Pressurised hot-water extraction of brominated flame retardants in sediment samples

Summary A pressurised, hot-water extraction (PHWE) method was developed for brominated flame-retardants in sediments. The effect of extraction time, temperature and pressure on PHWE recovery was investigated, together with solid-phase collection parameters (trapping material, length of trapping column, eluent composition). The concentrated extracts were analysed by GC-MS. PHWE recoveries were compared with those obtained by conventional Soxhlet-extraction. In general, recoveries were much higher with PHWE than with Soxhlet.     

Bromine determination in polymers by inductively coupled plasma-mass spectrometry and its potential for fast first screening of brominated flame retardants in polymers and paintings

The impact of brominated flame retardants (BFRs) on the environment and their potential risk in animal and human health is a present concern. Therefore, existing legislation in the European Union demands that polymers with BFRs are identified and eliminated from the recycling process due to their potential health hazard.In this work, a flow-injection (FI) system coupled to inductively coupled plasma-mass spectrometry (ICP-MS) was optimized for the detection of traces of bromine in polymers, plastic paints and enamels containing BFRs. Sample preparation requires a microwave-assisted digestion in order to transfer bromine in polymeric samples to solution. After appropriate optimization of the digestion procedure and the ICP-MS detection, a detection limit (DL) of 4.2 mg kg⁻¹ was obtained for synthesized polyurethane standards containing known concentrations of bromine. The precision of the proposed method, evaluated as the R.S.D. of signals obtained for three replicates of polymeric standard BFRs at the normative EU level, was as low as 3.6%.This simple developed methodology was characterized for the screening of bromine in polymeric matrices. The proposed system provides rapid binary yes/no overall responses, being appropriate for the screening of bromine above a pre-set concentration threshold. The unreliability region (UR), given by the probability of false positives and false negatives (set at 5% in both cases), was in the range between 442 and 678 mg kg⁻¹ of bromine (at a cut-off level of 0.1% in BFRs by weight of homogeneous material fixed by the EU normative). Finally, the applicability of the proposed screening system was tested for the reliable control of bromine in different commercial samples including flame-retardant paints and enamels.     

Magnetic solid‐phase extraction of brominated flame retardants from environmental waters with graphene‐doped Fe3O4 nanocomposites

Graphene‐doped Fe₃O₄ nanocomposites were prepared by a solvothermal reaction of an iron source with graphene. The nanocomposites were characterized by transmission electron microscopy, atomic force microscopy, X‐ray diffraction, superconducting quantum interference, Raman spectroscopy, Fourier transform infrared spectroscopy, and X‐ray photoelectron spectroscopy. This nanomaterial has been used as a magnetic solid‐phase extraction sorbent to extract trace brominated flame retardants from environmental waters. Various extraction parameters were optimized including dosage and reusability of the nanocomposites, and pH of sample matrix. The reliability of the magnetic solid‐phase extraction protocol based on graphene‐doped Fe₃O₄ nanocomposites was evaluated by investigating the recoveries of 2,4,6‐tribromophenol, tetrabromobisphenol A, 4‐bromodiphenyl ether, and 4,4?‐dibromodiphenyl ether in water samples. Good recoveries (85.0–105.0%) were achieved with the relative standard deviation ranging from 1.1–7.1%. Moreover, it is speculated from characterization and magnetic solid‐phase extraction experiment that there is not only π–π stacking but also possible hydrophobic interaction between the graphene‐doped Fe₃O₄ nanocomposites and analytes.     

Brominated flame retardants in the European chemicals policy of REACH-Regulation and determination in materials

The EU REACH legislation will require the registration of 30,000 currently marketed chemicals, including the main commercial BFRs in use (Deca-BDE, HBCD and TBBP-A). Much of the data needed for registration are already available, thanks to risk assessments of continued production and use already undertaken in the EU. Within the authorisation, substitution by less hazardous chemicals is encouraged. Both qualitative and quantitative methods for the analysis of flame-retarded polymers are needed in order that the identity and concentration of the BFRs can be established and compliance with regulations including the RoHS Directive demonstrated. These are reviewed.     

Headspace solid-phase microextraction gas chromatography tandem mass spectrometry for the determination of brominated flame retardants in environmental solid samples

A headspace solid-phase microextraction gas chromatography coupled with tandem mass spectrometry (HSSPME-GC-MS-MS) methodology for determination of brominated flame retardants in sediment and soil samples is presented. To the best of our knowledge, this is the first time that SPME has been applied to analyze polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) in environmental solid samples. Analyses were performed using 0.5-g solid samples moisturized with 2 mL water, employing a polydimethylsiloxane (PDMS) fiber coating, exposed to the headspace at 100 °C for 60 min. Several types of environmental solid samples were included in this study and the extraction efficiency was related to the organic matter content of the sample. Calibration was performed using real samples, and the method showed good linearity over a wide concentration range, precision, and afforded quantitative recoveries. The obtained detection limits were in the sub-ng g⁻¹ for all the target analytes in both samples. The proposed procedure was applied to several marine and river sediments and soils, some of which were found to contain PBDEs at concentrations in the ng g⁻¹ level; BDE-47, BDE-100, and BDE-99 were the major congeners detected. The proposed method constitutes a rapid and low-cost alternative for the analysis of the target brominated flame retardants in environmental solid samples, since the clean-up steps, fractionation, and preconcentration of extracts inherent to the classical multi-step solvent extraction procedures are avoided.      

A hybrid monolithic column based on flower-shaped zeolitic imidazolate framework for efficient capillary microextraction of brominated flame retardants

A novel flower-shaped zeolitic imidazolate framework (ZIF) doped organic-inorganic hybrid monolithic column (ZIF-HMC) was prepared by a simple sol-gel “one-step” method and utilized for efficient capillary microextraction (CME) of four brominated flame retardants. The prepared monolithic was characterized by Fourier transform infrared, scanning electron microscopy, X-ray photoelectron spectroscopy, energy disperse spectroscopy, and N₂ adsorption-desorption. The parameters of CME were optimized by orthogonal array design. Under the optimal conditions, the ZIF-HMC showed excellent extraction efficiency, the limit of detection (LODs) and the limit of quantification (LOQs) were in the range of 0.52∼3.1 μg/L and 1.7∼10 μg/L, respectively, and the proposed method demonstrated good recovery (88.8%–116.6%) with the RSD less than 13.6% and a reusability of at least 30 times. The ZIF-HMC possessed great potential for separating organic pollutants and the strategy used here could be extended to prepare other derivatized HMC functionalized monoliths.     

Results of an interlaboratory comparison on the determination of polybrominated flame retardants in poly(ethyleneterephthalate)

An intercomparison to establish the performance of routine laboratories in the determination of polybrominated flame retardants in polymers was organised. Commercial poly(ethyleneterephthalate) was fortified with technical pentabromodiphenyl ether, octabromodiphenyl ether and decabromodiphenyl ether mixtures and with a decabromobiphenyl technical mixture at 0.4–0.8 g/kg. Homogeneity and stability of the total Br content in the material was confirmed. Thirty-seven laboratories from Europe, Asia and the Americas submitted results. Relative repeatability standard deviations for individual congeners ranged from 7 to 17%. Relative between-laboratory standard deviations ranged from 22 to 61%. No significant influence of a common standard, application of a standard method or method parameters could be identified. The quality and uncertainty of the results of this study are significantly worse than those reported in the environmental field and indicate a clear need for a learning process among the laboratories involved. Figure Mandel’s h (between labs): critical level: 1.91     

Probing new approaches using atmospheric pressure photo ionization for the analysis of brominated flame retardants and their related degradation products by liquid chromatography-mass spectrometry

Atmospheric pressure photo ionisation has been evaluated for the analysis of brominated flame retardants and their related degradation products by LC-MS. Degradation mixtures obtained from the photochemical degradation of tetrabromobisphenol A and decabromodiphenylether were used as model systems for the assessment of the developed methodology. Negative ion mode gave best results for TBBPA and its degradation compounds. [M - H]- ions were formed without the need of using a doping agent. MS and MS/MS experiments allowed the structural identification of new TBBPA "polymeric" degradation compounds formed by attachment of TBBPA moieties and/or their respective cleavage products. In the case of polybromodiphenylethers, the positive mode provided M*+ ions and gave better results for congeners ranging from mono- to pentabromodiphenylethers whereas for higher bromination degrees, the negative ion mode (providing [M - Br + O]- ions) was best suited. Under both positive and negative ionisation modes, the use of toluene as doping agent gave better results. Liquid chromatography-mass spectrometry by means of atmospheric pressure photo-ionisation was applied to the analysis of aromatic brominated flame retardants and their degradation products. This methodology proved to be particularly useful, for the characterisation and structural identification of some compounds which are not amenable to GC-MS, especially in the case of apolar "polymeric" degradation products of tetrabromobisphenol A investigated in this work.     

Microwave-assisted extraction followed by headspace solid-phase microextraction and gas chromatography with mass spectrometry detection (MAE-HSSPME-GC-MS/MS) for determination of polybrominated compounds in aquaculture samples

This paper describes the first validated method for the extraction, purification and determination of trace levels of a number of pollutants of growing concern, including polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs), in aquaculture feeds and products. The new procedure comprises microwave-assisted extraction (MAE; optimized, using a central composite experimental design, to 15 min at 85 °C in 14 mL of 1:1 hexane/dichloromethane), and concentration by headspace solid-phase microextraction (HSSPME), and separation/quantification by gas chromatography with mass spectrometry detection (GC-MS/MS). The method was validated on the reference materials IAEA-406 and WMF-01. Limits of detection for fourteen of the fifteen analytes considered range from 10 to 600 pg g⁻¹, and limits of quantification from 50 pg g⁻¹ to 1.9 ng g⁻¹. Linear ranges, accuracies and precisions are reported.     

Microwave-assisted extraction (MAE) for the determination of polybrominated diphenylethers (PBDEs) in sewage sludge

An efficient microwave-assisted extraction (MAE) method has been developed and evaluated for the quantification of eight major polybrominated diphenylethers (PBDEs) in sewage sludge. The PBDEs were extracted from wet and dry sludge in a microwave extraction unit using a hexane/acetone mixture for 35 min at a controlled temperature of 130 °C. The extract was concentrated, cleaned up on a silica gel column, and analyzed by gas chromatography/mass spectrometry (GC/MS) in the negative chemical ionization (NCI) mode. The MAE procedure exhibited higher extraction efficiency, specifically for BDE (brominated diphenylether) 209, than the conventional Soxhlet extraction. The test congeners were clearly separated under specific instrumental operating conditions, at a source temperature of 230 °C and a column length of 20 m. The present analytical method showed recovery efficiencies ranging from 80 to 110% when applied to the PBDE-free sludge spiked with eight PBDE congeners. The efficiency of the MAE method was confirmed using sludge obtained from four sewage treatment plants (STPs). The results indicate that BDE 47, 99, and 209 are the most abundant congeners present in these sewage sludges, which is consistent with previous reports.     

Analysis of flame retardant additives in polymer fractions of waste of electric and electronic equipment (WEEE) by means of HPLC-UV/MS and GPC-HPLC-UV

An HPLC-UV/MS method has been developed to identify and quantify flame retardants in post-consumer plastics from waste of electric and electronic equipment (WEEE). Atmospheric pressure chemical ionisation spectra of 15 brominated and phosphate-based flame retardants were recorded and interpreted. The method was applied to detect flame retardant additives in polymer extracts obtained from pressurised liquid extraction of solid polymers. In addition, a screening method was developed for soluble styrene polymers to isolate a flame retardant fraction through the application of gel permeation chromatography (GPC). This fraction was transferred to an online-coupled HPLC column and detected by UV spectroscopy, which allowed a reliable qualitative and quantitative analysis of brominated flame retardants in the polymer solutions.     

Non-destructive rapid analysis of brominated flame retardants in electrical and electronic equipment using Raman spectroscopy.

Using Raman spectroscopy without any preparation, we analyzed the brominated flame retardant, polybromodiphenyl ethers (PBDEs), which has been prohibited by the European Union. The typical Raman bands of PBDEs, which are clearly different from those of other brominated flame retardants, are from 100 to 300 cm(-1). In our analysis, the detection limit was about 100 ppm, and the analysis took about 1 min, whereas the usual method of solvent extraction using gas chromatography/mass spectroscopy takes 50 h.     

A rapid method for the determination of brominated flame retardant concentrations in plastics and textiles entering the waste stream

Due to new European legislation, products going to waste are subject to ‘low persistent organic pollutant concentration limits’. Concentrations of restricted brominated flame retardants in waste products must be determined. A rapid extraction and clean‐up method was developed for determination of brominated flame retardants in various plastics and textiles. The optimised method used vortexing and ultrasonication in dichloromethane followed by sulfuric acid clean‐up to determine target compounds. Poly‐brominated diphenyl ethers were determined by gas chromatography with mass spectrometry and hexabromocyclododecane by liquid chromatography with tandem mass spectrometry. Good recoveries of target analytes were obtained after three extraction cycles. The method was validated using poly‐propylene and poly‐ethylene certified reference materials as well as previously characterised textiles, expanded and extruded poly‐styrene samples. Measured concentrations of target compounds showed good agreement with the certified values indicating good accuracy and precision. Clean extracts provided low noise levels resulting in low limits of quantification (0.8–1.5 ng/g for poly‐brominated diphenyl ethers and 0.3 ng/g for α‐, β‐ and γ‐hexabromocyclododecane). The developed method was applied successfully to real consumer products entering the waste stream and it provided various advantages over traditional methods, including reduced analysis time, solvent consumption, minimal sample contamination and high sample throughput, which is crucial to comply with the implemented legislation.     

Processing and properties of engineering plastics recycled from waste electrical and electronic equipment (WEEE)

The characteristics of engineering plastics used in the preparation of electrical and electronic equipment were studied. More specifically, their thermal response was recorded by DSC experiments, the rheological properties were investigated via MFI tests and the mechanical properties were evaluated with tensile tests. The aim was to establish a procedure for recycling the same engineering plastics deriving from waste of electrical and electronic equipment (WEEE), which offers the additional advantage of using the as-received waste stream as a recyclable mixture, i.e. without sorting and classification of its components.The experimental results showed that blends of PC with ABS or ABS/HIPS can be prepared by direct mixing and this, would allow easy handling of the engineering plastics coming from WEEE, i.e. blending without the need of sorting. These mixtures can be easily processed and display acceptable mechanical properties with reasonable cost. Therefore, the processing characteristics and properties of the systems studied in this work could be the key for the design of an interesting approach for handling solid plastic waste from electrical and electronic devices.     

Thermogravimetric investigation ofwastes from electrical and electronic equipment (WEEE)

Two components of electronic wastes (sample A – a mixture of three types of printed circuit boards, sample B – a mixture of electronic junctions with metal wires) were investigated using thermogravimetric analysis (TG). Thermogravimetric and derivative thermogravimetric data (TG and DTG) give information on the thermal stability of A and B samples and allows finding the correct conditions for their degradation using pyrolysis in an experimental system, built on the laboratory scale for utilization of hazardous wastes. X-ray fluorescence measurements prove that brominated flame retardant is present in sample A, whilst chlorinated flame retardant is a probable component of sample B. Preliminary liquid chromatography of oil products obtained as a result of thermal waste degradation shows that the hydrocarbons released during pyrolysis could be used as a fuel.     

Application of polydimethylsiloxane rod extraction to the determination of sixteen halogenated flame retardants in water samples

An extraction and preconcentration procedure for the determination in water samples of several halogenated flame retardants (FRs), nine brominated diphenyls ethers (BDEs) and seven non-BDE FRs, was developed and validated. The optimised procedure is based on polydimethylsiloxane (PDMS) rods as sorptive extraction material, followed by liquid desorption and gas chromatography coupled to negative chemical ionisation–mass spectrometry (GC–NCI–MS) determination, rendering an efficient and inexpensive method. The final optimised protocol consists of overnight extraction of 100 mL of sample solutions containing 40% MeOH and 4% NaCl, followed by a 15-min sonication-assisted desorption with 300 μL of ethyl acetate, solvent evaporation and GC–NCI–MS analysis. Under these conditions, extraction efficiencies in the 9 to 70% range were obtained, leading to enrichment factors between 108 and 840, detection limits in the range from 0.4 to 10 ng L⁻¹and RSD values in the 2–23% range. After method validation, different real water samples, including river, ria, sea, landfill leachate, influent and effluent wastewater from an urban sewage treatment plant (STP) and effluent wastewater from a textile industry, were analysed. BDE-47, BDE-99, BDE-100 and BDE-197 were detected in wastewater and landfill leachate samples at concentration levels up to 2887 ng L⁻¹. Among the non-BDE FRs, bis (2-ethylhexyl)-3,4,5,6-tetrabromo-phthalate (DEHTBP) was detected in surface water samples (sea, river and ria) between 1.3 and 2.2 ng L⁻¹ and 1,2-bis(2,4,6-tribromophenoxy)ethane (BTBPE) in the landfill leachate (64 ng L⁻¹).     

微波辅助萃取-气相色谱/串联质谱法快速测定纺织品中禁用有机磷阻燃剂

以丙酮为萃取溶剂,采用微波辅助萃取技术对纺织品中禁用有机磷阻燃剂进行萃取,萃取液进行气相色谱/串联质谱测定,从而建立了一种微波萃取-气相色谱/串联质谱分析方法,对纺织品中禁用有机磷阻燃剂进行了测定。6种禁用有机磷阻燃剂三-(1-氮杂环丙烯基)氧化膦(TEPA)、三-(2-氯乙基)磷酸酯(TCEP)、三-(2,3-二氯丙基)磷酸酯(TDCP)、二-(2,3-二溴丙基)磷酸酯(DDBPP)、三-(邻甲苯基)磷酸酯(TOCP)和三-(2,3-二溴丙基)磷酸酯(TRIS)的线性范围分别为9.17~366.80、0.95~75.98、1.04~83.20、41.60~832.00、3.80~75.90、40.48~809.60 ?g/L,在S/N=10的条件下,检出限分别为3.0、0.2、0.3、25.0、2.5、29.0 ?g/kg。方法精密度为3.80~8.79 %,回收率为82.62~96.88 %。气相色谱/串联质谱母离子和子离子一一对应的多反应监测模式有效地去除了基体杂质干扰和假阳性现象。该方法简便快速、灵敏度高,定性准确,可完全满足纺织品中禁用有机磷阻燃剂的检测要求。     

Extraction of brominated flame retardants from polymeric waste material using different solvents and supercritical carbon dioxide

Different procedures were examined to extract pure and high concentrations of a series of brominated flame retardants from various polymer materials. These procedures include supercritical carbon dioxide (sc-CO₂), modified sc-CO₂, solvent and soxhlet extraction. Extraction with sc-CO₂ gave low extraction efficiencies (between 6 and 20%) probably due to the low pressure of sc-CO₂ used. The use of toluene, acetonitrile and THF as modifier in sc-CO₂ raised the extraction efficiencies for many flame retardants. High extraction efficiencies were achieved for tetrabromobisphenol A (TBBPA), TBBPA-bis-(2,3-dibromopropylether) (TBBPA-dbp), TBBPA-carbonatoligomer (TBBPA-co) and decabromodiphenylether (DECA) (between 93 and 100%) by using 1-propanol as solvent during soxhlet extraction. Toluene instead of 1-propanol was used where insufficient extraction of the flame retardant occurred. The materials (before and after extraction) were analysed with energy dispersive X-ray fluorescence analysis (EDXRF), high performance liquid chromatography with ultraviolet detection (HPLC/UV), gas chromatography/mass spectrometry (GC/MS) and infrared spectroscopy (IR) techniques. The properties of the extracted flame retardants such as TBBPA, TBBPA-dbp and 1,2-bis(tribromophenoxy)-ethane (TBPE) are in good agreement with those of standard reference materials.     

Methods for the determination of phenolic brominated flame retardants, and by-products, formulation intermediates and decomposition products of brominated flame retardants in water

Brominated flame retardants (BFRs) are the chemicals of high importance within the REAch framework. In addition to polybrominated diphenyl ethers (PBDEs), hexabromocyclododecane (HBCD) and tetrabromobisphenol A (TBBPA), other BFRs such as bromophenols, intermediates in FR formulation like bromoanilines, and their brominated and non-brominated by-products such as bromoanisoles, bromotoluenes, bromoalkanes and 1,5,9-cyclododecatriene, respectively should be monitored and controlled because of their toxicity and their very low odour and taste thresholds, below sub-nanogram-per liter levels. In the present study several analytical methods for the simultaneous determination, i.e., combining one single sample treatment and one analysis step, of these compounds in water have been developed, optimized and evaluated. The methods involve a (pre-concentration)-extraction technique, such as liquid-liquid (LLE), solid-phase (SPE), headspace (HS) extraction or solid-phase microextraction (SPME), followed by gas chromatography (GC)-mass spectrometry (MS) analysis with either electron capture negative ionization (ECNI) or electron impact (EI) as ionization techniques. ECNI is more sensitive than EI for analytes with more than one bromine atom. HS and SPME were previously optimized by means of a multifactorial experimental design. Extraction temperature and the liquid/headspace volume ratio were the most significant factors in HS extraction. In SPME, the variables studied were the nature of the fiber, the mode of extraction and the extraction temperature. Polydimethylsiloxane (PDMS) fibers appeared to be more suitable than carboxen-polydimethylsiloxane (CAR-PDMS) for the analysis of the target compounds with more than one bromine atom. The extraction of 2,4-dibromoaniline was only achieved in a direct immersion mode, in which the optimal extraction temperature was 60 degrees C. The methods LLE-GC-(ECNI)MS, LLE-GC-(EI)MS, SPE-GC-(ECNI)MS, SPE-GC-(EI)MS, HS-GC-(EI)MS and SPME-GC-(EI)MS were evaluated in terms of linearity, precision, detection limits and trueness. All methods, with the exception of HS-GC-(EI)MS, were linear in a range of at least two orders of magnitude, giving recoveries above 75% and detection limits at the low ng/L level for most of the target analytes. SPE-GC-(ECNI)MS is the most sensitive and reliable method for the determination of most of the bromine compounds, whereas SPE-GC-(EI)MS is the most suitable to quantify the three isomers of 1,5,9-cyclododecatriene. Both methods together with SPME-GC-(EI)MS (for qualitative confirmation) were applied to water samples from the Western Scheldt (The Netherlands), where 2,6-dibromophenol and 2,4,6-tribromoanisole could be detected at levels higher than their respective odour thresholds.     

固相萃取-气相色谱/质谱联用法测定儿童手推车中3种有机磷酸酯阻燃剂

有机磷酸酯是一类重要的磷系阻燃剂,由于其具有类似持久性有机污染物(persistent organic pollutants, POPs)的性质,欧美等国家已纷纷设立相关法规限制其在儿童用品中的使用。目前国际和国内均未有儿童手推车中有机磷酸酯阻燃剂的检测标准。本文建立了儿童手推车中3种有机磷酸酯阻燃剂的超声萃取-弗罗里硅土固相萃取柱净化-气相色谱/质谱检测方法。该方法的加标回收率为89.5%~107.3%,检出限(3S/N)为0.01 mg/kg,定量限(10S/N)为0.1 mg/kg,能较好地排除基质干扰,适用于儿童手推车软垫材料中3种有机磷酸酯的定性和定量分析。37个样品的分析结果表明,磷酸三(2-氯丙基)酯(TCPP)的检出率为81.1%,含量范围为1.0~15312.8 mg/kg,依据欧盟玩具新指令2014/79/EU, TCPP超标(> 5 mg/kg)率为32.4%;其中2个样品中还检出了磷酸三(2-氯乙基)酯(TCEP)和磷酸三(1,3-二氯-2-丙基)酯(TDCP),含量范围为6.2~44.1 mg/kg,均已超标。可见,市场上的儿童手推车存在较高的有机磷酸酯阻燃剂暴露风险。