Effects of forming gas annealing on LiNbO3 single crystals

Z-cut congruent LiNbO₃ single crystals were annealed in 95%N₂+5%H₂ at high temperatures. X-ray diffraction showed that 2θ of (0 0 0 6) peak is obviously reduced by 0.6° and 1.0° for the samples annealed at 600 and 900 °C, respectively. A new peak appears at the high-energy side of O 1s spectrum in X-ray photoelelectron spectroscopy (XPS) analyses, and the leakage current is greatly increased. It is proposed that hydrogen is incorporated in LiNbO₃ single crystals through forming gas annealing at temperatures up to 900 °C and exists in LiNbO₃ as a proton bound to an oxygen ion through O-H bond with its electron donated.     

Lateral-field-excitation properties of LiNbO3 single crystal

LiNbO 3 has been found attractive for lateral field excitation (LFE) applications due to its high piezoelectric coupling. In this paper, bulk acoustic wave propagation properties for LiNbO 3 single crystal excited by a lateral electric field have been investigated using the extended Christoffel-Bechmann method. It is found that the LFE piezoelectric coupling factor for c mode reaches its maximum value of 95.46% when ψ = 0 for both (yxl)-58 and (yxwl)±60 /58 LiNbO 3 . The acoustic wave phase velocity of c mode TSM (thickness shear mode) changes from 3456 m/s to 3983 m/s as a function of ψ. Here ψ represents the angle between the lateral electric field and the crystallographic X-axis in the substrate major surface. A 5 MHz LFE device of (yxl)-58 LiNbO 3 with ψ = 0 was designed and tested in air. A major resonance peak was observed with the motional resistance as low as 17 and the Q-factor value up to 10353. The test result is well in agreement with the theoretical analysis, and suggests that the LFE LiNbO 3 device can be a good platform for high performance resonator or sensor applications.     

Morphology of ablation craters generated by fs laser pulses in LiNbO3

The surface morphology of the ablation craters generated in LiNbO₃ by 130 fs laser pulses at 800 nm has been investigated by AFM/SNOM microscopy. The single pulse fluence corresponding to the ablation threshold has been estimated to be ≈1.8 J/cm².A complex structure including random cone-shaped protrusions is observed inside the ablated crater. The scale of the protrusion spacing is in the submicron range and the heights are typically of a few tens of nanometers. At and outside the crater rim a novel quasi-periodic wave-like topography pattern is observed in both types of microscopy techniques. The average wavelength, that is slightly dependent on pulse fluence, is (500-800 nm) comparable to the light wavelength. This novel topography feature keeps a close similarity with a Fresnel diffraction pattern by an absorbing circular obstacle or impact wave pattern produced by a combination of heat and shock wave (resemble that of impact crater). It is proposed that the obstacle is associated to the strongly nonlinear multiphoton absorption at the peak of the pulse profile. The energy deposited by nonlinear absorption of such profile causes ablation of both the crater and the rippled structure.     

Theoretical explanation of g factors for Ti ions in LiNbO3 and LiTaO3 crystals

The EPR g factors g_// and g_⊥ for Ti³⁺ ions at the trigonal octahedral Li⁺ sites of LiNbO₃ and LiTaO₃ crystals are calculated from the third-order perturbation formulas of g factors for 3d¹ ion in trigonal symmetry. In the calculations, the crystal-field parameters are obtained from the structural data by using the superposition model. The calculated values are in reasonable agreement with the observed values. The results are discussed.     

Properties study of LiNbO3 lateral field excited device working on thickness extension mode

This paper investigates the properties of thickness extension mode excited by lateral electric field on LiNbO3 by using the extended Christoffel-Bechmann method. It finds that the lateral field excitation coupling factor for amode (quasi-extensional mode) reaches its maximum value of 28% on X-cut LiNbO3. The characteristics of a lateral field excitation device made of X-cut LiNbO3 have been investigated and the lateral field excitation device is used for the design of a high frequency ultrasonic transducer. The time and frequency domain pulse/echo response of the LiNbO3 lateral field excitation ultrasonic transducer is analysed with the modified Krimholtz-Leedom-Matthae model and tested using traditional pulse/echo method. A LiNbO3 lateral field excitation ultrasonic transducer with the centre frequency of 33.44 MHz and the -6 dB bandwidth of 33.8% is acquired, which is in good agreement with the results of the Krimholtz-Leedom-Matthae model. Further analysis suggests that the LiNbO3 lateral field excitation device has great potential in the design of broadband high frequency ultrasonic transducers.     

Ultraviolet laser-induced photovoltaic effects in miscut ferroelectric LiNbO3 single crystals

This paper investigates the photovoltaic properties of miscut LiNbO 3 single crystal with different thicknesses under irradiation of a 248 nm ultraviolet laser pulse with 20 ns duration without an applied bias.Nanosecond photovoltaic response is observed and faster rise time is obtained in thinner samples.In accord with the 248 nm laser duration,the full width at half maximum of the photovoltaic signals keeps a constant of ～ 20 ns.With decrease of the crystal thickness,the photovoltaic sensitivity was improved rapidly at first and then decreased,and the maximum photovoltage occurred at 0.38 mm-thick single crystal.The present results demonstrate that decreasing the LiNbO3 single crystal thickness can obtain faster response time and improve the photovoltaic sensitivity.     

Widely phase-matched tunable difference-frequency generation in periodically poled LiNbO3 crystal

We report on the development of a laser source in the mid-infrared spectral region based on difference-frequency generation (DFG) in a periodically poled LiNbO₃ (PPLN) crystal. Continuously tunable coherent radiation from 2.75 to 4.78 μm was produced by optical parametric interaction between a diode-pumped monolithic continuous-wave (CW) Nd:YAG laser operating at 1.064 μm and a CW Ti:Sapphire laser tunable from 767 to 871 nm. Temperature-dependent quasi-phase-matched DFG wavelength acceptance bandwidth was studied and characterized. An empiric formula is given to estimate the phase-matched wavelength acceptance bandwidth as a function of the crystal temperature at Λ = 22.5 μm. A large frequency scan of 128 cm⁻¹ (about 78 cm⁻¹ above 1 μW) near 4.2 μm was achieved. The whole absorption spectrum of the P and R branches of the ν₃ band of atmospheric carbon dioxide has been recorded with a single phase-matched frequency scan.     

掺镁铌酸锂亚微米结构畴反转的研究

研究了掺镁铌酸锂(MgO：LiNbO₃)的极化特性及其畴壁运动的性质,通过调节多个脉冲外加电场来控制畴壁的运动,在背向反转效应作用下,反转畴发生劈裂,制备出均匀的掺镁铌酸锂亚微米周期畴结构,并分析探讨了掺镁铌酸锂亚微米结构的成因及其反转机理. 关键词： 亚微米畴结构 掺镁铌酸锂 背向反转     

White light interferometry test and analysis of LiNbO3 polarizer

White light interferometer can be used to measure the amplitude extinction ratio (ER) of polarizer and coupling distribution in fiber. A LiNbO₃ polarizer coupled with a polarization maintaining fiber and a silica planar waveguide at the two ends was measured using white light interferometer. According to the principles of optical coherence domain polarimeter (OCDP) technique, the test scheme is analyzed and presented to measure the ER of LiNbO₃ polarizer with its apparatus proposed correspondingly. By analyzing the interference intensity, both the ER of LiNbO₃ polarizer and its coupling crosstalk with optical fiber and waveguide are obtained. The results illustrate that the ER of a 5 mm-long LiNbO₃ polarizer is 71 dB and the crosstalk of the coupling points are around 40 dB. The results have good agreement with analysis.     

Theoretical expression for change of extraordinary refractive index in annealed proton exchanged LiNbO3 optical waveguides

A general expression for the change in extraordinary refractive index of the annealed proton exchanged LiNbO₃ waveguide has been deduced. The expression deduced explains the experimental results of decrease in change of extraordinary refractive index with annealing. The effect of annealing time has also been incorporated following Cao's model (Cao, Ramaswamy, Srivastava, J. Lightwave Technol. 10 (1992) 1302–1313). The concentration profile of protons in the annealed waveguide has been deduced theoretically, which is consistent with the previous results. The spontaneous polarization has been considered as the central mechanism for change in extraordinary refractive index due to proton exchange with annealing.     

飞秒激光制作铌酸锂光波导的研究

针对Z切割铌酸锂晶体在中心波长为800 nm、重复频率为76 MHz的飞秒脉冲激光下,利用放大倍数为40、数值孔径为0.65的会聚透镜聚焦,研究了扫描速度和扫描次数的变化对刻写光波导结构的影响,分析了波导结构变化的原因,并测试了1×2光波导功分器的通光性能.实验结果表明:在采用横向扫描、聚焦深度为350~400 μm、扫描速度为100 μm/s和激光功率为250 mW时,获得较理想的铌酸锂光波导,1×2光波导功分器的输出功率分布基本达到均分.     

Measurement of Wavelength Dependence of Electro-Optic Coefficients r22 of Non-doped and 5% MgO-doped Congruent LiNbO3 Crystals and 1.8% MgO-doped Quasi-stoichiometric LiNbO3 Crystal by Multiple Reflection Interference Method

The electro-optic coefficient r ₂₂ in the wavelength range from 409 to 1580 nm was measured for non-doped and 5% MgO-doped congruent LiNbO₃ crystals and 1.8% MgO-doped quasi-stoichiometric LiNbO₃ crystals in a simple optical system using a multiple reflection interference method capable of producing high-precision results without the application of antireflection film to the end faces of the crystal. The influence of the manufacturing errors of the electrooptic crystals was discussed on the measurement of the r ₂₂ coefficient. The experimental errors are less than approximately 0.5% in the wavelength range from 409 to 1064 nm and approximately 1% from 1340 to 1580 nm. It was further shown that polarizing of the laser along X axis resulted in highly accurate measurement of the r ₂₂ of LiNbO₃ crystals.     

Deposition of ZnO multilayer on LiNbO3 single crystals by DC-magnetron sputtering

Zinc oxide (ZnO) thin films were deposited on LiNbO₃ (LN) single crystals with 200 nm thicknesses by three different ways, where coating of zinc (Zn) film was followed by thermal oxidation for four, two, and one steps with 50, 100, and 200 nm thicknesses repeatedly. Sample, which was produced at 4-step of deposition and oxidation of Zn layer, showed high transmittance and low structural defect due to a lower photoluminescence intensity and Urbach energy. Average grain size in X-ray diffraction (XRD), scanning electron microscopy (SEM) micrograph, and atomic force microscopy (AFM) images for multilayer of ZnO was lower than monolayer of ZnO thin films. Applying multilayer coating technique leads to decrease of surface roughness and scattering on light on surface and fabrication of LiNbO₃ waveguides with lower optical loss.     

Investigation of nonvolatile holographic storage in LiNbO3:Mn:Ce:Fe crystal

We investigate the persistent holographic recording in triply doped LiNbO₃:Mn:Ce:Fe crystals at different oxidation/reduction states. The experimental results show that there is an optimum oxidation/reduction state, which results in the best dynamic range M/#. Compared with doubly doped LiNbO₃:Ce:Fe, we found that the nonvolatile diffraction efficiency and the best dynamic range M/# obtained in triply doped samples are larger than that obtained in doubly doped samples. The reason for the increase of the crystal about the nonvolatile diffraction efficiency and the dynamic range M/# was also explained.     

周期极化掺镁不同组分LiNbO3晶体的研究

利用气相平衡扩散法研制出掺镁不同组分的LiNbO₃晶体，并对其极化特性进行了研究.研究表明晶体的开关电场和自发极化不仅与晶体组分［Li］/［Nb］比有关而且与掺镁量有关，［Li］/［Nb］比为0.973掺入2mol% MgO的近化学比LiNbO₃晶体的开关电场仅为1.8kV/mm，是同成分晶体的1/12，且其极化结构的质量要远好于同成分LiNbO₃晶体和近化学比LiNbO₃晶体. 关键词： 气相平衡扩散 3晶体')" href="#">掺镁LiNbO₃晶体 周期极化     

Spectroscopic analysis of Er transition in Mg/Er-codoped LiNbO3 crystal

We present a Judd-Ofelt spectroscopic analysis on the Mg/Er-codoped congruent lithium niobate (LiNbO₃) crystals. The Judd-Ofelt model is applied to the room temperature unpolarized absorption intensities of Er³⁺ ions on eleven transition bands to determine their intensity parameters: Ω₂=2.36×10⁻²⁰ cm², Ω₄=0.76×10⁻²⁰ cm², Ω₆=0.30×10⁻²⁰ cm² in Er:LiNbO₃ crystal heavily codoped with MgO. The radiative lifetime of ²H_9/2 becomes longer when MgO is added into Er:LiNbO₃ crystal. The experimental lifetimes are obtained using microsecond time-resolved spectra at 400 nm femtosecond pulse excitation to predict radiative quantum efficiency. Combining higher radiative quantum efficiency with longer radiative lifetime, we conclude that Mg/Er-codoped LiNbO₃ crystals are more suitable than Er: LiNbO₃ ones in laser materials.     

外加电场法制备LiNbO3周期畴的反转电流特性研究

采用外加电场法制备了LiNbO₃单晶周期畴结构. 在对不同尺寸周期畴的反转电流进行比较研究的基础上,提出了一种确定反转畴成核时间和纵向贯穿速率的方法. 根据这一方法,得到在电场强度为25.1kV/mm,脉冲宽度为50 ms的脉冲方波作用下,LiNbO₃单晶反转畴的成核时间约为80ns,纵向贯穿速率约为0.1667m/s. 关键词： 3单晶周期极化')" href="#">LiNbO₃单晶周期极化 反转电流 反转畴成核时间 反转畴纵向贯穿速率     

飞秒激光刻写1×4铌酸锂光波导功分器的研究

采用一种以五次幂函数为基础所设计的1×4光波导功分器路径,利用中心波长为800 nm、重复频率为75 MHz的飞秒脉冲激光为光源,通过控制三位电动平移台,在Z切割铌酸锂晶体进行横向扫描此路径,在激光功率为270 mW和扫描速度为0.05 mm/s下,制备出1×4光波导功分器,分析了改变扫描速度和扫描次数对波导形成的影响,以及波导形成的原因.实验结果表明:在强激光的各种参量一定时,扫描速度越小,扫描次数越多,波导线宽越大,扫描速度在一定范围内时,波导损耗较低.     

准相位匹配PPLN倍频理论研究与优化设计

对准相位匹配周期性极化铌酸锂(PPLN)倍频进行了理论研究，并对聚焦高斯光束条件下的倍频耦合波方程进行了求解，给出了准相位匹配倍频转换效率公式，分析了晶体长度与聚焦程度的关系，在此基础上对倍频谐振腔进行了优化设计，以期获得最大的倍频转换效率.本结果对准相位匹配倍频器件的设计具有一定的指导意义. 关键词： 倍频 准相位匹配 周期性极化铌酸锂