A novel spectrophotometric method for batch and flow injection determination of sulfite in beverages

A novel spectrophotometric assay method for batch and flow injection determination of sulfite in beverages is described. The method involves a reaction with diaquacobyrinic acid heptamethyl ester (diaquacobester, DACbs) in acetate buffer of pH 3 to form a highly stable sulfite cobester complex (SO₃Cbs). In the absence of sulfite, the reagent displays three absorption maxima at 349, 409 and 525 nm. Addition of sulfite is associated with the development of a new absorption band at 313 nm, an increase in the intensity of the band at 425 nm and a decrease in the absorbance of the bands at 349 and 525 nm. Variations of the absorptions at 313, 349, 425 and 525 nm are linearly proportional to sulfite concentrations over the range of 0.05–25 μg ml⁻¹with a detection limit of 0.01–0.2 μg ml⁻¹. Negligible interferences are caused by most common ions. Validation of the method according to the quality assurance standards shows suitability for quality control assessment of sulfite in complex matrices without prior treatment. The method has the advantages of high selectivity, good sensitivity, fast reaction, high stability of the reagent and reaction product and absorbance measurements at four different wavelengths in the same run. The method is successfully applied to determine the sulfite contents of some beverages. The results compare fairly well with data obtained using the standard method.     

Automatic flow systems based on sequential injection analysis for routine determinations in wines

Sequential injection systems for wine analysis have been developed in recent years for determination of more than 20 species. Several aspects of these systems are reviewed in the present paper. Special focus is given to implementation of in-line sample treatment and adaptation of system operation through software control to enable determination in different types of wine. The strategies used to enhance selectivity and the capacity for multi-parameter determination are also addressed.     

Gas diffusion sequential injection system for the spectrophotometric determination of free chlorine with o-dianisidine

A gas diffusion sequential injection system for spectrophotometric determination of free chlorine is described. The detection is based in the colorimetric reaction between free chlorine and a low toxicity reagent o-dianisidine. A gas diffusion unit is used to isolate free chlorine from the sample in order to avoid possible interferences. This feature results from the conversion of free chlorine to molecular chlorine (gaseous) with sample acidification. With minor changes in the operating conditions, two different dynamic ranges were obtained enhancing the application both to water samples and bleaches. The results obtained with the developed system were compared to the reference method, iodometric titration and proved not to be statistically different. A detection limit of 0.6 mg ClO⁻/L was achieved. Repeatability was evaluated from 10 consecutive determinations being the results better than 2%. The two dynamic ranges presented different determination rates: 15 h⁻¹ for 0.6-4.8 mg ClO⁻/L (water samples) and 30 h⁻¹ for 0.047-0.188 g ClO⁻/L (bleaches).     

Selective determination of cyanides by gas diffusion-stopped flow-sequential injection analysis and an on-line standard addition approach

A highly selective sequential injection (SI) method for the automated determination of weak-acid-dissociable cyanides is reported. The analytical procedure is based on the on-line reaction of the analyte with ninhydrin in carbonate medium to form a coloured product (λ_max = 510 nm). Cyanides are removed from sample matrix by acidification through a gas-diffusion step incorporated in the SI manifold. The effect of instrumental and chemical variables was studied. By adopting an on-line standard addition protocol, the sensitivity of the proposed method was enhanced drastically, without affecting the determination range. The assay was validated in terms of linearity (up to 200 μg L⁻¹), limit of detection (c_L = 2.5 μg L⁻¹), limit of quantitation (c_Q = 7.5 μg L⁻¹), precision (s_r < 2.5% at 100 μg L⁻¹) and selectivity. High tolerance against critical species such as sulfides and thiocyanates was achieved. The applicability of the method was demonstrated by analyzing tap and mineral water samples at levels below the limits established by international E.U. and U.S. organizations. The percent recoveries were satisfactory in all cases, ranging between 94.2 and 103.6%.     

Highly sensitive gas-diffusion sequential injection analysis based on flow manipulation

The present paper describes approaches utilizing the powerful flow manipulation capabilities of sequential injection analysis (SIA) to substantially improve the efficiency of gas-diffusion separation compared to its traditional implementation in flow injection analysis (FIA). Ammonia, ethylamine, diethylamine and triethylamine were used as model analytes in this study. Eleven flow manipulation approaches involving continuous flow, stop-flow, oscillating flow, and the introduction of air bubbles to separate the sample zone from the donor solution were tested. Improvement in sensitivity compared to traditional gas-diffusion FIA exceeding one order of magnitude was achieved. It was observed that this improvement increased with the molecular size of the analyte.     

A new approach for the sequential injection spectrophotometric determination of the total antioxidant activity

A sequential injection system based on the ABTS (2,2′-azino-bis-(3-ethylbenzothiazoline-6-sulphonic-acid) methodology was developed. The proposed method, incorporating a mixing chamber in the side port of the selection valve, was evaluated to measure the total antioxidant activity of several beverages and foods.The ABTS⁺ is generated by oxidation of ABTS with potassium persulfate and is reduced in presence of hydrogen-donating antioxidants converting into a colourless product. The applicability of the developed method was tested by measurement of the antioxidant activity of pure compounds as well as by analysing complex food and beverage samples. The antioxidant activity was presented as l(+) ascorbic acid equivalence. The values obtained by this methodology were not significantly different from the results obtained by the original spectrophotometric ABTS assay. For most of the studied antioxidants, antioxidant activity varied with pH and dilution. The proposed SIA system is suitable for screening direct or diluted total antioxidant activity of pure compounds or food samples.     

Rapid flow injection method for the determination of sulfite in wine using the permanganate-luminol luminescence system

A simple, rapid and sensitive chemiluminescence method for the determination of sulfite has been developed by combining flow-injection analysis and its sensitizing effect on the known chemiluminescence emission produced by the oxidation of luminol in alkaline medium; in this work permanganate has been proposed as oxidizing reactive. The optimum conditions for the chemiluminescence emission were established. The chemiluminescence was proportional to the sulfite concentration over the range 1.6 × 10⁻⁵ and 4.0 × 10⁻⁴ mol L⁻¹. The detection limit was 4.7 × 10⁻⁶ mol L⁻¹ of sulfite. The method has been satisfactorily used for the determination of free and bound sulfite in wines.     

Successive determination of urinary protein and glucose using spectrophotometric sequential injection method

A new sequential injection (SI) system with spectrophotometric detections has been developed for successive determination of protein and glucose. The protein assay is based on ion-association of protein with tetrabromophenolphthalein ethyl ester (TBPE) in the presence of Triton X-100 at pH 3.2. The blue product is monitored for absorbance at 607 nm. For glucose, hydrogen peroxide, generated by the oxidation of glucose in the presence of glucose oxidase immobilized on glass beads packed in a minicolumn, is monitored using iron-catalyzed oxidation reaction of p-anisidine to form a red colored product (520 nm). The SI procedure takes advantage in performing the protein assay during the incubation period for glucose oxidation. Linear ranges were up to 10 mg dL⁻¹ human serum albumin (HSA) with a limit of detection (LOD) (3σ) of 0.3 mg dL⁻¹, and up to 12.5 mg dL⁻¹ glucose with LOD of 0.08 mg dL⁻¹. R.S.D.s (n = 11) were 2.7% and 2.5% (for 1 mg dL⁻¹ and 5 mg dL⁻¹ HSA) and 1.4% (9 mg dL⁻¹ glucose). Sample throughput for the whole assay of both protein and glucose is 6 h⁻¹. The automated system has been demonstrated for the successive assay of protein and glucose in urine samples taken from diabetic disease patients, with good agreement with the other methods. This developed SI system is an alternative automation for screening for diabetic diagnosis.     

Selective stopped-flow sequential injection method for the spectrophotometric determination of titanium in dental implant and natural Moroccan phosphate rock

The present work reports the first sequential injection (SI) method for the spectrophotometric determination of Ti(IV). The method is based upon the reaction of Ti(IV) with chromotropic acid (CA) in acidic medium to form a water-soluble complex (λ_max = 420 nm). The chemical and instrumental variables of the system that affected the reaction were studied. Selectivity was greatly enhanced using ascorbic acid. A linear calibration graph was obtained in the range 0.2-10.0 mg l⁻¹ Ti(IV) at a sampling frequency of 24 h⁻¹. The precision was satisfactory (s_r = 1.5% at 5.0 mg l⁻¹ Ti(IV), n = 12) and the 3σ limit of detection, c_L, was 0.7 mg l⁻¹ (n = 10). The developed method proved to be adequately selective and was applied successfully to the analysis of real samples (dental implant and natural Moroccan phosphate rock) giving accurate results based on recovery studies (98-105%).     

High-sensitivity methods for sequential injection determination of the main constituents of alloys

A sequential injection system with spectrophotometric detection was proposed for the determination of copper, zinc and lead in brass. In view of the high analyte concentrations and the sensitivity of the involved catalytic methods, optimization of the flow system was carried out aiming mild reaction conditions. Copper and lead determinations were based on the catalytic effects of Cu²⁺ and Pb²⁺ on the oxidation rates of resorcinol and pyrogallol red by H₂O₂, respectively, and zinc determination involved precipitate formation after oxidation of 1-nafthylethylenediamine by K₃Fe(CN)₆. The analytical procedures were designed with some common parameters such as pH=9.0 (borate system), λ=530 nm, and H₂O₂ as oxidizing agent; system geometry was maintained.The proposed system is rugged, and base line drift is not observed during 4 h operation periods. Twenty samples are run per hour (60 determinations) and reagent consumption is minimal, thus avoiding drawbacks related to waste management. Precise results (R.S.D.<1.0%; n=7) are obtained and a detection limit of 1% (w/w) was estimated for the three analytes. Results were in agreement with flame atomic absorption spectrometry.     

Sequential injection method for the direct spectrophotometric determination of bismuth in pharmaceutical products

A spectrophotometric method is reported for the determination of bismuth in pharmaceutical products using sequential injection analysis. Methylthymol blue (MTB) was used as a color forming reagent and the absorbance of the Bi(III)-MTB complex was monitored at 548 nm. The various chemical and physical variables that affected the reaction were studied. A linear calibration graph was obtained in the range 0.0-75.0 mg l⁻¹ Bi(III) at a sampling frequency of 72 h⁻¹. The reagent consumption was considerably reduced compared to conventional flow injection systems, as only 150 μl of MTB were consumed per run. The precision was very satisfactory (s_r=0.5%, at 50.0 mg l⁻¹ Bi(III), n=12) and the limit of detection, c_L, was 0.250 mg l⁻¹. The developed method was applied successfully to the analysis of various pharmaceutical products containing Bi(III). The relative errors e_r, were <1.5% in all cases and were evaluated by comparison of the obtained results with those found using atomic absorption spectrometry as the reference method.     

Alternative method for measurement of albumin/creatinine ratio using spectrophotometric sequential injection analysis

A simple, automatic and practical system for successive determination of albumin and creatinine has been developed by combining sequential injection analysis (SIA) and highly sensitive dye-binding assays. Albumin detection was based on the increase in the absorbance due to complex formation between albumin and eosin Y in acidic media. The absorbance of the complex was monitored at 547 nm. For the creatinine assay, the concentration of creatinine was measured by reaction with alkaline picrate to form a colored product which absorbs at 500 nm. The influences of experimental variables such as effects of pH, reagent concentration, standard/sample volume and interferences were investigated. Under optimal conditions, the automated method showed linearity up to 20 mg L⁻¹ for albumin and 100 mg L⁻¹ for creatinine. The 3σ detection limits were 0.6 and 3.5 mg L⁻¹ for albumin and creatinine, respectively, and the relative standard deviations (n = 10) were 2.49% for 20 mg L⁻¹ albumin, and 3.14% for 20 mg L⁻¹ creatinine. Application of the proposed method to the direct analysis of urinary samples yielded results which agreed with those obtained from the Bradford protein assay and a creatinine enzymatic assay according to a paired t-test. The results obtained should be a step towards developing a fully automated and reliable analytical system for clinical research, which requires direct determination of albumin and creatinine and/or its ratios.     

Sequential injection spectrophotometric determination of iron as Fe(II) in multi-vitamin preparations using 1,10-phenanthroline as complexing agent

A sequential injection analysis (SIA) system is proposed for the determination of iron (II). Fe(II) was determined by SIA based on the reaction between 1,10-phenanthroline and iron (II), yielding an orange–red colour complex with absorption maximum at 512 nm. The method involved aspiration of 187 μl sample/standard zone followed by a zone of a reagent solution containing 140 μl of 7.8 × 10⁻⁴ mol l⁻¹ 1,10-phenanthroline into a carrier stream to be stacked inside a holding coil and flow reversed through a reaction coil to a detector. The optimum condition was evaluated and the calibration curve is linear over a range of 0.25 to 5.0 mg l⁻¹ of Fe(II) with detection limit of 18 μg l⁻¹. A sample throughput of 40 h⁻¹ was established. This technique is found to be simple, accurate, reproducible and sensitive. The proposed method was successfully applied for the determination of total iron as Fe(II) in pharmaceutical products (multi-vitamin tablets) and is especially useful for the determination of iron (II) in tablets with lower iron (II) contents. The results were found to be in good agreement with the results obtained by manual UV/Vis spectrophotometry and flame atomic absorption spectrometry (FAAS) and with claimed values by the manufacturers.     

Non-equilibrium determination of metoclopramide and tetracaine hydrochloride by sequential injection spectrophotometry

A new sequential injection spectrophotometric method was proposed for the determination of metoclopramide and tetracaine hydrochloride. The method was based on the detection of an unstable red intermediate compound resulting from the reaction of metoclopramide or tetracaine hydrochloride with potassium dichromate, in the presence of sodium oxalate, in sulfuric acid solution. The related reaction mechanisms of this new method have been studied. The experimental conditions were optimized for the stopped-flow and continuous-flow sequential injection models. For continuous flow, the linear range for determination of metoclopramide, the detection limit and the sampling frequency were 13-130 μg ml⁻¹, 9.4 μg ml⁻¹ and 40 samples per hour, respectively. For stopped flow, they were 3-42 μg ml⁻¹, 1.0 μg ml⁻¹ and 18 h⁻¹, respectively. Adopting the continuous-flow model for tetracaine hydrochloride, the linear range was 25-300 μg ml⁻¹, and the detection limit was 18.0 μg ml⁻¹ with sampling frequency of 40 h⁻¹. This method has been used to determine metoclopramide and tetracaine hydrochloride in pharmaceutical preparations, and the results are compared with those determined by the pharmacopoeia method. Statistical analysis reveals that there was no evidence of significant difference between the methods.     

Spectrophotometric determination of iron(III) and total iron by sequential injection analysis technique

A procedure for determination of concentrations of iron(III) and total iron by sequential injection analysis is described. The method is based on the strong blue-colored complexes formed between iron(III) and tiron. The absorbance of the complexes is measured spectrophotometrically at 635 nm. Oxidation of iron(II) and masking of interfering fluoride is simultaneously done by injecting one zone of hydrogen peroxide and one of thorium(IV) between the sample and reagent zones. Concentration of iron(III) and total iron, in the range 0.002–0.026 M, in diluted samples from a pickle bath were determined. The relative standard deviation was 0.4% (n=7). The method was also used in a pilot plant of a zinc process for determination of iron(III) in the range 0.2–3.0 g l⁻¹. The sample throughput is approximately 17 samples per hour, including three repetitive determinations of each sample.     

Reversed flow injection and sandwich sequential injection methods for the spectrophotometric determination of copper(II) with cuprizone

Two new flow methods, flow injection analysis (FIA) and sequential injection analysis (SIA), for the spectrophotometric determination of Cu(II) in water at trace levels have been developed and optimised. Both methods are based on the reaction with oxalic acid bis(cyclohexylidene hydrazide) (cuprizone) in alkaline media. The two procedures have been developed for the final aim to compare their performances and to offer new rapid heavy metals analysis tools, avoiding the use of extraction steps. A detailed study of the physico-chemical parameters affecting the systems performances has been carried out. The reversed FIA and sandwich SIA approaches offered the best sensitivity. In both cases, an extremely good linearity has been obtained within the range 0.06-4 μg ml⁻¹ (correlation coefficient r=0.9999), whereas the observed detection limits were 0.013 and 0.004 μg ml⁻¹, for FIA and SIA, respectively. Furthermore, due to the great similarity of the diffusion zones in the reaction slugs, our approach offers the opportunity to compare the two methods in analogous conditions. This SIA method, besides keeping its typical reagent saving features, offered analytical performances equivalent to those of FIA. To obtain these results, an original “stop-flow like” method was successfully employed in the SIA approach. Both methods were validated by analysis of real water samples, after copper addition, and certified reference samples of fortified and waste waters.     

固相萃取-顺序注射分光光度法快速测定微生物菌落中的麦白霉素

在顺序注射系统中引入C18固相萃取柱进行生米卡链霉菌菌落样品的纯化富集,建立了快速测定菌落中麦白霉素的分光光度法。用超声波破碎菌落细胞后,将样品溶液通过固相萃取柱,用少量甲醇洗脱吸附在C18微珠上的麦白霉素,232 nm检测。进样量为2 ml,洗脱液体积为100μL,麦白霉素的富集倍率为14;线性范围为0.1~10μg/mL,检出限为0.02μg/mL,RSD为2.5%(0.5μg/mL,n=7)。菌落样品中麦白霉素的加标回收率为96%~100%。     

Development of a flow method for the determination of phosphate in estuarine and freshwaters—Comparison of flow cells in spectrophotometric sequential injection analysis

A sequential injection system with dual analytical line was developed and applied in the comparison of two different detection systems viz; a conventional spectrophotometer with a commercial flow cell, and a multi-reflective flow cell coupled with a photometric detector under the same experimental conditions. The study was based on the spectrophotometric determination of phosphate using the molybdenum-blue chemistry. The two alternative flow cells were compared in terms of their response to variation of sample salinity, susceptibility to interferences and to refractive index changes. The developed method was applied to the determination of phosphate in natural waters (estuarine, river, well and ground waters). The achieved detection limit (0.007 μM PO₄³⁻) is consistent with the requirement of the target water samples, and a wide quantification range (0.024–9.5 μM) was achieved using both detection systems.     

顺序注射催化动力学光度法测定织物和室内空气中痕量甲醛

在磷酸介质中 ,甲醛可以催化溴酸钾氧化　花青的反应使其退色 ,据此建立了顺序注射催化动力学光度法测定织物和室内空气中痕量甲醛的新方法。方法的线性范围 0 .5～ 7.0 μg mL ,检出限 0 .1 μg mL。用于树脂整理特殊织物和室内空气中痕量甲醛的测定 ,回收率在 97.0 %～ 1 0 5 .0 %之间。     

流动注射褪色光度法测定食品中的亚硫酸盐

基于亚硫酸盐在碱性条件下与碱性品红的褪色反应,建立了流动注射光度分析测定食品中亚硫酸盐的新方法.在38样/h采样频率下检出限为0.016μg/mL,SO32-质量浓度在0.04～1.5 μg/mL范围符合朗伯比耳定律,测定1.2μg/mL SO32- 11次,相对标准偏差为0.41%.该法可用于食品中亚硫酸盐的测定.