Determination of inorganic cations and ammonium in environmental waters by ion chromatography with a high-capacity cation-exchange column

While alkali and alkaline earth cations are commonly determined by using spectrometric techniques such as atomic absorption spectrometry or inductively coupled plasma, ammonium cation in the same sample must be measured separately by a wet chemical technique such as colorimetry, titrimetry, or ammonia-selective electrode. In a single 25-min run ion chromatography can determine all of the important inorganic cations including lithium, sodium, ammonium, potassium, magnesium and calcium. In this paper, we describe the use of ion chromatography with a new high-capacity cation-exchange column (the IonPac CS16), an electrolytically-generated methanesulfonic acid eluent and suppressed conductivity detection to determine dissolved alkali and alkaline earth cations and ammonium in drinking water wastewater and aqueous soil extracts. The IonPac CS16 is a high-capacity cation-exchange column that incorporates recent advances in polymer chemistry to enable trace-level determinations of cations even in high-ionic-strength matrices. We discuss the linear range, method detection limits, and analyte recoveries obtained with this column, and evaluate the effect of potential interferences on method performance during the analysis of typical environmental samples.     

Determination of trace concentrations of bromate in municipal and bottled drinking waters using a hydroxide-selective column with ion chromatography

The International Agency for Research on Cancer determined that bromate is a potential human carcinogen, even at low micro/l levels in drinking water. Bromate is commonly produced from the ozonation of source water containing naturally occurring bromide. Traditionally, trace concentrations of bromate and other oxyhalides in environmental waters have been determined by anion exchange chromatography with an IonPac AS9-HC column using a carbonate eluent and suppressed conductivity detection, as described in EPA Method 300.1 B. However, a hydroxide eluent has lower suppressed background conductivity and lower noise compared to a carbonate eluent and this can reduce the detection limit and practical quantitation limit for bromate. In this paper, we examine the effect of using an electrolytically generated hydroxide eluent combined with a novel hydroxide-selective anion exchange column for the determination of disinfection byproduct anions and bromide in municipal and bottled drinking water samples. EPA Methods 300.1 B and 317.0 were used as test criteria to evaluate the new anion exchange column. The combination of a hydroxide eluent with a high capacity hydroxide-selective column allowed sub-microg/l detection limits for chlorite, bromate, chlorate, and bromide with a practical quantitation limit of 1 microg/l bromate using suppressed conductivity detection and 0.5 microg/l using postcolumn addition of o-dianisidine followed by visible detection. The linearity, method detection limits, robustness, and accuracy of the methods for spiked municipal and bottled water samples will be discussed.     

毛细管电泳定量检测环境水样中无机阴离子

详细讨论了胶束浓度、间接吸收背景物质的浓度及有机添加剂组成等对部分卤素及其含氧酸根的毛细管电泳分离影响;在优化的条件下,3.5min内高效、快速地完成了Cl-、Br-、ClO3-、BrO3-四种无机阴离子的分离分析,分离的理论塔板数在1.6×106～2.8×105/m之间,检出限在11.2～23.3mg/L之间,迁移时间的相对标准偏差小于1%,峰面积的相对标准偏差在5.2%～2.2%之间;并将方法用于环境水样的分析。     

Determination of inorganic and organic anions in one run by ion chromatography with column switching

A method for the simultaneous determination of low-molecular-mass organic and inorganic anions in aqueous solutions was developed using isocratic ion chromatography (IC) with suppressed conductimetric detection and column switching. Owing to the large differences in distribution coefficients between sulphate, nitrate and phosphate and the other species, these ions are separated in the first stage on a medium-capacity anion exchanger, whereas the other anions are led through a second column packed with a high-capacity anion-exchange resin via a column-switching valve. After optimization of the switching procedure a spiked drinking water sample was analysed. Fluoride, acetate, butyrate, formate, nitrate, nitrite and phosphate could be determined in addition to the main anions (chloride and sulphate). The time for a complete analysis is less than 20 min and the method can easily be automated. The precision and detection limit are as usual in IC with background suppression.     

Determination of common inorganic anions and cations by non-suppressed ion chromatography with column switching

An ion chromatography (IC) method has been proposed for the determination of seven common inorganic anions (F(-), H(2)PO(4)(-), NO(2)(-), Cl(-), Br(-), NO(3)(-), and SO(4)(2-)) and/or five common inorganic cations (Na(+), NH(4)(+), K(+), Mg(2+), and Ca(2+)) using a single pump, a single eluent and a single detector. The present system used cation-exchange and anion-exchange columns connected in series via a single 10-port switching valve. The 10-port valve was switched for the separation of either cations or anions in a single chromatographic run. When 1.0mM trimellitic acid (pH 2.94) was used as the eluent, the seven anions and the five cations could be separated on the anion-exchange column and the cation-exchange column, respectively. The elution order was found to be F(-)相似文献   

Determination of inorganic anions by ion chromatography using a graphitized carbon column dynamically coated with cetyltrimethylammonium ions.

The simultaneous determination of inorganic anions by ion chromatography using a dynamically coated graphitized carbon column with cetyltrimethylammonium (CTA) ions was investigated with suppressed conductivity detection. Column preparations with CTA and sodium carbonate-sodium hydrogencarbonate concentration in the eluent were examined to optimize the separation of seven common anions (F-, Cl-, NO2-, Br-, NO3-, HPO(4)2- and SO(4)2-). Calibration curves were linear from 0.5 to 5 micrograms/ml for F-, from 1.0 to 10 micrograms/ml for Cl-, from 1.5 to 15 micrograms/ml for NO2-, from 2.0 to 20 micrograms/ml for Br- and NO3-, from 5.0 to 50 micrograms/ml for HPO(4)2- and from 3.0 to 30 micrograms/ml for SO(4)2- with correlation coefficients (r) of 0.999 or better. The relative standard deviations of peak areas were between 0.3 and 0.9% for 10 repeated measurements. The application of this newly developed method was demonstrated by the determination of inorganic anions in the water for pharmaceutical purposes. Using CTA-Br as the coating agent, a permanently coated ion-exchange column was obtained, which allowed efficient separations of seven anions without adding any coating agent to the eluent.     

Determination of inorganic anions by capillary electrochromatography

Recent advances in the separation of inorganic anions by capillary electrochromatography (CEC) are reviewed. Due to the nature of these analytes, the area is dominated by use of ion-exchange (IE) stationary phases in packed, open-tubular or pseudo-phase columns. The strengths and weaknesses of each format in the IE mode are compared and discussed. It is shown that the selectivity of these systems can be modelled accurately using physical retention models and that these models can subsequently be used for method optimisation. Further developments in the field which can be expected in the near future are also discussed.     

Determination of inorganic anions in saliva by capillary isotachophoresis

Nitrite, nitrate, iodide and thiocyanate have been quantified in non-smoker and smoker saliva by capillary isotachophoresis (CITP). Hydrochloric acid (10 mmol l⁻¹) adjusted with histidine to pH 6.0 plus 6% poly(vinylpyrrolidone) was used as the leading electrolyte (LE) and 5 mmol l⁻¹ acetic acid as the terminating electrolyte (TE). Linearity was observed from 0.005 to 0.500 mmol l⁻¹ with a coefficient of determination (r²) of 0.999. The separation of anions was achieved in less than 19 min. The minimal sample pretreatment and relatively low running cost make isotachophoresis good alternative to existing methods.     

Determination of inorganic anions in mushrooms by ion chromatography with potentiometric detection

A simple method for determination of common inorganic anions in mushroom samples has been developed by using suppressed ion chromatography with a pH detection unit. The detection unit which was constructed in such a way that practically no additional dispersion occurred consisted of a flow-through quinhydrone pH sensor and a small reference electrode. Chromatographic separation was performed in the order F⁻, Cl⁻, NO₂⁻, Br⁻, PO₄³⁻, ClO₃⁻, NO₃⁻, and SO₄²⁻, at room temperature by using Ion Pac AS 9-HC anion exchange column. Anion extracts from dried mushroom samples at room temperature were homogenized and filtered before injection. Under optimized analytical conditions, the detection limits of the method were between 2 × 10⁻⁶ and 3 × 10⁻⁴ M, depending on the anion studied. The results showed that the concentrations of fluoride and bromide in all mushroom samples were below their limit of detection. Nitrite was found to be the lowest abundant ion, while the most abundant ion was sulfate in all the mushroom samples studied.     

Separation of inorganic anions on a high capacity porous polymeric monolithic column and application to direct determination of anions in seawater

A commercially available 4.6 mm id x 50 mm polymethacrylate-based monolithic strong anion exchange column (ProSwift SAX-1S) designed for the separation of proteins has been successfully used to separate small inorganic anions in the presence of a seawater sample matrix. Using a hydroxide eluent with suppressed conductivity detection the ion exchange capacity of this column declined over time; however, using KCl as the eluent, the column performance was stable with a capacity of 530 microequiv. for nitrate. The optimum conditions for the separation of iodate, bromate, nitrite, bromide and nitrate were assessed by constructing van Deemter plots using 1.00 and 0.100 M KCl. Efficiencies of up to 26 700 plates/m were recorded using 1.00 M KCl, at a flow rate of 0.20 mL/min but iodate was not baseline resolved from the void peak. By reducing the concentration of the eluent to 0.100 M, efficiencies of up to 39 900 plates/m could be obtained at 0.35 mL/min. By employing a linear gradient ranging from 0.05 to 1.00 M KCl the ions dissolved in distilled water or a salt water matrix could be baseline separated in less than 3 min at a flow rate of 2.50 mL/min.     

Determination of inorganic anions in Kraft pulping liquors by capillary electrophoresis

Various sulfur containing anions (sulfate, sulfite, and thiosulfate) in Kraft pulping process liquors are determined by capillary electrophoresis. In addition, other inorganic anions (hydroxide, chloride, oxalate, carbonate) are analyzed with the developed method. Through optimization of the separation conditions it is possible to simultaneously determine these anionic species in pulping liquors with direct and indirect UV detection at 185, 214, and 254 nm. To ensure short separation times a migration of the anionic analytes in the same direction as the electroosmotic flow (co-electroosmotic CE) is established by reversal of the electroosmotic flow with 1,5-dimethyl-1,5-diazaundecamethylene polymethobromide (hexadimethrine bromide; HDB; polybrene™) which is added to the electrolyte as EOF modifier. The impact of acetonitrile as organic modifier to improve the selectivity of the anionic analytes is also investigated. The developed method is then applied to analyze and quantify various anions in pulping liquors (white and black liquors). By simultaneously determining the hydroxide concentration it is possible to calculate effective alkalinity and sulfidity with the measured concentrations without the need of volumetric methods.     

Determination of colloidal electrolytes: amperometric titration of dodecylquinolinium bromide with inorganic anions

The possibilities of the amperometric titration of aqueous solutions of dodecylquinolinium bromide in 0.1 mol dm^?3 potassium bromide as supporting electrolyte with potassium dichromate, potassium hexacyanoferrate(III) and ammonium molybdate were investigated. Titrations were carried out in which dichromate, hexacyanoferrate(III) and molybdate anions were determined by titration of colloidal electrolyte solutions.     

二维离子色谱法同时测定4种无机阴离子和葡萄糖酸根离子

建立了一种新的二维离子色谱分析模式,应用阀切换技术并联抑制电导和脉冲安培双检测体系,同时测定Cl^-、NO₂^-、SO₄^2-、NO₃^-和葡萄糖酸根离子。第一维色谱采用Ionpac AG18+Ionpac AS18阴离子分析柱,分别以5和20 mmol/L的NaOH溶液等度淋洗,流速为1.0 mL/min,进样量为25 μL,抑制电导检测Cl^-、NO₂^-、SO₄^2-和NO₃^-。第二维色谱采用CarboPac PA1+CarboPac PA20两保护柱串联,以90 mmol/L NaOH溶液、0.8 mL/min的流速洗脱,由AG15柱分离富集葡萄糖酸根,脉冲安培检测器检测。结果表明:无机阴离子在0.1~5.0 mg/L、葡萄糖酸根在0.0856~4.2825 mg/L范围内有良好的线性关系,RSD在1.05%~1.94%之间,相关系数(R²)在0.9945以上;无机阴离子的方法检出限为0.615~2.17 μg/L,葡萄糖酸根的方法检出限为24.24 μg/L;回收率在90.3%~102.8%之间。该方法并联两种检测模式,有良好的准确度和精密度,适用于复杂样品的分离分析。     

Determination of inorganic cations and anions by ion-exchange chromatography with evaporative light-scattering detection

Evaporative light-scattering detection (ELSD) was investigated for the direct determination of alkali and alkaline-earth cations by cation-exchange chromatography. Successful single run analysis of Na+, K+, Mg2+ and Ca2+ was achieved in 11 min on the Hamilton PRP-X200 column using an aqueous solution of ammonium formate as mobile phase under a salt concentration step gradient mode (20 mM and 100 mM). Surprisingly the use of ELSD reveals a weak retention of inorganic anions (Cl-, NO3-, SO4(2-)) onto the polymeric cation exchanger, which enables the simultaneous determination of inorganic anions (C1- and NO3-) associated with the cations analysed (Na+ and K+).     

Spectrophotometric determination of nitrite in environmental waters using column preconcentration on biphenyl

Column preconcentration methods have been established for the spectrophotometric determination of trace nitrite with sulfanilic acid (SA) orp-aminoacetophenone (AAP) as the diazotizable aromatic amine andN, N-dimethylaniline (DMA) or 1-aminonaphthalene (AN) as the coupling agent, using differention-pairs co-precipitated with biphenyl. Nitrite ion reacts with SA in the pH range 2.0–3.0 and AAP in the pH range 1.7–3.0 in HCl medium to form water-soluble colourless diazonium cations. These cations are subsequently coupled with DMA in the pH range 3.7–6.1 for the SA-DMA system and AN in the pH range 1.7–2.3 for the AAP-AN system to be retained on microcrystalline biphenyl packed in a column. The solid mass is dissolved out from the column with 5 ml of DMF and the absorbance is measured by a spectrophotometer at 420 nm for the SA-DMA system and at 517 nm for the AAP-AN system. The calibration was linear over the concentration ranges 0.3–6.0 g of nitrite in 5 ml of DMF solution (i.e., 0.02–0.40 g/ml in the sample solution) for the SA-DMA system and 0.5–7.0 g of nitrite in 5 ml of DMF solution (i.e., 0.03–0.47 g/ml in the sample solution) for the AAP-AN system. The molar absorptivity and Sandell's sensitivity were respectively 2.63 × 10⁴lmol^–1cm^–1 and 1.75 × 10^–3 g cm^–2 for SA-DMA and 3.28 × 10⁴lmol^–1 cm^–1 and 1.40 × 10^–3 g cm^–2 for AAP-AN. The concentration factors were 4 and 16 for SA-DMA and AAP-AN, respectively. The detection limits were 0.0138 and 0.0175 g/ml NO₂ ^– for SA-DMA and AAP-AN, respectively. Seven replicate determinations of a solution containing 3.5 g of nitrite gave mean absorbances of 0.410 and 0.500 with relative standard deviations of 0.51 and 0.55% for SA-DMA and AAP-AN, respectively. Interference from various foreign ions has been studied and the methods have been applied to the determination of nitrite in environmental samples.     

Determination of inorganic anions in human saliva by zwitterionic micellar capillary electrophoresis

Capillary electrophoresis (CE) using sulfobetaine-type zwitterionic micelles as the background electrolyte (BGE) has been used to determine inorganic anions in human saliva. The zwitterionic micelles resulted in unique migration behavior for the separation of inorganic anions. They also prevented adsorption of proteins on the inner wall of the capillary. These properties of the zwitterionic micelles enabled the direct determination of inorganic anions in human saliva. Three species of inorganic anions, NO₂ ^–, NO₃ ^–, and SCN^–, were found in real samples and the analysis was achieved within 3 min. Direct UV-absorption was used as the detection method and the detection limits for these anions were 2.0, 1.0, and 5.0 μmol L^–1, respectively (0.09, 0.06, and 0.30 μg mL^–1).     

Determination of inorganic anions in natural water by microcolumn ion chromatography with on-column enrichment.

An on-column enrichment method was developed for the rapid determination of inorganic anions in natural water. The system was assembled from a syringe pump, a six-port switching valve with a sample-enrichment loop, a separation column and a UV detector. The enrichment efficiency of the system was tested by using inorganic anions as samples. The limits of detection were between 0.6 and 7.7 microg/L. The system was applied to the determination of anions in river and pond-water samples.     

Determination of organic acids and inorganic anions in wine by isotachophoresis on a planar chip

Isotachophoretic (ITP) separation and determination of a group of 13 organic and inorganic acids, currently present in wines, on a poly(methyl methacrylate) chip provided with on-column conductivity detection was a subject of a detailed study performed in this work. Experiments with the ITP electrolyte systems proposed to the separation of anionic constituents present in wine revealed that their separation at a low pH (2.9) provides the best results in terms of the resolution. Using a 94 mm long separation channel of the chip, the acids could be resolved within 10-15 min also in instances when their concentrations corresponded to those at which they typically occur in wines. A procedure suitable to the ITP determination of organic acids responsible for some important organoleptic characteristics of wines (tartaric, lactic, malic and citric acids) was developed. Concentrations of 2-10 mg/l of these acids represented their limits of quantitation for a 0.9 microl volume sample loop on the chip. A maximum sample load on the chip, under the preferred separating conditions, was set by the resolution of malate and citrate. A complete resolution of these constituents in wine samples was reached when their molar concentration ratio was 20:1 or less. ITP analyses of a large series of model and wine samples on the chip showed that qualitative indices [RSH (relative step height) values] of the acids, based on the response of the conductivity detector, reproduced with RSD better than 2% while reproducibilities of the determination of the acids of our interest characterized RSD values better than 3.5%.