Evaluation of surface kinetic data by the transform analysis of modulated molecular beam measurements

The merits of different modulated molecular beam detection systems are discussed and the application of modern data handling methods described. It is shown that by using time domain analysis together with fourier transform techniques, information on the kinetics of surface processes is obtained. Data at a number of excitation frequencies is obtained in a single experiment. A means of detecting non-linear surface processes, and an accurate method for the determination of reaction orders is given. The origin of spurious coherent signals is considered, and finally the application of the techniques is illustrated with data obtained from an investigation of the interaction of modulated As₄ beams with GaAs surfaces.     

X‐ray spectra by means of Monte Carlo simulations for imaging applications

X‐ray tubes have a broad range of applications worldwide, including several techniques for atomic physics, like X‐ray fluorescence, as well as for medical imaging, like computed tomography. The performances of X‐ray imaging detectors have shown to be significantly sensitive to the incident beam spectrum. Therefore, an accurate knowledge of the X‐ray beam becomes necessary for the emission source characterization and the whole imaging process comprehension. Direct measurements and suitable Monte Carlo simulations may be used to establish the X‐ray spectra. Dedicated Monte Carlo simulation routines, based on the PENELOPE code, have been developed to determine the Bremsstrahlung X‐ray spectra generated by conventional X‐ray tubes. The simulated spectra have been validated by comparison with the corresponding experimental data showing an overall good agreement. The incorporation of a suitably designed virtual grid allowed to assess the angular distribution of Bremsstrahlung yield, showing a remarkable anisotropy. In addition, a dedicated program has been developed for virtual imaging, which enables to perform suitable X‐ray absorption contrast images. Also, the developed program includes a user‐friendly graphic interface to allow the upload of required input parameters, which include setup arrangement, beam characteristics, sample properties and image simulation parameters (spatial resolution, tracks per run, etc.). The software includes dedicated subroutines which handle the physical process from X‐ray generation up to detector signal acquisition. The aim of the developed program is to perform virtual imaging by means of absorption contrast and using conventional X‐ray sources, which may be a useful tool for the study the X‐ray imaging techniques in several research fields as well as for educational purposes. The performed comparisons with experimental data have shown good agreement. The obtained results for X‐ray imaging may constitute useful information for the comprehension and improvement of X‐ray image quality, like absorption contrast optimization, detail visualization, definition and detectability. Copyright © 2010 John Wiley & Sons, Ltd.     

X‐ray reflectivity from curved liquid interfaces

X‐ray reflectivity studies of the structure of liquid–vapour and liquid–liquid interfaces at modern sources, such as free‐electron lasers, are currently impeded by the lack of dedicated liquid surface diffractometers. It is shown that this obstacle can be overcome by an alternative experimental approach that uses the natural curvature of a liquid drop for variation of the angle of incidence. Two modes of operation are shown: (i) sequential reflectivity measurements by a nanometre beam and (ii) parallel acquisition of large ranges of a reflectivity curve by micrometre beams. The feasibility of the two methods is demonstrated by studies of the Hg/vapour, H₂O/vapour and Hg/0.1 M NaF interface. The obtained reflectivity curves match the data obtained by conventional techniques up to 5α_c in micro‐beam mode and up to 35α_c in nano‐beam mode, allowing observation of the Hg layering peak.     

Design and acoustic characterization of limited diffraction ultrasonic devices

Limited diffraction ultrasonic transducers are devices that have a large depth of acoustic field without important effects of diffraction, which make them optimal in applications of medical images, among others. This report details how this special type of piezoelectric device was designed by means of a simple technology using three electrodes in the form of concentric rings in both faces of a ferroelectric ceramic disk, which were used to apply a profile of non-homogeneous polarization. Once designed, the radiation fields emitted by these resonators were characterized experimentally by electro-acoustic and acousto-optic techniques and were compared with those emitted by conventional devices. As shown in the experimental characterizations, ultrasonic transducers with optimal properties for use in medical applications such as good collimation of the ultrasound beam, high lateral resolution, as well as little effects of diffraction were obtained.     

Plasma-Beam-Hole Interaction

Highly energetic and dense plasma beams obtained by an improved version of a coaxial gun were directed towards a perforated metallic plate to study plasma-hole interactions. The features of the escaping plasma jet were studied by means of the method of characteristics applied to a single fluid flow. The incident plasma beam and the characteristics of the escaping jet were investigated by means of various diagnostic techniques. Observations provided evidence that a large amount of material was ablated from the hole region and transported by the escaping jet.     

Diagnostic system for two dimension intensity distribution of laser beam

The diagnostic system for two dimension(2-D)intensity distribution of laserbeam is a measuring instrument for many parameters of laser beam.2-D intensity distributionplot of laser beam is obtained by the two dimension scanning mirror which is controlled by amicrocomputer to scan the laser beam on a detector.Many parameters of laser beam such asthe isointensity distribution plot,the beam diameter,the beam waist diameter,the laser pow-er,the diverge angle and the beam brightness,are given by means of the microcomputer pro-cessing the data measured.Theoretical analysis of beam parameter transform is given.     

基于波导管的无缝扫描光刻激光均束设计

351nm波长的准分子激光器由光波导管作为激光均束器,直接输出正六角形均匀分布的照明光束,能在大面积激光投影光刻中实现无缝扫描。同目前常用的微透镜阵列器相比制作简单,无须光阑就能直接获取所需要的六角形光束,减少了能量损失。通过合理的假设和理论推算,依据管内最大反射次数就能适当地选取光波导管的长度,既保证了足够的反射次数以维持良好的均匀性,同时又避免了不必要的管长所带来的更多反射损耗。利用ZEMAX光学设计软件模拟和分析了由光波导管输出的照明光。结果表明,输出的六角形光束的相对光通量为96%,近似于平顶的能量分布,呈现出了极好的均匀性。     

Control of the pulse width of a laser-diode end-pumped passively Q-switched solid-state laser

We theoretically and experimentally study different techniques to control the pulse width of a laser-diode-pumped passively Q-switched solid-state laser. It is shown that varying the laser beam radius in the saturable absorber and the pump beam radius in the gain medium provide an efficient means to control the pulse width. The experiments performed on a laser-diode-pumped Nd:YVO₄ laser passively Q-switched by a Cr⁴⁺:YAG saturable absorber are consistent with the theoretical calculations obtained from the rate-equations model, in which the intracavity photon density is assumed to be Gaussian spatial distribution, and the longitudinal variation of the intracavity photon density and the pump beam spatial distribution are also considered.     

Small-signal analysis of a rectangular helix structure traveling-wave-tube

This paper investigates the properties of traveling wave-beam interaction in a rectangular helix traveling-wave-tube (TWT) for a solid sheet electron beam. The `hot' dispersion equation is obtained by means of the self-consistent field theory. The small signal analysis, which includes the effects of the beam parameters and slow-wave structure (SWS) parameters, is carried out by theoretical computation. The numerical results show that the bandwidth and the small-signal gain of the rectangular helix TWT increase as the beam current increases; and the beam voltage not obviously influences the small signal gain. Among different rectangular helix structures, the small-signal gain increases as the width of the rectangular helix SWS increases, however, the bandwidth decreases whether structure parameters a and L or ψ and L are fixed or not. In addition, a comparison of the small-signal gain of this structure with a conventional round helix is made. The presented analysis will be useful for the design of the TWT with a rectangular helix circuit.     

Frequency analysis of finite beams on nonlinear Kelvin-Voight foundation under moving loads

The vibration of an Euler-Bernoulli beam, resting on a nonlinear Kelvin-Voight viscoelastic foundation, traversed by a moving load is studied in the frequency domain. The objective is to obtain the frequency responses of the beam and the effects of different parameters on the system response. The parameters include the magnitude and speed of the moving load and the foundation nonlinearity and its damping coefficient. The solution is obtained by using the Galerkin method in conjunction with the multiple scales method (MSM). The governing nonlinear partial differential equations of motion are discretized into sets of nonlinear ordinary differential equations. Subsequently, the solution is calculated for different harmonics by using the MSM as one of the powerful perturbation techniques. The steady-state responses of the main harmonic as well as its two super-harmonics are then obtained. As a case study, a conventional railway track is dynamically simulated and the jump phenomenon in the response is observed for three harmonics. Moreover, a thorough stability analysis of the system is carried out.     

液芯光纤喇曼光谱的研究

本文叙述了利用液芯光纤技术获得最佳自发喇曼光谱的方法和条件。用16mW He-Ne激束为泵光浦源,获得了较高强度的溴苯自发喇曼光谱。首次用测量喇曼信号强度的方法,计算出光纤衰损系数α,从而获得了最大喇曼光谱所对应的最佳光纤长度。本文以15OmW Ar离子(488nm)激光器为光源,用Spex1403喇曼系统,得到了丰富的溴苯喇曼光谱,比用普通方法获得的喇曼光谱强度高两个数量级。实验结果与理论计算基本符合。     

A simple white beam neutron diffraction technique

White beam neutron diffraction by time-of-flight (TOF) technique has been studied over a number of years as it is believed to be the most convenient method to investigate solids in a fixed geometry. This technique needs a pulsed neutron source and a suitable multichannel, analysing system. The entire system is in general, mechanically quite intricate and expensive. We have investigated an alternative technique to achieve the end result of a constant geometry around the diffracting sample. This involves the use of a single crystal as an analyser to study diffraction pattern from the sample bathed in a white beam and diffracting at any fixed scattering angle. In this paper we report the results of our investigations and have compared this technique with other diffraction techniques. Taking Si, KCl and KNO₃ as typical specimens we have illus. trated the results of our technique and we find that the results are comparable to those obtained by conventional neutron diffraction and TOF diffraction. The technique is simple in mechanical design and data acquisition. It can be easily adapted for high pressure diffraction which is being attempted.     

Laser beam homogenization: Modeling and comparison with experimental results

Beam shaping and homogenization techniques are essential to optimize a large number of laser-material processing applications and laser-material interaction studies. In this paper, we present an innovative approach for modeling laser beam homogenization by means of the integration method. The numerical results are compared with experimental data, and the influence of the measurement technique is discussed. The enhancement of the homogenization capability using an asymmetric divider is also presented and discussed.     

New solid-state lasers and their application potentials

In recent years, Nd:YAG-lasers have found increasing interest in many fields of high-power applications that formerly had been the domain of CO₂-lasers. This was mainly due to several consequences of their wavelength, such as a higher absorptivity, lower sensitivity against laser-induced plasmas and, in particular, the use of flexible glass fibres for beam handling. Disadvantages like poor beam quality and low efficiency are being effectively reduced by recent developments of diode-pumped systems. Some promising concepts based on different pumping techniques and crystal geometries — rods, discs, fibres — will be discussed in view of attainable beam quality and means of power scaling. The second part of the paper will deal with investigations aimed at utilizing the beneficial properties of Nd:YAG-lasers, especially for welding. In particular, the advantages of the twin-focus technique are discussed in some detail with regard to power scaling, process improvements and flexibility increase. Based upon experience, the extension to a multi-focus technique is proposed by presenting experimental data obtained with lamp-pumped high-power lasers and results of numerical modelling. This evidence demonstrates the potential for industrial applications and provides an idea of what can be expected from the new generation of diode-pumped solid-state lasers with high beam quality.     

Boundary conditions for the bending of a piezoelectric beam

For beam bending in transversely isotropic piezoelectric media, the reciprocal theorem and the general solution of piezoelasticity are applied in a novel way to obtain the appropriate stress and mixed boundary conditions accurate to all orders for the beam of general edge geometry and loadings. By generalizing the method developed by Gregory and Wan, a set of necessary conditions on the edge-data for the existence of a rapidly decaying solution is established. The prescribed edge-data of the beam must satisfy these conditions in order that they could generate a decaying state within the beam. When stress and mixed conditions are imposed on the beam edge, these decaying state conditions for the case of bending deformation of piezoelectric beam are derived explicitly. They are then used for the correct formulation of boundary conditions for the beam theory solution (or the interior solution). Besides, an analytical solution of elastic beam is formulated to verify validity of our boundary conditions. For the stress data, our boundary conditions coincide with those obtained in conventional forms of beam theories. More importantly, the appropriate boundary conditions with two sets of mixed edge-data are obtained for the first time.     

Studies of classical radiation emission from plasma wave undulators

The authors examine the characteristics of the classical radiation emitted by a relativistic electron beam that propagates perpendicularly through a large amplitude relativistic plasma wave. Such a study is useful for evaluating the feasibility of using relativistic plasma waves as extremely short wavelength undulators for generating short wavelength radiation. The electron trajectories in a plasma wave undulator are obtained using perturbation techniques and are then compared to numerical simulation results. The frequency spectrum and angular distribution of the spontaneous radiation emitted by a single electron and the stimulated radiation gain are obtained analytically, and are then compared to 3-D numerical simulations. The characteristics of the plasma wave undulator are compared to the AC free-electron laser (FEL) undulator and the conventional FEL     

Photoacoustic saturation spectra of some semiconducting group IV-A transition metal dichalcogenides

Photoacoustic saturation spectra in some semiconductors as HfSe₂, ZrS₂ and HfS₂ have been measured at energies above the fundamental absorption edge, where the photoacoustic signal is independent of the optical coefficient and the dips detected in the photoacoustic spectra may be ascribed to optical reflection effects inherent to the band structure. The comparison between our experimental data and those obtained by means of conventional and modulatory spectroscopic techniques proves that such method is a useful tool in order to determine the electronic structure of photoacoustically active semiconductors.     

Characterisation of a megavoltage linear accelerator Bremsstrahlung by means of Monte Carlo simulations

This work presents a method for megavoltage X‐ray Bremsstrahlung assessment by means of Monte Carlo (MC) (PENELOPE) simulations. The proposed method provides suitable spectrum characterisation by means of a few parameters, namely the acceleration potential and incident angle of electron beam on the anode. The obtained spectra have been used as incident beam for in‐depth dose distribution determination with the aim of performing further comparisons with experimental data. This comparison procedure has been employed for Bremsstrahlung assessment optimisation. Once the Linac Bremsstrahlung is well established, it may be used as incident beam for further dosimetric purposes, such as spatial dose distribution calculations. The whole process has been applied for the characterisation of the megavoltage Bremsstrahlung from a typical Linac, namely the 10 MV Varian Clinac 18. The obtained results for in‐depth dose distributions, when compared with experimental measurements, show an overall good agreement, which may suggest the feasibility of the method. Copyright © 2010 John Wiley & Sons, Ltd.     

Measuring laser divergence

A standard method of measuring the divergence is to measure the beam diameter in the focal plane of a lens based on the proposition that the beam diameter is equal to the focal length of the lens multiplied by the incident beam divergence. The proof of the proposition is relatively easy by geometric optics. Proof of the proposition for a laser beam provides insight into the application of the mode matching formulae. The mode matching formulae provide a ready means of choosing a lens to match one mode to another where the data for both modes is known. The results obtained here allow ready application to the more general case of calculating the output mode for a known input mode and a given focal length.