Impact of optical modulation formats on SPM-limited fiber transmission in 10 and 40 Gb/s optimum dispersion-managed lightwave systems

In this paper, 10 and 40 Gb/s optical systems have been investigated for nonreturn-to-zero (NRZ), return-to-zero (RZ), carrier-suppressed return-to-zero (CSRZ) and RZ-differential phase-shift-keying (RZ-DPSK) data formats. For the range of the optical signal power from −5 to 15 dBm, a maximum self-phase modulation (SPM)-limited transmission distance L_SPM is determined with eye-opening penalty (EOP) >1 dB .The observations are based on the modeling and numerical simulation of optimum dispersion-managed transmission link. Transmission over distances of the order of several hundreds of kilometers has been shown with and without amplified spontaneous emission (ASE) noise of the in-line erbium-doped fiber amplifiers (EDFAs).     

Performance analysis of NRZ, RZ, CRZ and CSRZ data formats in 10 Gb/s optical soliton transmission link under the impact of chirp and TOD

This paper presents the performance analysis of non-return-to-zero (NRZ), return-to-zero (RZ), chirped return-to-zero (CRZ) and carrier suppressed return-to-zero (CSRZ) data formats in optical soliton transmission link under the impact of chirp and third-order dispersion (TOD). The performance of these data formats has been analyzed on the basis of certain performance metrics, viz, bit error rate (BER), Q² (dB), OSNR, eye opening, etc. It has been reported here that the performance of CRZ and CSRZ modulation format is better as compared to NRZ and RZ in a soliton transmission link. Further, CSRZ modulation format has been found to deliver optimum performance on the basis of performance evaluation metrics reported in this paper. In case of NRZ and CSRZ, comparatively narrow power spectrum has been observed. Best eye opening, highest value of Q² (dB) of 18 dB and lowest value of BER of the order of 10⁻¹⁶ has been reported in case of CSRZ among the considered data formats. The results have been obtained by varying noise figure from 3.0 to 9.0. No considerable effect of noise was observed. It was observed that at very narrow and ultra short pulse width, OSNR value suffers heavily and reduced to even negative values in dB, thus inducing a high degree of OSNR power penalty. The results were obtained by varying chirp factor from −0.6 to +0.6. Negative chirp resulted in improved OSNR as compared to positive chirp. RZ data format yielded a broader optical spectrum, comparatively low spectral efficiency and poor OSNR thus it was found that RZ format is not suitable for optical soliton transmission under the impact of chirp and TOD.     

Analysis of modulation format in the 40 Gbit/s optical communication system

Three different modulation formats including nonreturn-to-zero (NRZ), return-to-zero (RZ), carrier-suppressed return-to-zero (CS-RZ) and the differential phase keying (DPSK) modulation format of each code are introduced in the article. A method of their modulated signal generation with computer is described, and a comparison of their spectra and waveforms is made. The 40 Gbps signal transmitted in 200 km G.652 fiber by way of single channel with erbium-doped-fiber-amplifier (EDFA) is simulated for these three formats. The ability of anti-dispersion and anti-PMD is analyzed. It is shown that RZ and CS-RZ formats are more tolerant than NRZ format in the same conditions.     

Transmission performance of 20 × 10 Gb/s WDM signals using cascaded optimized SOAs with OOK and DPSK modulation formats

We investigated 20 channels at 10 Gb/s wavelength division multiplexing (WDM) transmission over 1190 km single mode fiber and dispersion compensating fiber using cascaded inline semiconductor optical amplifier at a span of 70 km for RZ-DPSK (return zero differential phase-shift keying) modulation format by using same channel spacing, i.e. 100 GHz. We show for RZ-OOK (return zero on-off keying) format a transmission distance of up to 1050 km with Q factor more than 15 dB, without any power drops. We developed the SOA model for inline amplifier having minimum cross-talks and ASE (amplified spontaneous emission) noise power with sufficient gain. At optimal bias current of 400 mA, a high constant gain of 36.5 dB is obtained up to a saturation power of 21.36 mW. So reduction of cross-talk and distortion is possible by decreasing the bias current at appropriate amplification factor.The DPSK modulation format has less cross-talk as compared to OOK format for nonlinearities and saturation case. The impact of optical power received and Q factor at different distance for both RZ-OOK and RZ-DPSK modulation format has been illustrated. We have shown the optical spectrum and clear Eye diagram at the transmission distance of 1190 km in RZ-DPSK system and 1050 km in RZ-OOK systems.The bit error rate (BER) for all channels observed is less than 10⁻¹⁰ up to gain saturation for both DPSK and OOK systems. Finally, we investigated that the transmission distance decreases with a decrease in channel spacing of up to 20 GHz.     

Analysis of 2.5 Gbit/s GPON downlink optical-receiver performance

In the gigabit-capable passive optical network (GPON) optical communication system, the selection of fiber and system performance-analysis is the key links for the realization of system function. Especially the characteristic budget and parameter setting of downlink receiver are topped the list. The analysis of receiver power penalty can reduce the influence on receiver sensitivity and bit error rate (BER) that caused by waveguide dispersion and pulse widening. This article will simulate the performance of GPON downlink receiver, then analyze typical characteristics such as Four Wave Mixing (FWM), Erbium-Doped Fiber Amplifier (EDFA), system eye pattern and Q factor and so on, so as to validate the feasibility of the optical downlink.     

Performance analysis of different modulation formats in 4-channel CATV transmission system using OADM

In this paper we have analyzed the performance of different modulation formats for a four-channel WDM CATV system using optical ad drop multiplexers and the impact of frequency and wavelength on Q-value, and eye opening is observed for added and dropped channels at different lengths.     

Comparative investigation and suitability of various data formats for 10 Gb/s optical soliton transmission links at different chirps

This paper presents the comparative investigation and suitability of various data formats for optical soliton transmission links at 10 Gb/s for different chirps (−0.7 to 0.7). Here the investigations focused on data formats: NRZ, RZ soliton, RZ raised cosine and RZ super Gaussian. The comparative results and suitability of data formats is based on various performance measures such as Q-factor, eye opening, BER and jitter. It has been indicated that RZ super Gaussian yields the highest value of Q (34.08 dB), good eye opening and lowest BER.     

Impact of extinction ratio of single arm sin LiNbO3 Mach-Zehnder modulator on the performance of 10 and 20 Gb/s NRZ optical communication system

We investigate the impact of extinction ratio of single arm sin² LiNbO₃ Mach-Zehnder (MZ) amplitude modulator on the performance of 10 and 20 Gb/s single-channel optical communication system. For different fiber lengths, the system performance has been analyzed with the increase in the extinction ratio. The effect of variation in dispersion parameter has also been illustrated. The impact of extinction ratio (ζ), dispersion parameter and length of the fiber has been further optimized with minimum bit error rate (BER) at optimal decision threshold (10⁻⁹) for 10 and 20 Gb/s bit rate. It is found that the system gives optimum performance at extinction ratio (ζ) value 20 dB. The increase in the transmission distance from 468 km for 10 Gb/s to 532 km for 20 Gb/s has been reported, and 8 dB improvement in the Q value has been observed as the value of ζ is increased from 10 to 20 dB. At 20 Gb/s, the system gives optimum performance for dispersion parameter value only up to 4 ps/nm km; however, at 10 Gb/s the system can operate for dispersion values up to 14.3 ps/nm km. Further we investigate the self-phase modulation (SPM) effect for the increase in the input power. It is observed that the SPM effect is negligible below 3 dB m input power and it increases at higher power levels.     

Implementation and performance analysis of three dimensional (3D) space/wavelength/time single pulse per plane codes with direct detection

In this paper, we present space/wavelength/time single pulse per plane (SPP) codes with direct detection (SPPDD) and implemented it as two dimensional codes by using W²T scheme. We analyze these codes by varying the number of space channels (S) and keeping other two dimensions, wavelength (W) and time (T) constant and report that it gives better results when (W > S). It is found that the space channels S = 2 and S = 3 provide better BER rate than other space channels and also analyze these 3D codes by using different data modulation formats. It is found that OCDMA system with NRZ data modulation format performs better than RZ.     

10 and 20 Gb/s all-optical RZ to NRZ modulation format and wavelength converter based on nonlinear optical loop mirror

We present experimental and theoretical results on all-optical 10 and 20 Gb/s RZ to NRZ modulation format and wavelength converter based on a nonlinear optical loop mirror (NOLM). A vector model of converter was developed and the shape of converted pulses was found analytically for particular choice of polarization states. In the experiment, non-zero dispersion shifted fiber with a length 1200 m was used as a nonlinear medium. Pulses from a 10 GHz mode-locked semiconductor laser diode were modulated to form pseudorandom RZ signal and eventually time division multiplexed to 20 Gb/s. RZ pulses were subsequently converted to NRZ signal. The performance of the converter was evaluated experimentally using the data communication analyzer and bit error ratio tester.     

Simulation of Fiber to the Home at 10 Gbit/s using GE-PON architecture

In this paper, a fiber communication system is employed using Giga Ethernet Passive Optical Network (GE-PON) architecture. In this architecture an optical fiber is employed directly from a Central Office to the home. A 1:8 splitter is used as a PON element which establishes communication between a Central Office to different users. The architecture has been investigated for different lengths from a Central Office to the PON in terms of BER. For 10 Gbit/s system the plots between the BER and transmission distance are plotted and it are seen that as the distance increases beyond the 15 km the BER is increased very sharply. The results in the form of voice and data spectrum for different users of FTTH with GE-PON architecture are shown.     

Performance analysis and improvement of spectrally amplitude encoded/decoded OCDMA system

This paper describes a performance analysis of an incoherent optical code-division multiple-access scheme based on wavelength/time (W/T) codes. The system supports 16 users operating at 2.5Gb/s/user while maintaining bit-error rate (BER) < 10⁻¹¹ for the correctly decoded signal. It has been observed that there are two major problems giving rise to performance degradation of the system in terms of number of users and type of code.In this paper we have studied the optical simulator Encoding/Decoding for different lengths & gain in terms of Quality factor (Q) and Bit Error Rate (BER) performance. The system supports 16 users while maintaining bit-error rate (BER) < 10⁻¹¹ for the correctly decoded signal. Our aim is to design and simulate a Tree Network Topology Optical Code Division Multiple Access System for large number of users using wavelength–time code and to analyze the performance of the system based on BER and Eye Diagram under the influence of number of simultaneous users with different received powers.     

Transmission of 4× 40/10 Gbps in a WDM-PON using NRZ-DQPSK/ASK modulation

In this paper we demonstrate the feasibility to deploy a wavelength division multiplexing passive optical network (WDM-PON) of a 30 km standard single-mode fiber (SSMF-28) carrying 160 Gbps data in downstream and 40 Gbps through the uplink. The developed method is based on the comparison between two WDM-PON systems of 4 channels with the same characteristics, using two different formats of modulation in OLTs. The first system uses the NRZ-ASK in the downlink direction, while the second uses the NRZ-DQPSK.     

Investigations on order and width of RZ super Gaussian pulse in different WDM systems at 40 Gb/s using dispersion compensating fibers

In optical wavelength division multiplexed (WDM) systems the dispersion management is a key issue. In optical systems a lot of research is going on to reduce dispersion by selecting proper dispersion compensating techniques and proper modulation format for input data. One way to reduce dispersion is by using dispersion compensating fibers in the WDM systems. This paper analyzes the use of RZ super Gaussian pulse inputs for different WDM systems i.e. for conventional, dense and ultra dense WDM systems employing dispersion compensating fibers. The pulse width and the order of the RZ super Gaussian pulse was varied to evaluate the performance at 40 Gb/s. The experiment showed that to get minimum BER, pulse width of 7.5 ps and 10 ps along with third-order RZ super Gaussian pulse were found suitable and recommended to be used.     

Numerical analysis and system optimization for 100 Gbit/s carrier Ethernet serial modulation formats

The performance of various modulation schemes for 100 Gbit/s single-channel serial transmission is investigated by means of numerical simulations. Different ASK and PSK modulation formats are compared in terms of total system reach for a 10⁻⁹ BER requirement. RZ-DQPSK format with a 1920 km reach, without FEC and without the support of additional Raman amplification, outperforms all the other schemes including 10 × 10 Gbit/s NRZ DWDM inverse multiplexing.     

160 Gbps S-band WDM transmission system over 1400 km using ITUT-652a and ITUT-655 fibers with low dispersion accumulation

Dispersion accumulation with the distance effects optical WDM system's performance severely. For every modulation format used there is a limit on maximum transmission distance due to dispersion accumulation. So dispersion compensation is required. But dispersion compensation can be avoided to a large extent by alternatively using different fiber standards. In this paper it has been proposed that the dispersion accumulation can be reduced to a large extent by alternatively transmitting in S-band and using fiber standards ITUT-652a and ITUT-655. To validate the claim, performance of a 16 channel 10 Gbps WDM system with the proposed method has been analyzed in terms of BER and Q-factor. And it has been observed that with the proposed scheme without any dispersion compensation the system performs well up to 1400 km.     

Optimizing 10 Gbps optical communication system with duty cycle selection of return to zero pulse

We have investigated the return-to-zero (RZ) pulse duty cycle for single-channel Standard Single mode fiber (SSMF), Non Zero Dispersion shifted fibers (normal NZDSF and anomalous NZDSF fiber) for 10 Gbps optical fiber communication system. We give a comprehensive look on the behavior of variable duty cycle optical RZ pulse indicating that lowest bit error rate for duty cycle 0.8 among the duty cycle values 0.2, 0.4, 0.6 and 0.8 investigated for the case of SSMF. The single repeaterless mode fiber length is increased from existing 55 km at duty cycle 0.2 to fiber length 85 km by keeping duty cycle at 0.8. The result is also emphasized through the 10 dB Q value improvement and corresponding improvement in average eye opening diagram. The normal NZDSF show similar improvement but at greater fiber length, it offers BER 10⁻⁹ at length 110 km with duty cycle 0.2. NZDSF operating length can further be increased to length 160 km by keeping duty cycle 0.8. The corresponding 8 dB Q value improvement and Average eye opening improvement also supports the result through its graphical variation. Thirdly Anomalous NZDSF for same optical communication system showed that 0.2 duty cycle value give operational length of 130 km which could be extended to 160 km if 0.8 duty cycle is kept. The corresponding 8 dB Q value improvement, average eye-opening improvement endorsed the fact in the graphs.     

Comparative investigation and suitability of various data formats for 10 Gb/s optical AWG multiplexer and AWG demultiplexer based transmission links

In this paper, we have analyzed the performance and feasibility for the metropolitan area network based on arrayed waveguide grating (AWG) multiplexers and arrayed waveguide grating (AWG) demultiplexers operating at the bitrate of 10 Gb/s. In the network, the data is successfully transmitted to a distance of 50 km with a very low BER of 1 × 10⁻⁴⁰ thus improving the performance over AWG star based networks. Here, we have observed that arrayed waveguide gratings based multiplexers and demultiplexers for WDM applications prove to be capable of precise multiplexing and demultiplexing of a large number of channels with relatively low losses. This paper also presents the comparative investigation and suitability of various data formats like NRZ Rectangular, NRZ Raised cosine, RZ Rectangular, RZ Raised cosine and RZ super Gaussian for optical transmission link. It has been shown that RZ Raised cosine yields the highest value of Q, good eye opening and lowest BER.     

Structure analysis of stoichiometric LiNbO3(0 0 0 1) surfaces using low-energy neutral scattering spectroscopy

The atomic structure of LiNbO₃(0 0 0 1) surface was investigated by low-energy neutral scattering spectroscopy (LENS). Poled stoichiometric LiNbO₃ (SLN) samples were prepared for the measurements. The LENS was developed for surface structure and composition analysis particularly of highly insulating materials and was successfully applied to the structure analysis of the SLN(0 0 0 1) surface. The polar angle dependences of intensity of scattered He⁰ from the poled SLN surfaces indicate obvious differences between the negatively and the positively charged surfaces. It is suggested that O atoms cover the surfaces, and the first metal layers underneath the O layer consist of Li and Nb for negatively and positively charged surfaces, respectively, parallel to the applied electric field.     

Effectiveness of electronic equalizer for filter concatenation effect of low-cost 2.5 Gb/s rated DML sources operated at 10 Gb/s

The improvement on the impact of filter concatenation effect on optical signal quality is investigated and discussed for applications in metropolitan optical networks utilizing cost-effective 10-Gb/s transmitters. The sources are low-cost conventional directly modulated lasers (DMLs), fabricated for operation at 2.5 Gb/s but modulated at 10 Gb/s. Performance improvement is achieved by using decision-feedback equalization (DFE) at the receiver end. Experimental studies consider both transient and adiabatic chirp dominated DMLs sources with different chirp characteristics. Measurements have been obtained using a recirculating loop set-up and the performance improvement is evaluated in terms of bit-error-rate (BER) versus number of loops.