Highly sensitive and selective room temperature NH3 gas microsensor using an ionic conductor (CuBr) film

A new ammonia gas microsensor was developed, based on the large resistance change of an ionic conductor (CuBr) film when exposed to low NH₃ concentrations. The detection is based on specific interactions between ammonia molecules contained in the gas atmosphere and mobile copper ions in the copper(I) bromide layer. The sensor is operating at ambient temperature and allows highly sensitive and specific ammonia detection. The sensor works at ammonia concentrations between 1 and 500 ppm. There are no significant cross-effects to acetylene and carbon monoxide and only a weak cross-sensitivity to hydrogen sulfide gas (200 ppm). The selectivity was experimentally compared with commercial tin dioxide sensors (TGS 826). The sensor fabrication is a simple process, allowing low cost device production.     

Fabrication of a gas sensor using pentacene thin films as a detector

Highly sensitive gas sensors for both acidic and basic gases were fabricated based on conducting thin films of polyacene compounds. Gas sensors formed with pentacene thin films deposited on various kinds of substrates were found to exhibit high sensitivity in detecting subppm concentrations of NO₂ or Cl₂ by monitoring the conductivity of the thin film. Improvements in the conductance and duration period for detection were achieved by changing the shape of electrodes and substrate. The sensors with PEN thin films initially doped with iodine could detect ppm concentrations of ammonia gas, since iodine molecules were dedoped upon exposure to ammonia, causing the reduction of the conductivity.     

A new sensor for ammonia based on cyanidin-sensitized titanium dioxide film operating at room temperature

Design and fabrication of an ammonia sensor operating at room temperature based on pigment-sensitized TiO₂ films was described. TiO₂ was prepared by sol–gel method and deposited on glass slides containing gold electrodes. Then, the film immersed in a 2.5 × 10⁻⁴ M ethanol solution of cyanidin to absorb the pigment. The hybrid organic–inorganic formed film here can detect ammonia reversibly at room temperature. The relative change resistance of the films at a potential difference of 1.5 V is determined when the films are exposed to atmospheres containing ammonia vapors with concentrations over the range 10–50 ppm. The relative change resistance, S, of the films increased almost linearly with increasing concentrations of ammonia (r = 0.92). The response time to increasing concentrations of the ammonia is about 180–220 s, and the corresponding values for decreasing concentrations 240–270 s. At low humidity, ammonia could be ionized by the cyanidin on the TiO₂ film and thereby decrease in the proton concentration at the surface. Consequently, more positively charged holes at the surface of the TiO₂ have to be extracted to neutralize the adsorbed cyanidin and water film. The resistance response to ammonia of the sensors was nearly independent on temperature from 10 to 50 °C. These results are not actually as good as those reported in the literature, but this preliminary work proposes simpler and cheaper processes to realize NH₃ sensor for room temperature applications.     

Carbon nanotube networks as gas sensors for NO2 detection

Networks of different carbon nanotube (CNT) materials were investigated as resistive gas sensors for NO₂ detection. Sensor films were fabricated by airbrushing dispersions of double-walled and multi-walled CNTs (DWNTs and MWNTs, respectively) on alumina substrates. Sensors were characterized by resistance measurements from 25 to 250 °C in air atmosphere in order to find the optimum detection temperature. Our results indicate that CNT networks were sensitive to NO₂ concentrations as low as 0.1 ppm. All tested sensors provided significantly lower response to interfering gases such as H₂, NH₃, toluene and octane. We demonstrate that the measured sensitivity upon exposure to NO₂ strongly depends on the employed CNT material. The highest sensitivity values were obtained at temperatures ranging between 100 and 200 °C. The best sensor performance, in terms of recovery time, was however achieved at 250 °C. Issues related to the gas detection mechanisms, as well as to CNT network thermal stability in detection experiments performed in air at high operation temperatures are also discussed.     

Fabrication of an ammonia gas sensor using inkjet-printed polyaniline nanoparticles

This work details the fabrication and performance of a sensor for ammonia gas analysis which has been constructed via the inkjet-printed deposition of polyaniline nanoparticle films. The conducting films were assembled on interdigitated electrode arrays and characterised with respect to their layer thickness and thermal properties. The sensor was further combined with heater foils for operation at a range of temperatures. When operated in a conductimetric mode, the sensor was shown to exhibit temperature-dependent analytical performance to ammonia detection. At room temperature, the sensor responded rapidly to ammonia (t₅₀ = 15 s). Sensor recovery time, response linearity and sensitivity were all significantly improved by operating the sensor at temperatures up to 80 °C. The sensor was found to have a stable logarithmic response to ammonia in the range of interest (1-100 ppm). The sensor was also insensitive to moisture in the range from 35 to 98% relative humidity. The response of the sensor to a range of common potential interferents was also studied.     

Sensitive coating for water vapors detection based on thermally sputtered calcein thin films

In this paper the adsorption properties of thermally sputtered calcein thin films towards water and other polar molecules vapors are studied by different characterization techniques: quartz crystal microbalance, surface plasmon resonance and visible spectroscopy. Sensitivity of calcein thin films to water vapors resulted much higher as compared with those of a number of dyes whose structure was close to that of calcein. All types of sensors with calcein coatings have demonstrated linear concentration dependences in the wide range of water vapor pressure from low concentrations up to 27,000 ppm (close to saturation). At higher concentrations of water vapor all sensors demonstrate the abrupt increase of the response (up to two orders). A theoretical model is advanced explaining the adsorption properties of calcein thin films taking into account their chemical structure and peculiarities of molecular packing. The possibility of application of thermally sputtered calcein films in sensing technique is discussed.     

Miniaturized measurement system for ammonia in air

The development of a miniaturized ammonia sensor made using microsystem technology is described. Gas is sampled in a sampler comprising two opposite channels separated by a gas permeable, water repellent polypropylene membrane. Subsequently, the acid sample solution is pumped into a selector where an alkaline solution is added to ionize all sampled ambient acid gasses, resulting in an enhanced selectivity. In the selector, the ammonia can diffuse through a second membrane into a purified water stream where an electrolyte conductivity sensor quantifies the resulting ammonium concentration. The realized system is shown to be selective enough not to be influenced by normal ambient carbon dioxide concentrations. Experiments with a gas flow of 3 ml/min, containing ammonia concentrations ranging from 9.8 to 0.3 ppm in a nitrogen carrier flow, into a 15 μl/min sample solution flow and finally into a 5 μl/min purified water stream have been carried out and show that the system is sensitive to ammonia concentration below 1 ppm.     

Polyaniline coated micro-capillaries for continuous flow analysis of aqueous solutions

The inner walls of fused silica micro-capillaries were successfully coated with polyaniline nanofibres using the “grafting” approach. The optical response of polyaniline coatings was evaluated during the subsequent redoping–dedoping processes with hydrochloric acid and ammonia solutions, respectively, that were passed inside the micro-capillary in continuous flow. The optical absorbance of the polyaniline coatings was measured and analysed in the wavelength interval of [300–850 nm] to determine its optical sensitivity to different concentrations of ammonia. It was found that the optical properties of polyaniline coatings change in response to ammonia solutions in a wide concentration range from 0.2 ppm to 2000 ppm. The polyaniline coatings employed as a sensing material for the optical detection of aqueous ammonia have a fast response time and a fast regeneration time of less than 5 s at room temperature. The coating was fully characterised by scanning electron microscopy, Raman spectroscopy, absorbance measurements and kinetic studies. The response of the coatings showed very good reproducibility, demonstrating that this platform can be used for the development of micro-capillary integrated sensors based on the inherited sensing properties of polyaniline.     

Influence of the liquid crystal behaviour on the Langmuir and Langmuir-Blodgett film supramolecular architecture of an ionic liquid crystal

Novel fluorescent poly(2-(acetoacetoxy)ethyl methacrylate)(PAAEMA) latexes have been synthesized by miniemulsion polymerization employing a polymeric costabilizer. Nanoscale aggregates of macromolecules bearing β-dicarbonyl are formed in the prepared latex particles. Ammonia and the β-dicarbonyl aggregates assemble a supramolecular complex, which exhibits strong visible fluorescence under UV light. The formation of the complex is confirmed by the characteristic absorption peak located at about 275 nm in UV-Vis spectra. The absorption spectrum has been found to be applicable for ammonia detection. Atomic Force Microscopy (AFM) studies of surface morphology reveal that gas-sensing properties of the PAAEMA thin films involve the reversible absorption and desorption of ammonia. PAAEMA thin films are sensitive to ammonia gas and have a short response time of 80s when exposed to 54 ppm of ammonia gas concentration.     

Novel flexible chemical gas sensor based on poly(3,4-ethylenedioxythiophene) nanotube membrane

Poly(3,4-ethylenedioxythiophene) nanotubes (PEDOT NTs) flexible membrane was successfully fabricated by vapor deposition polymerization (VDP) mediated electrospinning for ammonia gas detection. PVA nanofibers (NFs) were electrospun as a core part and polyvinyl alcohol (PVA)/PEDOT coaxial nanocables (NCs) were prepared by VDP method via EDOT monomer adsorption onto the electrospun PVA NFs as templates. To obtain the PEDOT NTs membrane, the PVA NFs were removed from PVA/PEDOT coaxial NCs with distilled water. PVA/PEDOT coaxial NCs and PEDOT NTs had the conductivities of 71 and 61 S cm⁻¹ and were applied as a transducer for ammonia gas detection in the range of 1-100 parts per million (ppm) of NH₃ gas. They exhibited the minimum detectable level of ca. 5 parts per million (ppm) and fast response time (less than 1 s) towards ammonia gas. In a recovery time, the PEDOT NTs membrane sensor was ca. 30 s and shorter compared to that of the membrane sensor based on the PVA/PEDOT NCs (ca. 50 s). In addition, sensor performance of PEDOT NTs membrane was also undertaken as a function of membrane thickness. Thick membrane sensor (30 μm) had the enhanced sensitivity and the sensitivity on the membrane thickness was in the order of 30 μm > 20 μm > 10 μm at 60 ppm of NH₃ gas.     

The detection of organosphosphonates by polymer films on a surface acoustic wave device and a micromirror fiberoptic sensor

There is a need for sensitive detection of organophosphonates by inexpensive, portable instruments. Two kinds of chemical sensors, based on surface acoustic wave (SAW) devices and fiberoptic micromirrors, show promise for such sensing systems. Chemically sensitive coatings are required for detection, and data for thin films of the polymer polysiloxane are reported for both kinds of physical transducers. Both kinds of sensors are shown to be capable of detecting concentrations of diisopropylmethylphosphonate (DIMP) down to 1 ppm.     

Sol–gel derived mesoporous Pt and Cr-doped WO<Subscript>3</Subscript> thin films: the role played by mesoporosity and metal doping in enhancing the gas sensing properties

Mesoporous Cr or Pt-doped WO₃ thin films to be employed as ammonia gas sensors were prepared by a fast one-step sol–gel procedure, based on the use of triblock copolymer as templating agent. The obtained films were constituted by aggregates of interconnected WO₃ nanocrystals (20–50 nm) separated by mesopores with dimensions ranging between 2 and 15 nm. The doping metals, Pt and Cr, resulted differently hosted in the WO₃ mesoporous matrix. Chromium is homogeneously dispersed in the oxide matrix, mainly as Cr(III) and Cr(V) centers, as revealed by EPR spectroscopy; instead platinum segregated as Pt (0) nanoparticles (4 nm) mainly included inside the WO₃ nanocrystals. The semiconductor layers containing Pt nanoclusters revealed, upon exposure to NH₃, remarkable electrical responses, much higher than Cr-doped and undoped layers, particularly at low ammonia concentration (6.2 ppm). This behavior was attributed to the presence of Pt nanoparticles segregated inside the semiconductor matrix, which act as catalysts of the N–H bond cleavage, decreasing the activation barrier in the ammonia dissociation. The role of the mesoporous structure in influencing the chemisorption and the gas diffusion in the WO₃ matrix appeared less decisive than the electronic differences between the two examined doping metals. The overall results suggest that a careful combination between mesoporous architecture and metal doping can really promote the electrical response of WO₃ toward ammonia.     

Polymer/Ordered mesoporous carbon nanocomposite platelets as superior sensing materials for gas detection with surface acoustic wave devices

We have prepared nanocomposites of polymers and platelet CMK-5-like carbon and have demonstrated their superior performance for gravimetric gas detection. The zirconium-containing platelet SBA-15 was used as hard template to prepare CMK-5-like carbon, which was then applied as a lightweight and high-surface-area scaffold for the growth of polymers by radical polymerization. Mesoporous nanocomposites composed of four different polymers were used as sensing materials for surface acoustic wave devices to detect ppm-level ammonia gas. The sensors showed much better sensitivity and reversibility than those coated with dense polymer films, and the sensor array could still generate a characteristic pattern for the analyte with a concentration of 16 ppm. The results show that the nanocomposite sensing materials are promising for highly sensitive gravimetric-type electronic nose applications.     

Highly sensitive optical humidity probe

A highly sensitive optical humidity probe based on reflectance measurements has been developed using Nafion^®-crystal violet (CV) films. This sensor can be used to calibrate relative humidity (RH) in the range 0-0.25% with a detection limit (blank signal + 3σ_b, where σ_b = the standard deviation (S.D.) of the blank signal) of 0.018% RH (∼4.37 ppm) and exhibited low hysteresis. The sensor films were fully reversible in dry nitrogen and reversal times were shown to be dependent on exposure time and % RH. The response to 1% RH was highly reproducible (S.D. = 1.67%, number of samples (n) = 5). Hydrogen chloride gas did not interfere with the response of the sensor to RH but did reduce sensor reversal times. This sensor displayed sufficient sensitivity that it could be used to detect ppm levels of moisture in process gases such as nitrogen and HCl.     

Optical fiber evanescent wave absorption spectrometry of nanocrystalline tin oxide thin films for selective hydrogen sensing in high temperature gas samples

SnO₂ nanocrystalline material was prepared with a sol-gel process and thin films of the nanocrystalline SnO₂ were coated on the surface of bent optical fiber cores for gas sensing. The UV/vis absorption spectrometry of the porous SnO₂ coating on the surface of the bent optical fiber core exposed to reducing gases was investigated with a fiber optical spectrometric method. The SnO₂ film causes optical absorption signal in UV region with peak absorption wavelength at around 320 nm when contacting H₂-N₂ samples at high temperatures. This SnO₂ thin film does not respond to other reducing gases, such as CO, CH₄ and other hydrocarbons, at high temperatures within the tested temperature range from 300 °C to 800 °C. The response of the sensing probe is fast (within seconds). Replenishing of the oxygen in tin oxide was demonstrated by switching the gas flow from H₂-N₂ mixture to pure nitrogen and compressed air. It takes about 20 min for the absorption signal to decrease to the baseline after the gas sample was switched to pure nitrogen, while the absorption signal decreased quickly (in 5 min) to the baseline after switching to compressed air. The adhesion of tin oxide thin films is found to be improved by pre-coating a thin layer of silica gel on the optical fiber. Adhesion increases due to increase interaction of optical fiber surface and the coated silica gel and tin oxide film. Optical absorption spectra of SnO₂ coating doped with 5 wt% MoO₃ were observed to change and red-shifted from 320 nm to 600 nm. SnO₂ thin film promoted with 1 wt% Pt was found to be sensitive to CH₄ containing gas.     

Surface plasmon resonance sensor for lysozyme based on molecularly imprinted thin films

Molecularly imprinted polymers (MIPs) selective for lysozyme were prepared on SPR sensor chips by radical co-polymerization with acrylic acid and N,N′-methylenebisacrylamide. Gold-coated SPR sensor chips were modified with N,N′-bis(acryloyl)cystamine, on which MIP thin films were covalently conjugated. The presence of NaCl during the polymerization and the re-binding tests affected the selectivity and the optimization of NaCl concentration in the pre-polymerization mixture and the re-binding buffer could enhance the selectivity in the target protein sensing. When the lysozyme-imprinted polymer thin films were prepared in the presence of 40 mM NaCl, the selectivity factor (target protein bound/reference protein bound) of MIP in the re-binding buffer containing 20 mM NaCl was 9.8, meanwhile, that of MIP in the re-binding buffer without NaCl was 1.2. A combination of SPR sensing technology with protein-imprinted thin films is a promising tool for the construction of selective protein sensors.     

A method for the detection of alcohol vapours based on optical sensing of magnesium 5,10,15,20-tetraphenyl porphyrin thin film by an optical spectrometer and principal component analysis

In this work we have proposed a method for the detection of alcohol vapours, i.e. methanol, ethanol and isopropanol, based on the optical sensing response of magnesium 5,10,15,20-tetraphenyl porphyrin (MgTPP) thin films, as measured by optical spectrometry with the assistance of chemometric analysis. We have implemented a scheme which allows a laboratory UV–vis spectrometer to act as a so-called “electronic nose” with very little modification. MgTPP thin films were prepared by a spin coating technique, using chloroform as the solvent, and then subjected to thermal annealing at 280 °C in an argon atmosphere. These MgTPP optical gas sensors presented significant responses with methanol compared to ethanol and isopropanol, based on the dynamic flow of alcohol vapours at the same mol% of alcohol concentration. Density functional theory (DFT) calculations were performed to model the underlying mechanism of this selectivity. The performance of the optical gas sensors was optimised by varying the fabrication parameters. It is hoped that the MgTPP thin film together with an off-the-shelf optical spectrometer and a simple chemometrics algorithm can be a valuable tool for the analysis of alcoholic content in the beverage industry.     

Chemical deposition of semiconducting cadmium selenide quantum dots in thin film form and investigation of their optical and electrical properties

Cadmium selenide quantum dots with cubic crystal structure are chemically deposited in thin film form using selenosulfate as a precursor for selenide ions and ammonia buffer with double role: as a ligand and as a pH value controller. The optical band gap energies of as-deposited and thermally treated cadmium selenide thin films, calculated within the framework of parabolic approximation for the dispersion relation, on the basis of equations which arise from the Fermi's golden rule for electronic transitions from valence to conduction band, are 2.08 and 1.77 eV, correspondingly. The blue shift of band gap energy of 0.34 eV for as-deposited thin films with respect to the bulk value is due to the quantum size effects (i.e., nanocrystals behave as quantum dots) and this finding is in agreement with the theoretical predictions. During the thermal treatment the nanocrystals are sintered, the increase of crystal size being in correlation with the decrease of band gap energy. The annealed thin films are practically non-quantized. From the resistance-temperature measurements, on the basis of the dependence of ln(R/Ω) vs 1/T in the region of intrinsic conduction, the thermal band gap energy (at 0 K) of 1.85 eV was calculated.     

TiO2 nanotube, nanowire, and rhomboid-shaped particle thin films fixed on a titanium metal plate

Titanium dioxide thin films having various nanostructures could be formed by various treatments on sodium titanate nanotube thin films approximately 5 μm thick fixed on titanium metal plates. Using an aqueous solution with a lower hydrochloric acid concentration (0.01 mol/L) and a higher reaction temperature (90 °C) than those previously employed, we obtained a hydrogen titanate nanotube thin film fixed onto a titanium metal plate by H⁺ ion-exchange treatment of the sodium titanate nanotube thin film. Calcination of hydrogen titanate nanotube thin films yielded porous thin films consisting of anatase nanotubes, anatase nanowires, and anatase nanoparticles grown directly from the titanium metal plate. H⁺ ion-exchange treatment of sodium titanate nanotube thin films at 140 °C resulted in porous thin films consisting of rhomboid-shaped anatase nanoparticles.     

Nanosized SrCO3-based chemiluminescence sensor for ethanol

The development of a nanosized SrCO₃-based sensor based on the generated chemiluminescence (CL) from catalytic oxidation of organic vapors was demonstrated. The luminescence characteristics and effect of different parameters, such as temperature and flow rate, were discussed with a prepared CL detection system. This sensor was evaluated for the measurement of gaseous ethanol as a model analyte. Under the optimized conditions, the linear range of CL intensity versus concentration of ethanol vapor is 6-3750 ppm (r=0.998, n=8), with the limit of detection of 2.1 ppm. This SrCO₃ sensor shows high selectivity to ethanol. There is no response while the foreign substances, such as gasoline, ammonia and hydrogen, are passing through the sensor. The hydrocarbons can slightly interfere with the ethanol measurement. The sensor also exhibits good stability and durability during 100 h reaction with 2000 ppm ethanol. The interactions between ethanol molecules and SrCO₃ involving CL emission were investigated by utilizing gas chromatography in this paper and the possible mechanism of CL from ethanol oxidation on SrCO₃ was discussed.