碘化钾碘蓝分光光度法测定微量过氧化氢

基于在酸性介质中 ,过氧化氢与碘化钾、淀粉的显色反应 ,建立了碘化钾碘兰分光光度法测定微量过氧化氢方法。过氧化氢浓度在 0～ 2 5μg/2 5m L范围内有良好的线性关系 ,方法的相对标准偏差 1 .2 % ,回收率 97.2 %～1 0 1 .2 % ,检出限为 2 .0× 1 0 -3 mg/L。并应用于雨水、空气中微量过氧化氢的测定。     

连续流动注射法测定土壤和植物中全磷

应用AA3型连续流动分析仪测定了土壤和植物中全磷.结果表明:对于采用高氯酸-硫酸消解的土壤样品以及硫酸-过氧化氢消解的植物样品,在测定时调节反应混合液的酸度使其在显色的适宜范围内,磷的质量浓度在6 mg·L-1(土壤)和7.5 mg·L-1(植物)以内呈线性,相关系数分别为0.999 2(土壤)和0.999 6(植物);加标回收率98.5%～100.5%,相对标准偏差小于2%,检出限分别为0.010 mg·L-1(土壤)和0.013 mg·L-1(植物).     

2-(2-喹啉偶氮)-1,5-二氨基苯固相萃取光度法测定痕量钯

根据2-(2-喹啉偶氮)-1,5-二氨基苯(QADAB)与钯的显色反应及MCI-GEL反相固相萃取小柱对显色络合物的固相萃取,建立了一种测定痕量钯的方法.在0.2～3.0 mol·L-1高氯酸介质中,溴化十六烷基三甲胺(CTMAB)存在下,QADAB与钯反应生成2:1稳定络合物,该络合物可被MCI-GEL反相固相萃取小柱萃取富集,富集的络合物用丙酮洗脱后用光度法测定,在丙酮介质中体系的最大吸收波长为600 nm,表观摩尔吸光率为9.63×104L·mol-1·cm-1.钯质量浓度在0.01～L 5 mg·L-1内符合比耳定律,方法用于几种实样中痕量钯的测定,测得回收率在86%～96%间.     

阴离子树脂苯取富集-分光光度法测定煤矸石中痕量钪

研究了对乙酰基偶氮氯膦(CPApA)与钪(Ⅲ)的显色反应,在HNO3介质中,在Triton X-100存在下,CPApA与钪(Ⅲ)反应生成摩尔比为1:1的稳定配合物,该配合物可用717型阴离子树脂交换柱萃取富集,再通过树脂相光度法测定钪,由此建立了测定钪的新方法.吸附配合物树脂相的最大吸收波长为690 nm,表观摩尔吸光系数为9.56×105 L·mol-1·cm-1.钪的质量浓度在0～480μg/L范围内符合比耳定律.经阴离子树脂交换柱萃取富集后,钪的测定灵敏度可提高数倍,大多数常见离子不干扰测定.方法应用于煤矸石痕量钪的测定,结果满意.样品分析结果的相对标准偏差小于5%,加标回收率为96.0%～102.5%.     

4-(5-氯-2-吡啶)-偶氮-1,3-二氨基苯显色光度法测定钯(Ⅱ)

研究了4-(5-氯-2-吡啶)-偶氮-1,3-二氨基苯(5-Cl-PADAB)与Pd的显色反应,在0.48 mol/L H3PO4介质和100℃水浴条件下,5-Cl-PADAB与Pd(Ⅱ)反应生成2:1稳定络合物,其最大吸收波长为570nm,表观摩尔吸光系数为6.39×104 L.mol-1.cm-1。结果表明:Pd含量在0～1.2 mg/L内符合比尔定律,方法已用于矿样中微量Pd的测定,结果与AAS法相符。样品分析结果的相对标准偏差小于4%,加标回收率为98.5%～103.0%。     

磷钼钨三元杂多酸光度法测定药物中的抗坏血酸

研究了抗坏血酸与磷钼钨三元杂多酸的显色反应,提出了借磷钼钨杂多蓝测定抗坏血酸的分光光度法.最大吸收波长为730nm,抗坏血酸在0.08～10mg/L范围内线性良好.回归方程为A=1.05×10⁴C+0.017,线性相关系数γ=0.9995,表观摩尔吸光系数ξ₇₃₀=1.05×10⁴L·mol^-1·cm^-1,方法检出限为0.04mg/L,回收率为94～102%,相对标准偏差≤1.5%(n=8).本方法由于钨钼的混合配位增强了氧化能力,较之二元杂多酸的方法,省去了水浴加热等操作,只需在室温下反应30min,吸光值至少可稳定6h.过量的黄色杂多酸可加入适量的氢氧化钠溶液分解,从而获得色泽纯正的高灵敏度显色体系.     

曙红Y探针吸收光谱法测定氯霉素

在pH 1.0～3.0的条件下,曙红Y与氯霉素反应生成红色离子缔合物,其最大显色波长和褪色波长分别位于483 nm和560 nm,表观摩尔吸光系数分别为4.49×104和1.20×104L·mol-1.cm-1,当用双波长叠加法测定时,表观摩尔吸光系数可提高到5.70×104L·mol-1.cm-1,在0.15～6.5 mg.L-1范围内,显色反应或褪色反应的吸光度绝对值与溶液中氯霉素浓度成正比,由此建立了测定氯霉素的吸收光谱法。该法用于药物及尿样中氯霉素的测定,结果满意。     

Au-TMK-TritonX-100全差示分光光度法测定痕量金

已报导测定痕量金的比色法均为目视比色测定。本文研究了TMK-Triton X-100与金显色反应的条件和性质,结果表明,显色反应的最佳酸度为pH2.5—4.3,最大吸收波长约在555nm,表观吸光系数为1.43×10~5L.mol~(-1).cm~(-1)、络合物能稳     

新型显色剂均三溴偶氮甲磺光度法测定微量铅

研究了显色剂均三溴偶氮甲磺与铅的显色反应.在1.92 mol.L-1磷酸介质中,铅与试剂有很灵敏的显色反应,形成1∶2的蓝色配合物,最大吸收波长为642 nm,铅量在0~25μg/25 mL范围内符合比耳定律,摩尔吸光系数为9.3×104L.mol-1.cm-1。除锶、钡和稀土元素外,其它元素无明显干扰,方法可直接应用于铝合金中铅的测定,结果与标准值相符,RSD小于2%。     

阴离子树脂萃取富集-分光光度法测定煤矸石中痕量钪

研究了对乙酰基偶氮氯膦(CPApA)与钪(Ⅲ)的显色反应,在HNO3介质中,在TritonX-100存在下,CPApA与钪(Ⅲ)反应生成摩尔比为1:1的稳定配合物,该配合物可用717型阴离子树脂交换柱萃取富集,再通过树脂相光度法测定钪,由此建立了测定钪的新方法。吸附配合物树脂相的最大吸收波长为690nm,表观摩尔吸光系数为9.56×105L.mol-1.cm-1。钪的质量浓度在0～480μg/L范围内符合比耳定律。经阴离子树脂交换柱萃取富集后,钪的测定灵敏度可提高数倍,大多数常见离子不干扰测定。方法应用于煤矸石痕量钪的测定,结果满意。样品分析结果的相对标准偏差小于5%,加标回收率为96.0%～102.5%。     

Determination of formaldehyde in foodstuffs by flow injection spectrophotometry using phloroglucinol as chromogenic agent

A spectrophotometric method for the determination of formaldehyde in foodstuffs was described by using phloroglucinol as the chromogenic agent. The reaction between formaldehyde and phloroglucinol could occur rapidly at room temperature under mild conditions. The spectrophotometric measurements were conducted at 474nm of an unstable intermediate orange product of the reaction, which greatly increased the sample throughput. Flow injection technique was used to control the merging and reaction timing of the reagents and sample. A detection limit (3sigma) of 0.023microg ml(-1) was achieved. The relative standard deviation was 0.29% for the determination of 7microg ml(-1) formaldehyde (n=11). The proposed method was applied to the analyses of formaldehyde in several preserved foodstuffs and the results were in good agreement with those obtained by a standard method.     

Sequential injection analysis for Cr(VI) and Cr(III) with renewable surface reflection spectrophotometry.

On the basis of the chromogenic reaction of chromium(VI) with 1,5-diphenylcarbohydrazide (DPC) on the surface of Polysorb C-18 beads and the sequential injection renewable surface technique (SI-RST), a highly sensitive reflect spectrophotometric method for the determination of chromium(III) and chromium(VI) was proposed. Considerations of system and flow cell design, and factors that influence the determination performance were discussed. With 300 microl of sample loaded and 0.6 mg of beads trapped, the linear response range was 0.02 - 0.5 mg l(-1) Cr(VI) with a detection limit (3 sigma) of 2.4 microg l(-1) Cr(VI). The method achieves a precision of 1.3% RSD (n = 11) and a throughput of 53 samples per hour. The determination of Cr(III) was based on the same reaction for the determination of Cr(VI) after being oxidized by (NH4)2S2O8. The precision of the oxidation method was evaluated using a 0.2 mg l(-1) Cr(III) standard, yielding an RSD of 2.5% (n = 11). The average recovery of Cr(III) oxidized was tested to be 99.1%. The proposed method was used in the simultaneous determination of Cr(VI) and Cr(III) in water samples, and the error was less than 3%.     

Indirect spectrophotometric determination of ascorbic acid with ferrozine by flow-injection analysis

A FIA indirect spectrophotometric determination of ascorbic acid was developed using its reducing action on Fe(III) in acidic medium and following the spectrophotometric determination of the reduced iron by using sodium 3-(2-pyridyl)-5,6-diphenyl-1,2,4-triazine-4',4'-disulphonate (ferrozine) as chromogenic reagent in buffered medium (pH 5.5) and monitoring the absorbance signal at 562 nm. A three-line manifold with two reaction coils was used: in the first reaction coil, ascorbic acid reduces Fe(III) to Fe(II); and in the second one, the complexation reaction is developed. The linear range of the method was 0.5-10 mug ml(-1) of ascorbic acid, the detection limit being 0.028 mug ml(-1). The proposed method was sensitive, rapid (sampling rate of 90 samples h(-1)) and reproducible (RSD 0.19%, n=10). Satisfactory results were obtained in the determination of ascorbic acid in pharmaceutical preparations, fruit juices and urine testifying the applicability of the method to real samples.     

紫外分光光度法测定聚硫密封胶中二氧化钛

基于强酸性溶液中钛氧离子与H2O2发生显色络合反应的原理,建立了浓硫酸–硫酸铵消解–紫外分光光度法测定聚硫密封胶中TiO_2含量的方法。通过对酸液和显色剂用量,以及显色络合物稳定性的系统考察,确定浓硫酸用量为2 mL,双氧水用量为3 mL,检测波长为403 nm。二氧化钛质量浓度在0~130μg/mL范围内与其吸光度呈良好的线性关系,线性方程为A=5.047 8c–0.019 31,r~2=0.999 2,检出限为0.08μg/mL。检测结果的相对标准偏差为0.89%(n=5),3水平加标平均回收率为101.7%。该方法线性范围较宽、检出限低、重复性好,可用于聚硫密封胶中二氧化钛的定量分析。     

Spectrophotometric determination of silver with 2-(2-quinolylazo)-5-diethylaminophenol as chromogenic reagent

A new chromogenic reagent, 2-(2-quinolylazo)-5-diethylaminophenol (QADEAP) was synthesized. A highly sensitive, selective and rapid method for the determination of silver based on the rapid reaction of silver(I) with QADEAP has been developed. In the presence of citric acid-sodium hydroxide buffer solution (pH=5.0) and sodium dodecyl sulfonate (SDS) medium, QADEAP reacts with silver to form a violet complex of a molar ratio 1:2 (silver to QADEAP). The molar absorptivity of the complex is 1.33x10(5) L mol(-1) cm(-1)at 590 nm. Beer' s law is obeyed in the range of 0.01-0.6 micro g mL(-1). The relative standard deviations for eleven replicate samples of 0.2 microg mL(-1) is 1.38%. This method was applied to the determination of silver in water with satisfactory results.     

Capillary electrophoresis and circular dichroism study of trichosanthin and its mutants

A new chromogenic reagent, 2-(2-quinolylazo)-5-diethylaminoaniline (QADEAA) was synthesized. A highly sensitive, selective and rapid method for the determination of silver based on the rapid reaction of silver (I) with QADEAA has been developed. In the presence of sodium citrate-sodium hydroxide buffer solution (pH 6.5) and sodium dodecyl sulfonate (SDS) medium, QADEAA reacts with silver to form a violet complex of molar ratio 1:2 (silver to QADEAA). The molar absorptivity of the complex is 1.39x10(5) l mol(-1) cm(-1) at 580 nm. Beer's law is obeyed in the range of 0.01-0.6 mug ml(-1). The relative standard deviation for 11 replicate samples of 0.2 mug ml(-1) is 1.67%. This method can be applied to the determination of silver in water with satisfactory results.     

粉煤灰中痕量汞的催化光度法测定

在 p H3.5乙酸 -乙酸钠缓冲溶液中痕量汞 ( )对 K4[Fe( CN) 6 ]与 4 ,7-二苯基 -1 ,1 0 -邻菲 口罗啉 ( BPT)显色反应有催化作用 ,加入硫脲能提高其灵敏度 ,显色程度与 Hg( )量在一定范围内呈线性相关。借此建立测定痕量 Hg( )的分光光度法。实验表明 ,有色溶液的最大吸收波长为 535nm,摩尔吸光系数为 4 .5× 1 0 6 L·mol- 1· cm- 1 ,催化程度与 Hg( )量在 0 .0～ 2 .0 μg/ 50 m L范围内符合比耳定律 ,选择性较好。结合萃取分离 ,本法可用于测定粉煤灰中的痕量汞。     

Spectrophotometric determination of aminomethylbenzoic acid using sodium 1,2-naphthoquinone-4-sulfonate as the chemical derivative chromogenic reagent

A new method has been established for the determination of aminomethylbenzoic acid using sodium 1,2-naphthoquinone-4-sulfonate as the chemical derivative chromogenic reagent. This method is based on the formation of a pink compound from the reaction of aminomethylbenzoic acid and sodium 1,2-naphthoquinone-4-sulfonate. The nucleophilic substitution reaction proceeds quantitatively in pH 12.0 buffer solution. The stoichiometric ratio of the reaction, maximum absorption wavelength and the value of epsilon(430) were 1:1, 430 nm, and 2.87 x 10(3)L mol(-1)cm(-1), respectively. Beer's law was obeyed in the range of 0.80-80 mg/L of aminomethylbenzoic acid. The data have been filled to a linear regression equation A=0.03183+0.01658C (mg/L), with a correlation coefficient of 0.9996. The detection limit is 0.11 mg/L, R.S.D. is 0.54%, and average recovery is over 99.6%. This paper further improves the determination of aminomethylbenzoic acid compared to the previous methods. The kinetic property and reaction mechanism have also been discussed. This proposed method has been successfully applied to the determination of aminomethylbenzoic acid in injection of aminomethylbenzoic acid with satisfactory results.     

微波消解–分光光度法测定陶瓷原料中二氧化钛

采用微波消解–二安替比林甲烷分光光度法测定陶瓷原料中二氧化钛的含量。探讨了样品消解用酸的种类、检测波长、显色时间和显色剂用量对测定结果的影响。试验结果表明,以HNO_3–HF–H_2O_2溶解样品,395 nm为检测波长,显色20 min,显色液用量为12 m L时测试结果满意。测定钛的线性范围为0~2.0μg/m L,线性相关系数r~2=0.999 5,方法检出限为0.56μg/g。用该法对4种标准物质进行分析验证,测定结果与推荐值相符,测定结果的相对标准偏差为0.64%~2.28%(n=6),加标回收率为95.3%~104%。用该方法和国标方法对乐山和眉山地区陶瓷原料样品进行分析比对,经t检验证明,两种方法测定结果无显著性差异。该方法快速、准确,适合陶瓷原料中二氧化钛的检测。     

Study of 2-(2-quinolinylazo)-5-dimethylaminobenzoic acid as a new chromogenic reagent for the spectrophotometric determination of cobalt

2-(2-Quinolinylazo)-5-dimethylaminobenzoic acid (QADMAB) is proposed as a new sensitive and selective chromogenic reagent for spectrophotometric determination of cobalt. The QADMAB reacts with cobalt in the presence of cetyl trimethylammonium bromide (CTMAB) medium to form a violet complex of molar ratio 1:2 (cobalt to QADMAB) in the pH range 3.2-5.2. The molar absorptivity of the complex is 1.28x10(5) L mol(-1) cm(-1) at 625 nm. Beer's law is obeyed in range 0.01-0.32 micro g mL(-1). The relative standard deviation for eleven replicate samples of 0.2 micro g mL(-1) is 0.76%. This method was applied to the determination of cobalt in biological samples, Vitamin B(12), alloys and water with good results.