The interaction of Fe on MgO(1 0 0) surfaces

The atomic interaction and magnetic properties of ultrathin Fe films grown on cleaved and polished MgO(1 0 0) surfaces were studied by conversion electron Mössbauer spectroscopy (CEMS). ⁵⁷Fe layers were deposited as probe atoms in different layer positions in 10 ML thick Fe films. Fe layers of different thicknesses were formed on polished and cleaved substrate surfaces at RT deposition. The analysis of the spectra showed no Fe-O^2- interaction in MgO/Fe interface. FeO phase formation was excluded. The Mössbauer spectrum of 5 ML ⁵⁷Fe sample showed enhanced internal magnetic field at 80 K. No interdiffusion of ⁵⁷Fe and ⁵⁶Fe atoms was observed between the layers at room temperature.     

Structural and electronic properties of thin Ni layers on Cu(1 1 1) as investigated by ARPES, STM and GIXD

The growth and the crystalline and electronic structure of Ni deposited on single crystalline Cu(1 1 1) were studied by scanning tunnelling microscopy (STM), grazing incidence X-ray diffraction (GIXD) and angle-resolved photoemission spectroscopy (ARPES). In the early stages of growth monoatomic-high flat Ni islands, partially covered by Cu migrating from the surface, are observed. Starting from a pseudomorphic epitaxial relationship the in-plane lattice parameter progressively relaxes with increasing coverage. For a 20 monolayer (ML) thick deposit the in-plane lattice parameter is still found halfway between the bulk Ni and Cu lattice parameters. ARPES data also rule out the layer-by-layer growth and provide the values of the Ni exchange splitting.     

Non-collinear magnetisation of V clusters supported on a Cu (1 1 1) surface: Theory

Magnetic properties and electronic structure of V clusters supported on a Cu (1 1 1) substrate, have been calculated from a first principles method. We observe in general non-collinear magnetic structures that are the result of antiferromagnetic interactions on a frustrated lattice. The values of the magnetic moments range from ∼0 to 2.7 μ_B/atom, depending on cluster geometry.     

Atom geometry of nanostructured Fe films grown on c(2 × 2)-N/Cu(1 0 0) surface: An investigation by X-ray absorption spectroscopy with multishell analysis

We investigated the growth of Fe nanostructured films on c(2 × 2)-N/Cu(1 0 0) surface with Fe K-edge X-ray absorption fine structure (XAFS) in the near edge and in the extended energy region. The high photon flux of the incident X-rays allowed us to perform multishell analysis of the XAFS oscillations for Fe coverage Θ_Fe < 1 ML. This data analysis yields a detailed investigation of the atom geometry and some insights in the film morphology. At Θ_N < 0.5 ML (N saturation coverage) there is absence of contribution to XAFS from N atoms. First shell analysis of linearly polarized XAFS gives Fe-Fe (or Fe-Cu) bond length values varying between R₁ = 2.526 ± 0.006 Å at the highest Fe coverage (3 ML ) and R₁ = 2.58 ± 0.01 Å at Θ_Fe = 0.5 ML, Θ_N = 0.3 ML, with incidence angle Θ = 35°. These values are different from the case of bcc Fe (R = 2.48 Å), and compatible with fcc Fe (R₁ = 2.52 Å) and fcc Cu (R₁ = 2.55 Å). At the Fe lowest coverage (Θ_Fe = 0.5 ML) the dependence of R₁ on the incidence angle indicates expansion of the outmost layer. Near edge spectra and multishell analysis can be well reproduced by fcc geometry with high degree of static disorder. At N saturation pre-coverage (Θ_N = 0.5 ML) the XAFS analysis has to keep into account the Fe-N bonding. The results suggest two different adsorption sites: one with Fe in a fcc hollow site, surrounded by other metal atoms as nearest neighbours, and one resulting from an exchange with a Cu atom underneath the N layer.     

Reflectance difference spectroscopy study of Ag growth on W(1 1 0)

We report a reflectance difference spectroscopy (RDS) investigation of the epitaxial growth of Ag on the W(1 1 0) surface. Monitoring the growth in real time, the RDS signal at 4.6 eV shows an oscillatory behavior corresponding to the layer-by-layer growth of the first three monolayers. The oscillations are attributed to the variation of the optical anisotropy contributed by the W(1 1 0) substrate and the Ag film. By analyzing the spectral evolution during growth, characteristic optical-electronic fingerprints can be deduced for each added atomic layer. In particular, the binding energy of d-like quantum well states has been used as an indicator for the number of Ag atomic layers and, hence, as a sensitive probe of the Ag thin film growth.     

Ab-initio calculations and STM observations on tetrapyridyl and Fe(II)-tetrapyridyl-porphyrin molecules on Ag(1 1 1)

We modelled the adsorption of tetra-pyridyl-porphyrin (TPyP) and Fe(II)-tetra-pyridyl- porphyrin (Fe-TPyP) molecules on Ag(1 1 1). TPyP adsorbs in a flat geometry at a distance of 5.6 Å from the surface. The dihedral angle of the pyridyl rings is found to be 70°. The molecular structure remains largely unaffected by the adsorption. The structure of the molecular adlayer should thus be determined mainly by lateral intermolecular interactions. These conclusions are confirmed by scanning tunnelling microscopy observations. Upon metalation spin-polarized states with strong Fe d-character appear in Fe-TPyP near the centre of the gap between the highest occupied and the lowest unoccupied states of a TPyP molecule. We find also that the gap is widened in the presence of Fe. This implies a shift of 0.3 eV of unoccupied states as identified by scanning tunnelling spectroscopy simulations and confirmed by experimental data.     

Structure and magnetism of bcc(1 1 0)-like Fe films grown on Cu(0 0 1) via ion beam triangulation and spin-polarized electron capture

The structure and magnetism of thin epitaxial Fe layers grown on Cu(0 0 1) is investigated by grazing scattering of fast H and He atoms. Information on the atomic structure of the film and substrate surfaces is obtained by making use of ion beam triangulation with protons. The magnetic behavior is studied via the polarization of light emitted after capture of spin-polarized electrons into excited atomic terms during scattering of He atoms. For the formation of bcc(1 1 0)-like Fe films at higher coverages, we detect differences in structural and magnetic properties for room and low temperature growth. We suggest that the crystalline structure depends on the film morphology and that Cu impurities affect the magnetic properties.     

Effect of surface chemisorption on the spin reorientation transition in magnetic ultrathin Fe film on Ag(0 0 1)

We have investigated the effect of surface chemisorption on the spin reorientation transitions in magnetic ultrathin Fe films on Ag(0 0 1) by means of the polar and longitudinal magneto-optical Kerr effect (MOKE) and X-ray magnetic circular dichroism (XMCD) measurements. It is found by the MOKE that adsorption of O₂ and NO induces the shift of the critical thickness for the transitions to a thinner side, together with the suppression of the remanent magnetization and the coercive field of the Fe film. This implies destabilization of the perpendicular magnetic anisotropy. On the other hand, H₂ adsorption is found not to change the magnetic anisotropy, though the enhancement of the coercive field is observed. The XMCD reveals that although both the spin and orbital magnetic moments along the surface normal are noticeably reduced upon O₂ and NO adsorption, the reduction of the orbital magnetic moments are more significant. This indicates that the destabilization of the perpendicular magnetic anisotropy upon chemisorption of O₂ and NO originates from the change of the spin-orbit interaction at the surface.     

Mössbauer spectroscopy and magnetic properties in thin films of FexNi100−x electroplated on silicon (1 0 0)

Fe_xNi_100−x thin films were produced by galvanostatic electrodeposition on Si (1 0 0), nominal thickness 2800 nm, and x ranging 7-20. The crystalline structure of the sample was determined by X-ray diffraction (XRD). The magnetic properties were investigated by vibration sample magnetometry (VSM) and room temperature ⁵⁷Fe Mössbauer spectroscopy. Conversion Electron Mössbauer spectroscopy (CEMS) in both film surfaces for the thick self-supported films showed that the magnetic moment direction is in the plane and conventional transmission (MS) that the directions are out of the plane films. The results were interpreted assuming a three-layer model where the external layer has in-plane magnetization and the internal one, out of plane magnetization.     

Four-fold magnetic anisotropy in a Co film on MgO(0 0 1)

The development of devices based on magnetic tunnel junctions has raised new interests on the structural and magnetic properties of the interface Co/MgO. In this context, we have grown ultrathin Co films (≤30 Å) by molecular-beam epitaxy on MgO(0 0 1) substrates kept at different temperatures (T_S). Their structural and magnetic properties were correlated and discussed in the context of distinct magnetic anisotropies for Co phases reported in the literature. The sample characterization has been done by reflection high energy electron diffraction, magneto-optical Kerr effect and ferromagnetic resonance. The main focus of the work is on a sample deposited at T_S=25 °C, as its particular way of growth has enabled a bct Co structure to settle on the substrate, where it is not normally obtained without specific seed layers. This sample presented the best crystallinity, softer magnetic properties and a four-fold in-plane magnetic anisotropy with Co〈1 1 0〉 easy directions. Concerning the samples prepared at T_S=200 and 500° C, they show fcc and polycrystalline structures, respectively and more intricate magnetic anisotropy patterns.     

Fourfold in-plane magnetic anisotropy in epitaxial Fe(1 1 0)/Cu(0 0 1) and Fe(1 1 0)/Ni(0 0 1) bilayers

Epitaxial Fe(1 1 0) films with thicknesses of 100-800 nm on Cu(0 0 1) and Ni(0 0 1) buffer layers grown on MgO(0 0 1) substrates have been fabricated. These films contain Fe(1 1 0) crystallites which are in the Pitsch orientation relationship. Magnetization and the fourfold in-plane magnetic anisotropy constants of these films have been determined by torque measurements. All the samples under study are characterized by a fourfold magnetic anisotropy with easy axes parallel to the [1 0 0] and [0 1 0] directions of Cu(0 0 1) and Ni(0 0 1) layers. The measured values of the constant for Fe(1 1 0)/Cu(0 0 1) are found to depend on deposition temperature; a maximum value of (2.5±0.1)×10⁵ erg/cm³ is reached after annealing at 600 °С. The in-plane torque measurements on Fe(1 1 0)/Ni(0 0 1) bilayers obtained at 300 °С, on the other hand, exhibit a constant value of (2.7±0.1)×10⁵ erg/cm³. Assuming an exchange interaction between the Fe(1 1 0) crystallites, which are in the Pitsch orientation relationship, the fourfold in-plane magnetic anisotropy has been calculated as 2.8×10⁵ erg/cm³. The deviations of the experimental values from the predicted one may be explained by the formation of a polycrystalline phase within the Fe(1 1 0) layer and a partial disorientation of the epitaxial crystallites.     

The magnetic map of NiMn alloy thin films on Co(0 0 1) and Co(1 1 1)

Following the experimental work of Groudeva-Zotova et al. [S. Groudeva-Zotova, D. Elefant, R. Kaltofen, D. Tietjen, J. Thomas, V. Hoffmann, C.M. Schneider, J. Magn. Magn. Mater. 263 (2003) 57] where the magnetic and structural characteristics of a bi-layer NiMn-Co exchange biasing systems was investigated, density functional calculations with generalized gradient corrections were performed on (Mn_0.5Ni_0.5)_n ordered alloy on Co(0 0 1) and one Mn_1−xNi_x monolayer on Co(1 1 1). For the Mn_0.5Ni_0.5 monolayer on Co(0 0 1), magnetic moments per surface atom of 0.65 μ_B and 3.76 μ_B were obtained for Ni and Mn, respectively. Those magnetic moments are aligned parallel to the total moment of Co(0 0 1). A complex behavior of the Mn moment in dependence of the thickness “n” is obtained for (Mn_0.5Ni_0.5)_n on Co(0 0 1). Investigations on Mn_1−xNi_x monolayer on Co(1 1 1) have shown that the crystallographic orientation does not modify significantly neither the magnetic moments of Mn and Ni atoms nor their ferromagnetic coupling with the Co(1 1 1) substrate, except for x = 0.66. For x = 0.66 the Mn sub-lattice presents an antiferromagnetic coupling leading to a quenching of the Ni magnetic moment.     

Growth mode and novel structure of ultra-thin KCl layers on the Si(1 0 0)-2 × 1 surface

This study investigates ultra-thin potassium chloride (KCl) films on the Si(1 0 0)-2 × 1 surfaces at near room temperature. The atomic structure and growth mode of this ionic solid film on the covalent bonded semiconductor surface is examined by synchrotron radiation core level photoemission, scanning tunneling microscopy and ab initio calculations. The Si 2p, K 3p and Cl 2p core level spectra together indicate that adsorbed KCl molecules at submonolayer coverage partially dissociate and that KCl overlayers above one monolayer (ML) have similar features in the valance band density of states as those of the bulk KCl crystal. STM results reveal a novel c(4 × 4) structure at 1 ML coverage. Ab initio calculations show that a model that comprises a periodic pyramidal geometry is consistent with experimental results.     

Self-aligned silicon quantum wires on Ag(1 1 0)

Upon deposition of silicon onto the (1 1 0) surface of a silver crystal we have grown massively parallel one-dimensional Si nanowires. They are imaged in scanning tunnelling microscopy as straight, high aspect ratio, nanostructures, all with the same characteristic width of 16 Å, perfectly aligned along the atomic troughs of the bare surface. Low energy electron diffraction confirms the massively parallel assembly of these self-organized nanowires. Photoemission reveals striking quantized states dispersing only along the length of the nanowires, and extremely sharp, two-components, Si 2p core levels. This demonstrates that in the large ensemble each individual nanowire is a well-defined quantum object comprising only two distinct silicon atomic environments. We suggest that this self-assembled array of highly perfect Si nanowires provides a simple, atomically precise, novel template that may impact a wide range of applications.     

Structural study of Co/Pd(1 1 1) and CO/Co/Pd(1 1 1) by surface X-ray absorption fine structure spectroscopy

The structure of the Co thin films on Pd(1 1 1) and the effect of the CO adsorption on Co thin films were studied by Co K-edge surface X-ray absorption fine structure (XAFS). The polarization dependences of the X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) spectra indicate that Co thin films grow in the fcc stacking mode on Pd(1 1 1) up to 12 ML. The analysis of the nearest neighbor shell shows little mechanical strain at the interface, indicating that Co atom does not grow pseudomorphically on Pd(1 1 1). There is no alloy-like structure at the interface. CO adsorption causes no structural change of the Co thin films but modifies the Co surface electronic state. These structural studies provide deep insight in the magnetic property of the Co thin films on Pd(1 1 1).     

High-Energy Ball Milling of NiAl(Fe) System

High-energy ball milling was used to promote the solubilization of iron into NiAl powder for an iron concentration range of 10–30 wt.%. The microstructural evolution induced by the intense mechanical deformations, under different milling conditions, was followed by X-ray diffraction and Mössbauer spectroscopy. The Mössbauer spectra are dominated by a magnetic sextet of about 33 T. Increasing the time and the speed of milling gives rise to a non-resolved doublet, having parameters typical of a NiAl compound with Fe atoms in solution. At the same time a reduction of lattice parameter occurs, which can be correlated to composition variations and partial disordering of the NiAl structure. Subsequent annealing modifies the Mössbauer spectra noticeably. In particular, the non-magnetic component becomes a broad singlet. Both diffraction analysis and Mössbauer spectroscopy indicate that a fcc Ni(Al,Fe) solid solution is forming in samples milled in agate. It is observed that the grain size of the milled products remains in the nanometric range even after thermal treatment, which adds interest to possible applications.     

Magnetic study of nanostructured zinc ferrite irradiated with 100 MeV O-beam

Nanostructured zinc ferrite of particle size 10 nm was synthesized by using the nitrates of appropriate cations and citric acid. This system was irradiated by 100 MeV oxygen beam with the fluence of 5×10¹³ ions/cm². The particle size of the system remains almost same after the irradiation. We observe decrease in magnetization of the sample after irradiation at 300 and 10 K. The nature of the σ-H plot shows the presence of superparamgnetic domains at 300 K even after irradiation. The blocking temperature decreases from 276 to 63 K after irradiation. The Mössbauer spectroscopy supports the presence of superparamgnetic domains at 300 K in both the samples. The decrease in magnetization after irradiation is attributed to the decrease in cation inversion and increase in canting angle as observed from in-field Mössbauer spectroscopy.     

Growth process and surface structure of MnSi on Si(1 1 1)

The solid-phase epitaxial growth process and surface structure of MnSi on Si(1 1 1) were investigated by coaxial impact-collision ion scattering spectroscopy (CAICISS) and atomic force microscopy (AFM). For the Si(1 1 1) sample deposited with 30 monolayers (ML) of Mn at room temperature, the intermixing of Mn and Si gradually started at 100 °C and reached equilibrium at approximately 400 °C. At this equilibrium state, the Mn atoms were transformed into crystalline MnSi film. Further annealing caused the desorption of Mn atoms. We identified the structure of MnSi as cubic B20 and the crystallographic orientation relationships as Si(1 1 1)//MnSi(1 1 1) and Si[]//MnSi[]. The MnSi(1 1 1) surface was found to have a dense Si terminating layer on its topmost surface. On the other hand, 3 ML of Mn deposited on Si(1 1 1) reacted with Si even at room temperature and formed a pseudomorphic structure. This structure was transformed into MnSi after annealing. A filmlike morphology with protrusions was observed for the sample with 30 ML of Mn, while island growth occurred for the sample with 3 ML of Mn.     

The growth and stability of Fe layers on the Mo(1 1 1) surface

The initial growth and the stability of Fe layers on the Mo(1 1 1) surface was studied with Auger electron spectroscopy, low energy electron diffraction, scanning tunneling microscopy and thermal desorption spectroscopy. At room temperature at least the first two monolayers grow layer-by-layer. The first layer is stable up to about 1200 K. Excess Fe starts to agglomerate at about 400 K and forms with increasing temperature thick flat-top islands which start to sublime at a somewhat below 1200 K. A strong decrease of the adsorption energy with coverage was found in the first monolayer. No {2 1 1} or { 1 1 0} micro-faceting could be seen at any coverage upon annealing.     

para-Sexiphenyl thin film growth on Cu(1 1 0) and Cu(1 1 0)-(2 × 1)O surfaces

We present a reflectance difference spectroscopy (RDS) study of para-sexiphenyl (p-6P) thin film growth on Cu(1 1 0) and Cu(1 1 0)-(2 × 1)O substrates. The RDS spectra show pronounced anisotropies for p-6P films formed on both substrates at room temperature, demonstrating that the molecules are uniaxially aligned within the films. Based on the RD spectra and the evolution of the optical transitions with p-6P coverage the growth mode on both substrates could be identified. From the dominating RDS feature, assigned to the lowest energy HOMO-LUMO transition, the orientation of the molecular chain can be determined. On Cu(1 1 0), the p-6P molecular chains align in the direction, i.e., along the Cu atomic rows, whereas on the Cu(1 1 0)-(2 × 1)O surface, the molecules are oriented in the orthogonal [0 0 1] direction, i.e., along the “added” Cu-O rows of the Cu(1 1 0)-(2 × 1)O surface. The energetic position and line shape of the main RDS feature differs for the two substrates and varies with p-6P coverage. This fine structure is discussed in terms of different molecular conformations, adlayer structure and vibronic replicas.