Investigation of Ag nanoparticles produced by nanosecond pulsed laser ablation in water

A study is presented of the properties of Ag nanoparticles produced by nanosecond pulsed laser ablation in twice-distilled water. An Ag target was immersed in the liquid and irradiated by the fundamental, second, third and fourth harmonics of a Nd:YAG laser system to create different colloids. Two specific boundary values of the laser fluence were applied for each wavelength. The properties of the nanoparticles at different wavelengths of the laser radiation were examined. The characterization of the colloids was performed immediately after their fabrication. Spherical and spherical-like shapes of the nanoparticles created were established. The formation of nanowires was observed when the second and the third harmonics of the laser were used. It is connected with self-absorption of the incident laser light from the already-created nanoparticles and depends also on the laser fluence. The size distribution of the nanoparticles is estimated by transmission electron microscopy. Generally, their mean size and standard deviation decreased as the wavelength of the incident laser light was increased and increased with the increase of the laser fluence. The substantial discrepancy between the results already commented on for both characteristics considered and others, obtained by dynamic light scattering, is discussed. The structure of the nanoparticles was established to be single and polycrystalline, and the phase composition in both cases is identified as consisting of cubic silver. The nanoparticles are slightly oxidized.     

Investigation of metal nanoparticles produced by laser ablation and their catalytic activity

Polydiphenylsilylenemethylene (PDPhSM) thin films, which are difficult to fabricate by conventional methods because of their insolubility and high melting point, have been synthesized by using laser-ablated metal nanoparticles for the thermal ring-opening polymerization of 1,1,3,3-tetraphenyl-1,3-disilacyclobutane (TPDC) in this paper. TPDC was first evaporated on silicon substrates and then exposed to metal (Pt, Cu and Ag) nanoparticles deposition by laser ablation prior to heat treatment. The catalytic activity of Pt, Cu and Ag nanoparticles has been studied. The results showed that the mean diameter of Pt nanoparticles was the smallest, Cu nanoparticles the moderate and Ag nanoparticles the biggest, while the polymerization efficiency for Pt nanoparticles was the highest, Cu nanoparticles the moderate and Ag nanoparticles the lowest. In addition, the penetration behaviours of Pt, Cu and Ag nanoparticles into the TPDC monomer films during laser ablation were different due to the particle size or the chemical interaction between metal nanoparticles and TPDC molecules.     

ZnO nanoparticles produced by reactive laser ablation

The paper presents the results of theoretical and experimental researches of the analysis of nanopowder ZnO and ZnO-based structures formation mechanisms by means of pulse laser reactive technology (λ = 1.06 μm, τ = 10⁻⁷ to 10⁻⁵ s). The developed 2D model combines non-stationary heat transfer and fluid motion along with the calculated profile of surface deformation. The characteristics of the dispersive and chemical compositions and structural parameters of the synthesized nanopowder together with the influence of the energy of laser impulse evaporation, its duration and gas pressure in the reaction chamber have been studied using X-ray diffractrometry (XRD), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM). Particle size distribution analysis of ZnO has shown that the majority of them range from 5 to 60 nm in size. The photoluminescence emission spectra of the initial ZnO nanopowder at room temperature have been identified.     

Spectroscopic studies of sodium nitrate plasma produced by nanosecond laser ablation

We present the optical emission characteristics of the sodium plasma produced at the surface of sodium nitrate (NaNO₃) also known as Chile saltpeter. We used a Q-switched Nd:YAG (Quantel Brilliant) pulsed laser having a pulse duration of 5?ns and 10?Hz repetition rate which is capable of delivering 400?mJ at 1064?nm and 200?mJ at 532?nm. The target material was placed in front of laser beam in air (atmospheric pressure). The experimentally observed line profiles of neutral sodium have been used to extract the electron temperature using the Boltzmann plot method, whereas the electron number density has been determined from the Stark broadening. The electron temperature is calculated by varying the distance from the target surface along the line of propagation of the plasma plume and also by varying the laser irradiance. Besides, we have studied the variation of number density as a function of laser irradiance as well as its variation with the distance from the target surface. It is observed that electron temperature and electron number density increase as the laser irradiance is increased.     

Iron carbide nanoparticles produced by laser ablation in organic solvent

Laser ablation of iron in an organic solvent (pentane, hexane, or decane) was performed using an air-tight cell to produce iron carbide nanoparticles. M?ssbauer spectra of the nanoparticles were obtained at room temperature. They revealed that the nanoparticles consisted of two paramagnetic components and magnetic components. The two paramagnetic components were a high-spin Fe(II) species and an amorphous iron carbide containing a large amount of carbon. Whereas the magnetic components measured at room temperature exhibited superparamagnetism, those measured at low temperature were fitted by a combination of four sextets, which were assigned to Fe₇ C ₃. The Fe₇ C ₃ yield was higher in higher molecular weight solvents. Transmission electron microscopy (TEM) images of the samples showed that the nanoparticles were spherical with diameters in the range 10–100?nm.     

纳秒激光烧蚀下液态金属表面微结构的形成(英文)

首次发现了在不同保护气体及多脉冲UV-IR激光的照射下,液态金属的微型突起和微结构的形成。测量表明,针对不同的金属和保护气,这种结构的单脉冲生成速率可达(5～20)μm/pulse,形成了长度为1～2 mm,直径约为焦点两倍的单个微型突起。最后,介绍了控制微结构形状的可能性,并讨论了它们的应用潜力。     

纳秒激光烧蚀下液态金属表面微结构的形成

首次发现了在不同保护气体及多脉冲uV—IR激光的照射下,液态金属的微型突起和微结构的形成。测量表明,针对不同的金属和保护气,这种结构的单脉冲生成速率可达（5—20）μm／pulse,形成了长度为1～2mm,直径约为焦点两倍的单个微型突起。最后,介绍了控制微结构形状的可能性,并讨论了它们的应用潜力。     

Metal-on-oxide nanoparticles produced using laser ablation of microparticle aerosols

A continuous aerosol process has been studied for producing nanoparticles of oxides that were decorated with smaller metallic nanoparticles and are free of organic stabilizers. To produce the oxide carrier nanoparticles, an aerosol of 3–6 μm oxide particles was ablated using a pulsed excimer laser. The resulting oxide nanoparticle aerosol was then mixed with 1.5–2.0 μm metallic particles and this mixed aerosol was exposed to the laser for a second time. The metallic micron-sized particles were ablated during this second exposure, and the resulting nanoparticles deposited on the surface of the oxide nanoparticles producing an aerosol of 10–60 nm oxide nanoparticles that were decorated with smaller 1–5 nm metallic nanoparticles. The metal and oxide nanoparticle sizes were varied by changing the laser fluence and gas type in the aerosol. The flexibility of this approach was demonstrated by producing metal-decorated oxide nanoparticles using two oxides, SiO₂ and TiO₂, and two metals, Au and Ag.     

Synthesis of nanoparticles by pulsed laser ablation of consolidated metal microparticles

This paper describes a novel process of nanoparticle synthesis by pulsed laser ablation of consolidated microparticles. Metal microparticles, including Cu, Al and Ag, are consolidated by a cold isobaric press with pressures up to a few hundred MPa before laser irradiation. Nanoparticles are then synthesized in air by high-power pulsed laser ablation of the microparticles using a Q-switched Nd:YAG laser. It is shown that the degree of compaction plays a significant role in determining the size of the produced nanoparticles. The effect of laser fluence and collector position on the distribution of particle size is examined. Photoacoustic deflection probing and nanosecond time-resolved visualization indicate that the novel process attains increased efficiency of laser-energy coupling with the target. PACS 81.07.-b; 81.07.Wx; 42.62.Cf     

Characterization of gaseous phase and nanoparticles produced in ultra-short pulsed laser ablation of transition metal borides

The plasma produced by ultra-short laser ablation of ZrB₂ and ReB₂ has been studied by ICCD imaging and time and space resolved optical emission spectroscopy. The aim was to clarify the mechanism of deposition leading to the morphology and composition found in the deposited films. The results indicate that for all systems the film characteristics are compatible with a deposition mechanism involving a growth from nanoparticles, ejected directly from the target, whose composition can be interpreted in terms of equilibrium vaporization during the flight from the target to the substrate.     

Chemical analysis of products obtained by nanosecond laser ablation

The chemical analysis of a laser jet was performed with a combination of laser back mass transfer and X-ray photoelectron spectroscopy (XPS). It was revealed that, as compared to the source material, films deposited from the jet under laser mass transfer in air show increased oxidizability and changed chemical composition.     

Characterization of Ag and Au nanoparticles created by nanosecond pulsed laser ablation in double distilled water

Pulsed laser ablation of Ag and Au targets, immersed in double-distilled water is used to synthesize metallic nanoparticles (NPs). The targets are irradiated for 20 min by laser pulses at different wavelengths—the fundamental and the second harmonic (SHG) (λ = 1064 and 532 nm, respectively) of a Nd:YAG laser system. The ablation process is performed at a repetition rate of 10 Hz and with pulse duration of 15 ns. Two boundary values of the laser fluence for each wavelength under the experimental conditions chosen were used—it varied from several J/cm² to tens of J/cm². Only as-prepared samples were measured not later than two hours after fabrication. The NPs shape and size distribution were evaluated from transmission electron microscopy (TEM) images. The suspensions obtained were investigated by optical transmission spectroscopy in the near UV and in the visible region in order to get information about these parameters. Spherical shape of the NPs at the low laser fluence and appearance of aggregation and building of nanowires at the SHG and high laser fluence was seen. Dependence of the mean particle size at the SHG on the laser fluence was established. Comments on the results obtained have been also presented.     

Gold nanoparticles produced by laser ablation in water and in graphene oxide suspension

The comparison between two different approaches based on the use of the laser ablation in medium to synthetise gold nanoparticles is presented and discussed. Deionised water as well as a graphene oxide (GO) suspension in deionised water have been employed as solution to produce gold nanoparticles by laser ablation. In the former case, the nanoparticles assembly has been stabilised by using surfactants, but in the latter case to avoid undesired effects the use of chemicals was not necessary and Au reduced graphene oxide (Au-rGO) nanocomposites have been obtained. The structure, size and composition of the gold nanoparticles and of the Au–rGO nanocomposites have been monitored by UV–Vis–NIR absorption spectroscopy and Raman spectroscopy, the transmission and scanning electron microscopies and the X-ray energy-dispersive spectroscopy. The presented methodology of Au rGO nanocomposites preparation could represent a green alternative on the production of metallic nanoparticles in biocompatible environment.     

Fabrication of black multicrystalline silicon surface by nanosecond laser ablation

The optimal regimes for uniform texturing of a multicrystalline silicon (mc-Si) surface by pulsed laser radiation have been determined. The morphology and reflectance spectra of the texturized mc-Si have been studied. The laser-texturized mc-Si samples with reflectance of 2?C3% over a wide spectral region have been produced. The influence of subsequent chemical etching on the reflective properties of the texturized surface has been analyzed.     

Periodic patterning of silicon by direct nanosecond laser interference ablation

The production of periodic structures in silicon wafers by four-beam is presented. Because laser interference ablation is a single-step and cost-effective process, there is a great technological interest in the fabrication of these structures for their use as antireflection surfaces. Three different laser fluences are used to modify the silicon surface (0.8 J cm⁻², 1.3 J cm⁻², 2.0 J cm⁻²) creating bumps in the rim of the irradiated area. Laser induced periodic surface structures (LIPSS), in particular micro and nano-ripples, are also observed. Measurements of the reflectivity show a decrease in the reflectance for the samples processed with a laser fluence of 2.0 J cm⁻², probably caused by the appearance of the nano-ripples in the structured area, while bumps start to deteriorate.