Analysis of propagation characteristics for an octagonal photonic crystal fiber (O-PCF)

An octagonal photonic crystal fiber (O-PCF) structure with eight air-holes on the first ring is proposed based on a unit isosceles triangle. The propagation characteristics and cut-off behaviors of the O-PCF and the standard hexagonal PCF (H-PCF) are numerically investigated by combining the vector boundary method and the effective area method. The phase boundaries for cut-off, single-mode, and multi-mode operations between the O-PCF and H-PCF are calculated and compared. It is found that under the same pitch Λ and air filling fraction (AFF) of the air-holes the O-PCF has significantly wider wavelength range operating in single-mode region, more circular-like field distribution, and less confinement loss than the H-PCF.     

Design procedure for photonic crystal fibers with ultra-flattened chromatic dispersion

A simple design procedure is used to generate photonic crystal fibers (PCFs) with ultra-flattened chromatic dispersion. Only four parameters are required, which not only considerably saves the computing time, but also distinctly reduces the air-hole quantity. The influence of the air-hole diameters of each ring of hexagonal PCFs (H-PCF, including 1-hole-missing and 7-hole-missing H-PCFs), circular PCFs (C-PCF), square PCFs (S-PCF), and octagonal PCFs (O-PCF) is investigated through simulations. Results show that regardless of the cross section structures of the PCFs, the 1st ring air-hole diameter has the greatest influence on the dispersion curve followed by that of the 2nd ring. The 3rd ring diameter only affects the dispersion curve within longer wavelengths, whereas the 4th and 5th rings have almost no influence on the dispersion curve. The hole-to-hole pitch between rings changes the dispersion curve as a whole. Based on the simulation results, a procedure is proposed to design PCFs with ultra-flattened dispersion. Through the adjustment of air-hole diameters of the inner three rings and hole-to-hole pitch, a flattened dispersion of 0±0.5 ps/(nm·km) within a wavelength range of 1.239 – 2.083 μm for 5-ring 1-hole-missing H-PCF, 1.248 – 1.992 μm for 5-ring C-PCF, 1.237 – 2.21 μm for 5-ring S-PCF, 1.149 – 1.926 μm for 5-ring O-PCF, and 1.294 – 1.663 μm for 7-hole-missing H-PCF is achieved.     

扩散序谱(DOSY)实验中扩散系数维数字分辨率的影响

核磁共振二维扩散序谱（DOSY）实验测定溶液中分子自扩散系数时,扩散系数维的数据点及其数字分辨率直接影响了测定值的精度.在较系统地确定了DOSY实验本身偏差范围的基础上,本文研究了扩散系数维不同的数字分辨率对测定值的影响,包括其引入偏差的来源以及形成偏差的大小.由于不同的溶液条件下分子扩散系数的改变可直接用于表征分子结构或状态的变化,本文提出的相对数字分辨率与扩散系数相对变化值的直接比较,可直观地表明数字分辨率对扩散系数测定值的影响.     

Dispersion and Confinement Loss Control in Modified Hexagonal Photonic Crystal Fibers

This paper presents a novel technique for the control of chromatic dispersion and confinement loss in hexagonal photonic crystal fibers (H-PCFs). It is demonstrated that it is possible to obtain very low chromatic dispersion of 0 ± 0:38 ps/(nm·km) in the wavelength range of 1.41 to 1.66 μm and confinement loss of less than 0.0001 dB/km from a six ring modified H-PCF (MH-PCF). The higher order dispersion at 1.55 μm is about −0.001 ps/(nm²-km).     

激光热透镜光谱法测量有机溶剂的弱吸收

本工作采用反向交叉式双光束激光热透镜光谱法,以氩离子激光作泵浦光源,在514.5nm波长条件下,测量了十五种有机溶剂和水的极小的吸收系数,获得了较高的测量灵敏度。洋细研究了基本实验参数,讨论了光路系统,讨论和比较了测量各类有机溶剂的吸收系数实验结果。     

用于双色全息存储（Fe，Cu）：LiNbO3晶体的参量优化计算

在确定Cu在LiNbO3晶体中对应于365nm和633nm的激发系数、复合系数、光伏系数的基础上，采用龙格-库塔（Runge-Kutta）数值方法理论研究了双掺杂（Fe，Cu）：LiNbO3晶体的深浅能级的掺杂组分比、氧化-还原状态对双色全息存储的记录灵敏度和动态范围的影响，并探讨了同时取得尽可能大的灵敏度和动态范围的晶体条件。结果表明，为了同时得到较大的记录灵敏度和动态范围，在实际应用中选用浅能级掺杂浓度为5．0×10^25m^-3，深能级掺杂浓度为3×10^24～3×10^25m^-3之间的弱氧化晶体是合适的。     

Thermal expansion in various phases of Nitinol using TMA

Phase transformation in the near-equiatomic, cold-worked Nitinol, exhibiting shape memory effect, has been investigated through the study of thermal expansion by employing thermomechanical analyser (TMA). The characteristic transformation temperatures determined by this method are compared with those obtained through DSC thermograms. The reliability and sensitivity of the thermal expansion probe have been discussed. The variation of thermal expansion coefficient with temperature in different heat treated samples has been studied in the range 30–120°C. Thermal expansion coefficient is found to be −ve during M↔A transformation and +ve in R↔A transformations. Thermal expansion coefficient in martensitic region in the presence and absence of R-phase has been determined.     

风力机叶片21%相对厚度翼型粗糙敏感性研究

基于变速变桨水平轴风力机,依据动量叶素理论和风力机实例,分析得出了叶片外侧翼型(包括21%相对厚度翼型)在低于额定风速变速运行阶段的粗糙敏感性评价指标为升力系数和升阻比的下降率;提出了根据升、阻力系数对输出功率的作用大小来确定两粗糙敏感性评价指标权重系数的方法,并用实例演示了21%相对厚度翼型粗糙敏感性评判基准的获得;另外,通过正交设计、XFOIL软件几何造型与气动计算和方差分析得出了翼型各几何参数在不同雷诺数下对粗糙敏感性不同评价指标的影响程度和最优组合是不一样的。本文结论可为不同风况下风力机翼型的设计和粗糙敏感性评价提供参考。     

用于液体传感的高双折射新型光子晶体光纤结构

提出一种用于液体传感的光子晶体光纤的结构和设计方法。将六边形光子晶体光纤的纤芯区域设计成2个椭圆空气孔,分别填充水和乙醇,进而比较两种光子晶体光纤结构的传播特性。采用全矢量有限元法对所设计光子晶体光纤结构的双折射、相对灵敏度、限制损耗、非线性系数进行数值分析,对光纤各项参数的优化及纤芯椭圆结构参数进行调整,结果表明:当椭圆率为0.6时,纤芯填充乙醇的光子晶体光纤PCF2在波长1.55 nm处相对敏感度可达到72.506 7%,同时限制损耗可以降至10?8级。所设计的模型可用于传感和生物传感研究及应用。     

热光系数与长周期光纤光栅的温度灵敏度研究

利用受温度影响的光纤的本征方程和相位匹配条件,从理论上研究了长周期光纤光栅(LPFGs)的温度响应特性,给出了LPFGs的温度灵敏度的解析表达式。对利用低模序包层模的LPFG进行了实验研究。结果表明,利用不同包层模的LPFGs具有不同的温度灵敏度。分析了光纤的材料热光系数和模的热光系数的差别。单模光纤导模的热光系数接近纤芯的材料热光系数,而包层模的热光系数比包层的材料热光系数大,模序越大,其值越大。适当调整纤芯和包层的热光系数,并选用不同的包层模,可以得到对温度灵敏或不灵敏的LPFGs。     

行波半导体光放大器的偏振特性研究

以有源法布里－珀罗谐振腔的增益特性为基础，研究了行波半导体光放大器的偏振特性。对行波半导体光放大器的偏振灵敏度与端面反射率、增益系数、光场限制因子等诸因素之间的关系进行了理论分析和实验研究。在此基础上，讨论了改善行波半导体光放大器偏振灵敏度的若干方法，并提出了新的偏振不灵敏行波半导体光放大器结构。     

Irradiation effect on strain sensitivity coefficient of strain sensing fiber Bragg gratings

The effect of irradiation on the strain sensitivity coefficient of strain sensing fiber Bragg gratings(FBGs) has been investigated through experiments. FBGs were fabricated in single mode fibers with 3 mol% Ge-concentration in the core and with a H2-loading treatment. In experiments, the FBGs were subjected to γ-radiation exposures using a Co60 source at a dose-rate of 25 Gy/min up to a total dose of 10.5 kGy. The GeO defect in fiber absorbs photons to form a GeE’ defect; the interaction with H2 is a probable reason for the γ-radiation sensitivity of gratings written in hydrogen loaded fibres. The effect mechanism of radiation on the strain sensitivity coefficient is similar to that of radiation on the temperature sensitivity coefficient. Radiation affects the effective index neff, which results in the change of the thermo-optic coefficient and the strain-optic coefficient. Irradiation can change the strain sensitivity coefficient of FBGs by 1.48%–2.71%, as well as changing the Bragg wavelength shift(BWS) by 22 pm–25 pm under a total dose of 10.5 kGy. Our research demonstrates that the effect of irradiation on the strain sensitivity coefficient of FBG is small and that strain sensing FBGs can work well in the radiation environment.     

非均匀地表空气动力学有效粗糙度的统计特征

利用基于大气边界层Monin-Obukhov相似理论、通量守恒和质量守恒原理设计的非均匀地表空气动力学有效粗糙度计算方案, 研究了3种不同地表类型情况下有效粗糙度的统计特征, 并分析了大气层结稳定度和粗糙变率对有效粗糙度的影响. 结果表明, 有效粗糙度总是大于面积加权平均粗糙度, 大部分情况下有效拖曳系数比平均拖曳系数大10%以上; 有效粗糙度虽然和大气层结稳定度有关, 但对粗糙变率更敏感, 粗糙变率加倍将使有效粗糙度相对变化百分比达到加倍前的4倍, 有效拖曳系数相对变化百分比达到加倍前的3倍. 因此, 非均匀下垫面的数值模式中, 不能简单地采用面积加权平均粗糙度, 需要采用能表示下垫面非均匀性综合效应的有效粗糙度. 关键词： 非均匀性 有效粗糙度 粗糙变率 层结稳定度     

Standardless analysis of solids by mass spectrometry with inductively coupled plasma

The possibility of the standardless mass spectrometric analysis of the elemental composition of solids has been discussed. The effect of each stage of the laser plasma expansion on the formation of the coefficient of relative sensitivity of elements in the sample has been studied theoretically and experimentally. It has been shown that the stages of ionization and detection make the main contribution to the formation of the coefficient of relative sensitivity. It has been proposed to separate dissociation and ionization processes in time and/or in space. To compensate for the energy spread of ions at the output of the analyzer, a circuit has been proposed for aligning the energy of ions before their detection.     

Influence of composition and molecular weight characteristics of methacrylic copolymers on their sensitivity to extreme ultraviolet radiation

Binary and ternary copolymers of (meth)acrylic monomers of different chemical constitution are synthesized. The influence of the composition and molecular weight of copolymers on the sensitivity and contrast of resists based on them under exposure to extreme ultraviolet radiation (λ ～ 13 nm) is investigated. A resist having a radiation sensitivity of 0.6–1.0 mJ cm^?2 and contrast coefficient γ = 1.5 is developed.     

Application of a coherent model in simulating the backscattering coefficient of a mangrove forest

In this paper, a single scattering model is presented for a coherent forest scattering simulation. It is tested on the backscattering coefficient of mangrove forests, which are known to involve large coherent effects. Analysis of branches, leaves and ground contributions is done to understand the backscattering coefficient composition. Finally the sensitivity of the code is investigated.     

Thermoluminescence Kinetic Parameters of TLD-600 and TLD-700 after ~(252)Cf Neutron+Gamma and ~(90)Sr-~(90)Y Beta Radiations

The thermoluminescent(TL) properties such as glow curve structure, relative thermoluminescence sensitivity,dose response linearity of lithium fluoride thermoluminescent dosimeters 6 LiF:Ti,Mg(TLD-600) and 7 LiF:Ti,Mg(TLD-700) are investigated after irradiation ~(252)Cf neutron+gamma and ~(90)Sr-~(90)Y beta sources at room temperature and then the obtained results are compared. The kinetic parameters, namely the order of kinetics b,activation energy Ea and the frequency factor s,are calculated using the computerized glow curve deconvolution(CGCD) program. The effect of heating rate on the glow curves of dosimeters is also investigated. The maximum TL peak intensities and the total area under the glow curves decrease with the increasing heating rate. There is no agreement with the kinetic parameters calculated by the CGCD program for both radiation sources.     

荧光粉相对亮度测量的色修正

由于很难将光接收器的相对光谱灵敏度S(λ)调到与CIE标准观察者V(λ)完全一致,不同荧光份又具有不同的相对光谱功率分布,因此测量荧光粉的相对亮度与测量其它光度量一样,必须进行色修正。本工作针对实际使用的光接收器和相对光谱功率分布不同的几种荧光粉的相对亮度计算了色修正系数。     

Application of a coherent model in simulating the backscattering coefficient of a mangrove forest

Abstract

In this paper, a single scattering model is presented for a coherent forest scattering simulation. It is tested on the backscattering coefficient of mangrove forests, which are known to involve large coherent effects. Analysis of branches, leaves and ground contributions is done to understand the backscattering coefficient composition. Finally the sensitivity of the code is investigated.