The reversible addition-fragmentation chain transfer （RAFT） miniemulsion polymerization of vinyl acetate mediated by xanthate

The reversible addition-fragmentation chain transfer(RAFT) miniemulsion polymerization of vinyl acetate(VAc) mediated by methyl(methoxycarbonothioyl) sulfanyl acetate(MMSA) was carried out.The results showed that polymerizations initiated by AIBN and KPS proceeded in a controlled way.The RAFT miniemulsion polymerization of VAc initiated by KPS showed the shorter inhibition period,higher propagation rate coefficient and final conversion than those in experiment initiated by AIBN.When the monomer conversio...     

Preparation of polystyrene/silica nanocomposites by radical copolymerization of styrene with silica macromonomer

A two-stage process has been developed to generate the silica-based macromonomer through surface-modification of silica with polymerizable vinyl groups. The silica surfaces were treated with excess 2,4-toluene diisocynate (TDI), after which the residual isocyanate groups were converted into polymerizable vinyl groups by reaction with hydroxypropylacrylate (HPA). Thus, polystyrene/silica nanocomposites were prepared by conventional radical copolymerization of styrene with silica macromonomer. The main effecting factors, such as ratios of styrene to the macromonomer, together with polymerization time on the copolymerization were studied in detail. FTIR, DSC and TGA were utilized to characterize the nanocomposites. Experimental results revealed that the silica nanoparticles act as cross-linking points in the polystytene/silica nanocomposites, and the glass transition temperatures of the nanocomposites are higher than that of the corresponding pure polystyrene. The glass transition temperatures of nanocomposites increased with the increasing of silica contents, which were further ascertained by DSC.     

Carprofen-imprinted monolith prepared by reversible addition–fragmentation chain transfer polymerization in room temperature ionic liquids

To obtain fast separation, ionic liquids were used as porogens first in combination with reversible addition–fragmentation chain transfer (RAFT) polymerization to prepare a new type of molecularly imprinted polymer (MIP) monolith. The imprinted monolithic column was synthesized using a mixture of carprofen (template), 4-vinylpyridine, ethylene glycol dimethacrylate, [BMIM]BF₄, and chain transfer agent (CTA). Some polymerization factors, such as template-monomer molar ratio, the degree of crosslinking, the composition of the porogen, and the content of CTA, on the column efficiency and imprinting effect of the resulting MIP monolith were systematically investigated. Affinity screening of structurally similar compounds with the template can be achieved in 200 s on the MIP monolith due to high column efficiency (up to 12,070 plates/m) and good column permeability. Recognition mechanism of the imprinted monolith was also investigated.     

Polypropylene wax (PPw)/silica hybrid by in situ non-aqueous sol–gel process for preparation of PP/silica nanocomposites

This paper presented a novel approach to prepare PP/silica nanocomposites. First, PPw-g-KH570 (γ-methacryloxypropyl trimethoxysilane) was obtained by pre-irradiation grafting method and characterized by FTIR and TGA. Then the non-aqueous sol–gel gelation kinetics of TEOS (tetraethoxysilane)-formic acid system in xylene was researched. Subsequently PPw/silica hybrid was obtained by in situ non-aqueous sol–gel reaction of TEOS in the presence of PPw-g-KH570 solution in xylene. Finally PP/silica nanocomposites were prepared by blending of PP matrix and PPw/silica hybrid. The mechanism of in situ formed PPw/silica hybrid was proposed. The morphology of PPw/silica hybrid and microstructures of PP/silica nanocomposites were characterized by TEM and SEM. The mechanical and thermal properties of PP/silica nanocomposites were also well studied by tensile tests and DSC. It was showed that the nanosilica particles were well dispersed in PPw/silica hybrid with the aid of grafting KH570 due to co-condensation by grafted KH570 and TEOS. PPw/silica hybrid was well dispersed in PP matrix with good compatibility and strong interactions. The resulted PP/silica nanocomposites possessed better performance than that of pure PP matrix.     

Synthesis and characterization of poly(ɛ-caprolactone)/Fe3o4 nanocomposites by in situ polymerization

A series of magnetic nanocomposites based on poly(?-caprolactone) (PCL) and Fe₃O₄ nanoparticles were prepared using a facile in situ polymerization method. The chemical structures of the PCL/Fe₃O₄ nanocomposites were characterized by Fourier transform infrared (FTIR) spectroscopy. Results of wide-angle X-ray diffraction (WAXD) showed that the incorporation of the Fe₃O₄ nanoparticles did not affect the crystallization structure of the PCL. Both scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the morphology and dispersion of the Fe₃O₄ nanoparticles within the as-synthesized nanocomposites. Results of differential scanning calorimetry (DSC) and polarizing optical microscopy (POM) showed that the crystallization temperature was raised and the spherulites size decreased by the presence of Fe₃O₄ nanoparticles in the nanocomposites due to the heterogeneous nucleation effect. The thermal stability of the PCL was depressed by incorporation of Fe₃O₄ nanoparticles from thermogravimetric analysis (TGA). The superparamagnetic behavior of the PCL/Fe₃O₄ nanocomposites was testified by the superconducting quantum interference device (SQUID) magnetometer analysis. The obtained biodegradable nanocomposites will have a great potential in magnetic resonance imaging contrast and targeted drug delivery.     

A novel approach for preparation of “cage-like” multihollow polymer microspheres through sulfonated polystyrene particles

A new and effective process has been developed for fabrication of novel cage-like multihollow polymer particles by using sulfonated polystyrene (SP) particles as the templates, with heptane as the phase separation agent, in an ethanol/water medium. The ratio of water/ethanol and the heating temperature play important roles in the formation of these multihollow particles. It was found that the cage-like polymer particles could be obtained when the ratio of ethanol/water is 5:5 (w/w), with a temperature above 50?°C. After a detailed study, the formation mechanism was proposed based on an SP swollen (ethanol and heptane penetrating process) and phase separation process. This new method for fabricating the cage-like multihollow polymer particles has a great meaning not only on confirming the formation mechanism, but also on providing an effective way to prepare the special hollow core/porous shell polymer particles, which could have wide range of potential applications, such as catalysts, sensors, and drug release.     

Molecularly imprinted polymer coated solid-phase microextraction fiber prepared by surface reversible addition–fragmentation chain transfer polymerization for monitoring of Sudan dyes in chilli tomato sauce and chilli pepper samples

Surface reversible addition-fragmentation chain transfer (RAFT) polymerization method was firstly applied to the preparation of molecularly imprinted polymer (MIP) coated silicon solid-phase microextraction (SPME) fibers. With Sudan I as template, an ultra-thin MIP coating with about 0.55-μm thickness was obtained with homogeneous structure and controlled composition, due to the controllable radical growing and chain propagation in surface RAFT polymerization. The MIP-coated fibers were found with enhanced selectivity coefficients (3.0–6.5) to Sudan I–IV dyes in contrast with those reported in our previous work. Furthermore, the ultra-thin thickness of MIP coating was helpful to the effective elution of template and fast adsorption/desorption kinetics, so only about 18 min was needed for MIP-coated SPME operation. The detection limits of 21–55 ng L⁻¹ were achieved for four Sudan dyes, when MIP-coated SPME was coupled with liquid chromatography (LC) and mass spectrometry (MS) detection. The MIP-coated SPME–LC–MS/MS method was tested for the monitoring of ultra trace Sudan dyes in spiked chilli tomato sauce and chilli pepper samples, and high enrichment effect, remarkable matrix peaks-removing capability, and consequent high sensitivities were achieved to four Sudan dyes.     

Polybenzoxazine–silica (PBZ–SiO2) hybrid nanocomposites through in situ sol–gel method

New type of Polybenzoxazine–silica (PBZ–SiO₂) hybrid nanocomposites was prepared through in situ sol–gel method. Benzoxazine was synthesized using bisphenol-A, trans-4-aminocyclohexanol hydrochloride and formaldehyde solution through Mannich condensation reaction and was characterized by FT-IR, ¹HNMR and ¹³CNMR spectroscopy. The methodology adopted in the present study involves to formation of hydrogen bond interaction between the benzoxazine monomer and the silica matrix, followed by the ring opening polymerization of benzoxazine monomer through thermal curing to obtain a red brown transparent PBZ–SiO₂ hybrid. The formation of hybrid nanocomposites was confirmed by FT-IR. Thermal and morphological properties of the hybrid materials were investigated by the differential scanning calorimetry (DSC), thermo gravimetric analysis (TGA), scanning electron microscopy (SEM). The PBZ–SiO₂ hybrids show improved thermal properties and glass transition (Tg) temperature. The nitrogen porosimetry study was carried out to confirm the nanometer level integration of polybenzoxazine in the PBZ–SiO₂ hybrid nanocomposites.     

Dynamics of α and α′ relaxation in layered silicate/polystyrene nanocomposites studied by anelastic spectroscopy

The dynamics of polymer chains in layered silicate/polystyrene nanocomposites was studied by anelastic spectroscopy. Two thermal activated peaks (α and α′ peaks) appeared when the specimens were heated to a high temperature and they were related to glass transition and liquid-liquid transition, respectively. The activation energy was calculated based on Arrhenius equation and it showed that the activation energy of glass transition (E _g) is much higher than that of liquid-liquid transition (E _ll). Furthermore, the most interesting result for the activation energy was that there were two contrary trends for E _g and E _ll, E _g decreased and E _ll increased with the addition of clay platelets. The fragile parameter was analyzed and the variation of fragile parameters for the two transitions was also contrary to each other with the addition of clay platelets. All the results indicated that the confinement effect of clay platelets on the dynamics of polymer chain was scale dependent, and perhaps, the two transitions were produced by different mechanisms.     

Polymethacrylamide—An underrated and easily accessible upper critical solution temperature polymer: Green synthesis via photoiniferter reversible addition–fragmentation chain transfer polymerization and analysis of solution behavior in water/ethanol mixtures

Within the group of stimuli-responsive, “smart” materials, upper critical solution temperature (UCST) polymers remain sparsely investigated. Thus, this work focusses on a vastly ignored UCST polymer: polymethacrylamide (PMAAm). A cost-efficient photoiniferter reversible addition–fragmentation chain transfer (RAFT) polymerization yielding narrowly dispersed (Đ < 1.1) PMAAm is presented. This PMAAm exhibits highly thermoreversible UCST-type phase transitions (PT) in water/ethanol mixtures (ethanol content: 17–35 wt%) which are investigated via temperature dependent dynamic light scattering (DLS). Apart from the ethanol content, the PT temperature is affected by polymer mass fraction and chain length and varies between 10–80 °C depending on the three mentioned parameters. Lastly, PMAAm's propensity towards amide hydrolysis and concomitant PT-suppression is investigated. Below temperatures of 40 °C, PMAAm solutions show no sign of amide hydrolysis for at least three days, however, if heated to 70 °C, the thermoresponsiveness gradually degrades within hours.     

SANS study of hybrid silica aerogels under “in situ” uniaxial compression

We have modified the inorganic silica network of aerogels with polydimethylsiloxane (PDMS), a hydroxyl-terminated polymer, to obtain an organic modified silicate (ORMOSIL). Reactions were assisted by high-power ultrasounds. The resulting gels were dried under supercritical conditions of the solvent to obtain a monolithic sono-aerogel. The mechanical behaviour of these aerogels can be tuned from brittle to rubbery as a function of the organic polymer content. In order to determine the links between the mechanical behaviour and modifications made to the microstructure, SANS (small-angle neutron scattering) experiments were carried out. To measure the intensities under “in situ” uniaxial compression of the aerogel, a specific sample-holder was built. Under uniaxial compression the 2D-diagrams were significantly anisotropic (butterfly pattern), indicating the rearrangement of the polymer. The form factor of these aerogels is described well by two correlation lengths, small microporous silica clusters surrounded by entangled polymer chains of 6 nm average size (blobs), which form a larger secondary level of agglomerates governed by the “frozen-in” elastic constraints.     

A facile rheological approach for the evaluation of “super toughness point” of compatibilized HDPE / MWCNT nanocomposites

Fast and efficient determination of the optimal mechanical property of a polymer/CNT nanocomposite is crucial to develop polymer conductive nanocomposites. This work establishes a rheological approach to evaluate the super-toughness point of compatibilized high density polyethylene (HDPE)/multi-walled carbon nanotube (MWCNT) nanocomposites. Results illustrate that three types of HDPE/MWCNT nanocomposites exhibit obvious gel plateaus in the dynamic rheological curves and the gel points of nanocomposites with compatibilizer shift to the low MWCNTs loading. The super-toughness points of HDPE/MWCNT nanocomposites with compatibilizers show the correspondence with the gel points acquired from the rheological data, indicating that dynamic rheology is an effective way to determine the super-toughness points of HDPE/MWCNT nanocomposites with compatibilizers. Furthermore, unique network structure at the gel points is directly observed and the new mechanism of toughness is proposed. This study provides new insights for effective control of the structures and properties of polymer/CNT nanocomposites.     

Phosphorylated silica/polyamide 6 nanocomposites synthesis by in situ sol–gel method in molten conditions: Impact on the fire-retardancy

Polyamide 6 (PA6)/phosphorylated silica nanocomposites were synthesized during PA6 extrusion through in situ formation of the inorganic phase without solvent. This synthesis is based on the hydrolysis-condensation reactions of diethylphosphatoethyltriethoxysilane (SiP) as a functional inorganic precursor in combination with or without tetraethoxysilane (TEOS) dispersed in the molten PA6. This synthesis is carried out during PA 6 matrix extrusion that means at high temperature and under shear. The characterization of the in situ synthesized PA6/phosphorylated silica nanocomposites by solid ²⁹Si Nuclear Magnetic Resonance (NMR), Small Angle X-ray Scattering (SAXS) and Transmission Electron Microscopy (TEM) coupled with Energy Dispersive X-ray spectroscopy (EDX) demonstrated the possibility to directly create in less than 5 min at 220 °C a phosphorylated silica uniformly dispersed in the PA6, i.e. in the form of well dispersed particles or aggregates of sub-micron range. The influence of silicon and phosphorus on the thermal and fire retardant behaviour was investigated by thermogravimetric analysis (TGA), cone calorimeter and UL94 tests. The fire retardant behaviour was modified with a formation of a char and a peak heat release rate (PHRR) decrease by more than 50% for the SiP based nanocomposite compared to the pure PA6.     

Encapsulation of aluminum flakes with hybrid silica/poly(acrylic acid) nanolayers by combination of sol–gel and in situ polymerization methods: a corrosion behavior study

A combination of sol–gel method and in situ polymerization was used to form a hybrid silica/poly(acrylic acid) nanolayer for the corrosion protection of aluminum pigments. To this end, the pigment particles were first coated with a silica layer by sol–gel method. Tetraethylorthosilicate was used as a precursor and during a condensation reaction, an inorganic silica layer was formed. Then, 3-methacryloxypropyltrimethoxysilane was attached on the surface and in situ polymerization of acrylic acid (AA), as a hydrophile monomer, was performed. The obtained Al/Si/PAA flakes were characterized by different methods such as Fourier transform infrared spectroscopy, energy-dispersive X-ray spectroscopy, scanning electron microscopy, and transmission electron microscopy (TEM). The attached PAA chains on the surface were deattached by HF aqueous solution and analyzed by gel permeation chromatography. Also, the surface energy of samples was measured using Owens and Wendt equation by means of contact angle data. As results, the characterizing tests approved the successful encapsulation of Al pigments and TEM image showed a 10–15 nm silica layer and a 20–25 nm PAA layer. Although the Al/Si pigments showed a quantity of evolved hydrogen, the hybrid coated pigments had excellent anticorrosive properties in acidic and alkaline solutions. Also, the surface free energy of Al/Si/PAA showed an increase compared to that of Al.     

Biomimetic approach for the synthesis of N,N’-diarylsubstituted formamidines catalyzed byβ-cyclodextrin in water

An environmentally benign and highly efficient biomimetic approach for the synthesis of N,N′-diarylsubstituted formamidines in water catalyzedβ-cyclodextrin is described under neutral condition with quantitative yields of products.β-Cyclodextrin has been recovered and reused.     

Electrode grafting by oxidation of an amine catalyzed by a ferrocenyl “antenna” through intramolecular electron transfer

Two aminoferrocene complexes were studied by electrochemical techniques. Molecules retain the redox properties of both ferrocene and amine groups, but fundamentally different behaviours were observed depending on whether the linker between the two redox end groups was saturated (ethyl bridge) or not (ethynyl bridge). The possibility of an intramolecular electron transfer from the amine to the ferricenium moiety through the π-conjugated linker was demonstrated and the ethynyl bridge is expected to have a dual effect by facilitating both the oxidation of the amine into the cation radical and the production of aminyl radical, due to its strong electron withdrawing effect. Because of this synergy of properties, grafting of the conjugated aminoferrocene complex can occur just by oxidizing the ferrocene group without the presence of a base in solution.     

In situ carbon nanotube synthesis by the reduction of NiO/γ-Al2O3 catalyst in methane

The synthesis of carbon nanotubes (CNTs) via chemical vapour deposition of methane on NiO/γ-Al2O3 catalyst has been investigated. The reduction behavior of NiO/γ-Al2O3 by methane was studied using thermogravimetric (TG) and X-ray diffraction (XRD) techniques. It was found that the NiO supported on γ-Al2O3, was reduced to Ni⁰ in methane atmosphere in the temperature range of 710--770 ℃. The catalytic activity of NiO/γ-Al2O3 for CNTs synthesis by in situ chemical vapour deposition of methane during the reduction was also investigated. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to observe the CNTs produced at various reduction temperatures. The results indicated that the reduction temperature exhibits obvious influence on the morphology and the yield of CNTs. CNTs with the diameter of about 20 nm were obtained at reduction temperature of 750 ℃, and higher reduction temperature (such as 800 and 850 ℃) led to an increase in CNTs diameter and a decrease in CNTs yield.     

In situ carbon nanotube synthesis by the reduction of NiO/γ-Al_2O_3 catalyst in methane

The synthesis of carbon nanotubes (CNTs) via chemical vapour deposition of methane on NiO/γ-Al2O3 catalyst has been investigated.The reduction behavior of NiO/γ-Al2O3 by methane was studied using thermogravimetric (TG) and X-ray diffraction (XRD) techniques.It was found that the NiO supported on γ-Al2O3,was reduced to Ni0 in methane atmosphere in the temperature range of 710-770℃.The catalytic activity of NiO/γ-Al2O3 for CNTs synthesis by in situ chemical vapour deposition of methane during the reduction was also investigated.Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to observe the CNTs produced at various reduction temperatures.The results indicated that the reduction temperature exhibits obvious influence on the morphology and the yield of CNTs.CNTs with the diameter of about 20 nm were obtained at reduction temperature of 750℃,and higher reduction temperature (such as 800 and 850℃) led to an increase in CNTs diameter and a decrease in CNTs yield.