Construction of an electron analyzer with a wide acceptance solid angle

We have developed a new electron energy analyzer with a large solid angle of 0.14π, which is comparable to that of cylindrical mirror analyzer. Typical energy resolution was ΔE/E₀ ∼ 0.016 for the aperture of 1 mm and central radius of 100 mm, and typical angular resolution was less than 0.5°.     

Photoinduced effect in Ga-Ge-S based thin films

Glassy films of Ga₁₀Ge₂₅S₆₅ with 4 μm thickness were deposited on quartz substrates by electron beam evaporation. Photoexpansion (PE) (photoinduced increase in volume) and photobleaching (PB) (blue shift of the bandgap) effects have been examined. The exposed areas have been analyzed using perfilometer and an expansion of 1.7 μm (ΔV/V ≈ 30%) is observed for composition Ga₁₀Ge₂₅S₆₅ exposed during 180 min and 3 mW/cm² power density. The optical absorption edge measured for the film Ge₂₅Ga₁₀S₆₅ above and below the bandgap show that the blue shift of the gap by below bandgap photon illumination is considerable higher (ΔE_g = 440 meV) than ΔE_g induced by above bandgap illumination (ΔE_g = 190 meV). The distribution of the refraction index profile showed a negative change of the refraction index in the irradiated samples (Δn = −0.6). The morphology was examined using a scanning electron microscopy (SEM). The chemical compositions measured using an energy dispersive analyzer (EDX) indicate an increase of the oxygen atoms into the irradiated area. Using a Lloyd's mirror setup for continuous wave holography it was possible to record holographic gratings using the photoinduced effects that occur in them. Diffraction efficiency up to 25% was achieved for the recorded gratings and atomic force microscopy images are presented.     

Effect of the competition between relaxation and core hole decay on the Auger-photoelectron coincidence spectroscopy (APECS) spectrum of Ni metal

The valence hole created in Ni metal either by the L2-L3V Coster–Kronig (CK) transition or by the L3V shakeup/off becomes screened out prior to the L3-hole decay. We denote the atomic shell Lx (x = 2, 3) by LX. The metastable two-hole L3V state relaxes to the fully relaxed single L3-hole state before the L3-hole decays. Thus, the coincidence L2-L3(V)-VV(V) Auger-electron spectrum resembles closely the coincidence L3-VV Auger-electron spectrum. The final state of the CK transition preceded Auger transition is a two-hole state rather than a three-hole state. The four-hole satellite about 8 eV below the L3-VV main line in the singles (non-coincidence) Auger-electron spectrum is partly due to the L3VV-VVVV transition and the L2-L3VV-VVVV transition. The valence holes created either by the L2-L3VV transition or by the L3VV double shakeup/off remain localized during the L3-hole decay. The L3-hole lifetime widths of Fe, Co and Ni metals are determined from the APECS spectra. The agreement between experiment and theory (the independent-particle approximation) is poor.     

Advances in crystal analyzers for inelastic X-ray scattering

The realization of spherical crystal analyzers for inelastic X-ray scattering experiments (IXS) is an ongoing project at the ESRF since 1992. We developed reliable techniques to routinely produce silicon spherical analyzers with very high (ΔE=1÷10 meV) and high energy resolution (ΔE=0.2÷1.5 eV), and with very good focal properties and efficiency. In this article we report the state of the art of the analyzer construction and the main improvements made during the last years.     

Adsorption and reaction of bicyclic hydrocarbons at Pt(1 1 1) and Sn/Pt(1 1 1) surface alloys: trans-decahydronaphthalene (C10H18) and bicyclohexane (C12H22)

Adsorption and desorption of trans-decahydronaphthalene (C₁₀H₁₈) and bicyclohexane (C₁₂H₂₂) can be used to probe important aspects of non-specific dehydrogenation leading to surface carbon accumulation and establish better estimates of activation energies for C-H bond cleavage at Pt-Sn alloys. This chemistry was studied on Pt(1 1 1) and the (2 × 2)-Sn/Pt(1 1 1) and (√3 × √3)R30°-Sn/Pt(1 1 1) surface alloys by using temperature programmed desorption (TPD) mass spectroscopy and Auger electron spectroscopy (AES). These hydrocarbons are reactive on Pt(1 1 1) surfaces and fully dehydrogenate at low coverages to produce H₂ and surface carbon during TPD. At monolayer coverage, 87% of adsorbed C₁₀H₁₈ and 75% C₁₂H₂₂ on Pt(1 1 1) desorb with activation energies of 70 and 75 kJ/mol, respectively. Decomposition of C₁₀H₁₈ is totally inhibited during TPD on these Sn/Pt(1 1 1) alloys and decomposition of C₁₂H₂₂ is reduced to 10% of the monolayer coverage on the (2 × 2)-Sn/Pt(1 1 1) alloy and totally inhibited on the (√3 × √3)R30°-Sn/Pt(1 1 1) alloy. C₁₀H₁₈ and C₁₂H₂₂ are more weakly chemsorbed on these two alloys compared to Pt(1 1 1) and these molecules desorb in narrow peaks characteristic of each surface with activation energies of 65 and 73 kJ/mol on the (2 × 2) alloy and 60 and 70 kJ/mol on the (√3 × √3)R30°-Sn/Pt(1 1 1) alloy, respectively. Alloyed Sn has little influence on the monolayer saturation coverage of these two molecules, and this is decreased only slightly on these two Sn/Pt(1 1 1) alloys. The use of these two probe molecules enables an improved estimate of the activation energy barriers E* to break aliphatic C-H bonds in alkanes on Sn/Pt alloys; E* = 65-73 kJ/mol on the (2 × 2)-Sn/Pt(1 1 1) alloy and E* ? 70 kJ/mol on the (√3 × √3)R30°-Sn/Pt(1 1 1) alloy.     

Alloy formation of Co/Ni/Pt(1 1 1)

The initial growth and alloy formation of ultrathin Co films deposited on 1 ML Ni/Pt(1 1 1) were investigated by Auger electron spectroscopy (AES), low energy electron diffraction (LEED), and ultraviolet photoelectron spectroscopy (UPS). A sequence of samples of d_Co Co/1 ML Ni/Pt(1 1 1) (d_Co = 1, 2, and 3 ML) were prepared at room temperature, and then heated up to investigate the diffusion process. The Co and Ni atoms intermix at lower annealing temperature, and Co-Ni intermixing layer diffuses into the Pt substrate to form Ni-Co-Pt alloys at higher annealing temperature. The diffusion temperatures are Co coverage dependent. The evolution of UPS with annealing temperatures also shows the formation of surface alloys. Some interesting LEED patterns of 1 ML Co/1 ML Ni/Pt(1 1 1) show the formation of ordered alloys at different annealing temperature ranges. Further studies in the Curie temperature and concentration analysis, show that the ordered alloys corresponding to different LEED patterns are Ni_xCo_1−xPt and Ni_xCo_1−xPt₃. The relationship between the interface structure and magnetic properties was investigated.     

(e,2e) and (e,3-1e) coincidence experiments for studying the PCI effect of low energy ionizing electrons in the Auger process of Ar

Our (e,3-1e) measurements for studying the post-collision interaction (PCI) after electron impact inner shell ionization of argon were continued and completed at different energy conditions. Emitted LMM Auger electrons are detected in coincidence with the ionizing scattered electrons and the energy of the slow PCI inducer ejected electron was calculated from energy conservation. Particularly the effect of the very low energy (i.e. 0–5 eV) ejected electrons (strongly asymmetric energy sharing) is studied at 500 and 460 eV primary electron energies. In the latter case, the background caused by outer-shell electrons was measured by itself and then removed from the coincident spectrum. Nevertheless, the evaluation of PCI distorted Auger lines is still considerably disturbed by the resonant Auger electrons from the high Rydberg states, their (e,2e) contribution was estimated in the paper.     

Scanning tunneling spectroscopy and break junction spectroscopy on iron-oxypnictide superconductor NdFeAs(O0.9F0.1)

Iron-oxypnictide superconductor NdFeAs(O_0.9F_0.1) was studied using both low-temperature scanning tunneling microscopy/spectroscopy (STM/STS) and tunnel break junction (BJ) methods. STM topography showed granular and spot structures with a typical size of several nanometers, most probably governed by fluorine atom distribution. The majority of STS conductance, G, versus voltage, V, curves revealed V-shaped structures, whereas some of G(V) dependences possessed coherent gap peaks or kinks at gap energies. At the same time, G(V) dependences obtained by the BJ technique showed clear-cut coherence peaks with peak-to-peak distances V_pp = 4Δ/e ∼ 25 mV at 4.2 K, where Δ is the superconducting energy gap, e > 0 is the elementary charge. This yields Δ(0) = 6–7 meV, so that the ratio 2Δ(0)/k_BT_c is about 3–4, k_B being the Boltzmann constant. This value is consistent with the conventional weak-coupling s-wave Bardeen–Cooper–Schrieffer theory.     

CO2 adsorption on Cr(1 1 0) and Cr2O3(0 0 0 1)/Cr(1 1 0)

We attempt to correlate qualitatively the surface structure with the chemical activity for a metal surface, Cr(1 1 0), and one of its surface oxides, Cr₂O₃(0 0 0 1)/Cr(1 1 0). The kinetics and dynamics of CO₂ adsorption have been studied by low energy electron diffraction (LEED), Aug er electron spectroscopy (AES), and thermal desorption spectroscopy (TDS), as well as adsorption probability measurements conducted for impact energies of E_i = 0.1-1.1 eV and adsorption temperatures of T_s = 92-135 K. The Cr(1 1 0) surface is characterized by a square shaped LEED pattern, contamination free Cr AES, and a single dominant TDS peak (binding energy E_d = 33.3 kJ/mol, first order pre-exponential 1 × 10¹³ s⁻¹). The oxide exhibits a hexagonal shaped LEED pattern, Cr AES with an additional O-line, and two TDS peaks (E_d = 39.5 and 30.5 kJ/mol). The initial adsorption probability, S₀, is independent of T_s for both systems and decreases exponentially from 0.69 to 0.22 for Cr(1 1 0) with increasing E_i, with S₀ smaller by ∼0.15 for the surface oxide. The coverage dependence of the adsorption probability, S(Θ), at low E_i is approx. independent of coverage (Kisliuk-shape) and increases initially at large E_i with coverage (adsorbate-assisted adsorption). CO₂ physisorbs on both systems and the adsorption is non-activated and precursor mediated. Monte Carlo simulations (MCS) have been used to parameterize the beam scattering data. The coverage dependence of E_d has been obtained by means of a Redhead analysis of the TDS curves.     

Influence of ophthalmic lenses in the illuminance originated at a peripheral glare source and reaching the eye

To study the influence of glare on the visual performance of a subject wearing an ophthalmic lens, it is useful to know how the lens affects the illuminance reaching the eye. In this paper, considering spherical standard ophthalmic lenses and defining the relative illuminance, E_r, as the quotient between the illuminance at the cornea with and without lens, a methodology to evaluate E_r in terms of easily determined parameters is developed. Three effects are considered, pupil size variation of the system with and without lens; lateral shifts of rays transmitted through the lens and reflections at the lens. Calculations are experimentally verified employing 5 organic ophthalmic lenses of ±6; ±4 and 0.12 dioptres and 2 glass plane parallel plates 1.95 and 6.6 mm thick. Using a photometer whose sensor is 12 mm apart from the lens and 740 mm apart from a glare source subtending an eccentricity angle of 9.6°, it results E_r=1.204 for the 6 dioptres lens and E_r=0.803 for the −6 dioptres one if sensor diameter is 10 mm while, for a 719 mm distance and a 10° angle, E_r=0.922 for the thin plate and a 30 mm sensor and E_r=1.006 for the thick plate and a 10 mm sensor. Experimental and theoretical results differ in less than 3%.     

Oxidation and thermal reduction of the Cu(1 0 0) surface as studied using positron annihilation induced Auger electron spectroscopy (PAES)

Changes in the surface of an oxidized Cu(1 0 0) single crystal resulting from vacuum annealing have been investigated using positron annihilation induced Auger electron spectroscopy (PAES). PAES measurements show a large increase in the intensity of the annihilation induced Cu M_2,3VV Auger peak as the sample is subjected to a series of isochronal anneals in vacuum up to annealing temperature 300 °C. The intensity then decreases monotonically as the annealing temperature is increased to ∼600 °C. Experimental probabilities of annihilation of surface-trapped positrons with Cu 3p and O 1s core-level electrons are estimated from the measured intensities of the positron annihilation induced Cu M_2,3VV and O KLL Auger transitions. Experimental PAES results are analyzed by performing calculations of positron surface states and annihilation probabilities of surface-trapped positrons with relevant core electrons taking into account the charge redistribution at the surface, surface reconstructions, and electron-positron correlations effects. The effects of oxygen adsorption on localization of positron surface state wave function and annihilation characteristics are also analyzed. Possible explanation is proposed for the observed behavior of the intensity of positron annihilation induced Cu M_2,3VV and O KLL Auger peaks and probabilities of annihilation of surface-trapped positrons with Cu 3p and O 1s core-level electrons with changes of the annealing temperature.     

Many-body effect in the coincidence L3 and M3 photoelectron spectroscopy spectra of Cu metal

The coincidence L₃ and M₃ photoelectron spectroscopy (PES) main lines of Cu metal are calculated by a many-body theory. There is no peak-energy shift between the singles PES main line and the coincidence one. The asymmetric narrowing of the coincidence PES main line on the low kinetic energy (KE) side is very small. This is in accord with recent experimental findings. In Cu metal, the shakeup satellite intensity is small and the main-line satellite separation energy is much larger than the core–hole lifetime width. The interference via the final-state interaction is negligible. In the PES main line, the imaginary part of the self-energy by shakeup excitations, which is very small compared to the core–hole lifetime width, decreases very slowly in linear with photoelectron KE. The branching ratio of Auger decay of a single hole state then increases very slowly in linear with photoelectron KE so that the deviation of the coincidence PES main line from the singles one is very small. The 939 eV structure seen only in the coincidence L₃ PES spectrum of Cu metal is attributed to the enhancement of the inelastic peak of a smaller energy loss due to electrons of a smaller average emission depth measured in coincidence with the elastic Auger peak. The structure will not be enhanced in the singles PES spectrum. The background subtraction in the coincidence spectrum cannot be the same as that in the singles one. Such consideration is necessary before we can conclude about the asymmetric narrowing on the low KE side. A unique capability of APECS by which one can determine the photoelectron KE dependent part of the imaginary part of the self-energy is pointed out.     

Many-body effect in the N23-VV Auger-photoelectron coincidence spectroscopy (APECS) spectra of Ag metal

The coincidence N23-VV Auger-electron spectroscopy (AES) spectra and N23 photoelectron spectroscopy (PES) spectra of Ag metal are analyzed. Here NX is the notation for atomic shell Nx (X = 2, 3). The band-like feature in the coincidence N23-VV AES spectra is much more intense than that in the coincidence M45-VV ones because the potential in the delocalized two-hole state is less attractive than that in the localized one. The partial N23-VV super Coster–Kronig (sCK) transition rate depends critically on both the final-state potential and the sCK-electron kinetic energy (KE) because the KE is low, whereas the partial M45-VV Auger-transition rate is fairly independent of them because the KE is very high. As a result, the partial sCK-transition rate to the band-like state is enhanced compared to that to the atomic-like localized state. The low KE tail in the coincidence N23-VV AES spectra which is likely due to the sCK transition involving more than two electrons, is more enhanced than that in the coincidence M45-VV ones. This is due to the enhancement of the partial sCK-transition rate by the presence of extra holes in the final state. The sharp peaks of small intensity on the lower KE side of the main line in the coincidence N2 PES spectrum are tentatively attributed to the shakeup satellites.     

Adsorption of glycine on a NiAl(1 1 0) alloy surface

The adsorption and desorption of glycine (NH₂CH₂COOH), vacuum deposited on a NiAl(1 1 0) surface, were investigated by means of Auger electron spectroscopy (AES), low energy electron diffraction (LEED), temperature-programmed desorption, work function (Δφ) measurements, and ultraviolet photoelectron spectroscopy (UPS). At 120 K, glycine adsorbs molecularly forming mono- and multilayers predominantly in the zwitterionic state, as evidenced by the UPS results. In contrast, the adsorption at room temperature (310 K) is mainly dissociative in the early stages of exposure, while molecular adsorption occurs only near saturation coverage. There is evidence that this molecularly adsorbed species is in the anionic form (NH₂CH₂COO⁻). Analysis of AES data reveals that upon adsorption glycine attacks the aluminium sites on the surface. On heating part of the monolayer adsorbed at 120 K is converted to the anionic form and at higher temperatures dissociates further before desorption. The temperature-induced dissociation of glycine (<400 K) leads to a series of similar reaction products irrespective of the initial adsorption step at 120 K or at 310 K, leaving finally oxygen, carbon and nitrogen at the surface. AES and LEED measurements indicate that oxygen interacts strongly with the Al component of the surface forming an “oxide”-like Al-O layer.     

A novel demonstration of photoacoustic Raman spectroscopy with combined stimulated Raman pumping in H2 molecule

We present the experimental demonstration of a novel, efficient, and vibrational selective technique to prepare population in vibrational level v″ = 1 using the stimulated Raman pumping. Photoacoustic Raman signal has been studied in non-radiative transitions in the molecule H₂ (v″ = 0) and (v″ = 1). The population fraction in the v″ = 1 level can be estimated by using combined photoacoustic Raman spectroscopy with stimulated Raman pumping for the first time.     

Ellipsometric investigation of optical constant and energy band gap of Zn1−xMnxSe/GaAs (1 0 0) epilayers

Zn_1−xMn_xSe/GaAs (1 0 0) epilayers were grown using a hot-wall epitaxy method. The spectroscopic ellipsometry was used to determine the optical dielectric constant. The obtained pseudodielectric function spectra revealed the distinct structures at energies of E₀, E₀ + Δ₀, E₁, E₁ + Δ₁, E₂ and  + Δ₀ critical points (CPs) at lower Mn composition range. These critical points were determined by analytical line-shapes fitted to numerically calculated derivatives of their pseudodielectric functions. The peak characteristics were changed with the change in Mn composition. The spectral dependence of pseudodielectric function 〈?〉 was used to obtain the fundamental energy gaps E₀ including a unique relation with Mn composition. Also, the shifting and broadening of the CPs were observed with increasing Mn composition.     

The millimeter-wave rotational spectrum of fluorobenzene

The room-temperature rotational spectrum of fluorobenzene was studied in the frequency region 167-318 GHz. Rotational transitions were assigned and measured in the ground vibrational state, and all six excited vibrational states with energies below 600 cm⁻¹, i.e., v₁₁ = 1, v₁₁ = 2, v_18b = 1, v_16a = 1, v_16b = 1, and v_6a = 1. Accurate quartic-level spectroscopic constants were determined for all states, allowing spectral predictions well into the submillimeter region. The states v_18b = 1 and v_16a = 1 were found to be connected by a strong Coriolis interaction, which allowed precise determination of their energy separation, ΔE = 7.455088(3) cm⁻¹. Unambiguous assignment of vibrational modes was made on the basis of the calculated inertial defect and nuclear spin statistical weights. Rotational constants for the ¹³C₄ isotopomer have also been redetermined and two new least-squares determinations of the geometry of fluorobenzene, r₀ and are reported.     

Growth of Co nanoparticles on a nanostructured θ-Al2O3 film on CoAl(1 0 0)

We have investigated the growth of Co nanoparticles on θ-Al₂O₃/CoAl(1 0 0) by means of Auger electron spectroscopy (AES), high-resolution electron energy loss spectroscopy (EELS), low energy electron diffraction (LEED) and scanning tunneling microscopy (STM). Due to Volmer-Weber growth, Co forms particles with a mean diameter of approximately 2.5 nm and height of 0.8 nm. Even on the entirely covered oxide, there is no Ostwald ripening and Co particles stay structurally isolated. The nanoparticles exhibit a small size distribution and tend to form chains, as predetermined by the streak structure of the oxide template. For sufficient high coverages Co-core-CoO-shell nanoparticles may be evidenced, which is explained as a result of surfactant oxygen. The nanostructured particles may open the door to numerous applications, such as in catalysis and magnetoelectronic applications, where large areas of ordered nanodots are desired.     

Growth mode and electronic structure of Au nano-clusters on NiO(0 0 1) and TiO2(1 1 0)

The growth mode and electronic structure of Au nano-clusters grown on NiO and TiO₂ were analyzed by reflection high-energy electron diffraction, a field-emission type scanning electron microscope, medium energy ion scattering and photoelectron spectroscopy. Au was deposited on clean NiO(0 0 1)-1 × 1 and TiO₂(1 1 0)-1 × 1 surfaces at room temperature with a Knudsen cell at a rate of 0.25-0.35 ML/min (1 ML = 1.39 × 10¹⁵ atoms/cm²:Au(1 1 1)). Initially two-dimensional (2D) islands with thickness of one Au-atom layer grow epitaxially on NiO(0 0 1) and then neighboring 2D-islands link each other to form three-dimensional (3D)-islands with the c-axis oriented to the [1 1 1] direction. The critical size to form 3D-islands is estimated to be about 5 nm². The shape of the 3D-islands is well approximated by a partial sphere with a diameter d and height h ranging from 2.0 to 11.8 nm and from 0.95 to 4.2 nm, respectively for Au coverage from 0.13 to 4.6 ML. The valence band spectra show that the Au/NiO and Au/TiO₂ surfaces have metallic characters for Au coverage above 0.9 ML. We observed Au 4f spectra and found no binding energy shift for Au/NiO but significant higher binding energy shifts for Au/TiO₂ due to an electron charge transfer from Au to TiO₂. The work function of Au/NiO(0 0 1) gradually increases with increase in Au coverage from 4.4 eV (NiO(0 0 1)) to 5.36 eV (Au(1 1 1)). In contrast, a small Au deposition(0.15 to 1.5 ML) on TiO₂(1 1 0) leads to reduction of the work function, which is correlated with an electron charge transfer from Au to TiO₂ substrate.     

Fourier transform spectroscopy of new emission systems of NbN in the visible region

The emission spectrum of NbN has been reinvestigated in the 8000-35 000  cm⁻¹ region using a Fourier transform spectrometer and two groups of new bands were observed. The bands observed in the 18 000-20 000 cm⁻¹ region have been assigned to a new ³Π-X³Δ transition. Three bands with R heads near 19 463.8, 19 659.0 and 19 757.0 cm⁻¹ have been assigned as 0-0 bands of the ³Π₂-X³Δ₃, ³Π₁-X³Δ₂ and ³Π_0±-X³Δ₁ subbands, respectively, of this new transition. Three additional ΔΩ = 0 bands have been observed in the 24 000-26 000  cm⁻¹ region. A 0-0 band with an R head near 25 409.9 cm⁻¹ has been assigned as a ΔΩ = 0 transition having X³Δ₂ as its lower state while two additional bands with heads near 25 518.7 and 25 534.8 cm⁻¹ were found to be ΔΩ = 0 bands having X³Δ₁ as the common lower state. Two of these three bands are perhaps subbands of a ³Δ-X³Δ transition. Most of the excited levels are affected by perturbations.