Simple tunable multiwavelength Brillouin/Erbium fiber laser utilizing short-length photonic crystal fiber

We have demonstrated a simple ring cavity tunable multiwavelength Brillouin/Erbium fiber laser (MWBEFL), in which 70 m highly nonlinear photonic crystal fiber (HNL-PCF) is used as the Brillouin gain medium. The fiber laser utilizes recycling mechanism to enhance stimulated Brillouin scattering (SBS). The configuration that consists of only 3 optical components is easy to be integrated and improves the practicality. At the maximum 1480 nm pump power of 110 mW and the Brillouin pump power of 3 dBm, 10 stable output channels with more than 10 dB optical signal to noise ratio (OSNR) and 0.078 nm channel spacing could achieve 10 nm tuning ranges.     

Optimization of erbium-doped fiber MOPA laser

An erbium-doped fiber laser (EDFL) constructed in a master oscillator and power amplifier (MOPA) configuration is analyzed. The pump powers for the fiber cavity laser and the booster amplifier stages are managed properly to achieve maximal pump conversion efficiency. Our design achieves a pump conversion efficiency of 91.4%, corresponding to a quantum efficiency of 96.6%, for a 1565.8 nm MOPA laser pumped by a total power of 300 mW at 1480 nm. The optimized MOPA laser shows a 25% enhancement in the pump conversion efficiency, compared to a non-MOPA fiber laser. A side lobe suppression ratio of 48 dB for the optimized MOPA laser is observed.     

Dual-wavelength high-power Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating

We report a high-power dual-wavelength Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating (FMFBG). The FMFBG was fabricated by using a piece of fiber in a length of fiber with a cutoff wavelength of 1225 nm, which supported two modes at 1060 nm. The laser was pumped by a fiber pigtailed laser diode working at 915 nm. Single-wavelength, dual-wavelength and triple-wavelength laser oscillations were observed when the fiber laser operated under different low pump powers. However, stable dual-wavelength operation was achieved at higher pump power of 3.9 W and remained unchanged until the output power reached 5.67 W under the maximum available pump power of 10.7 W. The laser wavelengths were centered at 1059.12 and 1060.80 nm with a full-width at half-maximum of 37 and 43 pm, respectively. The signal-to-noise-ratio was greater than 50 dB and the beam quality factor (M²) was about 1.9.     

High efficiency Tm fiber laser of seed amplification

We use all-fiber single-mode lasers as seed source, amplifiers and pump laser coupling amplifier has been experimentally investigated, respectively. The maximum output power is 10.4 W, with the slope efficiency of 54.4% when the seed laser power is 1 W, and the slope efficiency is 48.7% when the seed laser power is 2 W. The slope efficiency of this scheme is higher than that of the all-fiber amplifier. This can be explained by the loss of pump power at the splice dots. The wavelength of the fiber amplifier is 1947.6 nm, the same as the seed laser's, with a linewidth of 2 nm. We estimate the beam quality to be M² = 2.39, clearly indicating nearly diffraction-limited beam propagation.     

Passively Q-switched Er-doped fiber laser using a semiconductor saturable absorber mirror

A passively Q-switched Er-doped fiber laser using a semiconductor saturable absorber mirror (SESAM) is demonstrated. Q-switching is observed with the output power produced at a slope efficiency of 29.4% with respect to the absorbed pump power. The maximum average output power of 8.37 mW is achieved. The pulse repetition frequency obtained can be turned from 1.72 to 7.95 kHz. The pulse energy of 17.2 nJ has been obtained at the pump power of 46.75 mW, and the pulse width is 30 μs.     

0.16 nm spaced multi-wavelength Brillouin fiber laser in a figure-of-eight configuration

A stable and compact multi-wavelength Brillouin fiber laser (BFL) operating at room temperature is experimentally demonstrated using a 100 m long photonic crystal fiber (PCF) in conjunction with a figure-of-eight configuration. At a Brillouin pump (BP) level of 15.3 dBm, 7 simultaneous lines with 20 GHz or 0.16 nm line spacing is achieved by removing the odd-order Stokes lines. The anti-Stokes lines are also generated via four wave mixing process in the laser cavity. Compared with the Erbium-based multi-wavelength laser, this BFL has advantages in term of channel spacing and flexibility in the choice of operating wavelength. The output spectrum of the proposed BFL can be tuned by 80 nm, dependent on the availability of an appropriate BP source. The multi-wavelength BFL shows a good stability with power fluctuations of less than 0.5 dB over more than 3 h.     

A novel double-Brillouin-frequency spaced multi-wavelength Brillouin erbium-doped fiber laser based on non-linear amplified fiber loop mirror

In the paper, a ring double-Brillouin-frequency spaced multi-wavelength Brillouin erbium-doped fiber laser based on non-linear amplified fiber loop mirror filter is demonstrated, in which the non-linear amplified fiber loop mirror (AFLMF) is used as a filter. At the 980 nm pump power of 10.29 dBm, the tunable laser source center wavelength of 1563 nm and power of −3 dBm, up to 12 even output channels with 0.16 nm spacing are achieved. At the same time, we study the influence of 980 nm pump power, the polarization controller and the tunable laser source center wavelength on the number of Stokes light wave.     

Theoretical analysis and heat dissipation of mid-infrared chalcogenide fiber Raman laser

Based on the structure of mid-infrared chalcogenide fiber Raman laser, the nonlinear coupled equations and heat dissipation equations are constructed. The effects of laser parameters including pump power, fiber length, reflectance of output coupler and fiber loss coefficient on laser performance are numerically analyzed. The results show that the Raman laser pumped at 2 μm can operate at high slope efficiency using the optimized structure parameters. In addition, the output laser power decreases dramatically with the increasing of fiber loss coefficient. Moreover, the temperature distributions along the fiber radial and axial directions and the maximum temperature versus launched pump power are calculated according to the heat dissipation equations. The results show that the maximum temperature in the fiber increases dramatically with the increasing launched pump power, which is above 300 °C for launched pump power of 21 W. The above obtained results can be used for theoretical guiding and optimizing design of practical chalcogenide fiber Raman laser.     

Thermally tunable microfiber knot resonator based erbium-doped fiber laser

A compact and tunable erbium-doped fiber laser is demonstrated using a highly doped fiber and a microfiber knot resonator (MKR) structure which is laid on the surface of a small peltier. The MKR functions as both a reflector and a tunable filter where tunability is achieved by varying the temperature of the resonator by heating the peltier. A stable laser output is achieved at the 1533 nm region with an optical signal to noise ratio (OSNR) of 27 dB using a 65 mW of 980 nm pump power. The operating wavelength of the laser can be tuned from 1532.60 nm to 1533.49 nm as the temperature is increased from the room temperature of 24 to 90 °C. It is observed that the operating wavelength shifts to a longer wavelength as the temperature increases with an efficiency of 12.4 pm/°C. This is due to the thermally induced optical phase shift attributable to the changes in effective refractive index and optical path length of the MKR loop.     

800 mW/1484 nm highly efficient two-cascaded phosphosilicate Raman fiber laser pumped by Nd:YVO4 solid-state laser

Using 1064 nm CW Nd:YVO₄ solid-state laser as a pump, 1-km phosphosilicate fiber and cascaded cavities with two pairs of fiber Bragg grating mirrors for 1239 and 1484 nm, we obtained a CW 800 mW/1484 nm Raman fiber laser (RFL) for an actual incident pump power of about 2 W (Nd:YVO₄ power of 6.90 W). The conversion efficiency is as high as 40%. To the best of our knowledge, this is the highest conversion efficiency of RFL pumped by solid-state laser. The output power instability at 1484 nm in half an hour is less than 3%. In addition, the numerical simulations are also performed. Good agreement between the results of numerical simulation and the results of the experiment has been demonstrated.     

Side-pumped fiber laser

A neodymium-doped side-pumped double-clad fiber laser operating at 1.06 µm is described. We report here, what is, to our knowledge, the first exclusively repetitive side-pumping scheme with two monomode laser diodes. Side-pumping has been realized by prism-fiber couplers. A pump-light-loss analysis at the pump positions has been performed. An output power of 13.5 mW is obtained with both diode lasers. The highest slope efficiency of 66% with respect to absorbed pump power at 809 nm is achieved when pumping with only one diode.     

High power single transverse mode operation of a tapered large-mode-area fiber laser

To get high output power with good beam quality, a tapered section is introduced to large-mode-area (LMA) Yb-doped fiber laser. Output characteristics of the fiber laser without tapered section and with tapered section are compared experimentally. When the launched pump power is 119.1 W, 77.9 W with M² 3.08 and 56.4 W with M² 1.14 can be obtained, respectively. The corresponding slope efficiencies are 71.8% and 54.1%, respectively. Although output power of the tapered fiber laser has 30.6% penalty, brightness of it is as much as 5.28 times of the fiber laser without tapered section. Moreover, spectra of them are measured. It is found that tapered section makes lasing wavelength of the fiber laser shorter.     

Self-Q-switching and mode-locking in an all-fiber Er/Yb co-doped fiber ring laser

Using a section of un-pumped Er/Yb co-doped fiber (EYDF) as a saturable absorber, Self-Q-switching and self-mode-locking pulses have been obtained in an all-fiber EYDF ring laser. Such laser is with the self-Q-switched pulse threshold of 135.22 mW, the repetition rate of approximately 22.2 kHz, and the pulse duration of ∼2.8 μs, respectively. The self-mode-locked threshold is 591.8 mW. By incorporating the saturable absorption in an un-pumped EYDF and a Mach-Zehnder interferometer, when the pump power is increased to 1242.9 mW, the continuous-wave (CW) mode-locking with the pulse width of 26 ns has also been demonstrated experimentally for the first time.     

The optimum length of linear cavity Yb-doped double-clad fiber laser

In order to improve the performance of the double-clad fiber laser, the optimum laser length needs to be estimated prior to the experiment. Previous expressions for the optimum length of fiber laser have been established under some assumptions, such as the output power without laser scattering loss and the pump power without reflection in the output-end. In this work, the issue of optimum laser length has been analyzed theoretically based on the strongly pumped fiber laser model. An extended expression for the optimum length of the linear cavity Yb³⁺-doped double-clad fiber laser is obtained. The respective effects of the laser scattering loss, the pump power, the Yb³⁺ dopant concentration, and the pump reflection on the optimum laser length are identified.     

Q-switched fiber laser by all-fiber piezoelectric modulation and pulsed pump

We have demonstrated a Q-switched fiber laser based on a mechanical all-fiber Q-switching module and pulsed-pump configuration. A piezoelectric actuator was utilized in the module to change the round-trip loss of the fiber laser cavity, and exploited the pulsed pump to prevent the multiple pulsing phenomena. Q-switching pulses were successfully achieved at the repetition rates from 1 Hz to 2 kHz, and the average output power was 11 mW. The peak power in excess of 114 W with associated pulse width of 193 ns was obtained at the repetition rate of 500 Hz. Besides preventing multiple pulsing phenomena, pulsed-pump configuration can also suppress amplified spontaneous emission and increase pulse stability and peak power simultaneously.     

Directivity influence of signals propagation through EDFA gain medium of Brillouin-erbium fiber laser

We experimentally demonstrate a multiwavelength Brillouin-erbium fiber laser in two configurations; uni-directional and bi-directional propagation of Brillouin pump and Brillouin Stokes signals through an Erbium-doped fiber gain. The influence of these configurations on the performance of the output parameters in terms of lasing threshold, output channel generation and tuning range of the generated output channels are investigated. We discovered that there is a trade-off between these two fiber laser configurations. The uni-directional amplifier configuration provides greater tuning range of 46.8 nm against 23 nm at maximum Brillouin pump power of 2 mW and 1480-nm pump power of 130 mW. On the other hand, the bi-directional amplifier configuration provides 13 output channels against 6 output channels obtained from the uni-directional amplifier configuration at the same pumping powers. Nevertheless, the bi-directional amplifier configuration requires much lower pump power to initiate lasing.     

Continuous-wave Ho:GdVO4 laser pumped by Tm-doped fiber laser with a fiber Bragg grating at room temperature

We reported the Ho:GdVO₄ laser pumped by Tm-doped laser with a fiber Bragg grating. 2.03 W continuous-wave Ho:GdVO₄ laser output power is obtained under 10.5 W incident pump power, with the optical-to-optical conversion efficiency and slope efficiency of 19.3% and 32.3%, respectively, at 7 °C. We can see that, the lower the temperature is, the better the laser output character is. The beam quality factor is M² ∼ 1.29 measured by the traveling knife-edge method.     

Novel shooting method with simple control strategy for fiber lasers

A novel shooting method with excellent simple control strategy is developed for solving the failure to convergence of the traditional shooting methods themselves in fiber lasers model. Compared with the published literature, the novel shooting method provides a clear physical understanding method for getting the threshold pump power and the exact results with given random functions in Yb³⁺-doped fiber lasers and Er³⁺-doped fiber lasers. Then, the results in Er³⁺-doped fiber lasers and Yb³⁺-doped fiber lasers demonstrate that the solutions using the novel shooting method has high accuracy of 10⁻⁸ W with several iteration steps, which have extended the applicable range of the end-pumped power even lower than 1 mW pump power. Furthermore, compared with 1480 nm pump for the threshold and slope efficiencies of the Er³⁺-doped fiber lasers, 978 nm fiber lasers can extend wider scope of application and be pump source in the coming future. Finally, the lower threshold and higher slope efficiency at 975 nm than those of 910 nm pump in Yb³⁺-doped fiber lasers, 975 nm pump laser provides for broad band excellent cladding pump source.     

169 MHz repetition frequency all-fiber passively mode-locked erbium doped fiber laser

Passively mode-locked stretched-pulse erbium fiber laser is presented. With all-fiber configuration 111 fs pulses were achieved with the fundamental repetition rate of 169 MHz and an average output power of more than 30 mW. Proposed setup shows excellent stability, reliability and ‘turn-key’ operation. The impact of the pump power on laser parameters is described.     

A tunable narrow-line-width multi-wavelength Er-doped fiber laser based on a high birefringence fiber ring mirror and an auto-tracking filter

A novel multi-wavelength erbium-doped fiber laser operating in C-band is proposed and successfully demonstrated. The wavelength interval between the wavelengths is about 0.22 nm. The 3 dB bandwidth of the laser is about 0.012 nm, and the output power reaches 4.8 mW. By using a high birefringence fiber ring mirror (HiBi-FLM) and a tunable FBG, the laser realizes switchable and tunable characteristic. The mode hopping can be effectively prevented. Moreover, this laser can improve wavelength stability significantly by taking advantage of an un-pumped Er³⁺-doped fiber at the standing-wave section. The laser can operate in stable narrow-line-width with single-, dual-wavelength, and unstable triple-wavelength output at room temperature.