Simultaneous, sensitive and selective on-line chemiluminescence determination of Cr(III) and Cr(VI) by capillary electrophoresis

A novel in-capillary reduction and capillary electrophoretic (CE)-chemiluminescence (CL) method was developed for the sensitive and selective determination of chromium(III) and chromium(VI). The proposed method was based on the in-capillary reduction of Cr(VI) with acidic H₂O₂ to form Cr(III) using the zone-passing technique and chemiluminescence detection of Cr(III). The sample [Cr³⁺ and CrO₄²⁻], hydrochloric acid, and H₂O₂ (reductant) solution segments were injected for specified periods of time in this order from the anodic end of a capillary, followed by application of an appropriate running voltage between both ends. As both chromium species have opposite charges, Cr³⁺ migrates to the cathode while CrO₄²⁻ ion, moving oppositely to the anode, reacts with acidic H₂O_2, resulted in formation of Cr³⁺. Based on the migration time difference of both Cr³⁺ ions, they were separated by zone electrophoresis. Running buffer was composed of 0.02 mol l⁻¹ HAc-NaAc (pH 4.7) with 1×10⁻³ mol l⁻¹ EDTA. Parameters affecting CE-CL separation and detection, such as reductant concentration, mixing mode of the analytes with CL reagent, CL reaction reagent pH and concentration, stability of luminol-hydrogen peroxide mixed solution were optimized. The limits of detection for chromium(III) and chromium(VI) (3σ) were 6×10⁻¹³ mol l⁻¹ (mass concentration 12 zmol) and 8×10⁻¹² mol l⁻¹ (160 zmol), respectively. This method offered potential advantages of simplicity, sensitivity, selectivity and applicability to the determination of Cr(III) and Cr(VI) in environmental water.     

A novel dichromate-sensitive fluorescent nano-chemosensor using new functionalized SBA-15

A novel fluorescence nano-chemosensor for Cr₂O₇²⁻ anion has been developed by assembly of fluorescent aluminum complex of 8-hydroxyquinoline (AlQ_x) within the channels of modified SBA-15. SBA-SPS-AlQ_x shows a fluorescence emission at 486 nm. The observed remarkable fluorescence of SBA-SPS-AlQ_x quenches in presence of Cr₂O₇²⁻ anion. The results showed that this fluorescent nano-material can be a useful chemo-sensor for determination of dichromate anions in aqueous solutions. The linear detecting range of fluorescent nano-chemosensor for Cr₂O₇²⁻ anion was 0.16–2.9 μmol L⁻¹. The lowest limit of detection (LDL) was also found to be 0.2 ng mL⁻¹ in aqueous solutions. SBA-SPS-AlQ_x showed selectively and sensitively fluorescent quenching response toward Cr₂O₇²⁻ ion in comparison with I₃⁻, NO₃⁻, CN⁻, CO₃²⁻, Br⁻, Cl⁻, F⁻, H₂PO₄⁻ and SO₄²⁻ ions, which was because of the higher stability of its inorganic complex with dichromate ion.     

Chromium retention properties of N-alkyl quaternized poly(4-vinylpyridine)

The ability of solid N-alkyl quaternized poly(4-vinylpyridine) with hexyl, octyl and decyl bromide for the retention of chromate and dichromate forms of Cr(VI) in aqueous solutions is studied. The retention of Cr(VI) was investigated by batch equilibrium procedure and this study was supported by UV-vis spectrophotometry, infrared (IR) spectroscopy and thermal analysis (glass transition temperature and thermal degradation). The retention of Cr(VI) was possible in the range of concentrations between 1 × 10⁻⁶ and 1 × 10⁻³ mol/L and it was dependent on the length of the polyelectrolyte side aliphatic chain. Thermogravimetric analysis (TGA) indicated that solid phase, (N-alkyl quaternized poly(4-vinylpyridine), with Cr(VI) (P4VPyC8-Cr(VI)) is slightly more stable than P4VPyC8 in absence of Cr(VI). Differential scanning calorimetric (DSC) measurements indicate that the segmental movements are restricted due to the presence of chromate and/or dichromate ions in the solid phase.     

Structural characterization and catalytic properties of bis(1,1,3,3-tetramethylguanidinium) dichromate

The structure of bis(1,1,3,3-tetramethylguanidinium) dichromate was determined from powder X-ray diffraction data. The compound crystallizes in the monoclinic system (space group P2₁/n) with a = 10.79714 (15) Å, b = 11.75844 (16) Å, c = 8.15097 (11) Å, β = 109.5248 (6)°. The structure consists of dichromate anions (Cr₂O₇²⁻) stabilized by tetramethylguanidinium cations ([H₂NC(N(CH₃)₂)₂]⁺ or [TMGH]⁺). Phase transitions of [TMGH]₂Cr₂O₇ were determined by differential scanning calorimetry, thermal gravimetric analysis and in situ Raman spectroscopy, where the decomposition of the matrix into CrO_x was found at 171-172 °C. Further heat treatment to above 400 °C resulted in formation of the thermodynamically stable Cr₂O₃, most likely with the [TMGH]⁺ cation as reductant. The catalytic activity of [TMGH]₂Cr₂O₇ supported on TiO₂ anatase in the selective catalytic reduction (SCR) of nitrogen oxide was also investigated, however only moderate activity was observed in the temperature range 100-400 °C compared to the activity of e.g., vanadia supported on titania.     

Dichromate dosimetry: The effect of acetic acid on the radiolytic reduction yield

The radiation chemical yield for the reduction of dichromate, Cr(VI) → Cr³⁺, in an acidic aqueous perchloric acid solution of potassium dichromate, may be increased from 0.04 to >0.2 μ mol J^-1 by adding acetic acid. The increased yield, G[-(Cr₂O₇)^2-] is about the same in N_2- and O₂-saturated solutions. The molar linear absorption coefficient at 350 nm also is the same in both solutions (ϵ_m = 2800 M^-1cm^-1) at pH 0.4. The proposed mechanism to explain the enhanced response in N₂-saturated solutions involves the efficient reaction of acetic acid with hydroxyl radicals by the abstraction of H from the methyl group; the resulting acid radicals react with relatively high yield to reduce Cr(VI). In O₂-saturated solution, the acetic acid radical apparently goes through an acetic acid peroxyl radical by a bimolecular reaction to the tetroxide intermediate of acetic acid, which releases H₂O₂ with relatively high yield by a Bennett-type reaction. This additional H₂O₂, as a reducing agent, reacts slowly with dichromate and boosts the value of G[-(Cr₂O₇)^2-]. The negative slope of the response (ΔA vs dose) continues to increase during the period immediately after irradiation of oxygenated solution, due to slow reaction of radiolytically-produced H₂O₂ with dichromate. There is also in both O₂- and N₂-saturated solution a long-term slow reaction involving oxidation of the organic substrate (in this case, acetic acid). Because of these instabilities, the solutions cannot readily be used for dosimetry without the presence of silver ions, which in the oxidized state, Ag²⁺, act to stabilize the solution after irradiation. The addition of silver dichromate at a concentration of 0.1 mM decreases the yield to G[-(Cr₂O₇)^2-] = 0.17 μmolJ^-1, but greatly improves the stability of the solution after irradiation. The absorbed dose range for the modified dichromate dosimeter when analyzed spectrophotometrically at 350 nm wavelength is approx. 2 × 10²-2 × 10³ Gy.     

A novel kinetic determination of dissolved chromium species in natural and industrial waste water

A highly sensitive, selective and simple kinetic method was developed for the determination of dissolved chromium species based on the catalytic effect of Cr(III) and/or Cr(VI) on the oxidation of 2-amino-5-methylphenol (AMP) with H₂O₂. The fixed time and initial rate variants were used for kinetic spectrophotometric measurements by tracing the oxidized product at 400 nm for 10 min after starting the reaction. Boric acid and Tween-40 exerted pronounced activating and micellar sensitizing effects on the studied redox reaction, respectively. The optimum reaction conditions were: 3.0 mmol l⁻¹ AMP, 0.45 mol l⁻¹ H₂O₂, 0.50 mol l⁻¹ boric acid, 4 v/v% Tween-40, 10 mmol l⁻¹ phosphate buffer and pH 6.45 ± 0.02 at 35 °C. Both Cr(III) and Cr(VI) ions exerted the same catalytic effect on the studied reaction. Linear calibration graphs were obtained for the determination of up to 6.0 ng ml⁻¹ Cr with detection limits of 0.054 and 0.10 ng ml⁻¹ Cr; following the fixed time and initial rate methods, respectively. The proposed method was successfully applied to the speciation and determination of trace levels of dissolved Cr(III) and Cr(VI) in natural and effluents of industrial waste water. The total dissolved Cr(III) and Cr(VI) species was determined first. In a second run, Cr(VI) was determined alone after precipitation of Cr(III) ions in presence of Al(OH)₃ collector, where Cr(III) is then determined by difference. Moreover, published catalytic-spectrophotometric methods for chromium determination were reviewed.     

Flow injection direct spectrophotometric assay for the speciation of trace chromium(III) and chromium(VI) using chromotropic acid as chromogenic reagent

A new rapid and sensitive FI assay is reported for the simultaneous direct spectrophotometric determination of trace Cr(VI) and Cr(III) in real samples. The method is based upon the reaction of Cr(VI) with chromotropic acid (CA) in highly acidic medium to form a water-soluble complex (λ_max = 370 nm). Cr(III) reacts with CA only after its on-line oxidation to Cr(VI) by alkaline KIO₄. The determination of each chromium species in the sample was achieved by absorbance differences. The calibration curves were linear over the range 3-4000 μg l⁻¹ and 30-1200 μg l⁻¹ for Cr(VI) and Cr(III), respectively, while the precision close to the quantitation limit was satisfactory in both cases (s_r = 3.0% for Cr(VI) and 4.0% for Cr(III) (n = 10) at 10 and 50 μg l⁻¹ level, respectively). The method developed proved to be adequately selective and sensitive (c_L = 1 and 10 μg l⁻¹ for Cr(VI) and Cr(III), respectively). The application of the method to the analysis of water samples (tap and mineral water) gave accurate results based on recovery studies (93-106%). Analytical results of real sample analysis were in good agreement with certified values.     

Simultaneous determination of Cr(III) and Cr(VI) with prechelation of Cr(III) using phthalate by ion interaction chromatography with a C-18 column

Ion interaction chromatography has been successfully used for the simultaneous determination of Cr(III) and Cr(VI) in waste water. A C-18 column which had been dynamically coated with octylamine was used for the separation of Cr(III) and Cr(VI) based on anionic interaction. Cr(III) was chelated with potassium hydrogen phthalate (KHP) before injecting into the column since the Cr(III) did not exist in an anionic form like the Cr(VI) (Cr₂O₇²⁻) presented at the optimum condition. The analytes were detected at 200 nm and linear relationship between absorption with the concentration of Cr(III) or Cr(VI) was 0.1-50 mg/L. Most of the interested interferences including alkali metals, heavy metals and organic materials have no significant effect on Cr(III)-KHP complexation and Cr(VI) stability, only NH₄⁺ and ascorbic acid yielded the serious effect on the Cr(VI) stability. The relative standard deviations calculated from both of peak area and retention time were 0.75-2.20%. The sensitivity of the method at the level concentration of sub mg/L enabled the simultaneous determination of Cr(III) and Cr(VI) contents in waste water samples without any special sample preparation step.     

Sensitive assay for oxygen solubility in molten alkali metal carbonates by indirect flame atomic absorption spectrometric Cr(VI) determination

A precise and accurate indirect analytical method for the assessment of O₂ solubility in molten (Li_0.62K_0.38)₂CO₃ and (Li_0.52Na_0.48)₂CO₃ is described. The method is based on the oxidation of Cr₂(SO₄)₃ (added in excess to the melt) by the oxygenate species, which are formed inside the melt when it is in contact with oxygen gas, and subsequent determination of trace amount of Cr(VI) in withdrawn frozen melts by flame atomic absorption spectrometry (FAAS). The samples (1.0-2.0 g) are dissolved in dilute hydrochloric acid at room temperature. The speciation of Cr(VI) is carried out by complexation with ammonium pyrrolidine dithiocarbamate (APDC), followed by extraction into methyl isobutyl ketone (MIBK), which is introduced directly into the flame. Optimisation of the flame composition provided maximum Cr signal in organic phase under lean acetylene-air flame. The separation and preconcentration parameters such as sample volume/extractant volume ratio, pH sample solution, chelating concentration and extraction time are evaluated. Under the optimised conditions Cr(VI) is efficiently separated from Cr(III), which exceeded 200-folds. The results of the analysis of synthetic samples using standards in MIBK medium give rise to recoveries of 98-99%. The Cr(VI) detection limit of 4×10⁻⁶ g L⁻¹ using 12.5-fold preconcentration and relative standard deviation of 1% at the 0.10 mg L⁻¹ level are obtained. The sampling-to-sampling reproducibility was typically 3-5% relative standard deviation. By changing the preconcentration factor and the dilution of the sample melt, it is possible to analyse oxygen concentrations in molten alkali metal carbonates as low as 1.5×10⁻⁹ mol O₂ per gram melt.     

Speciation of chromium in Australian fly ash

The concentrations of chromium (III) and (VI) in fly ash from nine Australian coal fired power stations were determined. Cr(VI) was completely leached by extraction with 0.01 M NaOH solution and the concentration was determined by inductively coupled plasma atomic emission spectrometry (ICP-AES). This was confirmed by determining Cr(III) and Cr(VI) in the extracts of fly ash that had been spiked with chromium salts. These analytical measurements were done using a combination of ion-exchange chromatography and ICP-AES. The elutant was 0.05 M HNO₃ containing 0.5%-CH₃OH. When the column was operated at a flow rate of 1.2 ml min⁻¹ and samples were injected by use of a sample loop with a volume of 100 μl, Cr(III) and Cr(VI) in sample solution was exclusively separated within approximately 10 min. The detection limits (3σ) were 5 ng for Cr(III) (0.050 mg l⁻¹) and 9 ng for Cr(VI) (0.090 mg l⁻¹), respectively. A relative standard deviation of 1.9% (n = 6) was obtained for the determination by IC-ICP-AES of 0.25 mg l⁻¹ Cr(III) and Cr(VI).     

Electrochemical behavior of hexafluoroniobate, heptafluorotungstate, and oxotetrafluorovanadate anions in N-butyl-N-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide room temperature ionic liquid

Electrochemical behavior of hexafluoroniobate (Nb(V)F₆⁻), heptafluorotungstate (W(VI)F₇⁻), and oxotetrafluorovanadate (V(V)OF₄⁻) anions has been investigated in N-butyl-N-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide (BMPyrTFSA) ionic liquid at 298 K by means of cyclic voltammetry and chronoamperometry. Cyclic voltammograms at a Pt electrode showed that Nb(V)F₆⁻ anion is reduced to Nb(IV)F₆²⁻ by a one-electron reversible reaction. Electrochemical reductions of W(VI)F₇⁻ and V(V)OF₄⁻ anions at a Pt electrode are quasi-reversible and irreversible reactions, respectively, according to cyclic voltammetry. The diffusion coefficients of Nb(V)F₆⁻, W(VI)F₇⁻ and V(V)OF₄⁻ determined by chronoamperometry are 1.34 × 10⁻⁷, 7.45 × 10⁻⁸ and 2.49 × 10⁻⁷ cm² s⁻¹, respectively. The Stokes radii of Nb(V)F₆⁻, W(VI)F₇⁻, and V(V)OF₄⁻ in BMPyrTFSA have been calculated to be 0.23, 0.38, and 0.12 nm, from the diffusion coefficients and viscosities obtained.     

Determination of Cr(VI) with Selective Sensing of Cr(VI) Anions by a PVC‐Membrane Electrode Based on Quinaldine Red

A dichromate‐selective PVC‐membrane electrode based on Quinaldine Red (an acridinium derivative) is described. The electrode exhibits rapid (< 30 s) and linear response to the activity of Cr(VI) anions in the range of 5.2 × 10^?6 ?1.0 × 10^?1 M dichromate with the limit of detection 2.5 × 10^?6 Mof Cr₂O₇^2?. The sensor is used as an indicator electrode in potentiometric determination of Cr(VI) anions and is also suitable for end‐point indication in the titrations of proper metal ions with dichromate under laboratory conditions. The proposed electrode has been applied to the direct potentiometric determination of Cr(VI) anions in water samples with satisfactory results.     

Modified mesoporous silica materials for on-line separation and preconcentration of hexavalent chromium using a microcolumn coupled with flame atomic absorption spectrometry

A modified SBA-15 mesoporous silica material NH₂-SBA-15 was synthesized successfully by grafting γ-aminopropyl-triethoxysilane. The material was characterized using transmission electron microscopy (TEM) and Fourier transform infrared/Raman (FT-IR/Raman) spectroscopy, and used for the first time in a flow injection on-line solid phase extraction (SPE) coupled with flame atomic absorption spectrometry (FAAS) to detect trace Cr (VI). Effective sorption of Cr (VI) was achieved at pH 2.0 with no interference from Cr (III) and other ions and 0.5 mol L⁻¹ NH₃·H₂O solution was found optimal for the complete elution of Cr (VI). An enrichment factor of 44 and was achieved under optimized experimental conditions at a sample loading of 2.0 mL min⁻¹ sample loading (300 s) and an elution flow rate of 2.0 mL min⁻¹ (24 s). The precision of the 11 replicate Cr (VI) measurements was 2.1% at the 100 μg L⁻¹ level with a detection limit of 0.2 μg L⁻¹ (3 s, n = 10) using the FAAS. The developed method was successfully applied to trace chromium determination in waste water. The accuracy was validated using a certified reference material of riverine water (GBW08607).     

Bidentate reagents form cyclic organic-Cr(VI) molecules for aiding in the removal of Cr(VI) from water: density functional theory and experimental results

Hexavalent chromium, Cr(VI), in the form of chromate (CrO₄ ^2?) or dichromate (Cr₂O₇ ^2?) is a well-described carcinogen found in the drinking water in many parts of the country at levels deemed unsafe by the U.S. Environmental Protection Agency and the World Health Organization. We report on the ability of bidentate organic molecules containing diols or diamines to capture chromate ions from aqueous sources by forming cyclic organic-Cr(VI) carbonates or ureas. After their formation, the cyclic organic-Cr(VI) molecules are readily absorbed onto granulated activated charcoal to facilitate Cr(VI) removal. Using density functional theory, E ₀ values for the reactions of diols and diamines with chromate were calculated and correlated with the experimental findings of Cr(VI) removal.     

Speciation of chromium in natural waters by micropumping multicommutated light emitting diode photometry

A simple and sensitive multicommutated flow procedure, implemented by employing a homemade light emitting diode (LED) based photometer, has been developed for the determination of chromium (VI) and total chromium in water. The flow system comprised a set of four solenoid micro-pumps, which were assembled to work as fluid propelling and as commutating devices. The core of the detection unit comprised a green LED source, a photodiode and a homemade flow cell of 100 mm length and 2 mm inner diameter. The photometric procedure for the speciation of chromium in natural waters was based on the reaction of Cr (VI) with 1,5-diphenylcarbazide. Cr (III) was previously oxidized to Cr (VI) and determined as the difference between total Cr and Cr (VI). After carrying out the assays to select the best operational conditions the features of the method included: a linear response ranging from 10 to 200 μg l⁻¹ Cr (III) and Cr (VI) (r = 0.999, n = 7); limits of detection of 2.05 and 1.0 μg l⁻¹ for Cr (III) and Cr (VI), respectively; a relative standard deviation lower than 2.0% (n = 20) for a typical solution containing 50 μg l⁻¹ Cr; a sampling throughput of 67 and 105 determinations per hour for total Cr and Cr (VI), respectively, and recovery values within the range of 93-108% for spiked concentrations of the order of 50 μg l⁻¹.     

On-line preconcentration and speciation analysis of Cr(III) and Cr(VI) using baker's yeast cells immobilised on controlled pore glass

A study was undertaken to evaluate Saccharomyces cerevisiae as a substrate for the biosorption of Cr(III) and Cr(VI) aiming to the selective determination of these species in aqueous solutions. The yeast cells were covalently immobilised on controlled pore glass (CPG), packed in a minicolumn and incorporated in an on-line flow injection system. The effect of chemical and physical variables affecting the biosorption process was tested in order to select the optimal analytical conditions for the Cr retention by S. cerevisiae. Cr(III) was retained by the immobilised cells and Cr(VI) were retained by CPG. The speciation was possible by selective and sequential elution of Cr(III) with 0.05 mol L⁻¹ HCl and 2.0 mol L⁻¹ HNO₃ for Cr(VI). The influence of some concomitant ions up to 20 mg L⁻¹ was also tested. Quantitative determinations of Cr were carried out by means of inductively coupled plasma optical emission spectrometry (ICP OES). Preconcentration factors of 12 were achieved for Cr(III) and 5 for Cr(VI) when 1.7 mL of sample were processed reaching detection limits of 0.45 for Cr(III) and 1.5 μg L⁻¹ for Cr(VI). The speciation of inorganic Cr in different kinds of natural waters was performed following the proposed method. Spiked water samples were also analysed and the recoveries were in all cases between 81 and 103%.     

Determination of chemical oxygen demand values by a photocatalytic oxidation method using nano-TiO2 film on quartz

A COD measurement by a photocatalytic oxidation method using nano-TiO₂ film was investigated. K₂Cr₂O₇ was added into the solution to enhance the efficiency of photocatalytic degradation, and simultaneously K₂Cr₂O₇ was reduced to Cr(III) by photogenerated electrons, which were adsorbed on the surface of TiO₂. The measuring principle was based on direct determination of Cr(III) concentration which was proportional to the COD value. Under the optimized experiment condition, the application range was 20-500 mg l⁻¹, and the detection limit was 20 mg l⁻¹. The immobilization of photocatalyst on the supports could not only solve the problem of low recovery of the catalyst and hard separation from the solution, but also overcome its shortcoming of poor stability. Applied this method to the determination of real samples, it was found to be rapid and environmentally friendly. Additionally, the method proposed above for determination of COD was in excellent correspondence with values obtained by using the conventional method.     

Mechanism study on inorganic oxidants induced inhibition of Ru(bpy)₃²+ electrochemiluminescence and its application for sensitive determination of some inorganic oxidants

Inhibited Ru(bpy)₃²⁺ electrochemiluminescence by inorganic oxidants is investigated. Results showed that a number of inorganic oxidants can quench the ECL of Ru(bpy)₃²⁺/tri-n-propylamine (TPrA) system, and the logarithm of the decrease in ECL intensity (ΔI) was proportional to the logarithm of analyte concentrations. Based on which, a sensitive approach for detection of these inorganic oxidants was established, e.g. the log-log plots of ΔI versus the concentration of MnO₄⁻, Cr₂O₇²⁻ and Fe(CN)₆³⁻ are linear in the range of 1 × 10⁻⁷ to 3 × 10⁻⁴ M for MnO₄⁻ and Cr₂O₇²⁻, and 1 × 10⁻⁷ to 1 × 10⁻⁴ M for Fe(CN)₆³⁻, with the limit of detection (LOD) of 8.0 × 10⁻⁸ M, 2 × 10⁻⁸ M, and 1 × 10⁻⁸ M, respectively. A series of experiments such as a comparison of the inhibitory effect of different compounds on Ru(bpy)₃²⁺/TPrA ECL, ECL emission spectra, UV-Vis absorption spectra etc. were investigated in order to discover how these inorganic analytes quench the ECL of Ru(bpy)₃²⁺/TPrA system. A mechanism based on consumption of TPrA intermediate (TPrA^·) by inorganic oxidants was proposed.     

Synthesis,structure, optical and magnetic properties of [CrL(X)3], {L = 4′-(2-pyridyl)-2,2′:6′,2″-terpyridine; X = Cl,N3, NCS}

Three complexes of composition [CrL(X)₃], where L = 4′-(2-pyridyl)-2,2′:6′,2″-terpyridine and X = Cl⁻, N₃⁻, NCS⁻ are synthesized. They are characterized by IR, UV–Vis, fluorescence, EPR spectroscopic, and X-ray crystallographic studies. Structural studies reveal that the Cr(III) ion is coordinated by three N atoms of L in a meridional fashion. The three anions occupy the other three coordination sites completing the mer-N₃Cl₃ (1) and mer-N₃N₃ (2 and 3), distorted octahedral geometry. The Cr–N2 has a shorter length than the Cr–N1 and Cr–N3 distances and the order Cr–N(NCS⁻) < Cr–N(N₃⁻) < Cr–Cl is observed. They exhibit some of the d–d transitions in the visible and intra-ligand transitions in the UV regions. The lowest energy d–d transition follows the trend [CrLCl₃] < [CrL(N₃)₃] < [CrL(NCS)₃] consistent with the spectrochemical series. In DMF, they exhibit fluorescence having π → π^∗ character. All the complexes show a rhombic splitting as well as zero-field splitting (zfs) in X-band EPR spectra at 77 K.     

Light induced magnetic properties of spiropyrane tris(oxalato)chromate (III) single crystals

The effect of UV light on Weiss temperature and ESR spectra in 1-isopropyl-3, 3, 5′, 6′-tetramethylspiro[indolin-2,2′-[2H]pyrano[3,2-b]pyridinium] tris(oxalato)chromate (III) (Sp₃Cr(C₂O₄)₃) has been found. Additional line has been observed in the ESR spectra of irradiated samples in “strong” magnetic fields of ~15 kOe. The analysis of angular dependences of the ESR spectra allowed a contribution of Cr³⁺ ions to magnetic properties of Sp₃Cr(C₂O₄)₃ to be determined. The zero-field splitting parameters D=0.619 cm⁻¹, E=0.024 cm⁻¹ were derived from the experimental data. The parameters were typical for Cr³⁺ in the chromium oxalate. Weiss temperature changed sign from 25 to −25 K under UV irradiation. The value of Weiss temperature and its changing cannot be explained by exchange interaction, dipole-dipole interaction or the effect of crystal field. The existence of Weiss temperature is explained by the changes in amount and spin of paramagnetic particles. The change is due to thermoactivated redistribution of electrons between chromium ions and spiropyrane molecules. Light-induced transfer of electrons is also explaining the change in sign of Weiss temperature under UV irradiation.