Determination of water-soluble inorganic and organic species in atmospheric fine particulate matter

The use of ion chromatography (IC) in conjunction with ultrasonic extraction is described for the routine analysis of water-soluble major inorganic ions and organic acids in atmospheric fine particles (PM_2.5). Both the extraction method and the IC analysis were validated using NIST SRM 1648 (urban particulate matter). In addition, the reliability of the IC method was established by intercomparison of results obtained with those from suitable alternative analytical techniques (atomic absorption spectrometry (AAS), proton-induced X-ray emission (PIXE) spectrometry, and UV-Visible spectrophotometry). The validated IC method was successfully applied for field monitoring of PM_2.5 particles collected in Singapore over an extended period of time. The IC analysis revealed that the concentrations of individual ions were in the order, SO₄²⁻ > NH₄⁺ > NO₃⁻ > Na⁺ > K⁺ > Cl⁻, respectively. Among the major ionic components, SO₄²⁻ contributed 50% to the measured water-soluble aerosol mass followed by NH₄⁺ (16.5%) and NO₃⁻ (9.0%). The cations Na⁺, K⁺, Mg²⁺, and Ca²⁺ accounted for 24% of the total water-soluble mass. The IC analysis was performed to quantify the organic acids, which typically account for a small fraction of water-soluble organic compounds in PM_2.5. Oxalate was found to be the dominant species among the organic acids measured in this work.     

Chemical analysis of sulfur species in geothermal waters

Analytical methods have been developed to determine sulfur species concentrations in natural geothermal waters using Reagent-Free™ Ion Chromatography (RF™-IC), titrations and spectrophotometry. The sulfur species include SO₄²⁻, S₂O₃²⁻, and ∑S²⁻ with additional determination of SO₃²⁻ and S_xO₆²⁻ that remains somewhat semiquantitative. The observed workable limits of detections were ≤0.5 μM depending on sample matrix and the analytical detection limits were 0.1 μM. Due to changes in sulfur species concentrations upon storage, on-site analyses of natural water samples were preferred. Alternatively, the samples may be stabilized on resin for later elution and analysis in the laboratory. The analytical method further allowed simultaneous determination of other anions including F⁻, Cl⁻, dissolved inorganic carbon (DIC) and NO₃⁻ without sample preservation or stabilization. The power of the newly developed methods relies in routine analysis of sulfur speciation of importance in natural waters using techniques and facilities available in most laboratories doing water sample analysis. The new methods were successfully applied for the determination of sulfur species concentrations in samples of natural and synthetic waters.     

Chemical speciation of chromium(III,VI) employing extractive spectrophotometry and tetraphenylarsonium chloride or tetraphenylphosphonium bromide as ion-pair reagent

A simple and accurate extractive spectrophotometric procedure for the chemical speciation of chromium(III,VI) species in aqueous media has been developed. The method is based upon the extraction of the complex ion-associate formed between the chloro chromate (CrO₃Cl⁻) anion and the ion-pair reagent tetraphenylarsonium chloride (TPAs⁺Cl⁻) or tetraphenylphosphonium bromide (TPP⁺Br⁻) at pH ≤ 0 in chloroform followed by direct spectrophotometric measurement at 355 nm. The optimum concentration range evaluated by Beer-Lambert's law, Ringbom's plot, the molar absorptivity, the Sandell's sensitivity, the extraction and stability constants (K_D, K_ex and β), the stoichiometry and the extraction equilibria of the produced complex ion-associates have been determined and gave a convenient applications of the investigated system for analytical purposes. Chromium(III) was also determined by the proposed procedure after prior oxidation to chromate with H₂O₂ in alkaline solution. The method has been applied successfully for the analysis of chromium(VI) and total chromium(III,VI) in industrial wastewater of electroplating plant.     

Determination of water-soluble and insoluble compounds in size classified airborne particulate matter

The elemental composition of water soluble and acid soluble size-fractionated airborne particulate matter (APM) was investigated. PM2.5 and PM2.5-10 samples were collected every three days from October 2006 to October 2007 in Buenos Aires, Argentina. The collection was performed on Nucleopore® filters using a GENT sampler. Samples containing fine and coarse particles were subjected to an aqueous leaching to obtain information on the dissolution behaviors of ions, metal and metalloids. Key elements namely, Al, Ba, Ca, Cr, Cu, Fe, Mg, Mn, Pb, Se, Ti and Zn were determined in each fraction by inductively coupled plasma optical emission spectrometry (ICP OES). In the aqueous fractions, Cl⁻, SO₄²⁻, Na⁺ and NH₄⁺ were determined by high performance liquid chromatography (HPLC). A (6:2:5) mixture of nitric, hydrochloric and perchloric acids was used for leaching metals from the residual filters. For validation of the extraction procedure, the ICP OES measurements the Standard Reference Material NIST 1648 (Urban particulate matter) was subjected to the same analytical procedure that the samples loaded with APM. Total analyte concentration varied from 333.2 μg g^− 1 (equivalent to 3.7 ng m^− 3) for Ti to 692 mg g^− 1 (equivalent to 2.47 μg m^− 3) for Ca.     

Determination of metals, metalloids and non-volatile ions in airborne particulate matter by a new two-step sequential leaching procedure Part A: Experimental design and optimisation

The optimisation of a micro-analytical two-step sequential leaching procedure for the determination of non-volatile ions (NO₃⁻, SO₄²⁻, Cl⁻, Na⁺, Mg²⁺, NH₄⁺ and Ca²⁺) and of 17 elements (Al, As, Cd, Cr, Cu, Fe, Mg, Mn, Ni, Pb, S, Se, V, Zn, Sb, Si and Ti) in two fractions—extract and residue—on the same sample of air particulate matter is described. The two-step method was tested on the SRM NIST 1648 for equivalence with two reference methods, the EMEP procedure for ions extraction and the EN 12341 standard for the elemental determination of the PM₁₀ and is suitable for application to small sample amounts (less than 1 mg of particulate matter is needed), i.e. those collected by daily low volume filter-sampling. Performance times of the procedure were optimised to meet the target of routine application for large scale monitoring samples. A single ultrasonic-assisted extraction of air particulate matter is performed in 0.01 M acetate buffer at pH 4.5, followed by IC ions analysis and ICP-OES elemental analysis of the extract and by ICP-OES elemental analysis of the mineralized residue after dissolution by microwave-assisted digestion with a HNO₃/H₂O₂ mixture. Using a pH buffered extracting solvent was preferred to water or diluted acid solutions to improve the reproducibility of metals extraction with respect to existing leaching methods; the influence of pH, nature and concentration of the buffer solution and extraction time on analytes concentration in the extract is discussed. Values of ions extraction and elements recoveries resulted fairly equivalent with those obtained by the reference methods. The study was also extended to some non-certified elements (Mg, S, Sb, Si and Ti) for their environmental significance. Elements recoveries were obtained as sum of the extract and residue fractions and were comparable with those obtained by direct dissolution. Standard deviations were within 10% for almost all detected ions and elements.     

Uncertainty estimation of anions and cations measured by ion chromatography in fine urban ambient particles (PM2.5)

The present work presents a measurement uncertainty evaluation according to Guide to the Expression of Uncertainty in Measurement (GUM) of the concentration of the cations K⁺ and Li⁺ and anions NO₃⁻² and SO₄⁻² in fine airborne particulate matter, refers to particles less than 2.5 μm in diameter (PM_2.5), as measured by ion chromatography (US-EPA 300 method). The GUM method is not typically used to report uncertainty. In general, the analytical results only report the measurement’s standard deviation under repetition as an uncertainty; thus, not all sources of uncertainty are considered. In this work, the major sources of uncertainty regarding the measurements were identified as contributions to linear least square regression lines, repeatability, precision, and trueness. The expanded uncertainty was approximately 20% for anions and cations. The largest contribution to uncertainty was found to be repeatability.     

Ion chromatographic and spectrometric determination of water-soluble compounds in airborne particulates, and their correlations in an industrial area in Attica, Greece

In the time period from June 2005 to May 2006 in 42 sampling campaigns 84 filter samples of airborne particulate matter, coarse (PM_10–2.5) and fine (PM_2.5), were collected using a Gent stacked filter unit in the coastal industrial area of Aspropyrgos in Attica, Greece. The average PM₁₀ (PM_10–2.5 + PM_2.5) concentration was found to be 66 μg · m⁻³, exceeding more than 1.6 times the annual limit of 40 μg · m⁻³. The samples were analysed for Cl⁻, NO₃ ⁻, SO₄ ²⁻, Ca²⁺, Mg²⁺, Na⁺, K⁺ and NH₄ ⁺ using ion chromatography. The data were compared with results obtained with other spectrometric methods, such as inductively coupled plasma-atomic emission spectrometry, atomic absorption spectrometry, energy dispersive X-ray fluorescence and reflectometry. The determined average ionic content comprised about 44% of the PM₁₀ mass. The ionic composition, as well as the possible matrix compounds in both fractions were evaluated by dividing the sampling period into summer and winter season. In the PM_10–2.5/PM_2.5 fraction in summer time the concentrations of Ca²⁺, Mg₂₊ and NO₃ ⁻ were enriched in the coarse fraction. In winter time all species were enriched in the coarse fraction, especially Ca²⁺, Cl⁻ and NO₃ ⁻. NH₄ ⁺ was constantly higher in the fine fraction in summer as well as in winter time. Factor analysis was applied to obtain correlations between cations and anions leading to matrix compounds in both fractions. From the evaluation of the results obtained, some of the local air pollution sources could be identified. Correspondence: Klaus-Michael Ochsenkühn, Laboratory for Trace Element Studies, Institute of Physical Chemistry, NCSR “Demokritos”, Aghia Paraskevi 15310, Athens, Greece     

Single-run ion chromatographic separation of inorganic and low-molecular-mass organic anions under isocratic elution: Application to environmental samples

For the isocratic ion chromatography (IC) separation of low-molecular-mass organic acids and inorganic anions three different anion-exchange columns were studied: IonPac AS14 (9 μm particle size), Allsep A-2 (7 μm particle size), and IC SI-50 4E (5 μm particle size). A complete baseline separation for all analyzed anions (i.e., F⁻, acetate, formate, Cl⁻, NO₂⁻, Br⁻, NO₃⁻, HPO₄²⁻ and SO₄²⁻) in one analytical cycle of shorter than 17 min was achieved on the IC SI-50 4E column, using an eluent mixture of 3.2 mM Na₂CO₃ and 1.0 mM NaHCO₃ with a flow rate of 1.0 mL min⁻¹. On the IonPac AS14 column, it was possible to separate acetate from inorganic anions in one run (i.e., less than 9 min), but not formate, under the following conditions: 3.5 mM Na₂CO₃ plus 1.0 mM NaHCO₃ with a flow rate of 1.2 mL min⁻¹. Therefore, it was necessary to adapt a second run with a 2.0 mM Na₂B₄O₇ solution as an eluent under a flow rate of 0.8 mL min⁻¹ for the separation of organic ions, which considerably enlarged the analysis time. For the Allsep A-2 column, using an eluent mixture of 1.2 mM Na₂CO₃ plus 1.5 mM NaHCO₃ with a flow rate of 1.6 mL min⁻¹, it was possible to separate almost all anions in one run within 25 min, except the fluoride-acetate critical pair. A Certified Multianion Standard Solution PRIMUS for IC was used for the validation of the analytical methods. The lowest RSDs (less than 1%) and the best LODs (0.02, 0.2, 0.16, 0.11, 0.06, 0.05, 0.04, 0.14 and 0.09 mg L⁻¹ for F⁻, Ac⁻, For⁻, Cl⁻, NO₂⁻, Br⁻, NO₃⁻, HPO₄²⁻ and SO₄²⁻, respectively) were achieved using the IC SI-50 4E column. This column was applied for the separation of concerned ions in environmental precipitation samples such as snow, hail and rainwater.     

Speciation analysis of aluminium and aluminium fluoride complexes by HPIC-UVVIS

The study presents a new analytical method for speciation analysis in fractionation of aluminium fluoride complexes and free Al³⁺ in soil samples. Aluminium speciation was studied in model solutions and soil extract samples by means of high performance ion chromatography (HPIC) with UV-VIS detection using post-column reaction with tiron for the separation and detection of aluminium fluoride complex and Al³⁺ forms during one analysis. The paper presents particular stages of the chromatographic process optimization involving selecting the appropriate eluent strength, type of elution or concentration and quantity of derivatization reagent. HPIC was performed on a bifunctional analytical column Dionex IonPac CS5A. The use of gradient elution and the eluents A: 1 M NH₄Cl and B: water acidified to pH of eluent phase, enabled full separation of fluoride aluminium forms as AlF₂⁺, AlF₃⁰, AlF₄⁻ (first signal), AlF²⁺ (second signal) and form Al³⁺ in a single analytical procedure. The proposed new method HPIC-UVVIS was applied successfully in the quantitative and qualitative analysis of soil samples.     

New methods for the direct determination of dissolved inorganic, organic and total carbon in natural waters by Reagent-Free Ion Chromatography and inductively coupled plasma atomic emission spectrometry

New methods have been developed and applied successfully for the determination of dissolved inorganic, organic and total carbon in water samples. The new methods utilize two instrumental setups, Reagent-Free™ Ion Chromatography (RF™-IC) and inductively coupled plasma atomic emission spectrometry (ICP-AES). Dissolved inorganic carbon (DIC) was measured in untreated samples along with Cl⁻, F⁻ and SO₄²⁻ using RF™-IC and by in-line mixing with 0.1 M HNO₃ to enhance CO₂ removal in the nebulizer, followed by ICP-AES analysis. Total dissolved carbon (TDC) was measured by in-line mixing with 0.1 M NaOH following ICP-AES analysis. Dissolved organic carbon (DOC) was obtained as the difference between DIC and TDC. Only non-volatile organic carbon could be detected by the present method. The workable limits of detection obtained in the present study were 0.5 mM (RF™-IC) and 0.1 mM (ICP-AES) for dissolved inorganic and organic carbon, respectively. The power of the new methods lies in routine analysis of DIC and DOC in samples of natural waters of variable composition and salinity using analytical techniques and facilities available in most laboratories doing water sample analysis. The techniques are sensitive and precise, can be automated using gas-tight sample vials and auto-samplers, and are independent of most elemental interferences with the exception of chloride overload by saline samples when using RF™-IC. The new methods were successfully applied for analysis of DIC and DOC in selected samples of natural and synthetic waters.     

Determination of mercury and methylmercury in seafood by ion chromatography using photo-induced chemical vapor generation atomic fluorescence spectrometric detection

A novel method based on photo-induced chemical vapor generation (CVG) as interface to on-line coupled Hg-cysteine ion chromatograpy (IC) with atomic fluorescence spectrometry (AFS) was developed for rapid determination of methylmercury (MHg) in seafood. Separation of inorganic mercury (Hg²⁺) and methylmercury(CH₃Hg⁺) was accomplished on a Hamilton PRP X-200 polymer-based exchange column with a mobile of 3% acetonitrile, 1% (w/w) L-cysteine and 20 mmol L^{− 1} pyridine and 160 mmol L^{− 1} formic acid, at pH 2.4 within 7 min. Once separated, both species are reduced by formic acid in mobile phase under UV radiation to convert Hg⁰ on-line, which is subsequently swept (by argon carrier gas) into an atomic fluorescence spectrometry (AFS) for measurement. Under the optimized experiment conditions, the detection limits (as Hg), based on three times the standard deviation of a standard solution, were found to be 0.1 ng mL^{− 1} for mercury and 0.08 ng mL^{− 1} for methylmercury, with an injection volume of 100 μL. The developed method was validated by determination of certified reference material DORM-2 and was further applied in determination of seafood samples.     

An improved flow analysis-ion chromatography method for determination of cationic and anionic species at trace levels in Antarctic ice cores

A method was developed for the quantitative determination of cations and anions in Antarctic ice cores at μg L⁻¹ and sub-μg L⁻¹ levels by ion chromatography (IC), after ultra-clean decontamination procedures. Strict manipulation and decontamination procedures were used in sub-sampling, in order to minimise sample contamination. Na⁺, NH₄⁺, K⁺, Mg²⁺ and Ca²⁺ were determined by 12-min isocratic elution (H₂SO₄ eluent). Contemporaneously, in a parallel device, F⁻, MSA (methanesulfonic acid), Cl⁻, NO₃⁻ and SO₄²⁻ were analysed in a single 12-min run with multiple-step elution using Na₂CO₃/NaHCO₃ as eluent. Melted ice samples were pumped from their still-closed containers (polystyrene accuvettes with polyethylene caps), shared between the two ion chromatographic systems, online filtered (0.45 μm Teflon membrane) and pre-concentrated (anions and cations pre-concentration columns) using a flow analysis system, thus avoiding uptake of contaminants from the laboratory atmosphere. Sensitivity, linear range, reproducibility and detection limit were evaluated for each chemical species. Anion or cation detection limits ranged from 0.01 to 0.15 μg L⁻¹ by using a relatively small sample volume (1.5 mL). Such values are significantly lower than those reported in literature for almost all the components. These methods were successfully applied to the analysis of cations and anions at trace levels in the Dome C ice core. The composition of the atmospheric aerosol for the last 850 kyr was reconstructed by high-resolution continuous chemical stratigraphies. Concentration trends in the last nine glacial-interglacial climatic cycles were shown and briefly discussed.     

Multivariate statistical study of simultaneously monitored cloud water, aerosol and rainwater data from different elevation levels in an Alpine valley (Achenkirch, Tyrol, Austria)

The present paper deals with data interpretation of monitoring of various atmospheric events (cloud water, aerosol and rainwater) at three different elevation levels at Achenkirch profile in an Alpine valley, Tyrol, Austria (Christlumkopf-1758 m, Christlumalm-1280 m and Talboden-930 m a.s.l.) by the use of principal components analysis. From October 1995 to September 1996 sampling sessions for all sites from the profile and for all events were performed for the major ions NH₄⁺, Na⁺, K⁺, Ca²⁺, Mg²⁺, Cl⁻, NO₃⁻, SO₄²⁻-44 cases with eight variables for rainwater; 117 cases with eight variables for cloud water samples and 50 cases with seven variables for aerosol (the major ions as in rain- and cloud water but without magnesium) at any of the elevations. The aim of the multivariate statistical treatment was to extract information about latent factors determining the data structure in all of the cases in order to compare and interpret similarities and dissimilarities with respect to the elevation or the type of the atmospheric event. Four latent factors seem to explain over 85% of the total variance for almost all sites and events but the factors have different identification for the different events or sites (e.g. ‘anthropogenic’, ‘crustal’, ‘neutralization’, ‘salt’). Thus, a comparison between sites and between events becomes possible. It was found that cloud water and aerosol events are much more similar with respect to data structure (relevant to emission sources or processes of formation) than the same events and rainwater. Further, the upper sites of the profile (Christlumkopf and Christlumalm) also reveal data structure similarity differing from that of the lowest site Talboden.     

Direct determination of arsine in gases by inductively coupled plasma-dynamic reaction cell-mass spectrometry

Reliable determination of arsine (AsH₃) in gases is of great importance due to stringent regulations associated with health, safety and environmental issues. It is, however, challenging for an analyst to determine trace airborne arsine concentrations without specifically designed collection procedures using adsorption, desorption, dissolution or impinging techniques. To circumvent such technical barrier, we have newly developed a direct analytical method, characterized by introduction of an arsine gas sample into stable plasma stream, followed by gas-phase oxidation of arsine with molecular oxygen in a dynamic reaction cell (DRC) equipped within the inductively coupled plasma-mass spectrometry (ICP/MS) system, followed by subsequent detection of AsO⁺ ion. This preliminary work used trace arsine concentrations (161 μg m⁻³, 322 μg m⁻³, and 645 μg m⁻³) gravimetrically prepared in N₂ balance. The proposed method was optimized for the important experimental parameters such as the flow rates of the reaction gas, the arsine sample, and the carrier gas. This method was then validated by demonstrating good figure-of-merits including the low limit of detection (0.10 μg m⁻³), good linearity (r² > 0.9915), low measurement uncertainty (0.66%), and high speed of analysis (<6 min). The proposed method is expected to be potentially applicable to the determination of arsine in real workplace air after appropriate modifications are made.     

Nuclear magnetic resonance spectroscopic study on ionic liquids of 1-alkyl-3-methylimidazolium salts

Chemical shifts of ¹H and ¹³C NMR of series of methylimidazolium salts (MIM⁺, X=Br⁻, BF₄⁻ and PF₆⁻) function on the length of alkyl groups on the ring, type of solvents and the concentration. The bromides series demonstrate more chemical shift variation on H2 upon the change of solvents and concentration. Unexpected H-D exchange reactions were also observed in the MIM⁺Br⁻ by using CD₃OD and D₂O. The exchange rates strongly depend on the length of the alkyl group, which could cause more steric factor to reduce the interaction between deuterium atom from solvent and C2 of the ring.     

Highly sensitive and selective amperometric sensors for nanomolar detection of iodate and periodate based on glassy carbon electrode modified with iridium oxide nanoparticles

Iridium oxide nanoparticles are grown on a glassy carbon electrode by electrodepositing method. The electrochemical behavior and electrocatalytic activity of modified electrode towards reduction of iodate and periodate are studied. The reductions of both ions occur at the unusual positive peak potential of 0.7 V vs. reference electrode. The modified electrode is employed successfully for iodate and periodates detection using cyclic voltammetry, hydrodynamic amperometry and flow injection analysis (FIA). In the performed experiments, flow injection amperometric determination of iodate and periodate yielded calibration curves with the following characteristics: linear dynamic range up to 100 and 80 μM, sensitivity of 140.9 and 150.6 nA μM⁻¹ and detection limits of 5 and 36 nM, respectively. The repeatability of the modified electrode for 21 injections of 1.5 μM of iodate solution is 1.5%. The interference effects of NO₂⁻, NO₃⁻, ClO₃⁻, BrO₃⁻, ClO₄⁻, SO₄²⁻, Cu²⁺, Zn²⁺, Mn²⁺, Mg²⁺, Cd²⁺, Ca²⁺, Na⁺, K⁺, NH₄⁺ and K⁺, CH₃COO⁻ and glucose were negligible at the concentration ratio of more than 1000. The obtained attractive analytical performance together with high selectivity and simplicity of the proposed method provide an effective and e novel modified electrode to develop an iodate and periodate sensor. Sensitivity, selectivity, the liner concentration range and the detection limit of the developed sensor are all much better than all known similar sensors in the literature for iodate and periodate determination.     

Label-free capacitive immunosensor based on quartz crystal Au electrode for rapid and sensitive detection of Escherichia coli O157:H7

The capability of ICP-MS equipped with the high matrix introduction system (HMI) for accurate analysis of lanthanoids in environmental samples was investigated. Compared to the conventional operation, the amounts of oxide and hydroxide molecular species formed in the plasma were reduced by up to 5 times. The relative yields of oxides did not exceed 0.02% for BaO⁺ species and were as low as 0.3% for lanthanoids with the highest oxide-formation rates (LaO⁺, CeO⁺, PrO⁺ and NdO⁺). Hydroxide formation was less than 0.02% when HMI system was used. In addition, two digestion procedures were evaluated by the analysis of standard reference materials (SRMs) of different matrices. The digestion efficiency and limits of detection (LOD) were improved when samples were digested with a mixture of HNO₃/H₂O₂/HCl/HF, and HF was removed by evaporation in presence of concentrated HCl. Using this procedure and HMI-ICP-MS analysis, LOD ranged from 0.1 μg kg⁻¹ to 6 μg kg⁻¹. Recoveries ranged from 85 to 115% for La to Ho and from 75 to 85% for the other lanthanoids. Relative standard deviations for replicate analysis of SRMs were less than 10%.     

Characterisation of the seasonal exposure to air pollutants for a respiratory epidemiological study

In 2006, elementary schools of inner-city Lisbon, Portugal were given questionnaires to identify respiratory problems. In 1,175 children aged 5–10 years, 27.7% reported rhinitis, 2.5% reported hay fever and 25.9% reported asthma symptoms. April and August were the months with higher incidence of rhinitis, with a considerable difference nonetheless (10.5% and 2.3%, respectively.). The former trends are addressed here by using meteorological data, PM_2.5, and its elemental speciation. Mann-Whitney U-tests were applied to the data sets. Significantly higher values were found for humidity, K⁺, NH₄ ⁺, Sb and Zn in April, and for temperature, Cl⁻, Mg²⁺ and Na⁺ in August. Commuter and heavy-duty traffic may contribute to rhinitis episodes.     

Optimisation of a liquid chromatography-tandem mass spectrometric method for the determination of acrylamide in foods

A robust and fitted routine method resulting from an analytical optimisation has been applied for the determination of acrylamide in several foods including mainly potato and cereal products. For the sample treatment, different materials were evaluated for filtration and purification of the extract. To increase the performances in terms of sensitivity, a preconcentration to small volume was introduced before liquid chromatography coupled to tandem mass spectrometry analysis on a μ-Bondapak C₁₈ column using d₃-acrylamide as internal standard. For identification, relative retention time and two diagnostic ions were monitored. A limit of detection of 10 μg kg⁻¹, a limit of quantitation of 20 μg kg⁻¹, mean recoveries ranging from 100 to 115%, coefficients of variation from 1.36 to 8.06% for repeatability and from 3.3 to 18.2% for reproducibility within the laboratory and a measurement uncertainty of 42% were obtained during an in-house validation procedure. Results of tests, validation data and Z-score obtained during participation to proficiency studies are presented.     

On the chemical resolution of the 87Rb+ (s0)/87Sr+ (s1) isobaric interference: a kinetic search for an optimum reagent

Room-temperature reactions of the atomic cations Sr⁺ and Rb⁺ have been surveyed systematically with a variety of gases using an Inductively-Coupled Plasma/Selected-Ion Flow Tube (ICP/SIFT) tandem mass spectrometer. Rate coefficients and product distributions have been measured in He buffer gas at 0.35 Torr and 295 K for reactions of Sr⁺ and Rb⁺ with CH₃F, CH₃Cl, N₂O, CO₂, CS₂, SF₆, D₂O and NH₃. Rb⁺ (s⁰) is seen to be quite inert with these molecules and reacts either slowly by molecule addition or not at all, while Sr⁺ (s¹) is much more reactive with all these 8 molecules, especially with CH₃F, CH₃Cl, N₂O and SF₆. Sr⁺ reacts with CH₃F and SF₆ by F-atom transfer, with CH₃Cl by Cl-atom transfer and with N₂O by O-atom transfer, and the reaction rate coefficients are all quite high, k ≥ 1.4 × 10⁻¹¹ cm³ molecules⁻¹ s⁻¹. The extreme differences in reactivity with CH₃F, SF₆, CH₃Cl and N₂O provide a chemical basis for the separation of isobaric interferences of ⁸⁷Rb⁺ and ⁸⁷Sr⁺ often encountered in ICP-MS. Among these four molecules, SF₆ exhibits the largest difference in reactivity, almost a factor of 10⁴, and so is identified as the kinetically recommended reagent for the chemical resolution of the isobaric interference of ⁸⁷Rb⁺ and ⁸⁷Sr⁺.