CoFe2O4 nano-particles functionalized with 8-hydroxyquinoline for dispersive solid-phase micro-extraction and direct fluorometric monitoring of aluminum in human serum and water samples

A simple dispersive solid-phase micro-extraction method based on CoFe₂O₄ nano-particles (NPs) functionalized with 8-hydroxyquinoline (8-HQ) with the aid of sodium dodecyl sulfate (SDS) was developed for separation of Al(III) ions from aqueous solutions. Al(III) ions are separated at pH 7 via complex formation with 8-HQ using the functionalized CoFe₂O₄ nano-particles sol solution as a dispersed solid-phase extractor. The separated analyte is directly quantified by a spectrofluorometric method at 370 nm excitation and 506 nm emission wavelengths. A comparison of the fluorescence of Al(III)–8-HQ complex in bulk solution and that of Al(III) ion interacted with 8-HQ/SDS/CoFe₂O₄ NPs revealed a nearly 5-fold improvement in intensity. The experimental factors influencing the separation and in situ monitoring of the analyte were optimized. Under these conditions, the calibration graph was linear in the range of 0.1–300 ng mL⁻¹ with a correlation coefficient of 0.9986. The limit of detection and limit of quantification were 0.03 ng mL⁻¹ and 0.10 ng mL⁻¹, respectively. The inter-day and intra-day relative standard deviations for six replicate determinations of 150 ng mL⁻¹ Al(III) ion were 2.8% and 1.7%, respectively. The method was successfully applied to direct determine Al(III) ion in various human serum and water samples.     

Near-infrared fluorimetric determination of nucleic acids by shifting the ion-association equilibrium between tetracarboxy aluminum phthalocyanine and tetra-N-hexadecylpyridiniumyl porphyrin

A new method was developed for determination of micro amounts of nucleic acids based on near-infrared (near-IR) fluorescence recovery, employing a two-reagent system which is composed of an anionic tetracarboxy aluminum phthalocyanine (AlC₄Pc) and a cationic tetra-N-hexadecylpyridiniumyl porphyrin (TC₁₆PyP). The fluorescence of the AlC₄Pc, with the maximum emission wavelength at 701 nm, could be quenched by TC₁₆PyP at its proper concentration, but recovered by adding nucleic acids. Under optimal conditions, the recovered fluorescence is proportional to the concentration of nucleic acids. The calibration graphs are linear over the range of 1-200 ng mL⁻¹ for fish sperm DNA (FS DNA) and 2-400 ng mL⁻¹ for calf thymus DNA (CT DNA). The corresponding detection limits are 0.59 ng mL⁻¹ for FS DNA and 0.82 ng mL⁻¹ for CT DNA, respectively. Four synthetic and three real nucleic acid samples were determined with satisfactory results.     

Highly selective and sensitive paper-based colorimetric sensor using thiosulfate catalytic etching of silver nanoplates for trace determination of copper ions

A novel, highly selective and sensitive paper-based colorimetric sensor for trace determination of copper (Cu²⁺) ions was developed. The measurement is based on the catalytic etching of silver nanoplates (AgNPls) by thiosulfate (S₂O₃²⁻). Upon the addition of Cu²⁺ to the ammonium buffer at pH 11, the absorption peak intensity of AuNPls/S₂O₃²⁻ at 522 nm decreased and the pinkish violet AuNPls became clear in color as visible to the naked eye. This assay provides highly sensitive and selective detection of Cu²⁺ over other metal ions (K⁺, Cr³⁺, Cd²⁺, Zn²⁺, As³⁺, Mn²⁺, Co²⁺, Pb²⁺, Al³⁺, Ni²⁺, Fe³⁺, Mg²⁺, Hg²⁺ and Bi³⁺). A paper-based colorimetric sensor was then developed for the simple and rapid determination of Cu²⁺ using the catalytic etching of AgNPls. Under optimized conditions, the modified AgNPls coated at the test zone of the devices immediately changes in color in the presence of Cu²⁺. The limit of detection (LOD) was found to be 1.0 ng mL⁻¹ by visual detection. For semi-quantitative measurement with image processing, the method detected Cu²⁺ in the range of 0.5–200 ng mL⁻¹(R² = 0.9974) with an LOD of 0.3 ng mL⁻¹. The proposed method was successfully applied to detect Cu²⁺ in the wide range of real samples including water, food, and blood. The results were in good agreement according to a paired t-test with results from inductively coupled plasma-optical emission spectrometry (ICP-OES).     

Effect of dimensions of multi-walled carbon nanotubes on its enrichment efficiency of metal ions from environmental waters

The effect of dimensions (length and external diameter) of multi-walled carbon nanotubes (MWCNTs) on its preconcentration efficiency towards some metal ions (Pb²⁺, Cd²⁺, Cu²⁺, Zn²⁺ and MnO₄⁻) from environmental waters prior to their analysis by flame atomic absorption spectroscopy (FAAS) was investigated. MWCNTs (as-received from the manufacturer) of various external diameters and lengths were involved. Other variables optimized included effects of pH of water sample, composition and volume of eluent, mass of the MWCNTs, breakthrough volume and coexisting ions. Maximum recovery of metal ions was obtained at pH 9 where it was thought that precipitation of metals as their hydroxides played the major factor in metals uptake by MWCNT. It was suggested that the use of appropriate dimensions of MWCNTs may support the trapping process of the precipitated metal hydroxides by MWCNTs. It was found that long MWCNT of length 5-15 μm and external diameter 10-30 nm gave the highest enrichment efficiency towards almost all the targeted metal ions. It could be used for preconcentration of MnO₄⁻, Cu²⁺, Zn²⁺ and Pb²⁺ with almost full recovery; but not for Cd²⁺ due to its low recovery. The optimized solid phase extraction (SPE) procedure was capable of determining metal ions in the linear range 20-100 ng mL⁻¹ (except for Zn²⁺ from 20 to 150 ng mL⁻¹). Detection limits were 0.709 ng mL⁻¹ for MnO₄⁻, 0.278 ng mL⁻¹ for Pb²⁺, 0.465 ng mL⁻¹ for Cu²⁺, 0.867 ng mL⁻¹ for Zn²⁺. Application of the optimized SPE procedure to environmental waters (tap water, reservoir water and stream water) gave spike recoveries of the metals in the range of 81-100%.     

Flow-injection catalytic spectrophotometic determination of molybdenum(VI) in plants using bromate oxidative coupling of p-hydrazinobensenesulfonic acid with N-(1-naphthyl)ethylenediamine

A novel flow-injection spectrophotometry has been developed for the determination of molybdenum(VI) at nanograms per milliliter levels. The method is based on the catalytic effect of molybdenum(VI) on the bromate oxidative coupling of p-hydrazinobenzenesulfonic acid with N-(1-naphthyl)ethylenediamine to form an azo dye (λ_max = 530 nm). Chromotropic acid (4,5-dihydroxy-2,7-naphthalenedisulfonic acid) acted as an effective activator for the molybdenum(VI)-catalyzed reaction and increased the sensitivity of the method. The reaction was monitored by measuring the change in absorbance of the dye produced. The proposed method allowed the determination of molybdenum(VI) in the range 1.0-20 ng mL⁻¹ with sample throughput of 15 h⁻¹. The limit of detection was 0.5 ng mL⁻¹ and a relative standard deviation for 10 ng mL⁻¹ molybdenum(VI) (n = 10) was 2.5%. The interfering ions were eliminated by using the combination of a masking agent and on-line minicolumn packed with cation exchanger. The present method was successfully applied to the determination of molybdenum(VI) in plant foodstuffs.     

Porous redox-active Cu2O-SiO2 nanostructured film: Preparation, characterization and application for a label-free amperometric ferritin immunosensor

A novel Cu₂O-SiO₂ nanostructured particle was synthesized by a solution-phase method and was adopted for construction of a label-free amperometric immunosensor. The porous Cu₂O-SiO₂ nanoparticles had good redox electrochemical activity, large surface-to-volume ratio, film-forming ability and high stability. The physical morphology and structure of Cu₂O-SiO₂ nanoparticles were examined by scanning electron microscope (SEM) and transmission electron microscopy (TEM). The chemical component of Cu₂O-SiO₂ was confirmed by X-ray photoelectron spectroscopy (XPS) and auger electron spectra (AES). The electrode modification process was probed by cyclic voltammetry (CV) and the performance of the immunosensor was studied by differential pulse voltammetry (DPV) measurements. To improve the analytical characteristics of the immunosensor, the experimental conditions were optimized. The immunosensor exhibited a good response to ferritin in ranges from 1.0 to 5.0 and 5.0 to 120.0 ng mL⁻¹ with a detection limit of 0.4 ng mL⁻¹. The fabricated immunosensor could make a low-cost, sensitive, quantitative detection of ferritin, and would have a potential application in clinical immunoassays.     

Highly sensitive spectrofluorimetric kinetic determination of ultratrace amounts of vanadium(V) based on the oxidation of 1,8-diaminonaphthalene by bromate

A highly sensitive catalytic quenching spectrofluorimetric method was described for the determination of V(V) based on its catalytic effect on the oxidation of 1,8-diaminonaphthalene by potassium bromate with Tiron as an activator in weakly acidic medium and the reaction mechanism was investigated. The reaction was followed spectrofluorimetrically by measuring the fluorescence intensity of 1,8-diaminonathphlene (DAN) (λ_ex=356 nm, λ_em=439 nm) at a fixed time of 5 min from initiation of the reaction. Under the optimum conditions, vanadium(V) can be determined in the range 0.05-50.0 ng ml⁻¹ with a S.D.=0.024 for 15 times measurements. The detection limit of the method was down to 0.0088 ng ml⁻¹ and the catalytic reaction activation energy was found to be 43.92 kJ mol⁻¹. The proposed method was tested for the determination of vanadium(V) in rice and natural water samples.     

Development of an extraction method for the determination of prostaglandins in biological tissue samples using liquid chromatography–tandem mass spectrometry: Application to gonads of Atlantic cod (Gadus morhua)

A simple extraction method for the analysis of PGE₂ and PGF_2α in gonad samples from Atlantic cod and further quantification by using liquid chromatography–tandem mass spectrometry is proposed. The evaluation of the best solvent extraction conditions and the analytical performance parameters are reported. The method was highly selective for both prostaglandins and the calibration curves, based on the internal standard method, were linear between 5 and 1000 ng mL⁻¹ for PGE₂ and PGF_2α, with limits of detection of 1 ng mL⁻¹ and 1.5 ng mL⁻¹ and recovery values of 99.999 ± 0.002 and 99.967 ± 0.023 respectively. The homogenization of samples using liquid nitrogen combined with the developed extraction protocol can be implemented in different types of biological tissues.     

Determination of the antidepressant paroxetine and its three main metabolites in human plasma by liquid chromatography with fluorescence detection

A high-performance liquid chromatographic method has been developed for the determination in human plasma of the specific serotonin reuptake inhibitor (SSRI) antidepressant paroxetine and its three main metabolites (M1, M2, M3). Fluorescence detection was used, exciting at λ = 294 nm and monitoring emission at λ = 330 nm for paroxetine (λ_exc = 280 nm, λ_em = 330 nm for M1 and M2; λ_exc = 268 nm, λ_em = 290 nm for M3). Separation was obtained on a reversed-phase C18 column using a mobile phase composed of 66.7% aqueous phosphate at pH 2.5 and 33.3% acetonitrile. Imipramine (λ_exc = 252 nm, λ_em = 390 nm) was used as the internal standard. A careful pre-treatment of plasma samples was developed, using solid-phase extraction with C8 cartridges (50 mg, 1 mL). The calibration curves were linear over a working range of 2.5-100 ng mL⁻¹ for paroxetine and of 5-100 ng mL⁻¹ for all metabolites. The limit of detection (LOD) was 1.2 ng mL⁻¹ for PRX and 2.0 ng mL⁻¹ for the metabolites. The method was applied with success to plasma samples from depressed patients undergoing treatment with paroxetine. Hence, the method seems to be suitable for the therapeutic drug monitoring of paroxetine and its main metabolites in depressed patients’ plasma.     

Kinetic method for determination of nanogram amounts of copper(II) by its catalytic effect on hexacynoferrate(III)-citric acid indicator reaction

This paper describes a highly sensitive, selective catalytic-kinetic-spectrophotometric method for the determination of copper(II) concentration as low as 6 ng ml⁻¹. The method is based on the catalytic effect of copper(II) on the oxidation of citric acid by alkaline hexacyanoferrate(III). The reaction was followed by measuring the decrease in absorbance of hexacyanoferrate(III) at 420 nm (λ_max of [Fe(CN)₆]³⁻, ∈ = 1020 dm³ mol⁻¹ cm⁻¹). The dependence of rate of the indicator reaction on the reaction variables has been studied and discussed to propose a suitable mechanism to get a relation between the reaction rate and [Cu²⁺]. A fixed time procedure has been used to obtain a linear calibration curve between the initial rate and lower [Cu²⁺] or log[Cu²⁺] in the range 1 × 10⁻⁷ to 4 × 10⁻⁴ mol l⁻¹ (6.35-25,400 ng ml⁻¹). The detection limit has been calculated to be 4 ng ml⁻¹. The maximum average error is 3.5%. The effect of the presence of various cations, commonly associated with copper(II) and some anions has also been investigated and discussed. The proposed method is sensitive, accurate, rapid and inexpensive compared to other techniques available for determination of copper(II) in such a large range of concentration. The new method has been successfully applied for the determination of copper(II) in various samples.     

Sensitive sandwich immunoassay based on single particle mode inductively coupled plasma mass spectrometry detection

A sensitive sandwich type immunoassay has been proposed with the detection by inductively coupled plasma mass spectrometry (ICP-MS) in a single particle mode (time resolved analysis). The signal induced by the flash of ions (¹⁹⁷Au⁺) due to the ionization of single Au-nanoparticle (Au-NP) label in the plasma torch can be measured by the mass spectrometer. The frequency of the transient signals is proportional to the concentration of Au-NPs labels. Characteristics of the signals obtained from Au-NPs of 20, 45 and 80 nm in diameters were discussed. The analytical figures for the determination of Au-labeled IgG using ICP-MS in conventional integral mode and single particle mode were compared in detail. Rabbit-anti-human IgG was used as a model analyte in the sandwich immunoassay. A detection limit (3σ) of 0.1 ng mL⁻¹ was obtained for rabbit-anti-human IgG after immunoreactions, with a linear range of 0.3-10 ng mL⁻¹ and a RSD of 8.1% (2.0 ng mL⁻¹). Finally, the proposed method was successfully applied to spiked rabbit-anti-human IgG samples and rabbit-anti-human serum samples. The method resulted to be a highly sensitive ICP-MS based sandwich type immunoassay.     

High-sensitivity detection of polysaccharide using phosphodiesters quaternary ammonium salt as probe by decreased resonance light scattering

Phosphodiesters quaternary ammonium salt (PQAS) displayed quite intense light scattering in aqueous solution under the optimum condition. In addition, the resonance light scattering (RLS) signal of PQAS was remarkably decreased after adding trace amount polysaccharide with the maximum peak located at 391 nm. It was found that the decreased RLS intensity of the PQAS − PPGL system (ΔI_RLS) was in proportion to PPGL concentration in the range of 0.1-30 ng mL⁻¹, with a lower detection limit of 0.05 ng mL⁻¹. Based on this rare decreased RLS phenomenon, the novel method of the determination of purified polysaccharide of Gracilaria Lemaneiformis (PPGL) at nanogram level was proposed in this contribution. The proposed approach was used to determine purified polysaccharide extracted from Gracilaria Lemaneiformis with satisfactory results. Compared with the reported polysaccharide assays, this proposed method has good selectivity, high sensitivity and is especially simple and convenient. Moreover, the mechanism of the reaction between PQAS and polysaccharide was investigated by RLS, fluorescence, and fluorescence lifetime spectra.     

Long-wavelength homogeneous enzyme immunoassay for the determination of amikacin in water samples

A simple and rapid homogeneous enzyme immunoassay involving the use of the malic dehydrogenase enzyme and a long-wavelength fluorophor, the oxazine Cresyl Violet, is proposed for the determination of the antibiotic amikacin in water samples. An enzymatic tracer has been synthesized by covalent binding of amikacin to malic dehydrogenase via a carbodiimide derivative. Free tracer catalyses the reaction between Cresyl Violet and malic acid giving rise to a decrease in the fluorescence of the fluorophor. Kinetic curves for this reaction have been monitored at λ_ex 585 and λ_em 624 nm using the stopped-flow mixing technique, being the initial rate measured in only 2-3 s. The dynamic range of the method is 1-15 ng mL⁻¹ and the detection limit is 0.3 ng mL⁻¹, using aqueous standard solutions or water samples. The precision, obtained at 1 and 5 ng mL⁻¹ and expressed as relative standard deviation, was 6.0 and 9.6%, respectively. The method has been applied to the analysis of drinking, river and wastewater samples. The sample pre-treatment involved a solid-phase extraction step for the clean-up of the samples. A recovery study was carried out to validate the method, being the values obtained in the range 80-114%, with a mean value of 96.7%.     

Two different spectrofluorimetric methods for simultaneous determination of gemfibrozil and rosiglitazone in human plasma

Two accurate, reliable, and highly sensitive spectrofluorimetric methods were developed for simultaneous determination of binary mixture gemfibrozil and rosiglitazone in human plasma without prior separation steps. The first method is based on synchronous fluorescence spectrometry using double scans. At Δλ = 27 nm, gemfibrozil yields detectable signal that is independent of the presence of rosiglitazone. Similarly, at Δλ = 120 nm the signal of rosiglitazone is not influenced by the presence of gemfibrozil. Signals at two wavelengths, 301 (Δλ = 27 nm) and 368 nm (Δλ = 120 nm) vary linearly with gemfibrozil and rosiglitazone concentrations over the range 100-700 ng mL⁻¹ (for gemfibrozil) and 20-140 ng mL⁻¹ (for rosiglitazone), respectively. The limits of detection (LOD) were 2.3 and 2.72 ng mL⁻¹ for gemfibrozil and rosiglitazone, respectively. The second method is based on the technique of simultaneous equations (Vierodt's method), in which 258 nm was selected as the excitation wavelength. Two equations are constructed based on the fact that at (λEm₂=302 nm of gemfibrozil) and (λEm₂=369 nm of rosiglitazone) the fluorescence of the mixture is the sum of the individual fluorescence of gemfibrozil and rosiglitazone. The limits of detection (LOD) were 28.1 and 23.63 ng mL⁻¹ for gemfibrozil and rosiglitazone, respectively. The proposed methods were successfully applied for the determination of the two compounds in synthetic mixtures and in human plasma with a good recovery.     

Development of an ICP-MS immunoassay for the detection of anti-erythropoietin antibodies

A sandwich-type immunoassay linked with inductively coupled plasma mass spectrometry (ICP-MS) has been developed for the detection of anti-erythropoietin antibodies (anti-EPO Abs). Recombinant human erythropoietin (rhEPO) was immobilized on the solid phase to capture anti-rhEPO Abs specifically. After the immunoreactions with Au-labeled goat-anti-rabbit IgG, a diluted HNO₃ (2%) was used to dissociate Au nanoparticles which was then introduced to the ICP-MS for measurements. Under the optimized conditions, the calibration graph for anti-EPO Abs was linear in the range of 35.6-500 ng mL⁻¹ with a detection limit of 10.7 ng mL⁻¹ (3σ, n = 9). The relative standard deviation (R.S.D.) for three replicate measurements of 30.9 ng mL⁻¹ of anti-EPO Abs was 8.43%. The recoveries of anti-EPO Abs in sera at the spiking level of 50, 100, 150, 200 and 400 ng mL⁻¹ were 99.2%, 101.5%, 95.0%, 94.0% and 102.9%, respectively. For the real sample analysis, 26 samples from healthy people and 53 samples from patients with rhEPO treatments were studied. One sample from patients showed significantly higher anti-EPO Abs from other samples, indicating a possibility of immune response of this patient.     

Facile, sensitive and selective fluorescence turn-on detection of HSA/BSA in aqueous solution utilizing 2,4-dihydroxyl-3-iodo salicylaldehyde azine

A novel fluorescence turn-on detection method of human serum albumin (HSA) and bovine serum albumin (BSA) in aqueous solution is investigated using 2,4-dihydroxyl-3-iodo salicylaldehyde azine (DISA). Upon the addition of DISA to HSA/BSA solution, a fluorescence turn-on effect at 529 nm can be observed with a large stokes shift of ∼129 nm based on hydrophobic binding-mode between protein and dye. Under the optimal condition, the linear ranges of fluorescence intensity for HSA and BSA are 0.1-30 μg mL⁻¹ with the relative correlation coefficient of R² = 0.991 (n = 10) and 0.3-50 μg mL⁻¹ with R² = 0.997 (n = 10); and the detection limits for HSA and BSA based on IUPAC (C_DL = 3S_b/m) are 20 ng mL⁻¹ and 50 ng mL⁻¹, respectively.     

Production and characterization of a broad-specificity polyclonal antibody for O,O-diethyl organophosphorus pesticides and a quantitative structure-activity relationship study of antibody recognition

Polyclonal antibody (PAb) with broad-specificity for O,O-diethyl organophosphorus pesticides (OPs) against a generic hapten, 4-(diethoxyphosphorothioyloxy)benzoic acid, was produced. The obtained PAb showed high sensitivity to seven commonly used O,O-diethyl OPs in a competitive indirect enzyme-linked immunosorbent assay (ciELISA) using a heterologous coating antigen, 4-(3-(diethoxyphosphorothioyloxy)phenylamino)-4-oxobutanoic acid. The 50% inhibition value (IC₅₀) was 348 ng mL⁻¹ for parathion, 13 ng mL⁻¹ for coumaphos, 22 ng mL⁻¹ for quinalphos, 35 ng mL⁻¹ for triazophos, 751 ng mL⁻¹ for phorate, 850 ng mL⁻¹ for dichlofenthion, and 1301 ng mL⁻¹ for phoxim. The limit of detection (LOD) met the ideal detection criteria of all the seven OP residues. A quantitative structure-activity relationship (QSAR) model was constructed to study the mechanism of antibody recognition using multiple linear regression analysis. The results indicated that the frontier-orbital energies (energy of the highest occupied molecular orbital, E_HOMO, and energy of the lowest unoccupied molecular orbital, E_LUMO) and hydrophobicity (log of the octanol/water partition coefficient, log P) were mainly responsible for the antibody recognition. The linear equation was log(IC₅₀) = −63.274E_HOMO + 15.985E_LUMO + 0.556 log P − 25.015, with a determination coefficient (r²) of 0.908.     

A novel gaseous pinacolyl alcohol sensor utilizing cataluminescence on alumina nanowires prepared by supercritical fluid drying

A cataluminescence (CTL) sensor using Al₂O₃ nanowires as the sensing material was developed for the determination of trace pinacolyl alcohol in air samples based on the catalytic chemiluminescence (CL) of pinacolyl alcohol on Al₂O₃ nanowires. Eight catalysts were examined and the CL intensity on Al₂O₃ nanowires prepared by supercritical fluid drying was the strongest. This novel CL sensor showed high sensitivity and selectivity to gaseous pinacolyl alcohol at optimal temperature of 340 °C. Quantitative analysis was performed at a wavelength of 460 nm. The linear range of CTL intensity versus concentration of gaseous pinacolyl alcohol was 0.09 × 10⁻⁶ to 2.56 × 10⁻⁶ g mL⁻¹ (r = 0.9983, n = 6) with a detection limit (3σ) of 0.0053 × 10⁻⁶ g mL⁻¹. None or only very low levels of interference were observed while the foreign substances such as water vapor, ethanol, ammonia, chloroform, benzene, nitrogen dioxide, methylbenzene, hydrochloric acid, methanol and butanol were passing through the sensor. The response time of the sensor is less than 100 s, and the sensor had a long lifetime more than 60 h. The sensor would be potentially applied to analysis of the nerve agents such as Soman.     

A novel immunoassay based on the dissociation of immunocomplex and fluorescence quenching by gold nanoparticles

This study reports a novel, simple and sensitive immunoassay using fluorescence quenching caused by gold nanoparticles coated with antibody. The method is based on a non-competitive heterogeneous immunoassay of human IgG conducted by the typical procedure of sandwich immunocomplex formation. Goat anti-human IgG was first adsorbed on polystyrene microwells, and human IgG analyte was captured by the primary antibody and then sandwiched by antibody labeled with gold nanoparticles. The sandwich-type immunocomplex was subsequently dissociated by the mixed solution of sodium hydroxide and trisodium citrate, the solution obtained, which contains gold nanoparticles coated with antibody, was used to quench fluorescence. The fluorescence intensity of fluorescein at 517 nm was inversely proportional to the logarithm of the concentration of human IgG in the dynamic range of 10-5000 ng mL⁻¹ with a detection limit of 4.7 ng mL⁻¹. The electrochemical experiments and the UV-vis measurements were applied to demonstrate whether the immunoglod was dissociated completely and whether the gold nanoparticles aggregated after being dissociated, respectively. The proposed system can be extended to detect target molecules such as other kinds of antigen and DNA strands, and has broad potential applications in disease diagnosis.     

Enzyme-linked immunosorbent assays for the insecticide fenitrothion. Influence of hapten conformation and sample matrix on assay performance

This study aimed at developing competitive enzyme-linked immunosorbent assays (ELISAs) for the organophosphorus (OP) insecticide fenitrothion using a monoclonal antibody. The hapten used to obtain the antibody had an ideal structural feature that allowed minimal functional group sacrifice. By using the antibody and a coating antigen, a competitive indirect ELISA was developed, which showed an IC₅₀ of 14 ng mL⁻¹ with a detection limit of 3.0 ng mL⁻¹. A competitive direct ELISA using an enzyme tracer was also developed, which showed an IC₅₀ of 17 ng mL⁻¹ with a detection limit of 1.6 ng mL⁻¹. The antibodies in both assays showed negligible cross-reactivity with the metabolites of fenitrothion and other OP pesticides except with the insecticides parathion-methyl and parathion-ethyl. Recoveries of fenitrothion from fortified rice and lettuce samples were determined and the bias in the recovery values was rationalized by using the standard curves obtained in the matrix extract.