km standard single mode fiber (SSMF) of 16 ps/nm/km, whose chromatic dispersion is compensated using pre-, post- and symmetrical-dispersion compensation schemes by 24 km dispersion compensating fiber (DCF) of −80 ps/nm/km. The performance of the three compensation schemes is compared by taking 8, 10, 12 and 14 dBm Er-doped fiber amplifier (EDFA) power levels in the link with a duty cycle range (0.1-0.9) of RZ optical pulse. The graphical results obtained show a relationship among the duty cycle, EDFA power and dispersion compensation scheme which predicts the best performing duty cycle case. To optimize performance of the system, we recommend in general, duty cycle less than 0.3 and EDFA power below 8 dB irrespective of compensation scheme. However, with post compensation duty cycle less than 0.7 and EDFA power below 12 dBm give optimum performance. The results conclude that for the high value of duty cycle, post dispersion compensation scheme should be used.     

Reduction in timing jitter by chirp selection for externally modulated return to zero optical soliton pulse at 10 Gb/s

We investigate the chirp selection of externally modulated RZ soliton pulse at 10 Gb/s for fiber optical communication systems for the reduction in timing jitter. We have chosen single arm Mach-Zehnder amplitude modulator with sin² electrical shaped input-output (P-V) characteristic and its chirp range has been varied in the range of −5 to 5. The timing jitter, Q factor and bit error rate (BER) generated for the chirp range has been studied for various fiber lengths and post compensation has been demonstrated to reduce the timing jitter. The number of fixed output amplifiers after every 60 km span is varied from 2 to 10 and corresponding accumulated ASE noise has been studied to manage timing jitter and BER in permissible range, i.e. 5 ps and 10⁻⁹, respectively. It is observed that when two fiber spans are taken then the compensating fiber length for the system is less than 20 km for each case of the chirp considered. For 10 fiber spans, the compensating fiber length increases in the range 60-90 km depending upon the value of chirp taken. Finally it is shown that the chirp value of external modulator should be set to either 0 or −1 for externally modulated RZ soliton pulse in 10 Gb/s optical communication system which makes the system more insensitive to the timing jitter and the selection of dispersion compensating fiber length.     

Performance analysis of optical WDM system based on unequal spaced channel allocation (USCA) scheme

Unequal spaced channel allocation (USCA) is a technique to reduce Four wave mixing (FWM). In this paper, system performance of 8 channel WDM system considering different optical transmitter formats (RZ, NRZ, Raised cosine and Gaussian) using USCA has been evaluated in terms of Q-factor. The simulation results reveal that four wave mixing is minimum for NRZ format. Also the effect of changing the laser power and increasing the bit rate has been observed.     

The effects of different dispersion compensation ratios on nonlinear single channel and WDM systems

The effects of the compensation ratio with dispersion post-compensation on nonlinear single channel and WDM systems with 10 Gb/s per channel are numerically investigated. When the transmission signal per channel is 10 Gb/s RZ pulse and the amplifier span is 50 km, proper undercompensation can enhance the performance of the nonlinear single channel system and the nonlinear WDM system. But the enhanced distance of the nonlinear WDM system is not as obvious as that of the single channel system, because the cross-phase-modulation effect plays an important role in the nonlinear WDM system.     

Generation, detection and characterization of optical minimum shift keying data format

This paper presents the detailed principle on the generation and detection of optical minimum shift keying (MSK) format for high-speed and high spectral efficiency WDM systems. 10.7 Gb/s optical MSK data is successfully generated by experiment using the proposed scheme. The results show that optical MSK signal exhibits very compact optical spectrum, which is promising for high spectral efficiency WDM applications. Simulation results on dispersion and nonlinear tolerance comparison confirm that MSK signal has better dispersion tolerance and nonlinear tolerance compared with 50% duty cycle return-to-zero differential phase shift keying (RZ-DPSK) and 50% duty cycle RZ on-off-keying (RZ-OOK) formats.     

Simulation of DWDM signals using optimum span scheme with cascaded optimized semiconductor optical amplifiers

We numerically simulated the ten channels at 10 Gb/s dense wavelength division multiplexing (DWDM) transmission faithfully over 17,227 km using 70 km span of single mode fiber (SMF) and dispersion compensating fiber (DCF) using optimum span scheme at channel spacing 20 GHz. For this purpose, inline optimized semiconductor optical amplifiers (SOAs) and DPSK format are used. We optimized the SOA parameters for inline amplifier with minimum crosstalk and amplified spontaneous emission noise with sufficient gain at bias current 400 mA. For this bias current, constant gain 36.5 dB is obtained up to saturation power 21.35 mW. We have also optimized the optical phase modulator bandwidth for 400 mA current which is around 5.5 GHz with crosstalk −14.2 dB between two channels at spacing 20 GHz.We show the 10×10 Gb/s transmission over 70 km distance with inline amplifier has good signal power received as compared to without amplifier, even at equal quality factor. We further investigated the optimum span scheme for 5670 km transmission distance for 10×10 Gb/s with channel spacing 20 at 5.5 GHz optical phase modulator bandwidth. As we increase the transmission distance up to 17,227 km, there is increase in power penalty with reasonable quality.The impact of optical power received and Q factor at 5670 and 17,227 km transmission distance for different span schemes for all channels has been illustrated. For launched optical power less than saturation, all channels are obtained at bit error rate floor of 10⁻¹⁰.     

Optimum algorithm for WDM channel allocation for reducing four-wave mixing effects

A novel channel allocation method, based on optical Golomb ruler (OGR), that allows reduction of the FWM effect while maintaining bandwidth efficiency along with the algorithms has been presented in this paper. Very high-capacity, long-haul optical communication systems can be designed by wavelength division multiplexing (WDM) of high-bit-rate channels and by using erbium-doped fiber amplifiers (EDFAs) to periodically compensate the fiber loss. In such all-optical systems, the effects of chromatic dispersion and nonlinearities accumulate during light propagation, imposing limits on the achievable performance. Chromatic dispersion at 1.55 pm can be effectively reduced by using dispersion-shifted fiber (DSF). The use of very-low-dispersion fiber, however, enhances the efficiency of generation of four-wave mixing (FWM) waves by reducing the phase mismatch naturally provided by the fiber dispersion. For this reason, crosstalk due to FWM is the dominant nonlinear effect in long-haul WDM systems using DSFs. To reduce four-wave-mixing crosstalk in high capacity long-haul repeater less WDM light wave systems, the use of the channel allocation method that involves unequal spaced channels has been proposed.     

Comparative investigation and suitability of various data formats for 10 Gb/s optical AWG multiplexer and AWG demultiplexer based transmission links

In this paper, we have analyzed the performance and feasibility for the metropolitan area network based on arrayed waveguide grating (AWG) multiplexers and arrayed waveguide grating (AWG) demultiplexers operating at the bitrate of 10 Gb/s. In the network, the data is successfully transmitted to a distance of 50 km with a very low BER of 1 × 10⁻⁴⁰ thus improving the performance over AWG star based networks. Here, we have observed that arrayed waveguide gratings based multiplexers and demultiplexers for WDM applications prove to be capable of precise multiplexing and demultiplexing of a large number of channels with relatively low losses. This paper also presents the comparative investigation and suitability of various data formats like NRZ Rectangular, NRZ Raised cosine, RZ Rectangular, RZ Raised cosine and RZ super Gaussian for optical transmission link. It has been shown that RZ Raised cosine yields the highest value of Q, good eye opening and lowest BER.     

Dispersion characteristic of hexagonal and square lattice chalcogenide As2Se3 glass photonic crystal fiber

In this paper, we report a chalcogenide As₂Se₃ glass photonic crystal fiber (PCF) for dispersion compensating application. We have used the improved fully vectorial effective index method (IFVEIM) for comparing the dispersion properties (negative and zero dispersion) and effective area in hexagonal and square lattice of As₂Se₃ glass PCF using different wavelength windows. It has been demonstrated that due to their negative dispersion parameter and negative dispersion slope in wavelength range 1.2-2.5 μm, both lattice structures of As₂Se₃ glass PCFs, with pitch (Λ = 2 μm), can be used as dispersion compensating fibers. Further, design parameters have been obtained to achieve zero dispersion in these fibers. It is also shown that As₂Se₃ glass PCF provides much higher negative dispersion compared to silica PCF of the same structure, in wavelength range 1.25-1.6 μm and hence such PCF have high potential to be used as a dispersion compensating fiber in optical communication systems.     

20GHz注入锁模光纤激光器实验

稳定、波长可调谐的窄脉冲光源是未来光时分复用/波分复用光纤通信系统的重要组成部分。报道了一个20GHz的注入锁模光纤激光器的实验。利用一个10GHz的导体体激光器作为光源，最终得到了波长可调谐的重复频率为20GHz、脉冲宽度为12.4ps的光脉冲，波长的调谐范围为16nm。     

Timing jitter induced by intrachannel interactions in optical fiber communication systems using CFG as dispersion compensator

In this paper, a theoretical model is proposed for the analysis of timing jitter induced by intrachannel interactions in optical fiber communication systems using chirped fiber grating (CFG) as dispersion compensator. And for the first time, the impact of group-delay ripple (GDR) on timing jitter is taken into account in detail, theoretically and numerically. Results show that the GDR may increase or decrease the timing jitter of certain pair of adjacent pulses, deciding by the ripple parameters. The maximum influence will be obtained when ripple period is about 2/5 of the input pulse width. In practical systems, the GDR enhance the timing jitter for some adjacent pulses while reduce it for some other adjacent pulses, depending on the pulse pattern and the GDR parameters. In our simulation, the GDR guarantees a 3.04 ps increase of the standard deviation of the timing jitter.     

Comparative investigation and suitability of various data formats for 10 Gb/s optical soliton transmission links at different chirps

This paper presents the comparative investigation and suitability of various data formats for optical soliton transmission links at 10 Gb/s for different chirps (−0.7 to 0.7). Here the investigations focused on data formats: NRZ, RZ soliton, RZ raised cosine and RZ super Gaussian. The comparative results and suitability of data formats is based on various performance measures such as Q-factor, eye opening, BER and jitter. It has been indicated that RZ super Gaussian yields the highest value of Q (34.08 dB), good eye opening and lowest BER.     

Microstructure holey fibers as wideband dispersion compensating media for high speed transmission system

This paper presents a dispersion compensating microstructure holey fiber for wideband transmission system. The finite element method with perfectly matched absorbing layers boundary condition is used to investigate the guiding properties. According to simulation, negative dispersion coefficient of −1455 ps/(nm km) and a relative dispersion slope (RDS) close to that of single mode fiber of about 0.0036 nm⁻¹ is obtained at 1.55 μm. The variation of structural parameters is also studied to evaluate the tolerance of the fabrication. The proposed module can be used in 40 Gb/s dense wavelength division multiplexing (DWDM) systems in optical fiber communication networks.     

Investigation of wavelength division multiplexing ring network topology to enhance the system capacity

In this paper, we have investigated the wavelength division multiplexed (WDM) system using ring network topology. This network is used to increase the capacity with eight optical add/drop multiplexers (OADMs) by using dispersion compensating fiber and semiconductor optical amplifier (SOA) to achieve a distance up to 1600 km. It is observed that network shows the acceptable results at 15 Gbps data rate with 100 GHz channel spacing. The OADM nodes are also varied to investigate the network performance in the term of BER and Q-factor.