Effect of groove shape on flow characteristics around a circular cylinder with grooves

In the flow around a circular cylinder, a sudden decrease in the drag force occurs at a high Reynolds number, but the same phenomenon occurs at a lower Reynolds number in the case where there exist grooves or roughness on the circular cylinder surface. In this paper, in order to make clear the flow characteristics around a circular cylinder in the case of changing the shapes of grooves, the drag coefficient, pressure distribution, velocity distribution and turbulent distribution were measured. Moreover the flow around the cylinder was analyzed by applying the RNGk · ∈ turbulent model, and the surface flow pattern was investigated using the oil-film technique. From these results, it is clear that the drag coefficient of a circular cylinder with triangular grooves decreases by about 15% compared with that of a circular cylinder with arc grooves.     

Effect of the number of grooves on flow characteristics around a circular cylinder with triangular grooves

In the flow around a circular cylinder, a sudden decrease in the mean drag coefficient occurs at a high Reynolds number, but the same phenomenon occurs at a lower Reynolds number in the case where there exist grooves or roughness on the cylinder surface. In this paper, in order to make clear the flow characteristics around a cylinder with 20, 26 and 32 triangular grooves, the mean drag coefficient, pressure distribution, velocity distribution and turbulence intensity distribution were measured. Moreover, the flow around the cylinder was analyzed by applying the RNGk − ɛ turbulent model, and the surface flow pattern was investigated using the oil-film technique. From these results, it was found that a sudden decrease in the mean drag coefficient of a cylinder with 32 triangular grooves occurs at a lower Reynolds number compared with 20 and 26 triangular grooves.     

电磁力控制湍流边界层分离圆柱绕流场特性数值分析

在亚临界区高雷诺数Re=1.4×105下,采用脱体涡模拟结合湍流分离的方法对弱电解质中电磁力作用下湍流边界层分离圆柱绕流场及其升(阻)力特性进行了数值模拟和分析.结果表明,电磁力可以提高圆柱体湍流边界层内的流体动能,延缓圆柱体湍流边界层的流动分离,减弱圆柱体湍流绕流场中在流向和展向上大尺度漩涡的强度,减小圆柱体阻力时均值及其升力脉动幅值.当电磁力作用参数大于某个临界值后,湍流边界层流动分离消失,在圆柱体尾部产生射流现象,从而电磁力对圆柱体产生净推力作用,出现负阻力现象,而且升力脉动幅值接近于零,出现圆柱体升力消失现象.     

Flow characteristics around a rotating grooved circular cylinder with grooved of different depths

The present paper describes the flow characteristics around a rotating grooved circular cylinder with grooves of different depths. The surface structure of a circular cylinder was varied by changing the depths of 32 arc grooves on the surface. The surface pressure on the cylinder is measured for theRe range of from 0.4×10⁵ to 1.8×10⁵ and for rotations of from 0 to 4500 rpm. The drag coefficient of a grooved cylinder increases as the spin rate ratio α (= rotational speed of the cylinder surface/uniform velocity) increases forRe>1.0×10⁵. As the groove depth increases, the drag coefficient of a grooved cylinder is independent from the spin rate ratio α. The direction of the lift force of a smooth cylinder is opposite to the Magnus force forRe>1.0×10⁵. However, the direction of the lift force of a grooved cylinder is the same as that of the Magnus force for allRe>1.0×10⁵. As the groove depth increases, the increase in the slope of the lift coefficient becomes small. These phenomena are related to the positions of the flow separation points, which are clarified from the pressure distribution and flow visualization by the spark tracing method. In addition, in the present study, the flow around a rotating grooved cylinder is clarified by flow visualization.     

Flow characteristics around a square cylinder with changing chamfer dimensions

Abstract  

It is known that for a square cylinder subjected to uniform flow, the drag force changes with the angle of attack. To clarify the flow characteristics around a square cylinder with corner cutoffs, we measured the drag coefficient and the Strouhal number for changing chamfer dimensions. We analyzed the flow around a square cylinder with corner cutoffs by applying the RNG k–ε turbulent model, and investigated the surface flow pattern using visualization by means of the oil film and mist flow method. From these results, we obtained the surface flow patterns by the oil film method and numerical analysis. The numerical results agreed well with the experimental values. The drag coefficient of the square cylinder with corner cutoffs decreased suddenly at an angle of attack of about α = 0°– 10° when compared with the drag coefficient for a square cylinder. The minimum value of the drag coefficient for the square cylinder with corner cutoffs decreased by about 30% compared with that for the square cylinder. The drag coefficient of the square cylinder with 10% corner cutoffs was found to be smallest, since the wake area of this square cylinder was smaller compared with that of the other square cylinder.     

Calculations of the flow resistance and heat emission of a sphere in the laminar and high-turbulent gas flows

An early drag crisis can occur at high turbulence of incoming gas flow to a sphere. To study the influence of a crisis on heat transfer from a sphere to gas, a numerical experiment was carried out in which the free gas flow around a sphere with a temperature lower than the sphere temperature was simulated for two cases. The flow was laminar in the first case and highly turbulent in the second case. To take into account turbulence, the kinematic coefficient of turbulent viscosity with a value, which is much higher (up to 2000 times) than that for physical viscosity, was introduced. The results of calculations show that the early drag crisis occurs at Reynolds numbers of about 100 and results in considerable (by four to seven times) decrease in the hydrodynamic force and sphere drag coefficient C _d . The early drag crisis is also accompanied by the crisis of heat transfer from a sphere to gas with a decrease in Nusselt numbers Nu by three to six times.     

尺度自适应模拟和大涡模拟的关联性分析

采用理论分析和数值模拟相结合的方法,系统研究了尺度自适应模拟（scale-adaptive simulation,SAS）和大涡模拟（large-eddy simulation,LES）的关联性问题.在理论分析方面,对比分析了系综平均和滤波的定义、Spalart-Allmaras（SA）湍流模型和动态亚格子（subgrid-scale,SGS）模型关于湍流黏性系数的求解方式.理论分析结果表明,系综平均等价于盒式直接滤波,SAS和LES的控制方程在数学形式上具有一致性;SAS存在过多的湍流耗散,主要来自于SA输运方程中的扩散项.在数值模拟方面,选取来流Mach数0.55,Reynolds数2×105的圆柱可压缩绕流为分析算例.计算结果表明,SAS和LES预测的大尺度平均流场信息几乎一致,SAS预测的湍流脉动信息略低于LES.SAS在圆柱近尾迹区的湍流耗散过大,而在稍远的尾迹区几乎能够完全等效于LES.      

The Oseen drag on a circular cylinder revisited

A scheme is presented to evaluate the drag on an infinite circular cylinder, at rest in a perpendicular uniform stationary flow. This scheme leads already in second approximation to very satisfactory values for the drag coefficient up to Reynolds number R = 10 and probably even up to R = 10².     

A study on drag reduction of a rotationally oscillating circular cylinder at low Reynolds number

The flow field around a rotationally oscillating circular cylinder in a uniform flow is studied by using a particle image velocimetry to understand the mechanism of drag reduction and the corresponding suppression of vortex shedding in the cylinder wake at low Reynolds number. Experiments are conducted on the flow around the circular cylinder under rotational oscillation at forcing Strouhal number 1, rotational amplitude 2 and Reynolds number 2,000. It is found from the flow measurement by PIV that the width of the wake is narrowed and the velocity fluctuations are reduced by the rotational oscillation of the cylinder, which results in the drag reduction rate of 30%. The mechanism of drag reduction is studied by phase-averaged PIV measurement, which indicates the formation of periodic small-scale vortices from both sides of the cylinder. It is found from the cross-correlation measurement between the velocity fluctuations that the large-scale structure of vortex shedding is almost removed in the cylinder wake, when the small-scale vortices are generated at the unstable frequency of shear layer by the influence of rotational oscillation.     

Investigation of turbulent flow past a flagged short finite circular cylinder

This study was conducted to investigate the flow structures of turbulent flow passing over a short finite cylinder in which a rigid flag is attached to the rear of the cylinder, in wake region. The length-to-diameter ratio of the cylinder was chosen to be L/D = 2, whereas the rigid flag had a width-to-diameter ratio of W/D = 1.5. Wall-adapted large-eddy simulation (LES-WALE) was used to resolve unsteady turbulent flow structures. The far field Reynolds number based on cylinder diameter was chosen to be 20,000. The results were compared with the regular case wherein no flag was attached to the cylinder. Results revealed that the flow pattern behind the cylinder with flag was totally different in comparison with the regular case one. However, top free end of the cylinder was not influenced by the flag in contrast with the wake region. At far downstream from the cylinder, most of the flow structures in both cases appeared the same. The horseshoe vortices in both cases appeared to be an unsteady phenomenon, with slightly different patterns. Moreover, in the case of flag attachment, the pressure coefficient was smaller than that of with no flag. Finally, it was shown that the main and secondary Strouhal numbers locations were different in both cases.     

Coherence and Reynolds stresses in the turbulent wake behind a curved circular cylinder

The turbulent wake behind a curved circular cylinder is investigated based on data obtained from a direct numerical simulation. Here, emphasis is placed in the assessment of two approaches for simplified modelling: reduced-order modelling (ROM) and Reynolds-averaged Navier–Stokes equations. To this end, the instantaneous vortical structures, the proper orthogonal decomposition (POD) of the flow, and relevant Reynolds stress components have been analysed. The results show that despite the complexity of the instantaneous vortical structures, the wake dynamics are governed by the quasi-periodic shedding of primary vortices. Between 24% and 50% of the kinetic energy in the POD is captured by the two most energetic modes, and about 200 modes are needed to capture 90% of the kinetic energy. These findings suggest that, as long as the large-scale structures of the von Kármán vortex shedding are concerned, the present case can be approached by ROM; but a detailed representation of the flow dynamics without an eddy viscosity model that accounts for the unresolved turbulent fluctuations would require a large amount of degrees of freedom. Concerning the Reynolds stresses, their magnitude varies considerably depending on the depth at which they have been sampled. This dependence is related to the strength of the vortex shedding, and the intensity of the secondary flows induced by the curvature of the cylinder. As a consequence of the combination of these two effects, the correlation between streamwise and vertical velocity fluctuations is highest in the wake behind the midspan of the curved cylinder, and the correlation between cross-flow and vertical velocity fluctuations reaches large values in the lower wake.     

Handling of temperature dependence of viscosity in problems of incompressible medium flow around a cylinder

The viscous incompressible medium (water, air) flow past a circular cylinder is considered with regard for the temperature T dependent viscosity v. The influence of different boundary conditions for temperature on flow structure, the drag coefficient and its components due to the pressure and viscosity is investigated in the problem of the flow past a cylinder at rest for the (diameter-based) Reynolds number Re_D = 40. A relation between the viscosity gradient along a normal to the body surface and the integral vorticity flux from the body surface into the boundary layer is discussed. Unlike the constant viscosity case the vorticity flux may be different from zero, which must lead because of the integral conservation law for the vorticity to an alteration of the far-field boundary conditions for the velocity. In the same connection, the problem is analysed on the heat spot entry into the computational region under consideration for the flow past a circular cylinder. The examples of the symmetrization of separated flow past a cylinder performing rotation oscillations in a uniform free stream (the Taneda problem) are considered. A comparison with flow computations for low Mach numbers M « 1 for the flow of a medium past a cylinder at rest is carried out. At the computation of the equation for heat transfer under the assumption of incompressibility of such media as air, it is proposed to retain the pressure derivative, which is typical of gases. In this case, a better agreement with the computations of compressible flows (for M « 1) is achieved, for example, at the determination of the sizes of a symmetric zone of flow separation past a circular cylinder. An unsteady flow in the neighborhood of the point of joining the zero streamline bounding a closed region of separated flow (the cavity) in a wake of the cylinder at rest is obtained by a numerical simulation at the Reynolds number equal to 40.     

Calculation of the flow about a sphere and the drag of the sphere under laminar and strongly turbulent conditions

To investigate the influence of a strongly turbulent incoming flow on the hydrodynamic drag of a body and occurrence of the early crisis of drag, a numerical experiment is conducted in which a free gas flow about a sphere is simulated for two cases, namely, for a laminar flow and for a strongly turbulent flow. Turbulence is simulated by assuming a high kinematic coefficient of turbulent viscosity. Calculation data lead us to conclude that the early crisis of drag at Reynolds numbers near 100, which shows up as a considerable (four-to sevenfold) decrease in the hydrodynamic force and the drag coefficient of the body, can be explained by the strong turbulence of the incoming flow.     

均匀流中近壁面垂直流向振荡圆柱水动力特性研究

对均匀来流下靠近壁面处在垂直流向做强迫振荡运动的光滑圆柱的水动力特性进行了试验研究. 试验在拖曳水池中进行, 雷诺数为2× 10⁵, 通过采集顺流向和垂直流向的力, 得到了阻力系数、升力系数、相位角等与间隙比、振荡频率和振幅之间的关系. 通过研究得到如下结论: 1)振荡圆柱的平均阻力系数在近壁面处随间隙比的减小而骤降; 2)振荡圆柱泄涡受到完全抑制的临界间隙比要小于静止圆柱; 3)近壁面的存在对振荡圆柱的能量传递有着重要的影响, 自由边界圆柱强迫振荡所得到的水动力系数不能用来预报海底管道的涡激振动; 4)对于振荡圆柱, 附加质量系数只有在一定的频率范围内才是定值, 且在低频率区域其绝对值随间隙比减小而增大; 5)圆柱在进行强迫振荡时, 其平均阻力系数、振荡阻力系数和振荡升力系数均随无因次振幅的增加而增大. 关键词： 海底管道 强迫振荡 水动力特性 涡激振动     

Experimental verification of the early crisis of drag using a single sphere

The recently discovered phenomenon of drag anomaly (early crisis) observed for droplets in a two-phase turbulent flow at transition Reynolds numbers (Re = 10–100) is experimentally supported in the case of a gas flow about a single hard sphere as well. Using a specially designed torsion balance, the drag force of a foam plastic sphere 3 mm in diameter placed in a blower-produced turbulent jet is measured. It is found that the turbulence of the flow about the sphere must be high for the drag anomaly to arise.     

Experimental study of noise emitted by circular cylinders with large roughness

The aerodynamic noise generated by high Reynolds number flow around a bluff body with large surface roughness was investigated. This is a relevant problem in many applications, in particular aircraft landing gear noise. A circular cylinder in cross-flow and a zero-pressure-gradient turbulent boundary layer with various types of roughness was tested in a series of wind tunnel experiments. It has been shown that distributed roughness covering a circular cylinder affects the spectra over the entire frequency range. Roughness noise is dominant at high frequencies, and the peak frequency is well described by Howe?s roughness noise model when scaled with the maximum outer velocity. There are differences between hemispherical and cylindrical roughness elements for both the circular cylinder and the zero-pressure-gradient turbulent boundary layer cases, indicating a dependence on roughness shape, not described by the considered roughness noise models. Cylindrical roughness generates higher noise levels at the highest frequencies, especially for the zero-pressure-gradient turbulent boundary layer case. Cable-type roughness aligned with the mean flow does not generate roughness noise, and its spectrum has been found to collapse with the smooth cylinder at medium and high frequencies. At low and medium frequencies the noise spectra have the same features as the smooth cylinder, but with higher shedding peak levels and fall-off levels, despite the decrease in spanwise correlation length. Roughness induces early separation, and thus a shift of the spectra to lower frequencies.     

基于间断有限元方法的并列圆柱层流流动特性

基于高阶的间断有限元方法, 数值模拟低马赫数下并列圆柱的可压缩层流流动, 捕捉并列圆柱流场中的漩涡结构, 以便分析并列圆柱尾流的流动特性. 针对二维圆柱的边界形式, 采用曲边三角形单元构造二维圆柱的曲面边界, 以适应高阶离散格式的精度. 在验证方法合理性的基础上, 分析圆柱间距及雷诺数对漩涡脱落及受力特性的影响规律. 研究结果表明: 并列圆柱的间距是影响流场流动特性的一个主要因素, 它会改变圆柱漩涡脱落的形式. 随着圆柱间距的增加, 上下圆柱的平均阻力系数及平均升力系数的绝对值随之显著下降. 雷诺数对于平均阻力系数的影响相对较小. 但随着雷诺数的增加, 上下圆柱的平均升力系数会随之降低, 而漩涡的脱落频率会随之增大.     

Bubbly turbulent drag reduction is a boundary layer effect

In turbulent Taylor-Couette flow, the injection of bubbles reduces the overall drag. On the other hand, rough walls enhance the overall drag. In this work, we inject bubbles into turbulent Taylor-Couette flow with rough walls (with a Reynolds number up to 4 x 10(5), finding an enhancement of the dimensionless drag as compared to the case without bubbles. The dimensional drag is unchanged. As in the rough-wall case no smooth boundary layers can develop, the results demonstrate that bubbly drag reduction is a pure boundary layer effect.     

Direct numerical simulation of transitional flow in a finite length curved pipe

Transition to turbulent flow in a curved pipe has been well studied through experiments and numerical simulations. Numerical simulations often use a helical pipe with an infinite length such that the inlet and outlet boundary conditions can be modelled as periodic which greatly reduces computational time. In this study, we examined a finite length curved pipe with Poiseuille flow imposed at the inlet and a stress-free boundary condition at the outlet. Direct numerical simulation of the Navier-Stokes equations for rigid walls and a Newtonian fluid was performed using nek5000. Straight extensions were added to the inlet and outlet such to diminish the impact of boundary conditions on the flow field in the region with curvature. The examined model has a pipe radius of curvature that is three times the pipe radius. The model has ～355 million nodes and required an order of magnitude greater computational time when compared with an infinite length curved pipe. Results show that the critical Reynolds number, the lowest value with instabilities present in the flow, is much greater than that of a straight pipe and occurs near Re=5000–5200. This is larger than the critical Reynolds number typically reported for an infinite length curved pipe (Re=4200–4300).     

The Oseen drag on a sphere and the method of induced forces

The method of induced forces, which was used previously to derive a scheme for the evaluation of the Oseen drag exerted on a circular cylinder, is applied now to the problem of the Oseen drag experienced by a sphere. By taking into account the zeroth and first force multipole alone, very satisfactory values for the drag coefficient are obtained for Reynolds numbers up to order 10².