Ce:Lu2Si2O7闪烁晶体的结构和光谱特性

采用中频感应提拉法生长出Ce:Lu2Si2O7(Ce:LPS)晶体.通过x射线粉末衍射分析,晶体结构属单斜晶系的C2/m空间群.光学显微镜下可观测到晶体的(110)解理.在室温下测试了Ce:LPS晶体的吸收光谱、激发光谱和发射光谱.结果表明,Ce:LPS晶体的吸收峰只有两个,分别位于302和349 nm,且与激发峰的位置一致,归因于Ge3+的4f1→5d1跃迁的特征吸收所致.发射光谱具有Ce3+典型的双峰特征,经Gaussian多峰值拟合,带状谱是由384和407 nm两个发射峰叠加而成,且后者的强度明显高于前者.     

导模法生长Er:Lu2O3连续激光特性

导模法是一种超高熔点晶体的有效生长方法,可以生长高质量、大尺寸、高掺杂的Er:Lu₂O₃晶体。本文测试了导模法生长的Er:Lu₂O₃晶体的荧光发射谱及连续激光特性,在室温下获得了斜效率为23.1%的2.85μm连续激光输出,最高输出功率5.24 W。80 min功率RMS(Root mean square)稳定性优于1.4%,不同输出功率水平的激光光束质量M²因子优于2.17。实验结果表明,导模法生长的Er:Lu₂O₃激光晶体具备输出高功率、高效率中红外激光的能力。     

Lu2O3：Tb纳米粉末的光致发光特性

用燃烧合成法制备了Lu₂O₃:Tb³⁺纳米粉末。产物为立方相结构,粒径在3~40nm之间可控。对不同颗粒度的样品的激发光谱、发射光谱和荧光衰减特性进行了研究。在紫外光激发下,样品显示出较强的发光(来自于Tb³⁺的⁵D_3,4→⁷F_J跃迁)。同时,样品的光致发光性质在很大程度上受到样品颗粒度的影响,对此现象给出了合理的解释。     

Lu2SiO5∶Ce荧光粉的热释光特性研究

采用溶胶-凝胶(Sol-Gel)技术,分别在空气中和石墨提供的弱还原气氛下制备出Lu2SiO5∶Ce0.006荧光粉。通过分析样品的结构,光致激发、发射谱和热释光谱等特性,发现弱还原气氛下制备的样品不仅光致发光强度比空气中的强,而且热释光曲线中598K处的高温热释光峰也得到了抑制。进一步考察空气中制备的Lu2SiO5∶Ce0.006,Kx(x=0.01～0.08)荧光粉,结果表明就光致发光和热释光特性而言,K+共掺杂具有与还原气氛类似的作用。综合以上两方面分析结果,可认为598K处热释光峰是由与Ce4+相关的缺陷引起的,并对K+共掺杂LSO∶Ce发光增强的原因给出了合理解释。     

Lu2Si2O7∶Ce纳米晶的溶胶-凝胶法合成和闪烁性能

采用溶胶-凝胶法制备了Lu2Si2O7∶Ce纳米晶,利用X射线衍射(XRD)、扫描电镜(SEM)、荧光光谱仪、X射线激发发射谱仪对制备的Lu2Si2O7∶Ce纳米晶的晶相结构、微观形貌和光学性能进行了表征。结果表明,溶胶-凝胶法制备的Lu2Si2O7∶Ce前驱体在煅烧温度为1000℃时开始晶化,晶粒尺寸随着煅烧温度的升高而变大,1200℃煅烧2 h后的晶体颗粒均匀,分散性最优,平均晶粒尺寸约为28.9 nm,呈近球形;Lu2Si2O7∶Ce纳米晶的紫外吸收谱存在峰位分别为304 nm和350 nm两个吸收峰,源自于Ce^3+离子的4f→5d跃迁;光致发射谱和X射线激发发射谱都表现为典型的非对称双峰结构,归属于Ce^3+离子的5d^1→2F5/2和5d^1→2F7/2跃迁,Ce^3+离子的最佳掺杂浓度约为1%;荧光衰减时间约为37.2 ns,可满足高时间分辨X射线探测需要。     

Ca3NbGa3Si2O14晶体的介电和压电特性

利用Y切和(yxl)30°切两种样品测量了Ca3NbGa3Si2O14晶体的介电、压 电和部分弹性参数.计算了(yxl)θ切型相关压电常数随切角的变化.与La3Ga5SiO14晶体相比，Ca3NbGa3Si2O14晶体具有更优良的压电性能，其压电常数 d11=7.93×10-12C/N，d14=-5.88×10-12C/N. 关键词： Ca3NbGa3Si2O14晶体 介电常数 压电常数     

Ce3+/Eu2+共掺Ca3Si2O4N2荧光粉的光学特性

采用高温固相法制备了一种新型的白光LED用Ca3Si2O4N2∶Eu2+,Ce3+,K+荧光粉。利用X射线衍射仪对样品的物相结构进行了分析,结果表明:Ce3+和K+离子的掺杂没有改变Ca3Si2O4N2∶Eu2+荧光粉的主晶相。利用荧光光谱仪对样品的发光性能进行了测试,发现样品在355 nm激发下得到的发射光谱为峰值位于505 nm的单峰,是Eu2+离子5d-4f电子跃迁引起的。Ca3Si2O4N2∶Eu2+荧光粉通过Ce3+和K+离子的掺杂,发光明显增强。当Ce3+的摩尔分数为1%时,荧光粉的发光强度达到最大值,是单掺Eu2+离子荧光粉发光强度的168%。通过光谱重叠的方法计算Ce3+→Eu2+能量传递临界的距离为2.535 nm。     

硼酸对亚微米级Ca3Sc2Si3O12:Ce绿色荧光粉的制备及发光性能的影响

采用凝胶-燃烧法合成了Ca₃Sc₂Si₃O₁₂ ∶Ce绿色LED用荧光粉,用X射线粉末衍射(XRD)、扫描电镜(SEM)、荧光光谱仪等对合成产物进行了分析和表征.结果表明:通过添加H₃BO₃做助熔剂,制得的荧光粉晶相纯正,颗粒形貌均呈现为较规则的类球形,而且所得荧光粉的粒径均小于1 μm.发射光谱呈现为一宽带,发射主峰位于505 nm,该宽峰对应于Ce³⁺关键词： 白光LED 荧光粉 3Sc₂Si₃O₁₂ ∶Ce')" href="#">Ca₃Sc₂Si₃O₁₂ ∶Ce 发光     

Temperature-frequency dependence and mechanism of dielectric properties for γ-Y2Si2O7

This paper reports that single-phase γ-Y2Si2O7 is prepared via a sufficient blending and cold-pressed sintering technique from Y2O3 powder and SiO2 nanopowder. It studies the dielectric properties of γ-Y2Si2O7 as a function of the temperature and frequency. The γ-Y2Si2O7 exhibits low dielectric loss and non-Debye relaxation behaviour from 25 to 1400℃ in the range of 7.3-18 GHz. The mechanism for polarization relaxation of the as-prepared γ-Y2Si2O7 differing from that of SiO 2 is explained. Such particular dielectric properties could potentially make specific attraction for extensive practical applications.     

Li2B4O7晶体及其熔体结构的拉曼光谱研究

采用高温原位拉曼光谱技术,研究了Li₂B₄O₇从常温至1 373 K温度范围内的拉曼光谱。在升温过程中,晶体的拉曼光谱出现展宽和红移现象,且强度降低。晶体熔化时,由2个[BO₄]和2个[BO₃]组成的[B₄O₉]环状结构转变成(B₃O₆)3- 六元环和[BO₃]结构,[BO₄]结构减少直至消失。基于密度泛函理论,计算了Li₂B₄O₇晶体的拉曼光谱,对其振动模式进行了分析归属。利用量子化学从头计算法计算了由[B₃O₆-BO₃]为基础相互连接形成的x(Li₂B₄O₇)(x=2, 3, …, 9)的环状团簇模型的拉曼光谱,对Li₂B₄O₇熔体的结构进行了模拟分析。计算结果表明Li₂B₄O₇熔体的阴离子基元为三个(B₃O₆-BO₃)组成的大三元环超级结构。     

金属离子掺杂的Lu2Si2O7的第一性原理研究

焦硅酸镥掺铈(LPS:Ce)具有突出的闪烁性能, 比如高光产额和快衰减, 但晶格中的氧空位会影响其闪烁性能. 本文通过第一性原理方法研究了Li, Na, Mg和Ca在LPS中的稳定性和对氧空位的影响. 结果表明: 在缺氧环境下, 这些离子倾向于占据间隙位, 从而可能抑制氧空位. 分析了杂质离子对LPS电子结构的影响. 关键词： 第一性原理 焦硅酸镥 杂质缺陷     

Structural study of the Lu2Si2O7-Sc2Si2O7 system

Different compositions in the Lu₂Si₂O₇-Sc₂Si₂O₇ system have been synthesized following the ceramic method. All XRD patterns are compatible with the thortveitite structure (β-RE₂Si₂O₇ polymorph). Unit cell parameters change linearly with composition, which indicates a complete solid solubility of Sc₂Si₂O₇ in Lu₂Si₂O₇. ²⁹Si MAS NMR spectra show a decrease of the ²⁹Si chemical shift with increasing Sc content. A correlation reported in the literature to predict ²⁹Si chemical shifts in silicates is applied here to obtain the theoretical variation in ²⁹Si chemical shift values in the system Lu₂Si₂O₇-Sc₂Si₂O₇ and the results compare favourably with the values obtained experimentally. The FWHM values of the ²⁹Si MAS NMR curves indicate a random distribution of Lu and Sc in the structure of the intermediate members. Finally, the IR study of the system confirms the solubility of Sc₂Si₂O₇ in Lu₂Si₂O₇, showing the splitting of several modes in the intermediate members and a linear shift of the frequency on going from one end-member to the other.     

EPR study of Ce ions in lutetium silicate scintillators Lu2Si2O7 and Lu2SiO5

Two Ce³⁺-doped scintillator crystals, LSO (Lu₂SiO₅:Ce) and LPS (Lu₂Si₂O₇:Ce), are studied by EPR spectroscopy. The analysis indicates that Ce³⁺ substitutes for Lu³⁺ ion in a C₂-symmetry site for LPS and in two C₁-symmetry sites for LSO, with a preference for the largest one, with 6+1 oxygen neighbors. Angular dependence of the EPR spectrum shows that the electronic ground state of Ce³⁺ is different in these two matrices. It is mainly composed of |M_J|=5/2 state in LPS and |M_J|=3/2 state in LSO. The temperature dependence of the linewidth shows a noticeably long spin lattice relaxation time, especially in LPS, which is the result of a stronger crystal field in LPS than in LSO.     

Thermal expansion properties of Lu2-xFexMo3O12

The structures and thermal expansion properties of Lu2-xFexMo3O12 have been investigated by X-ray diffraction(XRD).XRD patterns at room temperature indicate that compounds Lu2-xFexMo3O12 with x≤1.3 exhibit an orthorhombic structure with space group Pnca;compounds with x=1.5 and 1.7 have a monoclinic structure with space group P21/a.Studies on thermal expansion properties show that the linear thermal expansion coefficients of orthorhombic phase vary from negative to positive with increasing Fe content.Attempts to make zero thermal expansion materials indicate that zero thermal expansion can be observed in Lu1.3Fe0.7Mo3O12 in the temperature range of 200-400℃.     

Dy^(3+)掺杂Lu_(2)O_(3)和Y_(2)O_(3)单晶光纤下转换荧光测温性能EI北大核心CSCD

稀土倍半氧化物单晶光纤材料凭借超高的熔点(~2400℃)、稳定的物化性能以及灵活的结构被认为是极具潜力的高温传感介质。本文采用激光加热基座(LHPG)法,成功生长了透明无开裂Dy^(3+)离子掺杂的倍半氧化物单晶光纤Lu_(2)O_(3)和Y_(2)O_(3)。依据Dy^(3+)离子的^(4)I_(15/2)和^(4)F_(9/2)能级为一对热耦合能级对(TCLs),测试得到了430~520 nm波长范围内的下转换荧光光谱。荧光强度比(FIR)结果显示,晶体在298~673 K温度范围内的荧光强度具有良好的温度相关性。其中Dy∶Lu_(2)O_(3)在该范围内的最大相对灵敏度和绝对灵敏度分别为0.97%·K^(-1)(315 K)和1.62×10^(-4) K^(-1)(673 K),展现出更为优异的温度传感性能。     

Synthesis of Y2Si2O7:Eu nanocrystal and its optical properties

Nanocrystalline Y₂Si₂O₇:Eu phosphor with an average size about 60 nm is easily prepared using silica aerogel as raw material under ultrasonic irradiation and annealing temperature at 300-600 °C and this nanocrystalline decomposes into Y₂O₃:Eu and silica by heat treatment at 700-900 °C. The excitation broad band centered at 283 and 254 nm results from Eu³⁺ substituting for Y³⁺ in Y₂Si₂O₇ and Y₂O₃/SiO₂, respectively. Compared with Y₂O₃:Eu/SiO₂ crystalline, the PL excitation and emission peaks of Y₂Si₂O₇:Eu nanocrystalline red-shift and lead to the enhance of its luminescence intensity due to the different chemical surroundings of Eu³⁺ in above nanocrystallines. The decrease of PL intensity may be ascribed to quenching effect resulting from more defects in Y₂O₃:Eu/SiO₂ crystalline.     

First-principles calculation of structural and electronic properties of pyrochlore Lu2Sn2O7

A Density functional theory method within generalized gradient approximation has been performed to obtain the static lattice parameters, oxygen positional parameter, bond length and bond angle and electronic properties of ideal Lu₂Sn₂O₇ pyrochlore. The results are in excellent agreement with available experimental measurements. Density of states (DOS) of this compound was presented and analysed. We also notice the presence of the hybridization between oxygen and Lu metal. The band structure calculations show that the compound has direct band gap of 2.67 eV at the Γ point in the Brillouin zone and this indicates that the material has a semi-conducting feature.     

New compounds Yb2Fe3O7 and Lu2Fe3O7

New compounds A₂Fe₃O₇ (A = Yb and Lu) were synthesized under low oxygen partial pressures at 1200°C, and their possible space group and lattice constants were determined.     

Thermoluminescence studies on Cu-doped Li2B4O7 single crystals

Lithium tetraborate (Li₂B₄O₇) is a tissue equivalent material and single crystals of this material doped with Cu are promising for dosimetric applications. In the present study highly transparent single crystals of lithium tetraborate (Li₂B₄O₇) doped with Cu (0.5 wt%) have been grown using the Czochralski technique. The Li₂B₄O₇:Cu crystals were studied using photoluminescence, X-ray diffraction (XRD), UV-vis transmission, time resolved fluorescence and thermoluminescence (TL) techniques. The TL readout of Li₂B₄O₇:Cu crystals showed two well-defined glow peaks at 402 K (peak-1) and 513 K (peak-2) for a 4 K/s heating rate. While the low temperature TL peak-1 fades completely within 24 h at room temperatures, the main dosimetric peak-2 remains the same. The TL sensitivity of the grown single crystal is found to be 3.3 times that of a conventional TL phosphor, TLD-100. The Li₂B₄O₇:Cu crystals showed a linear TL dose-response in the range from 1 mGy to 1 kGy. The TL analysis using a variable dose method revealed first order kinetics for both the peaks. Trap depth and frequency factor for peak-1 were found to be 0.81 eV and 5.2×10⁹ s⁻¹, whereas for peak-2 the values were 1.7 eV and 1.7×10¹⁶ s⁻¹, respectively.