Fabrication and characterization of NiTiO3 nanofibers by sol–gel assisted electrospinning

Continuous NiTiO₃ nanofibers have been successfully synthesized by a sol–gel assisted electrospinning method followed by calcination at 600 °C in air. These nanofibers were characterized for the morphological, structural and optical properties by scanning electron microscopy (SEM), energy-dispersive X-ray spectrum (EDS), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectra (XPS) and UV–visible (UV–vis) diffuse reflectance spectroscopy (DRS). SEM results reveal that the obtained NiTiO₃ nanofibers are 175 nm in diameter and several micrometers in length after annealing at 600 °C. The XRD analysis shows that the nanofibers possess highly crystalline structure with no impurity phase. In contrast, the NiTiO₃ nanoparticles synthesized at the identical conditions by a sol–gel route have impurities including TiO₂ and NiO. Moreover, the electrospun NiTiO₃ nanofibers are endowed with an obvious optical absorbance in the visible range, demonstrating they have visible light photoresponse.     

Preparation and characterization of nanocrystalline Ca-doped CeO2 by sol–gel process

The reactivity of CeO₂ is determined by grain size and oxygen vacancies, which can be achieved by doping elements with less oxidation state into CeO₂. In this study nanocrystalline Ca-doped CeO₂ sol was synthesized from the reaction of hydrate cerium (III) nitrate and calcium nitrate tetrahydrate in alcohol solution after being calcined at 600?°C. X-ray diffraction as well as selected area electron diffraction gave evidence that the synthesized Ca-doped CeO₂ samples were well crystalline and had a cubic fluorite structure. TEM observation revealed that Ca-doped CeO₂ was composed by nanoparticles with grain size around 8?nm. The Raman spectrum of pure CeO₂ consists of a single triple degenerate F_2g model characteristic of the fluorite-like structure. In the Ca-doped CeO₂ sample, two additional low-intensity Raman bands were detected, thus confirming the formation of the solid solution. The synthesized nanometric powder is expected to be used in solid oxide fuel cells as well as in the catalytic treatment of automobile exhaust fumes.     

Preparation and characterization of boron-based bioglass by sol−gel process

45S5 bioglass has been widely studied in the last few decades because of its bioactivity and promising applications in the biomedical field. Boron, even few studied, represents a potential element to improve the properties of the 45S5 bioglass derivatives. The bioglasses are conventionally prepared by heat treatment of oxides and silicon. Here, the sol?gel method is proposed for the preparation of the boron-based 45S5 bioglass (45S5B) and the classical 45S5 bioglass (45S5), using water-soluble salts as raw materials. The bioglasses were characterized by FTIR, XRD, and SEM, indicating the success of the sol?gel method for preparation of the samples. The bioglasses were also tested in vitro for bioactivity in biological conditions and cytotoxicity against eukaryotic cells. The bioactivity of 45S5B was similar to the bioactivity of 45S5 bioglass, indicated by the deposition of hydroxyapatite crystals at the surface of the pristine bioglasses. The results of cytotoxicity tests revealed that the IC₅₀ of 45S5B (IC₅₀?=?7.56?mg?mL^?1) was similar to the IC₅₀ of 45S5 (IC₅₀?=?8.15?mg?mL^?1), indicating its safety for application in the biomedical field.

Open image in new window

     

Fabrication and photocatalytic activities of SrTiO3 nanofibers by sol–gel assisted electrospinning

SrTiO₃ nanofibers were successfully prepared by a facile electrospinning method with subsequent calcination in air. These one dimensional nanostructures were characterized for the morphological, structural and optical properties by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and UV–visible diffuse reflectance spectroscopy. The photocatalytic investigations showed that the SrTiO₃ nanofibers possessed enhanced photocatalytic efficiency in photodegradation of rhodamine B and photocatalytic H₂ evolution from water splitting under ultraviolet light irradiation, compared with the SrTiO₃ nanoparticles and P25. The enhanced photocatalytic performance can be ascribed to the beneficial microstructure and more negative conduction band edge compared with P25.     

Preparation and characterization of CaCu3Ti4O12 powders by non-hydrolytic sol–gel method

CaCu₃Ti₄O₁₂ (CCTO) powders were prepared via a non-hydrolytic sol–gel (NHSG) method by using acetylacetone as chelating agent and ethylene glycol as solvent. The samples were characterized by TG–DSC, Fourier transform infrared spectroscopy, X-ray diffraction and scanning electron microscope. The dielectric properties of ceramics were also measured. The pure perovskite-like CCTO powders were obtained by heat treatment at 800 °C for 2 h. The average particle sizes of CCTO powders calcined at 800 °C were approximately 350–450 nm. The samples sintered at 1,000 °C showed the mean grain size of 2.5–4 μm. Specially, the ceramics exhibited high dielectric constant (1.19 × 10⁵–1.40 × 10⁵) and low dielectric loss (0.051–0.1) in the temperature range of 30–110 °C. Moreover, with the NHSG method the period of synthesis process was greatly shortened.     

Synthesis and characterization of silica xerogels obtained via fast sol–gel process

The synthesis and physical properties of high surface area silica xerogels obtained by a two-step sol–gel process in the absence of supercritical conditions are reported. The hydrolysis and condensation reactions were followed by infrared spectroscopy. The increment in the bands corresponding to silanol and hydroxyl groups suggests that the hydrolysis reaction was complete during the first 30 min. The effect on surface area and global reaction time under various reaction conditions, such as type of alkaline catalyst and solvents, water–monomer and solvent–monomer molar ratios, was also studied. The obtained results suggest that surface area was increased using 3-aminopropyltriethoxysilane as catalyst. The use of isopropyl alcohol as solvent promotes the reduction of the capillary stress, giving a well-structured xerogel. As a conclusion, with H₂O/i-PrOH/TEOS in a molar ratio of 10:4:1, it was possible to obtain silica xerogels with surface areas about 1,240 m²/g. Such surface areas are comparable with those obtained under supercritical conditions (aerogels), and higher than those xerogels conventionally obtained under normal condition (500–800 m²/g).     

Fabrication of hierarchically porous silica nanospheres through sol–gel process and pseudomorphic transformation

Hierarchically porous silica nanospheres with well-defined morphology and uniform particle size had been synthesized through a multistep sol–gel method combined with pseudomorphic transformation in the presence of polyvinylpyrrolidone (PVP) and cetyltrimethylammoium bromide (CTAB) as dual template. The prepared materials were characterized by small-angle X-ray diffraction, transmission electron microscopy, scanning electron microscopy, and nitrogen physical adsorption techniques. The preparation process and the origin of hierarchical structure were also investigated. It had been shown that the hierarchical structure of synthesized materials comprises wormlike framework mesopores with diameters of about 3 nm and bubble-like pores with diameters of 20–30 nm. CTAB and PVP behave as dual-template and are responsible for the formation of the mesopores and big pores, respectively. Not only the porous structure, but also the morphology and particle size of hierarchical materials can be adjusted by controlling the addition of PVP. In addition, the formation process of hierarchically porous silica was investigated by transmission electron microscopy, FT-IR spectra and thermo-gravimetric curves and a possible synthetic mechanism had been proposed.     

Formation and characterization of phosphate-modified silicate materials derived from sol–gel process

Phosphate-containing silicate materials prepared using sol–gel method from Si(OC₂H₅) were investigated at the variation of the amount of phosphate modifier from 5 to 50 wt% in term of P₂O₅. Chemical composition, textural and structural properties of these materials were characterized by FTIR-spectroscopy, TEM, X-ray diffraction and nitrogen adsorption. It was shown that the materials posse monomodal pore size distribution of 5–20 nm for the samples dried at 100 °C and 40–60 nm for the specimens calcined at 600 °C. The mean pore size and surface area depended on the amount of phosphoric acid. Before the stage of high temperature treatment phosphoric acid, introduced into the structure of the materials as a modifying agent, was uniformly distributed inside a porous space of the material and was not chemically bonded with silicate. After high temperature treatment both chemical interaction of silicate with phosphate, providing the formation of silicate-phosphate structures, as well as redistribution of free modifier from the bulk of granules to their surface took place. The polyphosphate layer is formed on the material surface closing the internal porous space. However, in this case a part of the phosphate modifier remains chemically unbound to SiO₂ structure.     

Fabrication and properties of xBiFeO3-(1 − x)Bi4Ti3O12 system by sol–gel process

The thin films of mixture of xBiFeO₃-(1 − x)Bi₄Ti₃O₁₂ (x = 0.4, 0.5, and 0.6) system were prepared by a sol–gel process. The thicknesses of the thin films were 540, 500, and 570 nm, respectively. The crystal structure of all thin films annealed at 650 °C was analyzed by X-ray diffraction. It was found that the thin films at x = 0.4 and 0.5 mainly consisted of a Bi₄Ti₃O₁₂ phase while Bi₅Ti₃FeO₁₅ was the major phase of the thin film at x = 0.6. The thin film (x = 0.6) showed better ferroelectric properties in remnant polarization and polarization fatigue than those observed in the thin films (x = 0.4 and 0.5). The values of remnant polarization 2P _r and coercive field 2E c of the thin film at x = 0.6 were 36 μC/cm² and 192 kV/cm at an applied electric field of 260 kV/cm, respectively. There was almost no polarization fatigue up to 10¹⁰ switching cycles. Also weak ferromagnetism was observed in the thin film at x = 0.6.     

Synthesis and characterization of nitrogen-doped TiO2 nanoparticles prepared by sol–gel method

The N-doped TiO₂ has been synthesized by sol?Cgel method, using titanium isopropoxide, isopropanol and an aqueous solution of ammonia with ratio 2:1:10. The concentrations used for the NH₃ aqueous solution were 3, 7, 10 and 15?%. The samples have been analysed by X-ray diffraction, electron microscopy (SEM and TEM) thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), micro-Raman spectroscopy and diffuse reflectivity. TEM, SEM, DSC and TGA showed that the morphology is influenced by the presence of N^3? ions but not by the concentration of the solution. Instead reflectance gave us a relation between values of the energy gap and the concentration of N^3? ions: the gap between valence and conduction band lowers as the concentration of NH₃ in the starting solution increases. From these results we can say that the properties of the material have been tuned by doping with nitrogen ions because the particles absorb more light in the visible range, and this is important for photovoltaic and photocatalytic applications.     

Synthesis and characterization of lead oxide nano-powders by sol–gel method

Our goal in this research was to obtain lead oxide nano-powders by sol–gel method. In this method, lead oxide nano-powders were synthesized through the reaction of citric acid (C₆H₇O₈·H₂O) solution and lead acetate [Pb(C₂H₃O₂)₂] solution as stabilizer and precursor, respectively. The effect of different parameters including calcination temperature, (molar ratio of citric acid to lead acetate) and drying conditions were investigated. The prepared lead oxide nano-powders were characterized by FT-IR spectroscopy, X-ray diffraction, thermogravimetric analysis and scanning electron microscopy. The prepared PbO samples consist of the particles in the range of 50–120 nm or the thick plate like structures with thickness of 53 nm depending on the drying conditions.     

Synthesis and characterization of nanostructured aluminum borate by sol–gel method

Nanostructured aluminum borate was synthesized using sol?Cgel technique. X-ray diffraction study revealed that the synthesized aluminum borate was single crystal. These nanorods have very uniform diameter. High-resolution transmission electron microscope images indicate that aluminum borate is well crystallized. The alternating current (AC) conductivity of the aluminum borate was studied as a function of temperature and frequency. The AC conductivity mechanism of the aluminum borate was found to be proportional to ??^s. The exponent s is almost independent with temperature. This suggests that AC conductivity mechanism of the aluminum borate can be interpreted by localized hopping model.     

Synthesis and characterization of nanocrystalline tin oxide by sol–gel method

Nanocrystalline SnO₂ particles have been synthesized by a sol–gel method from the very simple starting material granulated tin. The synthesis leads a sol–gel process when citric acid is introduced in the solution obtained by dissolving granulated tin in HNO₃. Citric acid has a great effect on stabilizing the precursor solution, and slows down the hydrolysis and condensation processes. The obtained SnO₂ particles range from 2.8 to 5.1 nm in size and 289–143 m² g⁻¹ in specific surface area when the gel is heat treated at different temperatures. The particles show a lattice expansion with the reduction in particle size. With the absence of citric acid, the precursor hydrolyzes and condenses in an uncontrollable manner and the obtained SnO₂ nanocrystallites are comparatively larger in size and broader in size distribution. The nanocrystallites have been characterized by means of TG-DSC, FT-IR, XRD, BET and TEM.     

Preparation and characterization of In2O3/ZnO heterostructured microbelts by sol–gel combined with electrospinning method

Long and thin In₂O₃/ZnO heterostructured microbelts were synthesized by sol–gel combined with electrospinning process. The as-prepared microbelts show the well defined one-dimensional belt structures with 1–5 μm in width and tens of millimeters in length. The polycrystalline microbelts calcined at 973 K for 1 h are still continuous and have the uniform rectangular cross sections and the thickness to width ratio is around 1:10. The crystalline phases of samples are investigated by X-ray diffraction and the morphology is examined using transmission electron microscope and scanning electron microscope. In₂O₃/ZnO heterostructured microbelts exhibit the excellent visible photocatalytic property in the photodegradation of methyl orange (MO), and over 94 % of MO was degraded within 3 h.     

Preparation and characterization of magnetic TiO2/ZnFe2O4 photocatalysts by a sol–gel method

A magnetic TiO₂/ZnFe₂O₄ photocatalyst was prepared by a sol-gel method, and X-ray diffraction (XRD), magnetic and photocatalytic properties analysis were employed to characterize this photocatalyst. The XRD results show that ZnFe₂O₄ can prevent the transformation of titania from anatase to rutile. The magnetic properties analysis indicates that TiO₂/ZnFe₂O₄ is of large saturation magnetization value and low coercivity. The photocatalytic experimental results show that TiO₂/ZnFe₂O₄=3 and 4 are superior in photocatalytic reactivity to other proportions. TEM shows that TiO₂/ZnFe₂O₄ has a fine core-shell fabric. After being used for four times during the photocatalytic reaction, the TiO₂/ZnFe₂O₄ nanoparticles have good photocatalytic stability.     

Synthesis and characterization of sol–gel alumina nanofibers

Abstract Alumina nanofibers of high aspect ratio with surface area of >300 m² g⁻¹ has been prepared successfully in bulk quantities by the sol–gel method. The synthesis parameters including the binary water–alcohol solvent system to aluminium isopropoxide ratio, pH, type of solvent and aging temperature affect the uniformity and formation of nanofibers. It is proposed that alumina nanofibers were formed by the curling of the nanosheets upon condensation after the hydrolysis. The phase evolution of alumina nanofibers from pseudoboehmite to α phase has been shown by XRD and FTIR. ²⁷Al NMR investigations show that the Al atoms are six and four coordinated. The morphology of the alumina nanofibers does not change much as the calcination temperature was increased. In addition, the average pore size increases and the BET surface area decreases as a function of calcination temperature. The thermal behavior of alumina nanofibers was investigated by TGA. Graphical Abstract